diff options
Diffstat (limited to 'bsps/include/libchip/smc91111.h')
| -rw-r--r-- | bsps/include/libchip/smc91111.h | 558 |
1 files changed, 0 insertions, 558 deletions
diff --git a/bsps/include/libchip/smc91111.h b/bsps/include/libchip/smc91111.h deleted file mode 100644 index 7ec83716d0..0000000000 --- a/bsps/include/libchip/smc91111.h +++ /dev/null @@ -1,558 +0,0 @@ -#ifndef _SMC91111_H_ -#define _SMC91111_H_ - -#include <libchip/smc91111exp.h> -#include <rtems/bspIo.h> - -#define LAN91CXX_TCR 0x00 -#define LAN91CXX_EPH_STATUS 0x01 -#define LAN91CXX_RCR 0x02 -#define LAN91CXX_COUNTER 0x03 -#define LAN91CXX_MIR 0x04 -#define LAN91CXX_MCR 0x05 /* Other than 91C111*/ -#define LAN91CXX_RPCR 0x05 /* 91C111 only*/ -#define LAN91CXX_RESERVED_0 0x06 -#define LAN91CXX_BS 0x07 -#define LAN91CXX_CONFIG 0x08 -#define LAN91CXX_BASE_REG 0x09 -#define LAN91CXX_IA01 0x0a -#define LAN91CXX_IA23 0x0b -#define LAN91CXX_IA45 0x0c -#define LAN91CXX_GENERAL 0x0d /* 91C96 - was "RESERVED_1" for others*/ -#define LAN91CXX_CONTROL 0x0e -#define LAN91CXX_BS2 0x0f -#define LAN91CXX_MMU_COMMAND 0x10 -#define LAN91CXX_PNR 0x11 -#define LAN91CXX_FIFO_PORTS 0x12 -#define LAN91CXX_POINTER 0x13 -#define LAN91CXX_DATA_HIGH 0x14 -#define LAN91CXX_DATA 0x15 -#define LAN91CXX_INTERRUPT 0x16 -#define LAN91CXX_BS3 0x17 -#define LAN91CXX_MT01 0x18 -#define LAN91CXX_MT23 0x19 -#define LAN91CXX_MT45 0x1a -#define LAN91CXX_MT67 0x1b -#define LAN91CXX_MGMT 0x1c -#define LAN91CXX_REVISION 0x1d -#define LAN91CXX_ERCV 0x1e -#define LAN91CXX_BS4 0x1f - -#define LAN91CXX_RCR_SOFT_RST 0x8000 /* soft reset*/ -#define LAN91CXX_RCR_FILT_CAR 0x4000 /* filter carrier*/ -#define LAN91CXX_RCR_ABORT_ENB 0x2000 /* abort on collision*/ -#define LAN91CXX_RCR_STRIP_CRC 0x0200 /* strip CRC*/ -#define LAN91CXX_RCR_RXEN 0x0100 /* enable RX*/ -#define LAN91CXX_RCR_ALMUL 0x0004 /* receive all muticasts*/ -#define LAN91CXX_RCR_PRMS 0x0002 /* promiscuous*/ -#define LAN91CXX_RCR_RX_ABORT 0x0001 /* set when abort due to long frame*/ - -#define LAN91CXX_TCR_SWFDUP 0x8000 /* Switched Full Duplex mode*/ -#define LAN91CXX_TCR_ETEN_TYPE 0x4000 /* ETEN type (91C96) 0 <=> like a 91C94*/ -#define LAN91CXX_TCR_EPH_LOOP 0x2000 /* loopback mode*/ -#define LAN91CXX_TCR_STP_SQET 0x1000 /* Stop transmission on SQET error*/ -#define LAN91CXX_TCR_FDUPLX 0x0800 /* full duplex*/ -#define LAN91CXX_TCR_MON_CSN 0x0400 /* monitor carrier during tx (91C96)*/ -#define LAN91CXX_TCR_NOCRC 0x0100 /* does not append CRC to frames*/ -#define LAN91CXX_TCR_PAD_EN 0x0080 /* pads frames with 00 to min length*/ -#define LAN91CXX_TCR_FORCOL 0x0004 /* force collision*/ -#define LAN91CXX_TCR_LLOOP 0x0002 /* local loopback (91C96)*/ -#define LAN91CXX_TCR_TXENA 0x0001 /* enable*/ - -#define LAN91CXX_POINTER_RCV 0x8000 -#define LAN91CXX_POINTER_AUTO_INCR 0x4000 -#define LAN91CXX_POINTER_READ 0x2000 -#define LAN91CXX_POINTER_ETEN 0x1000 -#define LAN91CXX_POINTER_NOT_EMPTY 0x0800 - - -#define LAN91CXX_INTERRUPT_TX_IDLE_M 0x8000 /* (91C96)*/ -#define LAN91CXX_INTERRUPT_ERCV_INT_M 0x4000 -#define LAN91CXX_INTERRUPT_EPH_INT_M 0x2000 -#define LAN91CXX_INTERRUPT_RX_OVRN_INT_M 0x1000 -#define LAN91CXX_INTERRUPT_ALLOC_INT_M 0x0800 -#define LAN91CXX_INTERRUPT_TX_EMPTY_INT_M 0x0400 -#define LAN91CXX_INTERRUPT_TX_INT_M 0x0200 -#define LAN91CXX_INTERRUPT_RCV_INT_M 0x0100 -#define LAN91CXX_INTERRUPT_TX_IDLE 0x0080 /* (91C96)*/ -#define LAN91CXX_INTERRUPT_ERCV_INT 0x0040 /* also ack*/ -#define LAN91CXX_INTERRUPT_EPH_INT 0x0020 -#define LAN91CXX_INTERRUPT_RX_OVRN_INT 0x0010 /* also ack*/ -#define LAN91CXX_INTERRUPT_ALLOC_INT 0x0008 -#define LAN91CXX_INTERRUPT_TX_EMPTY_INT 0x0004 /* also ack*/ -#define LAN91CXX_INTERRUPT_TX_INT 0x0002 /* also ack*/ -#define LAN91CXX_INTERRUPT_RCV_INT 0x0001 - -#define LAN91CXX_INTERRUPT_TX_SET 0x0006 /* TX_EMPTY + TX*/ -#define LAN91CXX_INTERRUPT_TX_SET_ACK 0x0004 /* TX_EMPTY and not plain TX*/ -#define LAN91CXX_INTERRUPT_TX_FIFO_ACK 0x0002 /* TX alone*/ -#define LAN91CXX_INTERRUPT_TX_SET_M 0x0600 /* TX_EMPTY + TX*/ - -#define LAN91CXX_CONTROL_RCV_BAD 0x4000 -#define LAN91CXX_CONTROL_AUTO_RELEASE 0x0800 -#define LAN91CXX_CONTROL_LE_ENABLE 0x0080 -#define LAN91CXX_CONTROL_CR_ENABLE 0x0040 -#define LAN91CXX_CONTROL_TE_ENABLE 0x0020 - -/* These are for setting the MAC address in the 91C96 serial EEPROM*/ -#define LAN91CXX_CONTROL_EEPROM_SELECT 0x0004 -#define LAN91CXX_CONTROL_RELOAD 0x0002 -#define LAN91CXX_CONTROL_STORE 0x0001 -#define LAN91CXX_CONTROL_EEPROM_BUSY 0x0003 -#define LAN91CXX_ESA_EEPROM_OFFSET 0x0020 - -#define LAN91CXX_STATUS_TX_UNRN 0x8000 -#define LAN91CXX_STATUS_LINK_OK 0x4000 -#define LAN91CXX_STATUS_CTR_ROL 0x1000 -#define LAN91CXX_STATUS_EXC_DEF 0x0800 -#define LAN91CXX_STATUS_LOST_CARR 0x0400 -#define LAN91CXX_STATUS_LATCOL 0x0200 -#define LAN91CXX_STATUS_WAKEUP 0x0100 -#define LAN91CXX_STATUS_TX_DEFR 0x0080 -#define LAN91CXX_STATUS_LTX_BRD 0x0040 -#define LAN91CXX_STATUS_SQET 0x0020 -#define LAN91CXX_STATUS_16COL 0x0010 -#define LAN91CXX_STATUS_LTX_MULT 0x0008 -#define LAN91CXX_STATUS_MUL_COL 0x0004 -#define LAN91CXX_STATUS_SNGL_COL 0x0002 -#define LAN91CXX_STATUS_TX_SUC 0x0001 - -#define LAN91CXX_MMU_COMMAND_BUSY 0x0001 - -#define LAN91CXX_MMU_noop 0x0000 -#define LAN91CXX_MMU_alloc_for_tx 0x0020 -#define LAN91CXX_MMU_reset_mmu 0x0040 -#define LAN91CXX_MMU_rem_rx_frame 0x0060 -#define LAN91CXX_MMU_rem_tx_frame 0x0070 /* (91C96) only when TX stopped*/ -#define LAN91CXX_MMU_remrel_rx_frame 0x0080 -#define LAN91CXX_MMU_rel_packet 0x00a0 -#define LAN91CXX_MMU_enq_packet 0x00c0 -#define LAN91CXX_MMU_reset_tx_fifo 0x00e0 - -#define LAN91CXX_CONTROLBYTE_CRC 0x1000 -#define LAN91CXX_CONTROLBYTE_ODD 0x2000 -#define LAN91CXX_CONTROLBYTE_RX 0x4000 - -#define LAN91CXX_RX_STATUS_ALIGNERR 0x8000 -#define LAN91CXX_RX_STATUS_BCAST 0x4000 -#define LAN91CXX_RX_STATUS_BADCRC 0x2000 -#define LAN91CXX_RX_STATUS_ODDFRM 0x1000 -#define LAN91CXX_RX_STATUS_TOOLONG 0x0800 -#define LAN91CXX_RX_STATUS_TOOSHORT 0x0400 -#define LAN91CXX_RX_STATUS_HASHVALMASK 0x007e /* MASK*/ -#define LAN91CXX_RX_STATUS_MCAST 0x0001 -#define LAN91CXX_RX_STATUS_BAD \ - (LAN91CXX_RX_STATUS_ALIGNERR | \ - LAN91CXX_RX_STATUS_BADCRC | \ - LAN91CXX_RX_STATUS_TOOLONG | \ - LAN91CXX_RX_STATUS_TOOSHORT) - -#define LAN91CXX_RX_STATUS_IS_ODD(__cpd,__stat) ((__stat) & LAN91CXX_RX_STATUS_ODDFRM) -#define LAN91CXX_CONTROLBYTE_IS_ODD(__cpd,__val) ((__val) & LAN91CXX_CONTROLBYTE_ODD) - -/* Attribute memory registers in PCMCIA mode*/ -#define LAN91CXX_ECOR 0x8000 -#define LAN91CXX_ECOR_RESET (1<<7) -#define LAN91CXX_ECOR_LEVIRQ (1<<6) -#define LAN91CXX_ECOR_ATTWR (1<<2) -#define LAN91CXX_ECOR_ENABLE (1<<0) - -#define LAN91CXX_ECSR 0x8002 -#define LAN91CXX_ECSR_IOIS8 (1<<5) -#define LAN91CXX_ECSR_PWRDWN (1<<2) -#define LAN91CXX_ECSR_INTR (1<<1) - -/* These are for manipulating the MII interface*/ -#define LAN91CXX_MGMT_MDO 0x0001 -#define LAN91CXX_MGMT_MDI 0x0002 -#define LAN91CXX_MGMT_MCLK 0x0004 -#define LAN91CXX_MGMT_MDOE 0x0008 - -/* Internal PHY registers (91c111)*/ -#define LAN91CXX_PHY_CTRL 0 -#define LAN91CXX_PHY_STAT 1 -#define LAN91CXX_PHY_ID1 2 -#define LAN91CXX_PHY_ID2 3 -#define LAN91CXX_PHY_AUTO_AD 4 -#define LAN91CXX_PHY_AUTO_CAP 5 -#define LAN91CXX_PHY_CONFIG1 16 -#define LAN91CXX_PHY_CONFIG2 17 -#define LAN91CXX_PHY_STATUS_OUT 18 -#define LAN91CXX_PHY_MASK 19 - -/* PHY control bits*/ -#define LAN91CXX_PHY_CTRL_COLTST (1 << 7) -#define LAN91CXX_PHY_CTRL_DPLX (1 << 8) -#define LAN91CXX_PHY_CTRL_ANEG_RST (1 << 9) -#define LAN91CXX_PHY_CTRL_MII_DIS (1 << 10) -#define LAN91CXX_PHY_CTRL_PDN (1 << 11) -#define LAN91CXX_PHY_CTRL_ANEG_EN (1 << 12) -#define LAN91CXX_PHY_CTRL_SPEED (1 << 13) -#define LAN91CXX_PHY_CTRL_LPBK (1 << 14) -#define LAN91CXX_PHY_CTRL_RST (1 << 15) - -/* PHY Configuration Register 1 */ -#define PHY_CFG1_LNKDIS 0x8000 /* 1=Rx Link Detect Function disabled */ -#define PHY_CFG1_XMTDIS 0x4000 /* 1=TP Transmitter Disabled */ -#define PHY_CFG1_XMTPDN 0x2000 /* 1=TP Transmitter Powered Down */ -#define PHY_CFG1_BYPSCR 0x0400 /* 1=Bypass scrambler/descrambler */ -#define PHY_CFG1_UNSCDS 0x0200 /* 1=Unscramble Idle Reception Disable */ -#define PHY_CFG1_EQLZR 0x0100 /* 1=Rx Equalizer Disabled */ -#define PHY_CFG1_CABLE 0x0080 /* 1=STP(150ohm), 0=UTP(100ohm) */ -#define PHY_CFG1_RLVL0 0x0040 /* 1=Rx Squelch level reduced by 4.5db */ -#define PHY_CFG1_TLVL_SHIFT 2 /* Transmit Output Level Adjust */ -#define PHY_CFG1_TLVL_MASK 0x003C -#define PHY_CFG1_TRF_MASK 0x0003 /* Transmitter Rise/Fall time */ - -/* PHY Configuration Register 2 */ -#define PHY_CFG2_REG 0x11 -#define PHY_CFG2_APOLDIS 0x0020 /* 1=Auto Polarity Correction disabled */ -#define PHY_CFG2_JABDIS 0x0010 /* 1=Jabber disabled */ -#define PHY_CFG2_MREG 0x0008 /* 1=Multiple register access (MII mgt) */ -#define PHY_CFG2_INTMDIO 0x0004 /* 1=Interrupt signaled with MDIO pulseo */ - -/* PHY Status Output (and Interrupt status) Register */ -#define PHY_INT_REG 0x12 /* Status Output (Interrupt Status) */ -#define PHY_INT_INT 0x8000 /* 1=bits have changed since last read */ -#define PHY_INT_LNKFAIL 0x4000 /* 1=Link Not detected */ -#define PHY_INT_LOSSSYNC 0x2000 /* 1=Descrambler has lost sync */ -#define PHY_INT_CWRD 0x1000 /* 1=Invalid 4B5B code detected on rx */ -#define PHY_INT_SSD 0x0800 /* 1=No Start Of Stream detected on rx */ -#define PHY_INT_ESD 0x0400 /* 1=No End Of Stream detected on rx */ -#define PHY_INT_RPOL 0x0200 /* 1=Reverse Polarity detected */ -#define PHY_INT_JAB 0x0100 /* 1=Jabber detected */ -#define PHY_INT_SPDDET 0x0080 /* 1=100Base-TX mode, 0=10Base-T mode */ -#define PHY_INT_DPLXDET 0x0040 /* 1=Device in Full Duplex */ - -/* PHY Interrupt/Status Mask Register */ -#define PHY_MASK_REG 0x13 /* Interrupt Mask */ - -#define LAN91CXX_RPCR_LEDA_LINK (0 << 2) -#define LAN91CXX_RPCR_LEDA_TXRX (4 << 2) -#define LAN91CXX_RPCR_LEDA_RX (6 << 2) -#define LAN91CXX_RPCR_LEDA_TX (7 << 2) -#define LAN91CXX_RPCR_LEDB_LINK (0 << 5) -#define LAN91CXX_RPCR_LEDB_TXRX (4 << 5) -#define LAN91CXX_RPCR_LEDB_RX (6 << 5) -#define LAN91CXX_RPCR_LEDB_TX (7 << 5) -#define LAN91CXX_RPCR_ANEG (1 << 11) -#define LAN91CXX_RPCR_DPLX (1 << 12) -#define LAN91CXX_RPCR_SPEED (1 << 13) - -/* PHY Control Register */ -#define PHY_CNTL_REG 0x00 -#define PHY_CNTL_RST 0x8000 /* 1=PHY Reset */ -#define PHY_CNTL_LPBK 0x4000 /* 1=PHY Loopback */ -#define PHY_CNTL_SPEED 0x2000 /* 1=100Mbps, 0=10Mpbs */ -#define PHY_CNTL_ANEG_EN 0x1000 /* 1=Enable Auto negotiation */ -#define PHY_CNTL_PDN 0x0800 /* 1=PHY Power Down mode */ -#define PHY_CNTL_MII_DIS 0x0400 /* 1=MII 4 bit interface disabled */ -#define PHY_CNTL_ANEG_RST 0x0200 /* 1=Reset Auto negotiate */ -#define PHY_CNTL_DPLX 0x0100 /* 1=Full Duplex, 0=Half Duplex */ -#define PHY_CNTL_COLTST 0x0080 /* 1= MII Colision Test */ - -/* PHY Status Register */ -#define PHY_STAT_REG 0x01 -#define PHY_STAT_CAP_T4 0x8000 /* 1=100Base-T4 capable */ -#define PHY_STAT_CAP_TXF 0x4000 /* 1=100Base-X full duplex capable */ -#define PHY_STAT_CAP_TXH 0x2000 /* 1=100Base-X half duplex capable */ -#define PHY_STAT_CAP_TF 0x1000 /* 1=10Mbps full duplex capable */ -#define PHY_STAT_CAP_TH 0x0800 /* 1=10Mbps half duplex capable */ -#define PHY_STAT_CAP_SUPR 0x0040 /* 1=recv mgmt frames with not preamble */ -#define PHY_STAT_ANEG_ACK 0x0020 /* 1=ANEG has completed */ -#define PHY_STAT_REM_FLT 0x0010 /* 1=Remote Fault detected */ -#define PHY_STAT_CAP_ANEG 0x0008 /* 1=Auto negotiate capable */ -#define PHY_STAT_LINK 0x0004 /* 1=valid link */ -#define PHY_STAT_JAB 0x0002 /* 1=10Mbps jabber condition */ -#define PHY_STAT_EXREG 0x0001 /* 1=extended registers implemented */ -#define PHY_STAT_RESERVED 0x0780 /* Reserved bits mask. */ - -/* PHY Identifier Registers */ -#define PHY_ID1_REG 0x02 /* PHY Identifier 1 */ -#define PHY_ID2_REG 0x03 /* PHY Identifier 2 */ - -/* PHY Auto-Negotiation Advertisement Register */ -#define PHY_AD_REG 0x04 -#define PHY_AD_NP 0x8000 /* 1=PHY requests exchange of Next Page */ -#define PHY_AD_ACK 0x4000 /* 1=got link code word from remote */ -#define PHY_AD_RF 0x2000 /* 1=advertise remote fault */ -#define PHY_AD_T4 0x0200 /* 1=PHY is capable of 100Base-T4 */ -#define PHY_AD_TX_FDX 0x0100 /* 1=PHY is capable of 100Base-TX FDPLX */ -#define PHY_AD_TX_HDX 0x0080 /* 1=PHY is capable of 100Base-TX HDPLX */ -#define PHY_AD_10_FDX 0x0040 /* 1=PHY is capable of 10Base-T FDPLX */ -#define PHY_AD_10_HDX 0x0020 /* 1=PHY is capable of 10Base-T HDPLX */ -#define PHY_AD_CSMA 0x0001 /* 1=PHY is capable of 802.3 CMSA */ - - -static int debugflag_out = 0; - -#define dbc_printf(lvl,format, args...) do { \ - if (!debugflag_out) { \ - if (lvl & DEBUG) { \ - printk(format,##args); \ - } \ - } \ -} while(0) - -#define db64_printf(format, args...) dbc_printf(64,format,##args); -#define db16_printf(format, args...) dbc_printf(16,format,##args); -#define db9_printf(format, args...) dbc_printf(9,format,##args); -#define db4_printf(format, args...) dbc_printf(4,format,##args); -#define db2_printf(format, args...) dbc_printf(2,format,##args); -#define db1_printf(format, args...) dbc_printf(1,format,##args); -#define db_printf(format, args...) dbc_printf(0xffff,format,##args); - -#if DEBUG & 1 -#define DEBUG_FUNCTION() do { db_printf("# %s\n", __FUNCTION__); } while (0) -#else -#define DEBUG_FUNCTION() do {} while(0) -#endif - - -/* ------------------------------------------------------------------------*/ - -struct smsc_lan91cxx_stats { - unsigned int tx_good ; - unsigned int tx_max_collisions ; - unsigned int tx_late_collisions ; - unsigned int tx_underrun ; - unsigned int tx_carrier_loss ; - unsigned int tx_deferred ; - unsigned int tx_sqetesterrors ; - unsigned int tx_single_collisions; - unsigned int tx_mult_collisions ; - unsigned int tx_total_collisions ; - unsigned int rx_good ; - unsigned int rx_crc_errors ; - unsigned int rx_align_errors ; - unsigned int rx_resource_errors ; - unsigned int rx_overrun_errors ; - unsigned int rx_collisions ; - unsigned int rx_short_frames ; - unsigned int rx_too_long_frames ; - unsigned int rx_symbol_errors ; - unsigned int interrupts ; - unsigned int rx_count ; - unsigned int rx_deliver ; - unsigned int rx_resource ; - unsigned int rx_restart ; - unsigned int tx_count ; - unsigned int tx_complete ; - unsigned int tx_dropped ; -}; -#define INCR_STAT(c,n) (((c)->stats.n)++) - -struct lan91cxx_priv_data; - -typedef struct lan91cxx_priv_data { - - /* frontend */ - struct arpcom arpcom; - rtems_id rxDaemonTid; - rtems_id txDaemonTid; - - scmv91111_configuration_t config; - - /* backend */ - int rpc_cur_mode; - int autoneg_active; - int phyaddr; - unsigned int lastPhy18; - - int txbusy; /* A packet has been sent*/ - unsigned long txkey; /* Used to ack when packet sent*/ - unsigned short* base; /* Base I/O address of controller*/ - /* (as it comes out of reset)*/ - int interrupt; /* Interrupt vector used by controller*/ - unsigned char enaddr[6]; /* Controller ESA*/ - /* Function to configure the ESA - may fetch ESA from EPROM or */ - /* RedBoot config option. Use of the 'config_enaddr()' function*/ - /* is depreciated in favor of the 'provide_esa()' function and*/ - /* 'hardwired_esa' boolean*/ - void (*config_enaddr)(struct lan91cxx_priv_data* cpd); - int hardwired_esa; - int txpacket; - int rxpacket; - int within_send; - int c111_reva; /* true if this is a revA LAN91C111*/ - struct smsc_lan91cxx_stats stats; -} lan91cxx_priv_data; - -/* ------------------------------------------------------------------------*/ - -#ifdef LAN91CXX_32BIT_RX -typedef unsigned int rxd_t; -#else -typedef unsigned short rxd_t; -#endif - -typedef struct _debug_regs_pair { - int reg; char *name; struct _debug_regs_pair *bits; -} debug_regs_pair; - -static debug_regs_pair debug_regs[] = { - {LAN91CXX_TCR , "LAN91CXX_TCR" ,0}, - {LAN91CXX_EPH_STATUS , "LAN91CXX_EPH_STATUS",0}, - {LAN91CXX_RCR , "LAN91CXX_RCR" ,0}, - {LAN91CXX_COUNTER , "LAN91CXX_COUNTER" ,0}, - {LAN91CXX_MIR , "LAN91CXX_MIR" ,0}, - {LAN91CXX_MCR , "LAN91CXX_MCR" ,0}, - {LAN91CXX_RPCR , "LAN91CXX_RPCR" ,0}, - {LAN91CXX_RESERVED_0 , "LAN91CXX_RESERVED_0",0}, - {LAN91CXX_BS , "LAN91CXX_BS" ,0}, - {LAN91CXX_CONFIG , "LAN91CXX_CONFIG" ,0}, - {LAN91CXX_BASE_REG , "LAN91CXX_BASE_REG" ,0}, - {LAN91CXX_IA01 , "LAN91CXX_IA01" ,0}, - {LAN91CXX_IA23 , "LAN91CXX_IA23" ,0}, - {LAN91CXX_IA45 , "LAN91CXX_IA45" ,0}, - {LAN91CXX_GENERAL , "LAN91CXX_GENERAL" ,0}, - {LAN91CXX_CONTROL , "LAN91CXX_CONTROL" ,0}, - {LAN91CXX_BS2 , "LAN91CXX_BS2" ,0}, - {LAN91CXX_MMU_COMMAND, "LAN91CXX_MMU_COMMAND",0}, - {LAN91CXX_PNR , "LAN91CXX_PNR" ,0}, - {LAN91CXX_FIFO_PORTS , "LAN91CXX_FIFO_PORTS" ,0}, - {LAN91CXX_POINTER , "LAN91CXX_POINTER" ,0}, - {LAN91CXX_DATA_HIGH , "LAN91CXX_DATA_HIGH" ,0}, - {LAN91CXX_DATA , "LAN91CXX_DATA" ,0}, - {LAN91CXX_INTERRUPT , "LAN91CXX_INTERRUPT" ,0}, - {LAN91CXX_BS3 , "LAN91CXX_BS3" ,0}, - {LAN91CXX_MT01 , "LAN91CXX_MT01" ,0}, - {LAN91CXX_MT23 , "LAN91CXX_MT23" ,0}, - {LAN91CXX_MT45 , "LAN91CXX_MT45" ,0}, - {LAN91CXX_MT67 , "LAN91CXX_MT67" ,0}, -/*{LAN91CXX_MGMT , "LAN91CXX_MGMT" ,0}, */ - {LAN91CXX_REVISION , "LAN91CXX_REVISION" ,0}, - {LAN91CXX_ERCV , "LAN91CXX_ERCV" ,0}, - {LAN91CXX_BS4 , "LAN91CXX_BS4" ,0}, - - - - {-1,0} -}; - -static char *dbg_prefix = ""; - -#ifndef SMSC_PLATFORM_DEFINED_GET_REG -static __inline__ unsigned short -get_reg(struct lan91cxx_priv_data *cpd, int regno) -{ - unsigned short val; debug_regs_pair *dbg = debug_regs; int c; - uint32_t Irql; - - /*rtems_interrupt_disable(Irql);*/ - - HAL_WRITE_UINT16(cpd->base+(LAN91CXX_BS), CYG_CPU_TO_LE16(regno>>3)); - HAL_READ_UINT16(cpd->base+((regno&0x7)), val); - val = CYG_LE16_TO_CPU(val); - - /*rtems_interrupt_enable(Irql);*/ - -#if DEBUG & 32 - while ((c = dbg->reg) != -1) { - if (c == regno) { - db_printf("%sread reg [%d:%x] -> 0x%04x (%-20s)\n", dbg_prefix, regno>>3,(regno&0x7)*2, val, dbg->name); - break; - } - dbg++; - } -#else - db2_printf("%sread reg %d:%x -> 0x%04x\n", dbg_prefix, regno>>3,(regno&0x7)*2, val); -#endif - - return val; -} -#endif /* SMSC_PLATFORM_DEFINED_GET_REG*/ - -#ifndef SMSC_PLATFORM_DEFINED_PUT_REG -static __inline__ void -put_reg(struct lan91cxx_priv_data *cpd, int regno, unsigned short val) -{ - debug_regs_pair *dbg = debug_regs; int c; - uint32_t Irql; - -#if DEBUG & 32 - while ((c = dbg->reg) != -1) { - if (c == regno) { - db_printf("%swrite reg [%d:%x] <- 0x%04x (%-20s)\n", dbg_prefix, regno>>3, (regno&0x07)*2, val, dbg->name); - break; - } - dbg++; - } -#else - db2_printf("%swrite reg %d:%x <- 0x%04x\n", dbg_prefix, regno>>3,(regno&0x7)*2, val); -#endif - - /*rtems_interrupt_disable(Irql);*/ - - HAL_WRITE_UINT16(cpd->base+(LAN91CXX_BS), CYG_CPU_TO_LE16(regno>>3)); - HAL_WRITE_UINT16(cpd->base+((regno&0x7)), CYG_CPU_TO_LE16(val)); - - /*rtems_interrupt_enable(Irql);*/ - -} -#endif /* SMSC_PLATFORM_DEFINED_PUT_REG*/ - -#ifndef SMSC_PLATFORM_DEFINED_PUT_DATA -/* ------------------------------------------------------------------------*/ -/* Assumes bank2 has been selected*/ -static __inline__ void -put_data(struct lan91cxx_priv_data *cpd, unsigned short val) -{ - db2_printf("%s[wdata] <- 0x%04x\n", dbg_prefix, val); - - HAL_WRITE_UINT16(cpd->base+((LAN91CXX_DATA & 0x7)), val); - -} - -/* Assumes bank2 has been selected*/ -static __inline__ void -put_data8(struct lan91cxx_priv_data *cpd, unsigned char val) -{ - db2_printf("%s[bdata] <- 0x%02x\n", dbg_prefix, val); - - HAL_WRITE_UINT8(((unsigned char *)(cpd->base+((LAN91CXX_DATA & 0x7))))+1, val); - -} - -#endif /* SMSC_PLATFORM_DEFINED_PUT_DATA*/ - -#ifndef SMSC_PLATFORM_DEFINED_GET_DATA -/* Assumes bank2 has been selected*/ -static __inline__ rxd_t -get_data(struct lan91cxx_priv_data *cpd) -{ - rxd_t val; - -#ifdef LAN91CXX_32BIT_RX - HAL_READ_UINT32(cpd->base+((LAN91CXX_DATA_HIGH & 0x7)), val); -#else - HAL_READ_UINT16(cpd->base+((LAN91CXX_DATA & 0x7)), val); -#endif - - db2_printf("%s[rdata] -> 0x%08x\n", dbg_prefix, val); - return val; -} -#endif /* SMSC_PLATFORM_DEFINED_GET_DATA*/ - -/* ------------------------------------------------------------------------*/ -/* Read the bank register (this one is bank-independent)*/ -#ifndef SMSC_PLATFORM_DEFINED_GET_BANKSEL -static __inline__ unsigned short -get_banksel(struct lan91cxx_priv_data *cpd) -{ - unsigned short val; - - HAL_READ_UINT16(cpd->base+(LAN91CXX_BS), val); - val = CYG_LE16_TO_CPU(val); - db2_printf("read bank sel val 0x%04x\n", val); - return val; -} -#endif - - - - - -#endif /* _SMC_91111_H_ */ - - |