1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
/* include/bspopts.h.in. Generated from configure.ac by autoheader. */
/* enables the data cache, if defined to a value other than zero */
#undef BSP_DATA_CACHE_ENABLED
/* If defined, then the BSP Framework will put a non-zero pattern into the
RTEMS Workspace and C program heap. This should assist in finding code that
assumes memory starts set to zero. */
#undef BSP_DIRTY_MEMORY
/* enables the instruction cache, if defined to a value other than zero */
#undef BSP_INSTRUCTION_CACHE_ENABLED
/* If defined, print a message and wait until pressed before resetting board
when application exits. */
#undef BSP_PRESS_KEY_FOR_RESET
/* If defined, reset the board when the application exits. */
#undef BSP_RESET_BOARD_AT_EXIT
/* If defined, then the BSP will use the Fast Ethernet Controller for
10/100MBit networking and used as primary networking interface. */
#undef BSP_USE_NETWORK_FEC
/* If defined, then the BSP will use the Serial Communications Controller
(SCC1) for 10MBit networking. */
#undef BSP_USE_NETWORK_SCC
/* (BSP--console driver) Must be defined to be one of CONS_CHN_SMC1,
CONS_CHN_SMC2, CONS_CHN_SCC1, CONS_CHN_SCC2, CONS_CHN_SCC3, or
CONS_CHN_SCC4. Determines which device will be registered as /dev/console.
*/
#undef CONSOLE_CHN
/* (BSP--SCC1 UART IF mode) Must be defined if SCC1 is used as a tty (UART)
channel. Set it to CONS_MODE_POLLED for polled operation, CONS_MODE_IRQ for
interrupt driven (spooled) operation. Set it to CONS_MODE_UNUSED, if not
used */
#undef CONS_SCC1_MODE
/* (BSP--SCC2 UART IF mode) Must be defined if SCC2 is used as a tty (UART)
channel. Set it to CONS_MODE_POLLED for polled operation, CONS_MODE_IRQ for
interrupt driven (spooled) operation. Set it to CONS_MODE_UNUSED, if not
used */
#undef CONS_SCC2_MODE
/* (BSP--SCC3 UART IF mode) Must be defined if SCC3 is used as a tty (UART)
channel. Set it to CONS_MODE_POLLED for polled operation, CONS_MODE_IRQ for
interrupt driven (spooled) operation. Set it to CONS_MODE_UNUSED, if not
used */
#undef CONS_SCC3_MODE
/* (BSP--SCC4 UART IF mode) Must be defined if SCC4 is used as a tty (UART)
channel. Set it to CONS_MODE_POLLED for polled operation, CONS_MODE_IRQ for
interrupt driven (spooled) operation. Set it to CONS_MODE_UNUSED, if not
used */
#undef CONS_SCC4_MODE
/* (BSP--SMC1 UART IF mode) Must be defined if SMC1 is used as a tty (UART)
channel. Set it to CONS_MODE_POLLED for polled operation, CONS_MODE_IRQ for
interrupt driven (spooled) operation. Set it to CONS_MODE_UNUSED, if not
used */
#undef CONS_SMC1_MODE
/* (BSP--SMC2 UART IF mode) Must be defined if SMC2 is used as a tty (UART)
channel. Set it to CONS_MODE_POLLED for polled operation, CONS_MODE_IRQ for
interrupt driven (spooled) operation. Set it to CONS_MODE_UNUSED, if not
used */
#undef CONS_SMC2_MODE
/* Define to the address where bug reports for this package should be sent. */
#undef PACKAGE_BUGREPORT
/* Define to the full name of this package. */
#undef PACKAGE_NAME
/* Define to the full name and version of this package. */
#undef PACKAGE_STRING
/* Define to the one symbol short name of this package. */
#undef PACKAGE_TARNAME
/* Define to the home page for this package. */
#undef PACKAGE_URL
/* Define to the version of this package. */
#undef PACKAGE_VERSION
/* (BSP--console driver) Must be defined to be one of CONS_CHN_SMC1,
CONS_CHN_SMC2, CONS_CHN_SCC2, CONS_CHN_SCC3, or CONS_CHN_SCC4. Determines
which device is used for output by printk(). If the port that printk() uses
is also used for other I/O (e.g. if PRINTK_CHN == CONSOLE_CHN), then both
ports should use the same type of I/O, otherwise the drivers will likely
conflict with each other. */
#undef PRINTK_CHN
/* (BSP--SPI board init function) Specify the function that inits the board
port lines and further devices. */
#undef SPI_BOARD_INIT_FNC
/* (BSP--SPI send address function) Specify the function that addresses SPI
devices. Set to bsp_dummy_spi_sel_addr for dummy implementation */
#undef SPI_SEND_ADDR_FNC
/* (BSP--SPI send stop function) Specify the function that deaddresses SPI
devices. Set to bsp_dummy_spi_send_stop for dummy implementation */
#undef SPI_SEND_STOP_FNC
|