diff options
Diffstat (limited to 'bsps/arm/stm32h7/hal/stm32h7xx_ll_usart.c')
-rw-r--r-- | bsps/arm/stm32h7/hal/stm32h7xx_ll_usart.c | 115 |
1 files changed, 57 insertions, 58 deletions
diff --git a/bsps/arm/stm32h7/hal/stm32h7xx_ll_usart.c b/bsps/arm/stm32h7/hal/stm32h7xx_ll_usart.c index 20766553d0..a38b4d59ab 100644 --- a/bsps/arm/stm32h7/hal/stm32h7xx_ll_usart.c +++ b/bsps/arm/stm32h7/hal/stm32h7xx_ll_usart.c @@ -6,13 +6,12 @@ ****************************************************************************** * @attention * - * <h2><center>© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.</center></h2> + * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * - * This software component is licensed by ST under BSD 3-Clause license, - * the "License"; You may not use this file except in compliance with the - * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ @@ -32,7 +31,8 @@ * @{ */ -#if defined (USART1) || defined (USART2) || defined (USART3) || defined (USART6) || defined (UART4) || defined (UART5) || defined (UART7) || defined (UART8) || defined (UART9) || defined (USART10) +#if defined(USART1) || defined(USART2) || defined(USART3) || defined(USART6) \ + || defined(UART4) || defined(UART5) || defined(UART7) || defined(UART8) || defined(UART9) || defined(USART10) /** @addtogroup USART_LL * @{ @@ -41,6 +41,17 @@ /* Private types -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private constants ---------------------------------------------------------*/ +/** @addtogroup USART_LL_Private_Constants + * @{ + */ + +/* Definition of default baudrate value used for USART initialisation */ +#define USART_DEFAULT_BAUDRATE (9600U) + +/** + * @} + */ + /* Private macros ------------------------------------------------------------*/ /** @addtogroup USART_LL_Private_Macros * @{ @@ -66,9 +77,6 @@ /* __VALUE__ In case of oversampling by 16 and 8, BRR content must be greater than or equal to 16d. */ #define IS_LL_USART_BRR_MIN(__VALUE__) ((__VALUE__) >= 16U) -/* __VALUE__ BRR content must be lower than or equal to 0xFFFF. */ -#define IS_LL_USART_BRR_MAX(__VALUE__) ((__VALUE__) <= 0x0000FFFFU) - #define IS_LL_USART_DIRECTION(__VALUE__) (((__VALUE__) == LL_USART_DIRECTION_NONE) \ || ((__VALUE__) == LL_USART_DIRECTION_RX) \ || ((__VALUE__) == LL_USART_DIRECTION_TX) \ @@ -129,7 +137,7 @@ * - SUCCESS: USART registers are de-initialized * - ERROR: USART registers are not de-initialized */ -ErrorStatus LL_USART_DeInit(USART_TypeDef *USARTx) +ErrorStatus LL_USART_DeInit(const USART_TypeDef *USARTx) { ErrorStatus status = SUCCESS; @@ -231,8 +239,9 @@ ErrorStatus LL_USART_DeInit(USART_TypeDef *USARTx) /** * @brief Initialize USART registers according to the specified * parameters in USART_InitStruct. - * @note As some bits in USART configuration registers can only be written when the USART is disabled (USART_CR1_UE bit =0), - * USART Peripheral should be in disabled state prior calling this function. Otherwise, ERROR result will be returned. + * @note As some bits in USART configuration registers can only be written when + * the USART is disabled (USART_CR1_UE bit =0), USART Peripheral should be in disabled state prior calling + * this function. Otherwise, ERROR result will be returned. * @note Baud rate value stored in USART_InitStruct BaudRate field, should be valid (different from 0). * @param USARTx USART Instance * @param USART_InitStruct pointer to a LL_USART_InitTypeDef structure @@ -241,7 +250,7 @@ ErrorStatus LL_USART_DeInit(USART_TypeDef *USARTx) * - SUCCESS: USART registers are initialized according to USART_InitStruct content * - ERROR: Problem occurred during USART Registers initialization */ -ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, LL_USART_InitTypeDef *USART_InitStruct) +ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, const LL_USART_InitTypeDef *USART_InitStruct) { ErrorStatus status = ERROR; uint32_t periphclk = LL_RCC_PERIPH_FREQUENCY_NO; @@ -283,7 +292,8 @@ ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, LL_USART_InitTypeDef *USART_Ini /*---------------------------- USART CR3 Configuration --------------------- * Configure USARTx CR3 (Hardware Flow Control) with parameters: - * - HardwareFlowControl: USART_CR3_RTSE, USART_CR3_CTSE bits according to USART_InitStruct->HardwareFlowControl value. + * - HardwareFlowControl: USART_CR3_RTSE, USART_CR3_CTSE bits according to + * USART_InitStruct->HardwareFlowControl value. */ LL_USART_SetHWFlowCtrl(USARTx, USART_InitStruct->HardwareFlowControl); @@ -356,9 +366,6 @@ ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, LL_USART_InitTypeDef *USART_Ini /* Check BRR is greater than or equal to 16d */ assert_param(IS_LL_USART_BRR_MIN(USARTx->BRR)); - - /* Check BRR is lower than or equal to 0xFFFF */ - assert_param(IS_LL_USART_BRR_MAX(USARTx->BRR)); } /*---------------------------- USART PRESC Configuration ----------------------- @@ -383,7 +390,7 @@ void LL_USART_StructInit(LL_USART_InitTypeDef *USART_InitStruct) { /* Set USART_InitStruct fields to default values */ USART_InitStruct->PrescalerValue = LL_USART_PRESCALER_DIV1; - USART_InitStruct->BaudRate = 9600U; + USART_InitStruct->BaudRate = USART_DEFAULT_BAUDRATE; USART_InitStruct->DataWidth = LL_USART_DATAWIDTH_8B; USART_InitStruct->StopBits = LL_USART_STOPBITS_1; USART_InitStruct->Parity = LL_USART_PARITY_NONE ; @@ -395,16 +402,18 @@ void LL_USART_StructInit(LL_USART_InitTypeDef *USART_InitStruct) /** * @brief Initialize USART Clock related settings according to the * specified parameters in the USART_ClockInitStruct. - * @note As some bits in USART configuration registers can only be written when the USART is disabled (USART_CR1_UE bit =0), - * USART Peripheral should be in disabled state prior calling this function. Otherwise, ERROR result will be returned. + * @note As some bits in USART configuration registers can only be written when + * the USART is disabled (USART_CR1_UE bit =0), USART Peripheral should be in disabled state prior calling + * this function. Otherwise, ERROR result will be returned. * @param USARTx USART Instance * @param USART_ClockInitStruct pointer to a @ref LL_USART_ClockInitTypeDef structure * that contains the Clock configuration information for the specified USART peripheral. * @retval An ErrorStatus enumeration value: - * - SUCCESS: USART registers related to Clock settings are initialized according to USART_ClockInitStruct content + * - SUCCESS: USART registers related to Clock settings are initialized according + * to USART_ClockInitStruct content * - ERROR: Problem occurred during USART Registers initialization */ -ErrorStatus LL_USART_ClockInit(USART_TypeDef *USARTx, LL_USART_ClockInitTypeDef *USART_ClockInitStruct) +ErrorStatus LL_USART_ClockInit(USART_TypeDef *USARTx, const LL_USART_ClockInitTypeDef *USART_ClockInitStruct) { ErrorStatus status = SUCCESS; @@ -416,37 +425,25 @@ ErrorStatus LL_USART_ClockInit(USART_TypeDef *USARTx, LL_USART_ClockInitTypeDef CRx registers */ if (LL_USART_IsEnabled(USARTx) == 0U) { - /*---------------------------- USART CR2 Configuration -----------------------*/ - /* If Clock signal has to be output */ - if (USART_ClockInitStruct->ClockOutput == LL_USART_CLOCK_DISABLE) - { - /* Deactivate Clock signal delivery : - * - Disable Clock Output: USART_CR2_CLKEN cleared - */ - LL_USART_DisableSCLKOutput(USARTx); - } - else - { - /* Ensure USART instance is USART capable */ - assert_param(IS_USART_INSTANCE(USARTx)); - - /* Check clock related parameters */ - assert_param(IS_LL_USART_CLOCKPOLARITY(USART_ClockInitStruct->ClockPolarity)); - assert_param(IS_LL_USART_CLOCKPHASE(USART_ClockInitStruct->ClockPhase)); - assert_param(IS_LL_USART_LASTBITCLKOUTPUT(USART_ClockInitStruct->LastBitClockPulse)); - - /*---------------------------- USART CR2 Configuration ----------------------- - * Configure USARTx CR2 (Clock signal related bits) with parameters: - * - Enable Clock Output: USART_CR2_CLKEN set - * - Clock Polarity: USART_CR2_CPOL bit according to USART_ClockInitStruct->ClockPolarity value - * - Clock Phase: USART_CR2_CPHA bit according to USART_ClockInitStruct->ClockPhase value - * - Last Bit Clock Pulse Output: USART_CR2_LBCL bit according to USART_ClockInitStruct->LastBitClockPulse value. - */ - MODIFY_REG(USARTx->CR2, - USART_CR2_CLKEN | USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL, - USART_CR2_CLKEN | USART_ClockInitStruct->ClockPolarity | - USART_ClockInitStruct->ClockPhase | USART_ClockInitStruct->LastBitClockPulse); - } + /* Ensure USART instance is USART capable */ + assert_param(IS_USART_INSTANCE(USARTx)); + + /* Check clock related parameters */ + assert_param(IS_LL_USART_CLOCKPOLARITY(USART_ClockInitStruct->ClockPolarity)); + assert_param(IS_LL_USART_CLOCKPHASE(USART_ClockInitStruct->ClockPhase)); + assert_param(IS_LL_USART_LASTBITCLKOUTPUT(USART_ClockInitStruct->LastBitClockPulse)); + + /*---------------------------- USART CR2 Configuration ----------------------- + * Configure USARTx CR2 (Clock signal related bits) with parameters: + * - Clock Output: USART_CR2_CLKEN bit according to USART_ClockInitStruct->ClockOutput value + * - Clock Polarity: USART_CR2_CPOL bit according to USART_ClockInitStruct->ClockPolarity value + * - Clock Phase: USART_CR2_CPHA bit according to USART_ClockInitStruct->ClockPhase value + * - Last Bit Clock Pulse Output: USART_CR2_LBCL bit according to USART_ClockInitStruct->LastBitClockPulse value. + */ + MODIFY_REG(USARTx->CR2, + USART_CR2_CLKEN | USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL, + USART_ClockInitStruct->ClockOutput | USART_ClockInitStruct->ClockPolarity | + USART_ClockInitStruct->ClockPhase | USART_ClockInitStruct->LastBitClockPulse); } /* Else (USART not in Disabled state => return ERROR */ else @@ -467,9 +464,12 @@ void LL_USART_ClockStructInit(LL_USART_ClockInitTypeDef *USART_ClockInitStruct) { /* Set LL_USART_ClockInitStruct fields with default values */ USART_ClockInitStruct->ClockOutput = LL_USART_CLOCK_DISABLE; - USART_ClockInitStruct->ClockPolarity = LL_USART_POLARITY_LOW; /* Not relevant when ClockOutput = LL_USART_CLOCK_DISABLE */ - USART_ClockInitStruct->ClockPhase = LL_USART_PHASE_1EDGE; /* Not relevant when ClockOutput = LL_USART_CLOCK_DISABLE */ - USART_ClockInitStruct->LastBitClockPulse = LL_USART_LASTCLKPULSE_NO_OUTPUT; /* Not relevant when ClockOutput = LL_USART_CLOCK_DISABLE */ + USART_ClockInitStruct->ClockPolarity = LL_USART_POLARITY_LOW; /* Not relevant when ClockOutput = + LL_USART_CLOCK_DISABLE */ + USART_ClockInitStruct->ClockPhase = LL_USART_PHASE_1EDGE; /* Not relevant when ClockOutput = + LL_USART_CLOCK_DISABLE */ + USART_ClockInitStruct->LastBitClockPulse = LL_USART_LASTCLKPULSE_NO_OUTPUT; /* Not relevant when ClockOutput = + LL_USART_CLOCK_DISABLE */ } /** @@ -492,5 +492,4 @@ void LL_USART_ClockStructInit(LL_USART_ClockInitTypeDef *USART_ClockInitStruct) #endif /* USE_FULL_LL_DRIVER */ -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |