diff options
Diffstat (limited to 'bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c')
-rw-r--r-- | bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c | 968 |
1 files changed, 796 insertions, 172 deletions
diff --git a/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c b/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c index 37fa2ed013..4c36d9057a 100644 --- a/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c +++ b/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c @@ -11,6 +11,17 @@ * + Time Master and Slave synchronization configuration * + Time Output Compare/PWM Channel Configuration (for channels 5 and 6) * + Timer remapping capabilities configuration + ****************************************************************************** + * @attention + * + * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** @verbatim ============================================================================== ##### TIMER Extended features ##### @@ -55,24 +66,16 @@ the commutation event). (#) Activate the TIM peripheral using one of the start functions: - (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), HAL_TIMEx_OC_Start_IT() - (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), HAL_TIMEx_PWMN_Start_IT() + (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), + HAL_TIMEx_OCN_Start_IT() + (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), + HAL_TIMEx_PWMN_Start_IT() (++) Complementary One-pulse mode output : HAL_TIMEx_OnePulseN_Start(), HAL_TIMEx_OnePulseN_Start_IT() - (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), HAL_TIMEx_HallSensor_Start_IT(). + (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), + HAL_TIMEx_HallSensor_Start_IT(). @endverbatim ****************************************************************************** - * @attention - * - * <h2><center>© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.</center></h2> - * - * This software component is licensed by ST under BSD 3-Clause license, - * the "License"; You may not use this file except in compliance with the - * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause - * - ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ @@ -92,9 +95,25 @@ /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ -/* Private macro -------------------------------------------------------------*/ +#if defined(TIM_BDTR_BKBID) +/* Private constants ---------------------------------------------------------*/ +/** @defgroup TIMEx_Private_Constants TIM Extended Private Constants + * @ingroup RTEMSBSPsARMSTM32H7 + * @{ + */ +/* Timeout for break input rearm */ +#define TIM_BREAKINPUT_REARM_TIMEOUT 5UL /* 5 milliseconds */ +/** + * @} + */ +/* End of private constants --------------------------------------------------*/ + +#endif /* TIM_BDTR_BKBID */ +/* Private macros ------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ +static void TIM_DMADelayPulseNCplt(DMA_HandleTypeDef *hdma); +static void TIM_DMAErrorCCxN(DMA_HandleTypeDef *hdma); static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t ChannelNState); /* Exported functions --------------------------------------------------------*/ @@ -127,11 +146,14 @@ static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t Cha */ /** * @brief Initializes the TIM Hall Sensor Interface and initialize the associated handle. + * @note When the timer instance is initialized in Hall Sensor Interface mode, + * timer channels 1 and channel 2 are reserved and cannot be used for + * other purpose. * @param htim TIM Hall Sensor Interface handle * @param sConfig TIM Hall Sensor configuration structure * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef *sConfig) +HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, const TIM_HallSensor_InitTypeDef *sConfig) { TIM_OC_InitTypeDef OC_Config; @@ -147,6 +169,7 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSen assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity)); + assert_param(IS_TIM_PERIOD(htim, htim->Init.Period)); assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter)); @@ -212,6 +235,15 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSen htim->Instance->CR2 &= ~TIM_CR2_MMS; htim->Instance->CR2 |= TIM_TRGO_OC2REF; + /* Initialize the DMA burst operation state */ + htim->DMABurstState = HAL_DMA_BURST_STATE_READY; + + /* Initialize the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + /* Initialize the TIM state*/ htim->State = HAL_TIM_STATE_READY; @@ -245,6 +277,15 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim) HAL_TIMEx_HallSensor_MspDeInit(htim); #endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + /* Change the DMA burst operation state */ + htim->DMABurstState = HAL_DMA_BURST_STATE_RESET; + + /* Change the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_RESET); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_RESET); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_RESET); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_RESET); + /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; @@ -292,17 +333,44 @@ __weak void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim) HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim) { uint32_t tmpsmcr; + HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef channel_2_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_2); + HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef complementary_channel_2_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_2); /* Check the parameters */ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + /* Check the TIM channels state */ + if ((channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (channel_2_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_2_state != HAL_TIM_CHANNEL_STATE_READY)) + { + return HAL_ERROR; + } + + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + /* Enable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, + TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else { __HAL_TIM_ENABLE(htim); } @@ -322,12 +390,19 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim) assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1, 2 and 3 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, + TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -340,20 +415,47 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim) HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim) { uint32_t tmpsmcr; + HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef channel_2_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_2); + HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef complementary_channel_2_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_2); /* Check the parameters */ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); + /* Check the TIM channels state */ + if ((channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (channel_2_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_2_state != HAL_TIM_CHANNEL_STATE_READY)) + { + return HAL_ERROR; + } + + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + /* Enable the capture compare Interrupts 1 event */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); /* Enable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, + TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else { __HAL_TIM_ENABLE(htim); } @@ -373,7 +475,8 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim) assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); /* Disable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, + TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts event */ @@ -382,6 +485,12 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -396,31 +505,39 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim) HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length) { uint32_t tmpsmcr; + HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1); /* Check the parameters */ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); - if (htim->State == HAL_TIM_STATE_BUSY) + /* Set the TIM channel state */ + if ((channel_1_state == HAL_TIM_CHANNEL_STATE_BUSY) + || (complementary_channel_1_state == HAL_TIM_CHANNEL_STATE_BUSY)) { return HAL_BUSY; } - else if (htim->State == HAL_TIM_STATE_READY) + else if ((channel_1_state == HAL_TIM_CHANNEL_STATE_READY) + && (complementary_channel_1_state == HAL_TIM_CHANNEL_STATE_READY)) { - if (((uint32_t)pData == 0U) && (Length > 0U)) + if ((pData == NULL) || (Length == 0U)) { return HAL_ERROR; } else { - htim->State = HAL_TIM_STATE_BUSY; + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); } } else { - /* nothing to do */ + return HAL_ERROR; } + /* Enable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, + TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); /* Set the DMA Input Capture 1 Callbacks */ @@ -432,14 +549,22 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32 /* Enable the DMA stream for Capture 1*/ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the capture compare 1 Interrupt */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else { __HAL_TIM_ENABLE(htim); } @@ -459,7 +584,8 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim) assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance)); /* Disable the Input Capture channel 1 - (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */ + (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, + TIM_CHANNEL_2 and TIM_CHANNEL_3) */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); @@ -467,9 +593,14 @@ HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim) __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]); + /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM channel state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -517,6 +648,15 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel) /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Check the TIM complementary channel state */ + if (TIM_CHANNEL_N_STATE_GET(htim, Channel) != HAL_TIM_CHANNEL_STATE_READY) + { + return HAL_ERROR; + } + + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_BUSY); + /* Enable the Capture compare channel N */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); @@ -524,8 +664,15 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel) __HAL_TIM_MOE_ENABLE(htim); /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else { __HAL_TIM_ENABLE(htim); } @@ -559,6 +706,9 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -576,11 +726,21 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) */ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmpsmcr; /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Check the TIM complementary channel state */ + if (TIM_CHANNEL_N_STATE_GET(htim, Channel) != HAL_TIM_CHANNEL_STATE_READY) + { + return HAL_ERROR; + } + + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_BUSY); + switch (Channel) { case TIM_CHANNEL_1: @@ -606,27 +766,38 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Chann default: + status = HAL_ERROR; break; } - /* Enable the TIM Break interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); + if (status == HAL_OK) + { + /* Enable the TIM Break interrupt */ + __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); - /* Enable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the Capture compare channel N */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); + /* Enable the Main Output */ + __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else + { + __HAL_TIM_ENABLE(htim); + } } /* Return function status */ - return HAL_OK; + return status; } /** @@ -642,7 +813,9 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Chann */ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmpccer; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -670,27 +843,34 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channe } default: + status = HAL_ERROR; break; } - /* Disable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the TIM Break interrupt (only if no more channel is active) */ - tmpccer = htim->Instance->CCER; - if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) + if (status == HAL_OK) { - __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); - } + /* Disable the Capture compare channel N */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); + /* Disable the TIM Break interrupt (only if no more channel is active) */ + tmpccer = htim->Instance->CCER; + if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) + { + __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); + } - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); + /* Disable the Main Output */ + __HAL_TIM_MOE_DISABLE(htim); + + /* Disable the Peripheral */ + __HAL_TIM_DISABLE(htim); + + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_READY); + } /* Return function status */ - return HAL_OK; + return status; } /** @@ -706,31 +886,34 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channe * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) +HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, const uint32_t *pData, + uint16_t Length) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmpsmcr; /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - if (htim->State == HAL_TIM_STATE_BUSY) + /* Set the TIM complementary channel state */ + if (TIM_CHANNEL_N_STATE_GET(htim, Channel) == HAL_TIM_CHANNEL_STATE_BUSY) { return HAL_BUSY; } - else if (htim->State == HAL_TIM_STATE_READY) + else if (TIM_CHANNEL_N_STATE_GET(htim, Channel) == HAL_TIM_CHANNEL_STATE_READY) { - if (((uint32_t)pData == 0U) && (Length > 0U)) + if ((pData == NULL) || (Length == 0U)) { return HAL_ERROR; } else { - htim->State = HAL_TIM_STATE_BUSY; + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_BUSY); } } else { - /* nothing to do */ + return HAL_ERROR; } switch (Channel) @@ -738,15 +921,17 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Chan case TIM_CHANNEL_1: { /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseNCplt; htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; + htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAErrorCCxN ; /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, + Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the TIM Output Compare DMA request */ @@ -757,15 +942,17 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Chan case TIM_CHANNEL_2: { /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseNCplt; htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; + htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAErrorCCxN ; /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, + Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the TIM Output Compare DMA request */ @@ -776,15 +963,17 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Chan case TIM_CHANNEL_3: { /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseNCplt; htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; + htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAErrorCCxN ; /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, + Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the TIM Output Compare DMA request */ @@ -793,24 +982,35 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Chan } default: + status = HAL_ERROR; break; } - /* Enable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + if (status == HAL_OK) + { + /* Enable the Capture compare channel N */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); + /* Enable the Main Output */ + __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else + { + __HAL_TIM_ENABLE(htim); + } } /* Return function status */ - return HAL_OK; + return status; } /** @@ -826,6 +1026,8 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Chan */ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { + HAL_StatusTypeDef status = HAL_OK; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -856,23 +1058,27 @@ HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Chann } default: + status = HAL_ERROR; break; } - /* Disable the Capture compare channel N */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); + if (status == HAL_OK) + { + /* Disable the Capture compare channel N */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Main Output */ + __HAL_TIM_MOE_DISABLE(htim); - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); + /* Disable the Peripheral */ + __HAL_TIM_DISABLE(htim); - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_READY); + } /* Return function status */ - return HAL_OK; + return status; } /** @@ -927,6 +1133,15 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Check the TIM complementary channel state */ + if (TIM_CHANNEL_N_STATE_GET(htim, Channel) != HAL_TIM_CHANNEL_STATE_READY) + { + return HAL_ERROR; + } + + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_BUSY); + /* Enable the complementary PWM output */ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); @@ -934,8 +1149,15 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel __HAL_TIM_MOE_ENABLE(htim); /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else { __HAL_TIM_ENABLE(htim); } @@ -968,6 +1190,9 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -985,11 +1210,21 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmpsmcr; /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); + /* Check the TIM complementary channel state */ + if (TIM_CHANNEL_N_STATE_GET(htim, Channel) != HAL_TIM_CHANNEL_STATE_READY) + { + return HAL_ERROR; + } + + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_BUSY); + switch (Channel) { case TIM_CHANNEL_1: @@ -1014,27 +1249,38 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Chan } default: + status = HAL_ERROR; break; } - /* Enable the TIM Break interrupt */ - __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); + if (status == HAL_OK) + { + /* Enable the TIM Break interrupt */ + __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK); - /* Enable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + /* Enable the complementary PWM output */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); + /* Enable the Main Output */ + __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else + { + __HAL_TIM_ENABLE(htim); + } } /* Return function status */ - return HAL_OK; + return status; } /** @@ -1050,6 +1296,7 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Chan */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmpccer; /* Check the parameters */ @@ -1079,27 +1326,34 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Chann } default: + status = HAL_ERROR; break; } - /* Disable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - - /* Disable the TIM Break interrupt (only if no more channel is active) */ - tmpccer = htim->Instance->CCER; - if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) + if (status == HAL_OK) { - __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); - } + /* Disable the complementary PWM output */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); + /* Disable the TIM Break interrupt (only if no more channel is active) */ + tmpccer = htim->Instance->CCER; + if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET) + { + __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK); + } - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); + /* Disable the Main Output */ + __HAL_TIM_MOE_DISABLE(htim); + + /* Disable the Peripheral */ + __HAL_TIM_DISABLE(htim); + + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_READY); + } /* Return function status */ - return HAL_OK; + return status; } /** @@ -1115,46 +1369,52 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Chann * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ -HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) +HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, const uint32_t *pData, + uint16_t Length) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmpsmcr; /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); - if (htim->State == HAL_TIM_STATE_BUSY) + /* Set the TIM complementary channel state */ + if (TIM_CHANNEL_N_STATE_GET(htim, Channel) == HAL_TIM_CHANNEL_STATE_BUSY) { return HAL_BUSY; } - else if (htim->State == HAL_TIM_STATE_READY) + else if (TIM_CHANNEL_N_STATE_GET(htim, Channel) == HAL_TIM_CHANNEL_STATE_READY) { - if (((uint32_t)pData == 0U) && (Length > 0U)) + if ((pData == NULL) || (Length == 0U)) { return HAL_ERROR; } else { - htim->State = HAL_TIM_STATE_BUSY; + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_BUSY); } } else { - /* nothing to do */ + return HAL_ERROR; } + switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseNCplt; htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; + htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAErrorCCxN ; /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK) + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, + Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the TIM Capture/Compare 1 DMA request */ @@ -1165,15 +1425,17 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Cha case TIM_CHANNEL_2: { /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseNCplt; htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; + htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAErrorCCxN ; /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK) + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, + Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the TIM Capture/Compare 2 DMA request */ @@ -1184,15 +1446,17 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Cha case TIM_CHANNEL_3: { /* Set the DMA compare callbacks */ - htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; + htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseNCplt; htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt; /* Set the DMA error callback */ - htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; + htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAErrorCCxN ; /* Enable the DMA stream */ - if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK) + if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, + Length) != HAL_OK) { + /* Return error status */ return HAL_ERROR; } /* Enable the TIM Capture/Compare 3 DMA request */ @@ -1201,24 +1465,35 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Cha } default: + status = HAL_ERROR; break; } - /* Enable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); + if (status == HAL_OK) + { + /* Enable the complementary PWM output */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE); - /* Enable the Main Output */ - __HAL_TIM_MOE_ENABLE(htim); + /* Enable the Main Output */ + __HAL_TIM_MOE_ENABLE(htim); - /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ - tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; - if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) - { - __HAL_TIM_ENABLE(htim); + /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */ + if (IS_TIM_SLAVE_INSTANCE(htim->Instance)) + { + tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS; + if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr)) + { + __HAL_TIM_ENABLE(htim); + } + } + else + { + __HAL_TIM_ENABLE(htim); + } } /* Return function status */ - return HAL_OK; + return status; } /** @@ -1234,6 +1509,8 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Cha */ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { + HAL_StatusTypeDef status = HAL_OK; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel)); @@ -1264,23 +1541,27 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Chan } default: + status = HAL_ERROR; break; } - /* Disable the complementary PWM output */ - TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); + if (status == HAL_OK) + { + /* Disable the complementary PWM output */ + TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE); - /* Disable the Main Output */ - __HAL_TIM_MOE_DISABLE(htim); + /* Disable the Main Output */ + __HAL_TIM_MOE_DISABLE(htim); - /* Disable the Peripheral */ - __HAL_TIM_DISABLE(htim); + /* Disable the Peripheral */ + __HAL_TIM_DISABLE(htim); - /* Change the htim state */ - htim->State = HAL_TIM_STATE_READY; + /* Set the TIM complementary channel state */ + TIM_CHANNEL_N_STATE_SET(htim, Channel, HAL_TIM_CHANNEL_STATE_READY); + } /* Return function status */ - return HAL_OK; + return status; } /** @@ -1309,8 +1590,10 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Chan /** * @brief Starts the TIM One Pulse signal generation on the complementary * output. + * @note OutputChannel must match the pulse output channel chosen when calling + * @ref HAL_TIM_OnePulse_ConfigChannel(). * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be enabled + * @param OutputChannel pulse output channel to enable * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1318,11 +1601,33 @@ HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Chan */ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { + uint32_t input_channel = (OutputChannel == TIM_CHANNEL_1) ? TIM_CHANNEL_2 : TIM_CHANNEL_1; + HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef channel_2_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_2); + HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef complementary_channel_2_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_2); + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); - /* Enable the complementary One Pulse output */ + /* Check the TIM channels state */ + if ((channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (channel_2_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_2_state != HAL_TIM_CHANNEL_STATE_READY)) + { + return HAL_ERROR; + } + + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + + /* Enable the complementary One Pulse output channel and the Input Capture channel */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE); + TIM_CCxChannelCmd(htim->Instance, input_channel, TIM_CCx_ENABLE); /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); @@ -1334,8 +1639,10 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t Ou /** * @brief Stops the TIM One Pulse signal generation on the complementary * output. + * @note OutputChannel must match the pulse output channel chosen when calling + * @ref HAL_TIM_OnePulse_ConfigChannel(). * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be disabled + * @param OutputChannel pulse output channel to disable * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1343,12 +1650,14 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t Ou */ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { + uint32_t input_channel = (OutputChannel == TIM_CHANNEL_1) ? TIM_CHANNEL_2 : TIM_CHANNEL_1; /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); - /* Disable the complementary One Pulse output */ + /* Disable the complementary One Pulse output channel and the Input Capture channel */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE); + TIM_CCxChannelCmd(htim->Instance, input_channel, TIM_CCx_DISABLE); /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -1356,6 +1665,12 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t Out /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -1363,8 +1678,10 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t Out /** * @brief Starts the TIM One Pulse signal generation in interrupt mode on the * complementary channel. + * @note OutputChannel must match the pulse output channel chosen when calling + * @ref HAL_TIM_OnePulse_ConfigChannel(). * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be enabled + * @param OutputChannel pulse output channel to enable * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1372,17 +1689,39 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t Out */ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { + uint32_t input_channel = (OutputChannel == TIM_CHANNEL_1) ? TIM_CHANNEL_2 : TIM_CHANNEL_1; + HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef channel_2_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_2); + HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1); + HAL_TIM_ChannelStateTypeDef complementary_channel_2_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_2); + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); + /* Check the TIM channels state */ + if ((channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (channel_2_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_1_state != HAL_TIM_CHANNEL_STATE_READY) + || (complementary_channel_2_state != HAL_TIM_CHANNEL_STATE_READY)) + { + return HAL_ERROR; + } + + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY); + /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); - /* Enable the complementary One Pulse output */ + /* Enable the complementary One Pulse output channel and the Input Capture channel */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE); + TIM_CCxChannelCmd(htim->Instance, input_channel, TIM_CCx_ENABLE); /* Enable the Main Output */ __HAL_TIM_MOE_ENABLE(htim); @@ -1394,8 +1733,10 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t /** * @brief Stops the TIM One Pulse signal generation in interrupt mode on the * complementary channel. + * @note OutputChannel must match the pulse output channel chosen when calling + * @ref HAL_TIM_OnePulse_ConfigChannel(). * @param htim TIM One Pulse handle - * @param OutputChannel TIM Channel to be disabled + * @param OutputChannel pulse output channel to disable * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected @@ -1403,6 +1744,8 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t */ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { + uint32_t input_channel = (OutputChannel == TIM_CHANNEL_1) ? TIM_CHANNEL_2 : TIM_CHANNEL_1; + /* Check the parameters */ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel)); @@ -1412,8 +1755,9 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); - /* Disable the complementary One Pulse output */ + /* Disable the complementary One Pulse output channel and the Input Capture channel */ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE); + TIM_CCxChannelCmd(htim->Instance, input_channel, TIM_CCx_DISABLE); /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); @@ -1421,6 +1765,12 @@ HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); + /* Set the TIM channels state */ + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + /* Return function status */ return HAL_OK; } @@ -1649,7 +1999,7 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef *htim, uint3 * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim, - TIM_MasterConfigTypeDef *sMasterConfig) + const TIM_MasterConfigTypeDef *sMasterConfig) { uint32_t tmpcr2; uint32_t tmpsmcr; @@ -1722,7 +2072,7 @@ HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim, * @retval HAL status */ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim, - TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig) + const TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig) { /* Keep this variable initialized to 0 as it is used to configure BDTR register */ uint32_t tmpbdtr = 0U; @@ -1754,6 +2104,17 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim, MODIFY_REG(tmpbdtr, TIM_BDTR_AOE, sBreakDeadTimeConfig->AutomaticOutput); MODIFY_REG(tmpbdtr, TIM_BDTR_BKF, (sBreakDeadTimeConfig->BreakFilter << TIM_BDTR_BKF_Pos)); +#if defined(TIM_BDTR_BKBID) + if (IS_TIM_ADVANCED_INSTANCE(htim->Instance)) + { + /* Check the parameters */ + assert_param(IS_TIM_BREAK_AFMODE(sBreakDeadTimeConfig->BreakAFMode)); + + /* Set BREAK AF mode */ + MODIFY_REG(tmpbdtr, TIM_BDTR_BKBID, sBreakDeadTimeConfig->BreakAFMode); + } + +#endif /* TIM_BDTR_BKBID */ if (IS_TIM_BKIN2_INSTANCE(htim->Instance)) { /* Check the parameters */ @@ -1765,6 +2126,17 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim, MODIFY_REG(tmpbdtr, TIM_BDTR_BK2F, (sBreakDeadTimeConfig->Break2Filter << TIM_BDTR_BK2F_Pos)); MODIFY_REG(tmpbdtr, TIM_BDTR_BK2E, sBreakDeadTimeConfig->Break2State); MODIFY_REG(tmpbdtr, TIM_BDTR_BK2P, sBreakDeadTimeConfig->Break2Polarity); +#if defined(TIM_BDTR_BKBID) + + if (IS_TIM_ADVANCED_INSTANCE(htim->Instance)) + { + /* Check the parameters */ + assert_param(IS_TIM_BREAK2_AFMODE(sBreakDeadTimeConfig->Break2AFMode)); + + /* Set BREAK2 AF mode */ + MODIFY_REG(tmpbdtr, TIM_BDTR_BK2BID, sBreakDeadTimeConfig->Break2AFMode); + } +#endif /* TIM_BDTR_BKBID */ } /* Set TIMx_BDTR */ @@ -1788,9 +2160,10 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim, */ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakInput(TIM_HandleTypeDef *htim, uint32_t BreakInput, - TIMEx_BreakInputConfigTypeDef *sBreakInputConfig) + const TIMEx_BreakInputConfigTypeDef *sBreakInputConfig) { + HAL_StatusTypeDef status = HAL_OK; uint32_t tmporx; uint32_t bkin_enable_mask; uint32_t bkin_polarity_mask; @@ -1839,7 +2212,7 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakInput(TIM_HandleTypeDef *htim, case TIM_BREAKINPUTSOURCE_DFSDM1: { bkin_enable_mask = TIM1_AF1_BKDF1BK0E; - bkin_enable_bitpos = 8U; + bkin_enable_bitpos = TIM1_AF1_BKDF1BK0E_Pos; bkin_polarity_mask = 0U; bkin_polarity_bitpos = 0U; break; @@ -1898,12 +2271,13 @@ HAL_StatusTypeDef HAL_TIMEx_ConfigBreakInput(TIM_HandleTypeDef *htim, break; } default: + status = HAL_ERROR; break; } __HAL_UNLOCK(htim); - return HAL_OK; + return status; } #endif /*TIM_BREAK_INPUT_SUPPORT */ @@ -2131,6 +2505,140 @@ HAL_StatusTypeDef HAL_TIMEx_GroupChannel5(TIM_HandleTypeDef *htim, uint32_t Chan return HAL_OK; } +#if defined(TIM_BDTR_BKBID) + +/** + * @brief Disarm the designated break input (when it operates in bidirectional mode). + * @param htim TIM handle. + * @param BreakInput Break input to disarm + * This parameter can be one of the following values: + * @arg TIM_BREAKINPUT_BRK: Timer break input + * @arg TIM_BREAKINPUT_BRK2: Timer break 2 input + * @note The break input can be disarmed only when it is configured in + * bidirectional mode and when when MOE is reset. + * @note Purpose is to be able to have the input voltage back to high-state, + * whatever the time constant on the output . + * @retval HAL status + */ +HAL_StatusTypeDef HAL_TIMEx_DisarmBreakInput(TIM_HandleTypeDef *htim, uint32_t BreakInput) +{ + HAL_StatusTypeDef status = HAL_OK; + uint32_t tmpbdtr; + + /* Check the parameters */ + assert_param(IS_TIM_ADVANCED_INSTANCE(htim->Instance)); + assert_param(IS_TIM_BREAKINPUT(BreakInput)); + + switch (BreakInput) + { + case TIM_BREAKINPUT_BRK: + { + /* Check initial conditions */ + tmpbdtr = READ_REG(htim->Instance->BDTR); + if ((READ_BIT(tmpbdtr, TIM_BDTR_BKBID) == TIM_BDTR_BKBID) && + (READ_BIT(tmpbdtr, TIM_BDTR_MOE) == 0U)) + { + /* Break input BRK is disarmed */ + SET_BIT(htim->Instance->BDTR, TIM_BDTR_BKDSRM); + } + break; + } + + case TIM_BREAKINPUT_BRK2: + { + /* Check initial conditions */ + tmpbdtr = READ_REG(htim->Instance->BDTR); + if ((READ_BIT(tmpbdtr, TIM_BDTR_BK2BID) == TIM_BDTR_BK2BID) && + (READ_BIT(tmpbdtr, TIM_BDTR_MOE) == 0U)) + { + /* Break input BRK is disarmed */ + SET_BIT(htim->Instance->BDTR, TIM_BDTR_BK2DSRM); + } + break; + } + default: + status = HAL_ERROR; + break; + } + + return status; +} + +/** + * @brief Arm the designated break input (when it operates in bidirectional mode). + * @param htim TIM handle. + * @param BreakInput Break input to arm + * This parameter can be one of the following values: + * @arg TIM_BREAKINPUT_BRK: Timer break input + * @arg TIM_BREAKINPUT_BRK2: Timer break 2 input + * @note Arming is possible at anytime, even if fault is present. + * @note Break input is automatically armed as soon as MOE bit is set. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_TIMEx_ReArmBreakInput(TIM_HandleTypeDef *htim, uint32_t BreakInput) +{ + HAL_StatusTypeDef status = HAL_OK; + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_TIM_ADVANCED_INSTANCE(htim->Instance)); + assert_param(IS_TIM_BREAKINPUT(BreakInput)); + + switch (BreakInput) + { + case TIM_BREAKINPUT_BRK: + { + /* Check initial conditions */ + if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BKBID) == TIM_BDTR_BKBID) + { + /* Break input BRK is re-armed automatically by hardware. Poll to check whether fault condition disappeared */ + /* Init tickstart for timeout management */ + tickstart = HAL_GetTick(); + while (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BKDSRM) != 0UL) + { + if ((HAL_GetTick() - tickstart) > TIM_BREAKINPUT_REARM_TIMEOUT) + { + /* New check to avoid false timeout detection in case of preemption */ + if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BKDSRM) != 0UL) + { + return HAL_TIMEOUT; + } + } + } + } + break; + } + + case TIM_BREAKINPUT_BRK2: + { + /* Check initial conditions */ + if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BK2BID) == TIM_BDTR_BK2BID) + { + /* Break input BRK2 is re-armed automatically by hardware. Poll to check whether fault condition disappeared */ + /* Init tickstart for timeout management */ + tickstart = HAL_GetTick(); + while (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BK2DSRM) != 0UL) + { + if ((HAL_GetTick() - tickstart) > TIM_BREAKINPUT_REARM_TIMEOUT) + { + /* New check to avoid false timeout detection in case of preemption */ + if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BK2DSRM) != 0UL) + { + return HAL_TIMEOUT; + } + } + } + } + break; + } + default: + status = HAL_ERROR; + break; + } + + return status; +} +#endif /* TIM_BDTR_BKBID */ /** * @} @@ -2236,12 +2744,33 @@ __weak void HAL_TIMEx_Break2Callback(TIM_HandleTypeDef *htim) * @param htim TIM Hall Sensor handle * @retval HAL state */ -HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim) +HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(const TIM_HandleTypeDef *htim) { return htim->State; } /** + * @brief Return actual state of the TIM complementary channel. + * @param htim TIM handle + * @param ChannelN TIM Complementary channel + * This parameter can be one of the following values: + * @arg TIM_CHANNEL_1: TIM Channel 1 + * @arg TIM_CHANNEL_2: TIM Channel 2 + * @arg TIM_CHANNEL_3: TIM Channel 3 + * @retval TIM Complementary channel state + */ +HAL_TIM_ChannelStateTypeDef HAL_TIMEx_GetChannelNState(const TIM_HandleTypeDef *htim, uint32_t ChannelN) +{ + HAL_TIM_ChannelStateTypeDef channel_state; + + /* Check the parameters */ + assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, ChannelN)); + + channel_state = TIM_CHANNEL_N_STATE_GET(htim, ChannelN); + + return channel_state; +} +/** * @} */ @@ -2250,7 +2779,7 @@ HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim) */ /* Private functions ---------------------------------------------------------*/ -/** @defgroup TIMEx_Private_Functions TIMEx Private Functions +/** @defgroup TIMEx_Private_Functions TIM Extended Private Functions * @ingroup RTEMSBSPsARMSTM32H7 * @{ */ @@ -2295,6 +2824,103 @@ void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef *hdma) /** + * @brief TIM DMA Delay Pulse complete callback (complementary channel). + * @param hdma pointer to DMA handle. + * @retval None + */ +static void TIM_DMADelayPulseNCplt(DMA_HandleTypeDef *hdma) +{ + TIM_HandleTypeDef *htim = (TIM_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + if (hdma == htim->hdma[TIM_DMA_ID_CC1]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; + + if (hdma->Init.Mode == DMA_NORMAL) + { + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + } + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC2]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; + + if (hdma->Init.Mode == DMA_NORMAL) + { + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + } + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC3]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; + + if (hdma->Init.Mode == DMA_NORMAL) + { + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_3, HAL_TIM_CHANNEL_STATE_READY); + } + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC4]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; + + if (hdma->Init.Mode == DMA_NORMAL) + { + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_4, HAL_TIM_CHANNEL_STATE_READY); + } + } + else + { + /* nothing to do */ + } + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->PWM_PulseFinishedCallback(htim); +#else + HAL_TIM_PWM_PulseFinishedCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; +} + +/** + * @brief TIM DMA error callback (complementary channel) + * @param hdma pointer to DMA handle. + * @retval None + */ +static void TIM_DMAErrorCCxN(DMA_HandleTypeDef *hdma) +{ + TIM_HandleTypeDef *htim = (TIM_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + if (hdma == htim->hdma[TIM_DMA_ID_CC1]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY); + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC2]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY); + } + else if (hdma == htim->hdma[TIM_DMA_ID_CC3]) + { + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; + TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_3, HAL_TIM_CHANNEL_STATE_READY); + } + else + { + /* nothing to do */ + } + +#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1) + htim->ErrorCallback(htim); +#else + HAL_TIM_ErrorCallback(htim); +#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */ + + htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; +} + +/** * @brief Enables or disables the TIM Capture Compare Channel xN. * @param TIMx to select the TIM peripheral * @param Channel specifies the TIM Channel @@ -2330,5 +2956,3 @@ static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t Cha /** * @} */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |