/* bspstart.c
*
* This set of routines starts the application. It includes application,
* board, and monitor specific initialization and configuration.
* The generic CPU dependent initialization has been performed
* before this routine is invoked.
*
* COPYRIGHT (c) 1989-2007.
* On-Line Applications Research Corporation (OAR).
*
* The license and distribution terms for this file may be
* found in the file LICENSE in this distribution or at
* http://www.rtems.com/license/LICENSE.
*
* Modifications for MBX860:
* Copyright (c) 1999, National Research Council of Canada
*
* $Id$
*/
#include <string.h>
#include <bsp.h>
#include <bsp/irq.h>
#include <rtems/libio.h>
#include <rtems/libcsupport.h>
#include <rtems/bspIo.h>
#include <libcpu/cpuIdent.h>
#include <libcpu/spr.h>
#include <rtems/powerpc/powerpc.h>
SPR_RW(SPRG0)
SPR_RW(SPRG1)
extern unsigned long intrStackPtr;
/*
* Driver configuration parameters
*/
uint32_t bsp_clicks_per_usec;
uint32_t bsp_clock_speed;
uint32_t bsp_serial_per_sec; /* Serial clocks per second */
boolean bsp_serial_external_clock;
boolean bsp_serial_xon_xoff;
boolean bsp_serial_cts_rts;
uint32_t bsp_serial_rate;
uint32_t bsp_timer_average_overhead; /* Average overhead of timer in ticks */
uint32_t bsp_timer_least_valid; /* Least valid number from timer */
boolean bsp_timer_internal_clock; /* TRUE, when timer runs with CPU clk */
/*
* Use the shared implementations of the following routines.
* Look in rtems/c/src/lib/libbsp/shared/bsppost.c and
* rtems/c/src/lib/libbsp/shared/bsplibc.c.
*/
void bsp_libc_init( void *, uint32_t, int );
void BSP_panic(char *s)
{
printk("%s PANIC %s\n",_RTEMS_version, s);
__asm__ __volatile ("sc");
}
void _BSP_Fatal_error(unsigned int v)
{
printk("%s PANIC ERROR %x\n",_RTEMS_version, v);
__asm__ __volatile ("sc");
}
/*
* bsp_pretasking_hook
*
* Called when RTEMS initialization is complete but before interrupts and
* tasking are enabled. Used to setup libc and install any BSP extensions.
*
* Must not use libc (to do io) from here, since drivers are not yet
* initialized.
*
* Input parameters: NONE
*
* Output parameters: NONE
*
* Return values: NONE
*/
void bsp_pretasking_hook(void)
{
/*
* These are assigned addresses in the linkcmds file for the BSP. This
* approach is better than having these defined as manifest constants and
* compiled into the kernel, but it is still not ideal when dealing with
* multiprocessor configuration in which each board as a different memory
* map. A better place for defining these symbols might be the makefiles.
* Consideration should also be given to developing an approach in which
* the kernel and the application can be linked and burned into ROM
* independently of each other.
*/
extern unsigned char _HeapStart;
extern unsigned char _HeapEnd;
bsp_libc_init( &_HeapStart, &_HeapEnd - &_HeapStart, 0 );
#ifdef RTEMS_DEBUG
rtems_debug_enable( RTEMS_DEBUG_ALL_MASK );
#endif
}
/*
* bsp_start()
*
* Board-specific initialization code. Called from the generic boot_card()
* function defined in rtems/c/src/lib/libbsp/shared/main.c. That function
* does some of the board independent initialization. It is called from the
* MBX8xx entry point _start() defined in
* rtems/c/src/lib/libbsp/powerpc/mbx8xx/startup/start.S
*
* _start() has set up a stack, has zeroed the .bss section, has turned off
* interrupts, and placed the processor in the supervisor mode. boot_card()
* has left the processor in that state when bsp_start() was called.
*
* RUNS WITH ADDRESS TRANSLATION AND CACHING TURNED OFF!
* ASSUMES THAT THE VIRTUAL ADDRESSES WILL BE IDENTICAL TO THE PHYSICAL
* ADDRESSES. Software-controlled address translation would be required
* otherwise.
*
* Input parameters: NONE
*
* Output parameters: NONE
*
* Return values: NONE
*/
void bsp_start(void)
{
extern void *_WorkspaceBase;
ppc_cpu_id_t myCpu;
ppc_cpu_revision_t myCpuRevision;
register unsigned char* intrStack;
/*
* Get CPU identification dynamically. Note that the get_ppc_cpu_type() function
* store the result in global variables so that it can be used latter...
*/
myCpu = get_ppc_cpu_type();
myCpuRevision = get_ppc_cpu_revision();
mmu_init();
/*
* Enable instruction and data caches. Do not force writethrough mode.
*/
#if NVRAM_CONFIGURE == 1
if ( nvram->cache_mode & 0x02 )
rtems_cache_enable_instruction();
if ( nvram->cache_mode & 0x01 )
rtems_cache_enable_data();
#else
#ifdef INSTRUCTION_CACHE_ENABLE
rtems_cache_enable_instruction();
#endif
#ifdef DATA_CACHE_ENABLE
rtems_cache_enable_data();
#endif
#endif
/*
* Initialize some SPRG registers related to irq handling
*/
intrStack = (((unsigned char*)&intrStackPtr) - PPC_MINIMUM_STACK_FRAME_SIZE);
_write_SPRG1((unsigned int)intrStack);
/* signal them that we have fixed PR288 - eventually, this should go away */
_write_SPRG0(PPC_BSP_HAS_FIXED_PR288);
/*
* Install our own set of exception vectors
*/
initialize_exceptions();
/*
* Allocate the memory for the RTEMS Work Space. This can come from
* a variety of places: hard coded address, malloc'ed from outside
* RTEMS world (e.g. simulator or primitive memory manager), or (as
* typically done by stock BSPs) by subtracting the required amount
* of work space from the last physical address on the CPU board.
*
* In this case, the memory is not malloc'ed. It is just
* "pulled from the air".
*/
Configuration.work_space_start = (void *)&_WorkspaceBase;
/*
* initialize the device driver parameters
*/
#if ( defined(mbx860_001b) || \
defined(mbx860_002b) || \
defined(mbx860_003b) || \
defined(mbx860_003b) || \
defined(mbx860_004b) || \
defined(mbx860_005b) || \
defined(mbx860_006b) || \
defined(mbx821_001b) || \
defined(mbx821_002b) || \
defined(mbx821_003b) || \
defined(mbx821_004b) || \
defined(mbx821_005b) || \
defined(mbx821_006b))
bsp_clicks_per_usec = 0; /* for 32768Hz extclk */
#else
bsp_clicks_per_usec = 1; /* for 4MHz extclk */
#endif
bsp_serial_per_sec = 10000000;
bsp_serial_external_clock = 1;
bsp_serial_xon_xoff = 0;
bsp_serial_cts_rts = 1;
bsp_serial_rate = 9600;
#if ( defined(mbx821_001) || defined(mbx821_001b) || defined(mbx860_001b) )
bsp_clock_speed = 50000000;
bsp_timer_average_overhead = 3;
bsp_timer_least_valid = 3;
#else
bsp_clock_speed = 40000000;
bsp_timer_average_overhead = 3;
bsp_timer_least_valid = 3;
#endif
m8xx.scc2.sccm=0;
m8xx.scc2p.rbase=0;
m8xx.scc2p.tbase=0;
m8xx_cp_execute_cmd( M8xx_CR_OP_STOP_TX | M8xx_CR_CHAN_SCC2 );
/*
* Initalize RTEMS IRQ system
*/
BSP_rtems_irq_mng_init(0);
#ifdef SHOW_MORE_INIT_SETTINGS
printk("Exit from bspstart\n");
#endif
}