1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
#ifndef RTEMS_BSP_VME_CONFIG_H
#define RTEMS_BSP_VME_CONFIG_H
/* $Id$ */
/* mvme3100 BSP specific address space configuration parameters */
/*
* Authorship
* ----------
* This software was created by
* Till Straumann <strauman@slac.stanford.edu>, 2002..2007,
* Stanford Linear Accelerator Center, Stanford University.
*
* Acknowledgement of sponsorship
* ------------------------------
* This software was produced by
* the Stanford Linear Accelerator Center, Stanford University,
* under Contract DE-AC03-76SFO0515 with the Department of Energy.
*
* Government disclaimer of liability
* ----------------------------------
* Neither the United States nor the United States Department of Energy,
* nor any of their employees, makes any warranty, express or implied, or
* assumes any legal liability or responsibility for the accuracy,
* completeness, or usefulness of any data, apparatus, product, or process
* disclosed, or represents that its use would not infringe privately owned
* rights.
*
* Stanford disclaimer of liability
* --------------------------------
* Stanford University makes no representations or warranties, express or
* implied, nor assumes any liability for the use of this software.
*
* Stanford disclaimer of copyright
* --------------------------------
* Stanford University, owner of the copyright, hereby disclaims its
* copyright and all other rights in this software. Hence, anyone may
* freely use it for any purpose without restriction.
*
* Maintenance of notices
* ----------------------
* In the interest of clarity regarding the origin and status of this
* SLAC software, this and all the preceding Stanford University notices
* are to remain affixed to any copy or derivative of this software made
* or distributed by the recipient and are to be affixed to any copy of
* software made or distributed by the recipient that contains a copy or
* derivative of this software.
*
* ------------------ SLAC Software Notices, Set 4 OTT.002a, 2004 FEB 03
*/
/*
* NOTE: the BSP (startup/bspstart.c) uses
* hardcoded window lengths that match this
* layout:
*/
#define _VME_A32_WIN0_ON_PCI 0xc0000000
#define _VME_CSR_ON_PCI 0xce000000
#define _VME_A24_ON_PCI 0xcf000000
#define _VME_A16_ON_PCI 0xcfff0000
/* start of the A32 window on the VME bus
* TODO: this should perhaps be a run-time configuration option
*/
#define _VME_A32_WIN0_ON_VME 0x20000000
/* if _VME_DRAM_OFFSET is defined, the BSP
* will map the board RAM onto the VME bus, starting
* at _VME_DRAM_OFFSET
*/
#define _VME_DRAM_OFFSET 0xc0000000
/* If your BSP requires a non-standard way to configure
* the VME interrupt manager then define the symbol
*
* BSP_VME_INSTALL_IRQ_MGR
*
* to a proper instruction sequence that installs the
* universe interrupt manager. This requires knowledge
* of the wiring between the universe and the PIC (main
* interrupt controller), i.e., which IRQ 'pins' of the
* universe are wired to which 'lines'/inputs at the PIC.
* (consult vmeUniverse.h for more information).
*
* When installing the universe IRQ manager it is also
* possible to specify whether it should try to share
* PIC interrupts with other sources. This might not
* be supported by all BSPs (but the unverse driver
* recognizes that).
*
* If BSP_VME_INSTALL_IRQ_MGR is undefined then
* the default algorithm is used (vme_universe.c):
*
* This default setup uses only a single wire. It reads
* the PIC 'line' from PCI configuration space and assumes
* this to be wired to the first (LIRQ0) IRQ input at the
* universe. The default setup tries to use interrupt
* sharing.
*/
#define BSP_VME_INSTALL_IRQ_MGR(err) \
do { \
err = vmeTsi148InstallIrqMgrAlt(\
VMETSI148_IRQ_MGR_FLAG_SHARED, /* use shared IRQs */ \
0, BSP_VME0_IRQ, \
1, BSP_VME1_IRQ, \
2, BSP_VME2_IRQ, \
3, BSP_VME3_IRQ, \
-1 /* terminate list */ \
); \
} while (0)
/* This BSP uses the Tsi148 Driver */
#define _VME_DRIVER_TSI148
#endif
|
