path: root/c/src/lib/libbsp/powerpc/mbx8xx/startup/bspstart.c.nocache

/*  bspstart.c
 *
 *  This set of routines starts the application.  It includes application,
 *  board, and monitor specific initialization and configuration.
 *  The generic CPU dependent initialization has been performed
 *  before this routine is invoked.
 *
 *  COPYRIGHT (c) 1989-2007.
 *  On-Line Applications Research Corporation (OAR).
 *
 *  The license and distribution terms for this file may be
 *  found in the file LICENSE in this distribution or at
 *  http://www.rtems.com/license/LICENSE.
 *
 *  Modifications for MBX860:
 *  Copyright (c) 1999, National Research Council of Canada
 *
 *  $Id$
 */

#include <bsp.h>
 
/*
 *  Driver configuration parameters
 */
uint32_t   bsp_clicks_per_usec;
uint32_t   bsp_serial_per_sec;	       /* Serial clocks per second */
bool       bsp_serial_external_clock;
bool       bsp_serial_xon_xoff;
bool       bsp_serial_cts_rts;
uint32_t   bsp_serial_rate;
uint32_t   bsp_timer_average_overhead; /* Average overhead of timer in ticks */
uint32_t   bsp_timer_least_valid;      /* Least valid number from timer      */
bool       bsp_timer_internal_clock;   /* TRUE, when timer runs with CPU clk */

/*
 *  bsp_start()
 *
 *  Board-specific initialization code. Called from the generic boot_card()
 *  function defined in rtems/c/src/lib/libbsp/shared/main.c. That function
 *  does some of the board independent initialization. It is called from the
 *  MBX8xx entry point _start() defined in
 *  rtems/c/src/lib/libbsp/powerpc/mbx8xx/startup/start.S
 *
 *  _start() has set up a stack, has zeroed the .bss section, has turned off
 *  interrupts, and placed the processor in the supervisor mode. boot_card()
 *  has left the processor in that state when bsp_start() was called.
 *
 *  RUNS WITH ADDRESS TRANSLATION AND CACHING TURNED OFF!
 *  ASSUMES THAT THE VIRTUAL ADDRESSES WILL BE IDENTICAL TO THE PHYSICAL
 *  ADDRESSES. Software-controlled address translation would be required
 *  otherwise.
 *
 *  Input parameters: NONE
 *
 *  Output parameters: NONE
 *
 *  Return values: NONE
 */
void bsp_start(void)
{
  uint32_t   r1;

  mmu_init();
  
  /*
   * Enable instruction and data caches. Do not force writethrough mode.
   */
  #ifdef INSTRUCTION_CACHE_ENABLE
  r1 = M8xx_CACHE_CMD_ENABLE;
  _mtspr( M8xx_IC_CST, r1 );
  _isync;
  #endif

  /* 
   * Warning: EPPCBug 1.1 chokes to death if the data cache is turned on.
   * Set DATA_CACHE_ENABLE to zero in mbx8xx.cfg if EPPCBUG is used.
   */
  #ifdef DATA_CACHE_ENABLE
  r1 = M8xx_CACHE_CMD_ENABLE;
  _mtspr( M8xx_DC_CST, r1 );
  _isync;
  #endif
   
  /*
   *  initialize the device driver parameters
   */
  bsp_clicks_per_usec = 1;  /* for 4MHz extclk */
  bsp_serial_per_sec = 10000000;
  bsp_serial_external_clock = 1;
  bsp_serial_xon_xoff = 0;
  bsp_serial_cts_rts = 1;
  bsp_serial_rate = 9600;
#if ( defined(mbx821_001) || defined(mbx821_001b) || defined(mbx860_001b) )
  bsp_clock_speed = 50000000;
  bsp_timer_average_overhead = 3;
  bsp_timer_least_valid = 3;
#else
  bsp_clock_speed = 40000000;
  bsp_timer_average_overhead = 3;
  bsp_timer_least_valid = 3;
#endif

  m8xx.scc2.sccm=0;
  m8xx.scc2p.rbase=0;
  m8xx.scc2p.tbase=0;
  m8xx_cp_execute_cmd( M8xx_CR_OP_STOP_TX | M8xx_CR_CHAN_SCC2 );
}