diff options
Diffstat (limited to 'bsps/arm/stm32h7/hal/stm32h7xx_hal_rtc_ex.c')
-rw-r--r-- | bsps/arm/stm32h7/hal/stm32h7xx_hal_rtc_ex.c | 5899 |
1 files changed, 2882 insertions, 3017 deletions
diff --git a/bsps/arm/stm32h7/hal/stm32h7xx_hal_rtc_ex.c b/bsps/arm/stm32h7/hal/stm32h7xx_hal_rtc_ex.c index 2e0bbae94f..252dce91b8 100644 --- a/bsps/arm/stm32h7/hal/stm32h7xx_hal_rtc_ex.c +++ b/bsps/arm/stm32h7/hal/stm32h7xx_hal_rtc_ex.c @@ -1,3017 +1,2882 @@ -/**
- ******************************************************************************
- * @file stm32h7xx_hal_rtc_ex.c
- * @author MCD Application Team
- * @brief Extended RTC HAL module driver.
- * This file provides firmware functions to manage the following
- * functionalities of the Real Time Clock (RTC) Extended peripheral:
- * + RTC Time Stamp functions
- * + RTC Tamper functions
- * + RTC Wake-up functions
- * + Extended Control functions
- * + Extended RTC features functions
- *
- @verbatim
- ==============================================================================
- ##### How to use this driver #####
- ==============================================================================
- [..]
- (+) Enable the RTC domain access.
- (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour
- format using the HAL_RTC_Init() function.
-
- *** RTC Wakeup configuration ***
- ================================
- [..]
- (+) To configure the RTC Wakeup Clock source and Counter use the HAL_RTCEx_SetWakeUpTimer()
- function. You can also configure the RTC Wakeup timer with interrupt mode
- using the HAL_RTCEx_SetWakeUpTimer_IT() function.
- (+) To read the RTC WakeUp Counter register, use the HAL_RTCEx_GetWakeUpTimer()
- function.
-
- *** Outputs configuration ***
- =============================
- [..] The RTC has 2 different outputs:
- (+) RTC_ALARM: this output is used to manage the RTC Alarm A, Alarm B
- and WaKeUp signals.
- To output the selected RTC signal, use the HAL_RTC_Init() function.
- (+) RTC_CALIB: this output is 512Hz signal or 1Hz.
- To enable the RTC_CALIB, use the HAL_RTCEx_SetCalibrationOutPut() function.
- (+) Two pins can be used as RTC_ALARM or RTC_CALIB (PC13, PB2) managed on
- the RTC_OR register.
- (+) When the RTC_CALIB or RTC_ALARM output is selected, the RTC_OUT pin is
- automatically configured in output alternate function.
-
- *** Smooth digital Calibration configuration ***
- ================================================
- [..]
- (+) Configure the RTC Original Digital Calibration Value and the corresponding
- calibration cycle period (32s,16s and 8s) using the HAL_RTCEx_SetSmoothCalib()
- function.
-
- *** TimeStamp configuration ***
- ===============================
- [..]
- (+) Enable the RTC TimeStamp using the HAL_RTCEx_SetTimeStamp() function.
- You can also configure the RTC TimeStamp with interrupt mode using the
- HAL_RTCEx_SetTimeStamp_IT() function.
- (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp()
- function.
-
- *** Internal TimeStamp configuration ***
- ===============================
- [..]
- (+) Enable the RTC internal TimeStamp using the HAL_RTCEx_SetInternalTimeStamp() function.
- User has to check internal timestamp occurrence using __HAL_RTC_INTERNAL_TIMESTAMP_GET_FLAG.
- (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp()
- function.
-
- *** Tamper configuration ***
- ============================
- [..]
- (+) Enable the RTC Tamper and configure the Tamper filter count, trigger Edge
- or Level according to the Tamper filter (if equal to 0 Edge else Level)
- value, sampling frequency, NoErase, MaskFlag, precharge or discharge and
- Pull-UP using the HAL_RTCEx_SetTamper() function. You can configure RTC Tamper
- with interrupt mode using HAL_RTCEx_SetTamper_IT() function.
- (+) The default configuration of the Tamper erases the backup registers. To avoid
- erase, enable the NoErase field on the RTC_TAMPCR register.
-
- *** Backup Data Registers configuration ***
- ===========================================
- [..]
- (+) To write to the RTC Backup Data registers, use the HAL_RTCEx_BKUPWrite()
- function.
- (+) To read the RTC Backup Data registers, use the HAL_RTCEx_BKUPRead()
- function.
-
- @endverbatim
- ******************************************************************************
- * @attention
- *
- * <h2><center>© Copyright (c) 2017 STMicroelectronics.
- * All rights reserved.</center></h2>
- *
- * This software component is licensed by ST under BSD 3-Clause license,
- * the "License"; You may not use this file except in compliance with the
- * License. You may obtain a copy of the License at:
- * opensource.org/licenses/BSD-3-Clause
- *
- ******************************************************************************
- */
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32h7xx_hal.h"
-
-/** @addtogroup STM32H7xx_HAL_Driver
- * @{
- */
-
-/** @addtogroup RTCEx
- * @brief RTC Extended HAL module driver
- * @{
- */
-
-#ifdef HAL_RTC_MODULE_ENABLED
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private define ------------------------------------------------------------*/
-#define TAMP_ALL (TAMP_CR1_TAMP1E | TAMP_CR1_TAMP2E | TAMP_CR1_TAMP3E)
-
-/* Private macro -------------------------------------------------------------*/
-/* Private variables ---------------------------------------------------------*/
-/* Private function prototypes -----------------------------------------------*/
-/* Exported functions --------------------------------------------------------*/
-
-/** @addtogroup RTCEx_Exported_Functions
- * @{
- */
-
-
-/** @addtogroup RTCEx_Exported_Functions_Group1
- * @brief RTC TimeStamp and Tamper functions
- *
-@verbatim
- ===============================================================================
- ##### RTC TimeStamp and Tamper functions #####
- ===============================================================================
-
- [..] This section provides functions allowing to configure TimeStamp feature
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Set TimeStamp.
- * @note This API must be called before enabling the TimeStamp feature.
- * @param hrtc RTC handle
- * @param TimeStampEdge Specifies the pin edge on which the TimeStamp is
- * activated.
- * This parameter can be one of the following values:
- * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the
- * rising edge of the related pin.
- * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the
- * falling edge of the related pin.
- * @param RTC_TimeStampPin specifies the RTC TimeStamp Pin.
- * This parameter can be one of the following values:
- * @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin.
- * The RTC TimeStamp Pin is per default PC13, but for reasons of
- * compatibility, this parameter is required.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin)
-{
- uint32_t tmpreg;
-
- /* Check the parameters */
- assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge));
- assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin));
-
- /* Prevent unused argument(s) compilation warning if no assert_param check */
- UNUSED(RTC_TimeStampPin);
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Get the RTC_CR register and clear the bits to be configured */
- tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE));
-
- tmpreg |= TimeStampEdge;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Configure the Time Stamp TSEDGE and Enable bits */
- hrtc->Instance->CR = (uint32_t)tmpreg;
-
- __HAL_RTC_TIMESTAMP_ENABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Set TimeStamp with Interrupt.
- * @note This API must be called before enabling the TimeStamp feature.
- * @param hrtc RTC handle
- * @param TimeStampEdge Specifies the pin edge on which the TimeStamp is
- * activated.
- * This parameter can be one of the following values:
- * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the
- * rising edge of the related pin.
- * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the
- * falling edge of the related pin.
- * @param RTC_TimeStampPin Specifies the RTC TimeStamp Pin.
- * This parameter can be one of the following values:
- * @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin.
- * The RTC TimeStamp Pin is per default PC13, but for reasons of
- * compatibility, this parameter is required.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin)
-{
- uint32_t tmpreg;
-
- /* Check the parameters */
- assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge));
- assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin));
-
- /* Prevent unused argument(s) compilation warning if no assert_param check */
- UNUSED(RTC_TimeStampPin);
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Get the RTC_CR register and clear the bits to be configured */
- tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE));
-
- tmpreg |= TimeStampEdge;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Configure the Time Stamp TSEDGE and Enable bits */
- hrtc->Instance->CR = (uint32_t)tmpreg;
-
- __HAL_RTC_TIMESTAMP_ENABLE(hrtc);
-
- /* Enable IT timestamp */
- __HAL_RTC_TIMESTAMP_ENABLE_IT(hrtc, RTC_IT_TS);
-
-#if !defined(DUAL_CORE)
- /* RTC timestamp Interrupt Configuration: EXTI configuration */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
-#endif
-
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE();
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Deactivate TimeStamp.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc)
-{
- uint32_t tmpreg;
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* In case of interrupt mode is used, the interrupt source must disabled */
- __HAL_RTC_TIMESTAMP_DISABLE_IT(hrtc, RTC_IT_TS);
-
- /* Get the RTC_CR register and clear the bits to be configured */
- tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE));
-
- /* Configure the Time Stamp TSEDGE and Enable bits */
- hrtc->Instance->CR = (uint32_t)tmpreg;
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Set Internal TimeStamp.
- * @note This API must be called before enabling the internal TimeStamp feature.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetInternalTimeStamp(RTC_HandleTypeDef *hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Configure the internal Time Stamp Enable bits */
- __HAL_RTC_INTERNAL_TIMESTAMP_ENABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Deactivate Internal TimeStamp.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTimeStamp(RTC_HandleTypeDef *hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Configure the internal Time Stamp Enable bits */
- __HAL_RTC_INTERNAL_TIMESTAMP_DISABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Get the RTC TimeStamp value.
- * @param hrtc RTC handle
- * @param sTimeStamp Pointer to Time structure
- * @param sTimeStampDate Pointer to Date structure
- * @param Format specifies the format of the entered parameters.
- * This parameter can be one of the following values:
- * @arg RTC_FORMAT_BIN: Binary data format
- * @arg RTC_FORMAT_BCD: BCD data format
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTimeStamp, RTC_DateTypeDef *sTimeStampDate, uint32_t Format)
-{
- uint32_t tmptime;
- uint32_t tmpdate;
-
- /* Check the parameters */
- assert_param(IS_RTC_FORMAT(Format));
-
- /* Get the TimeStamp time and date registers values */
- tmptime = (uint32_t)(hrtc->Instance->TSTR & RTC_TR_RESERVED_MASK);
- tmpdate = (uint32_t)(hrtc->Instance->TSDR & RTC_DR_RESERVED_MASK);
-
- /* Fill the Time structure fields with the read parameters */
- sTimeStamp->Hours = (uint8_t)((tmptime & (RTC_TSTR_HT | RTC_TSTR_HU)) >> RTC_TSTR_HU_Pos);
- sTimeStamp->Minutes = (uint8_t)((tmptime & (RTC_TSTR_MNT | RTC_TSTR_MNU)) >> RTC_TSTR_MNU_Pos);
- sTimeStamp->Seconds = (uint8_t)((tmptime & (RTC_TSTR_ST | RTC_TSTR_SU)) >> RTC_TSTR_SU_Pos);
- sTimeStamp->TimeFormat = (uint8_t)((tmptime & (RTC_TSTR_PM)) >> RTC_TSTR_PM_Pos);
- sTimeStamp->SubSeconds = (uint32_t) hrtc->Instance->TSSSR;
-
- /* Fill the Date structure fields with the read parameters */
- sTimeStampDate->Year = 0U;
- sTimeStampDate->Month = (uint8_t)((tmpdate & (RTC_TSDR_MT | RTC_TSDR_MU)) >> RTC_TSDR_MU_Pos);
- sTimeStampDate->Date = (uint8_t)((tmpdate & (RTC_TSDR_DT | RTC_TSDR_DU)) >> RTC_TSDR_DU_Pos);
- sTimeStampDate->WeekDay = (uint8_t)((tmpdate & (RTC_TSDR_WDU)) >> RTC_TSDR_WDU_Pos);
-
- /* Check the input parameters format */
- if (Format == RTC_FORMAT_BIN)
- {
- /* Convert the TimeStamp structure parameters to Binary format */
- sTimeStamp->Hours = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Hours);
- sTimeStamp->Minutes = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Minutes);
- sTimeStamp->Seconds = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Seconds);
-
- /* Convert the DateTimeStamp structure parameters to Binary format */
- sTimeStampDate->Month = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Month);
- sTimeStampDate->Date = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Date);
- sTimeStampDate->WeekDay = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->WeekDay);
- }
-
- /* Clear the TIMESTAMP Flags */
- __HAL_RTC_INTERNAL_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_ITSF);
- __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF);
-
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group5
- * @brief Extended RTC Tamper functions
- *
-@verbatim
- ==============================================================================
- ##### Tamper functions #####
- ==============================================================================
- [..]
- (+) Before calling any tamper or internal tamper function, you have to call first
- HAL_RTC_Init() function.
- (+) In that ine you can select to output tamper event on RTC pin.
- [..]
- (+) Enable the Tamper and configure the Tamper filter count, trigger Edge
- or Level according to the Tamper filter (if equal to 0 Edge else Level)
- value, sampling frequency, NoErase, MaskFlag, precharge or discharge and
- Pull-UP, timestamp using the HAL_RTCEx_SetTamper() function.
- You can configure Tamper with interrupt mode using HAL_RTCEx_SetTamper_IT() function.
- (+) The default configuration of the Tamper erases the backup registers. To avoid
- erase, enable the NoErase field on the TAMP_TAMPCR register.
- [..]
- (+) Enable Internal Tamper and configure it with interrupt, timestamp using
- the HAL_RTCEx_SetInternalTamper() function.
-
-@endverbatim
-* @{
-*/
-
-#if defined(TAMP_CR1_TAMP1E)
-/**
- * @brief Set Tamper
- * @param hrtc RTC handle
- * @param sTamper Pointer to Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper)
-{
- uint32_t tmpreg;
-
- /* Point on TAMPER registers base address */
- TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET);
-
- /* Check the parameters */
- assert_param(IS_RTC_TAMPER(sTamper->Tamper));
- assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger));
- assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase));
- assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag));
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection));
- assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter));
- assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency));
- assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration));
- assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp));
- assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger));
-
- /* Configuration register 2 */
- tmpreg = tamp->CR2;
- tmpreg &= ~((sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos));
-
- /* Configure the tamper trigger bit */
- if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE))
- {
- tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos);
- }
-
- /* Configure the tamper flags masking bit */
- if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE)
- {
- tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos);
- }
-
- /* Configure the tamper backup registers erasure bit */
- if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE)
- {
- tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos);
- }
- tamp->CR2 = tmpreg;
-
- /* Configure filtering parameters */
- tamp->FLTCR = (sTamper->Filter) | (sTamper->SamplingFrequency) | \
- (sTamper->PrechargeDuration) | (sTamper->TamperPullUp);
-
- /* Configure Timestamp saving on tamper detection */
- if ((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sTamper->TimeStampOnTamperDetection))
- {
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
- tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS);
- hrtc->Instance->CR = (tmpreg | (sTamper->TimeStampOnTamperDetection));
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
- }
-
- /* Enable selected tamper */
- tamp->CR1 |= (sTamper->Tamper);
-
- return HAL_OK;
-}
-#endif /* TAMP_CR1_TAMP1E */
-#if defined (RTC_TAMPCR_TAMP1E)
-/**
- * @brief Set Tamper.
- * @note By calling this API we disable the tamper interrupt for all tampers.
- * @param hrtc RTC handle
- * @param sTamper Pointer to Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper)
-{
- uint32_t tmpreg;
-
- /* Check the parameters */
- assert_param(IS_RTC_TAMPER(sTamper->Tamper));
- assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger));
- assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase));
- assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag));
- assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter));
- assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency));
- assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration));
- assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp));
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection));
- assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Copy control register into temporary variable */
- tmpreg = hrtc->Instance->TAMPCR;
-
- /* Enable selected tamper */
- tmpreg |= (sTamper->Tamper);
-
- /* Configure the bit (located just next to the tamper enable bit) */
- if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE))
- {
- /* Set the tamper trigger bit */
- tmpreg |= (uint32_t)(sTamper->Tamper << 1U);
- }
- else
- {
- /* Clear the tamper trigger bit */
- tmpreg &= (uint32_t)~(sTamper->Tamper << 1U);
- }
-
- /* Configure the tamper backup registers erasure bit */
- if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE)
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
- else
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
-
- /* Configure the tamper flags masking bit */
- if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE)
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1MF);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2MF);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3MF);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
- else
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1MF);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2MF);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3MF);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
-
- /* Clearing remaining fields before setting them */
- tmpreg &= ~(RTC_TAMPERFILTER_MASK | RTC_TAMPERSAMPLINGFREQ_RTCCLK_MASK | \
- RTC_TAMPERPRECHARGEDURATION_MASK | RTC_TAMPER_PULLUP_MASK | \
- RTC_TIMESTAMPONTAMPERDETECTION_MASK);
-
- /* Set remaining parameters of desired configuration into temporary variable */
- tmpreg |= ((uint32_t)sTamper->Filter | \
- (uint32_t)sTamper->SamplingFrequency | \
- (uint32_t)sTamper->PrechargeDuration | \
- (uint32_t)sTamper->TamperPullUp | \
- (uint32_t)sTamper->TimeStampOnTamperDetection);
-
- /* Copy desired configuration into configuration register */
- hrtc->Instance->TAMPCR = tmpreg;
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-#endif /* RTC_TAMPCR_TAMP1E */
-
-#if defined(TAMP_CR1_TAMP1E)
-/**
- * @brief Set Tamper with interrupt.
- * @param hrtc RTC handle
- * @param sTamper Pointer to Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper)
-{
- uint32_t tmpreg;
-
- /* Point on TAMPER registers base address */
- TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET);
-
- /* Check the parameters */
- assert_param(IS_RTC_TAMPER(sTamper->Tamper));
- assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger));
- assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase));
- assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag));
- assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter));
- assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency));
- assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration));
- assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp));
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection));
- assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger));
-
- /* Copy configuration register into temporary variable */
- tmpreg = tamp->CR2;
-
- /* Clear the bits that are going to be configured and leave the others unchanged */
- tmpreg &= ~((sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos));
-
- /* Configure the tamper trigger bit */
- if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE))
- {
- tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos);
- }
-
- /* Configure the tamper flags masking bit */
- if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE)
- {
- tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos);
- }
-
- /* Configure the tamper backup registers erasure bit */
- if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE)
- {
- tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos);
- }
- tamp->CR2 = tmpreg;
-
- /* Configure filtering parameters */
- tamp->FLTCR = (sTamper->Filter) | (sTamper->SamplingFrequency) | \
- (sTamper->PrechargeDuration) | (sTamper->TamperPullUp);
-
- /* Configure Timestamp saving on tamper detection */
- if ((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sTamper->TimeStampOnTamperDetection))
- {
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
- tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS);
- hrtc->Instance->CR = (tmpreg | (sTamper->TimeStampOnTamperDetection));
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
- }
-
- /* Configure RTC Tamper Interrupt: EXTI configuration */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_FALLING_EDGE();
-
- /* Enable interrupt on selected tamper */
- tamp->IER |= sTamper->Tamper;
-
- /* Enable selected tamper */
- tamp->CR1 |= sTamper->Tamper;
-
- return HAL_OK;
-}
-#endif /* TAMP_CR1_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP1E)
-/**
- * @brief Set Tamper with interrupt.
- * @note By calling this API we force the tamper interrupt for all tampers.
- * @param hrtc RTC handle
- * @param sTamper Pointer to Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper)
-{
- uint32_t tmpreg;
-
- /* Check the parameters */
- assert_param(IS_RTC_TAMPER(sTamper->Tamper));
- assert_param(IS_RTC_TAMPER_INTERRUPT(sTamper->Interrupt));
- assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger));
- assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase));
- assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag));
- assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter));
- assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency));
- assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration));
- assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp));
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection));
- assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Copy control register into temporary variable */
- tmpreg = hrtc->Instance->TAMPCR;
-
- /* Enable selected tamper */
- tmpreg |= (sTamper->Tamper);
-
- /* Configure the tamper trigger bit (located just next to the tamper enable bit) */
- if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE))
- {
- /* Set the tamper trigger bit */
- tmpreg |= (uint32_t)(sTamper->Tamper << 1U);
- }
- else
- {
- /* Clear the tamper trigger bit */
- tmpreg &= (uint32_t)~(sTamper->Tamper << 1U);
- }
-
- /* Configure the tamper backup registers erasure bit */
- if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE)
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
- else
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3NOERASE);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
-
- /* Configure the tamper flags masking bit */
- if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE)
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1MF);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2MF);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3MF);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
- else
- {
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((sTamper->Tamper & RTC_TAMPER_1) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1MF);
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((sTamper->Tamper & RTC_TAMPER_2) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2MF);
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((sTamper->Tamper & RTC_TAMPER_3) != 0U)
- {
- tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3MF);
- }
-#endif /* RTC_TAMPCR_TAMP3E */
- }
-
- /* Clearing remaining fields before setting them */
- tmpreg &= ~(RTC_TAMPERFILTER_MASK | RTC_TAMPERSAMPLINGFREQ_RTCCLK_MASK | \
- RTC_TAMPERPRECHARGEDURATION_MASK | RTC_TAMPER_PULLUP_MASK | \
- RTC_TIMESTAMPONTAMPERDETECTION_MASK);
-
- /* Set remaining parameters of desired configuration into temporary variable */
- tmpreg |= ((uint32_t)sTamper->Filter | \
- (uint32_t)sTamper->SamplingFrequency | \
- (uint32_t)sTamper->PrechargeDuration | \
- (uint32_t)sTamper->TamperPullUp | \
- (uint32_t)sTamper->TimeStampOnTamperDetection);
-
- /* Enable interrupt on selected tamper */
- tmpreg |= (uint32_t)sTamper->Interrupt;
-
- /* Copy desired configuration into configuration register */
- hrtc->Instance->TAMPCR = tmpreg;
-
-#if !defined(DUAL_CORE)
- /* RTC Tamper Interrupt Configuration: EXTI configuration */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
-#endif
-
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE();
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-#endif /* RTC_TAMPCR_TAMP1E */
-
-#if defined(TAMP_CR1_TAMP1E)
-/**
- * @brief Deactivate Tamper.
- * @param hrtc RTC handle
- * @param Tamper Selected tamper pin.
- * This parameter can be a combination of the following values:
- * @arg RTC_TAMPER_1
- * @arg RTC_TAMPER_2
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef * hrtc, uint32_t Tamper)
-{
- /* Point on TAMPER registers base address */
- TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET);
-
- assert_param(IS_RTC_TAMPER(Tamper));
-
- /* Disable the selected Tamper pin */
- tamp->CR1 &= ~Tamper;
-
- /* Disable the selected Tamper interrupt */
- tamp->IER &= ~Tamper;
-
- /* Clear the selected tamper flags in SR register by setting corresponding bits in SCR register */
- tamp->SCR = Tamper;
-
- /* Clear the selected tamper configuration (trigger, mask flag, and no-erase) */
- tamp->CR2 &= ~((Tamper << TAMP_CR2_TAMP1TRG_Pos) | (Tamper << TAMP_CR2_TAMP1MSK_Pos) | (Tamper << TAMP_CR2_TAMP1NOERASE_Pos));
-
- return HAL_OK;
-}
-#endif /* TAMP_CR1_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP1E)
-/**
- * @brief Deactivate Tamper.
- * @param hrtc RTC handle
- * @param Tamper Selected tamper pin.
- * This parameter can be any combination of the following values:
- * @arg RTC_TAMPER_1
- * @arg RTC_TAMPER_2
- * @arg RTC_TAMPER_3
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef * hrtc, uint32_t Tamper)
-{
- assert_param(IS_RTC_TAMPER(Tamper));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the selected Tamper pin */
- hrtc->Instance->TAMPCR &= ((uint32_t)~Tamper);
-
- /* Disable the selected Tamper interrupt */
-#if defined(RTC_TAMPCR_TAMP1E)
- if ((Tamper & RTC_TAMPER_1) != 0U)
- {
- hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP1));
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-#if defined(RTC_TAMPCR_TAMP2E)
- if ((Tamper & RTC_TAMPER_2) != 0U)
- {
- hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP2));
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-#if defined(RTC_TAMPCR_TAMP3E)
- if ((Tamper & RTC_TAMPER_3) != 0U)
- {
- hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP3));
- }
-#endif /* RTC_TAMPCR_TAMP3E */
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-#endif /* RTC_TAMPCR_TAMP1E */
-
-#if defined(TAMP_CR1_ITAMP1E)
-/**
- * @brief Set Internal Tamper
- * @param hrtc RTC handle
- * @param sIntTamper Pointer to Internal Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper)
-{
- /* Check the parameters */
- assert_param(IS_RTC_INTERNAL_TAMPER(sIntTamper->IntTamper));
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sIntTamper->TimeStampOnTamperDetection));
-
- /* Time-Stamp on internal tamper */
- if (READ_BIT(RTC->CR, RTC_CR_TAMPTS) != sIntTamper->TimeStampOnTamperDetection)
- {
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
- MODIFY_REG(RTC->CR, RTC_CR_TAMPTS, sIntTamper->TimeStampOnTamperDetection);
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
- }
-
- /* Control register 1 */
- SET_BIT(TAMP->CR1, sIntTamper->IntTamper);
-
- return HAL_OK;
-}
-
-/**
- * @brief Set Internal Tamper in interrupt mode
- * @param hrtc RTC handle
- * @param sIntTamper Pointer to Internal Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper_IT(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper)
-{
- /* Check the parameters */
- assert_param(IS_RTC_INTERNAL_TAMPER(sIntTamper->IntTamper));
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sIntTamper->TimeStampOnTamperDetection));
-
- /* Time-stamp on internal tamper */
- if (READ_BIT(RTC->CR, RTC_CR_TAMPTS) != sIntTamper->TimeStampOnTamperDetection)
- {
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
- MODIFY_REG(RTC->CR, RTC_CR_TAMPTS, sIntTamper->TimeStampOnTamperDetection);
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
- }
-
- /* RTC Tamper Interrupt Configuration: EXTI configuration */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_FALLING_EDGE();
- /* Interrupt enable register */
- SET_BIT(TAMP->IER, sIntTamper->IntTamper);
-
- /* Control register 1 */
- SET_BIT(TAMP->CR1, sIntTamper->IntTamper);
-
- return HAL_OK;
-}
-
-/**
- * @brief Deactivate Internal Tamper.
- * @param hrtc RTC handle
- * @param IntTamper Selected internal tamper event.
- * This parameter can be any combination of existing internal tampers.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTamper(RTC_HandleTypeDef *hrtc, uint32_t IntTamper)
-{
- UNUSED(hrtc);
- assert_param(IS_RTC_INTERNAL_TAMPER(IntTamper));
-
- /* Disable the selected Tamper pin */
- CLEAR_BIT(TAMP->CR1, IntTamper);
-
- /* Clear internal tamper interrupt mode configuration */
- CLEAR_BIT(TAMP->IER, IntTamper);
-
- /* Clear internal tamper interrupt */
- WRITE_REG(TAMP->SCR, IntTamper);
-
- return HAL_OK;
-}
-#endif /* TAMP_CR1_ITAMP1E */
-
-#if defined(TAMP_ATCR1_TAMP1AM)
-/**
- * @brief Set all active Tampers at the same time.
- * @param hrtc RTC handle
- * @param sAllTamper Pointer to active Tamper Structure.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetActiveTampers(RTC_HandleTypeDef *hrtc, RTC_ActiveTampersTypeDef *sAllTamper)
-{
- uint32_t IER, CR1, CR2, ATCR1, CR, i, tickstart;
-
-#ifdef USE_FULL_ASSERT
- for (i = 0; i < RTC_TAMP_NB; i++)
- {
- assert_param(IS_RTC_TAMPER_ERASE_MODE(sAllTamper->TampInput[i].NoErase));
- assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sAllTamper->TampInput[i].MaskFlag));
- /* Mask flag only supported by TAMPER 1, 2 and 3 */
- assert_param(!((sAllTamper->TampInput[i].MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) && (i > RTC_TAMPER_3)));
- }
- assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sAllTamper->TimeStampOnTamperDetection));
-#endif /* #ifdef USE_FULL_ASSERT */
-
- /* Active Tampers must not be already enabled */
- if (READ_BIT(TAMP->ATOR, TAMP_ATOR_INITS) != 0U)
- {
- /* Disable all actives tampers with HAL_RTCEx_DeactivateActiveTampers and try again */
- return HAL_ERROR;
- }
-
- /* Set TimeStamp on tamper detection */
- CR = READ_REG(RTC->CR);
- if ((CR & RTC_CR_TAMPTS) != (sAllTamper->TimeStampOnTamperDetection))
- {
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
- MODIFY_REG(RTC->CR, RTC_CR_TAMPTS, sAllTamper->TimeStampOnTamperDetection);
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
- }
-
- CR1 = READ_REG(TAMP->CR1);
- CR2 = READ_REG(TAMP->CR2);
- IER = READ_REG(TAMP->IER);
-
- /* Set common parameters */
- ATCR1 = (sAllTamper->ActiveFilter | (sAllTamper->ActiveOutputChangePeriod << TAMP_ATCR1_ATPER_Pos) | sAllTamper->ActiveAsyncPrescaler);
-
- /* Set specific parameters for each active tamper inputs if enable */
- for (i = 0; i < RTC_TAMP_NB; i++)
- {
- if (sAllTamper->TampInput[i].Enable != RTC_ATAMP_DISABLE)
- {
- CR1 |= (TAMP_CR1_TAMP1E << i);
- ATCR1 |= (TAMP_ATCR1_TAMP1AM << i);
-
- if (sAllTamper->TampInput[i].Interrupt != RTC_ATAMP_INTERRUPT_DISABLE)
- {
- /* RTC Tamper Interrupt Configuration: EXTI configuration */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT();
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE();
-
- /* Interrupt enable register */
- IER |= (TAMP_IER_TAMP1IE << i);
- }
-
- if (sAllTamper->TampInput[i].MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE)
- {
- CR2 |= (TAMP_CR2_TAMP1MSK << i);
- }
-
- if (sAllTamper->TampInput[i].NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE)
- {
- CR2 |= (TAMP_CR2_TAMP1NOERASE << i);
- }
-
- /* Set ATOSHARE and configure ATOSELx[] in case of output sharing */
- if (sAllTamper->TampInput[i].Output != i)
- {
- ATCR1 |= TAMP_ATCR1_ATOSHARE;
- ATCR1 |= sAllTamper->TampInput[i].Output << ((2u * i) + TAMP_ATCR1_ATOSEL1_Pos);
- }
- }
- }
-
- WRITE_REG(TAMP->IER, IER);
- WRITE_REG(TAMP->IER, IER);
- WRITE_REG(TAMP->ATCR1, ATCR1);
-#if defined(TAMP_ATCR2_ATOSEL1)
- WRITE_REG(TAMP->ATCR2, ATCR2);
-#endif /* TAMP_ATCR2_ATOSEL1 */
- WRITE_REG(TAMP->CR2, CR2);
- WRITE_REG(TAMP->CR1, CR1);
-
- /* Write seed */
- for (i = 0; i < RTC_ATAMP_SEED_NB_UINT32; i++)
- {
- WRITE_REG(TAMP->ATSEEDR, sAllTamper->Seed[i]);
- }
-
- /* Wait till RTC SEEDF flag is set and if Time out is reached exit */
- tickstart = HAL_GetTick();
- while (READ_BIT(TAMP->ATOR, TAMP_ATOR_SEEDF) != 0u)
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
-
- return HAL_OK;
-}
-#endif /* TAMP_ATCR1_TAMP1AM */
-
-#if defined(TAMP_ATSEEDR_SEED)
-/**
- * @brief Write a new seed. Active tamper must be enabled.
- * @param hrtc RTC handle
- * @param pSeed Pointer to active tamper seed values.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetActiveSeed(RTC_HandleTypeDef *hrtc, uint32_t *pSeed)
-{
- uint32_t i, tickstart;
-
- /* Active Tampers must be enabled */
- if (READ_BIT(TAMP->ATOR, TAMP_ATOR_INITS) == 0U)
- {
- return HAL_ERROR;
- }
-
- for (i = 0; i < RTC_ATAMP_SEED_NB_UINT32; i++)
- {
- WRITE_REG(TAMP->ATSEEDR, pSeed[i]);
- }
-
- /* Wait till RTC SEEDF flag is set and if Time out is reached exit */
- tickstart = HAL_GetTick();
- while (READ_BIT(TAMP->ATOR, TAMP_ATOR_SEEDF) != 0U)
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
-
- return HAL_OK;
-}
-#endif /* TAMP_ATSEEDR_SEED */
-
-#if defined(TAMP_ATCR1_TAMP1AM)
-/**
- * @brief Deactivate all Active Tampers at the same time.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateActiveTampers(RTC_HandleTypeDef *hrtc)
-{
- /* Get Active tampers */
- uint32_t ATamp_mask = READ_BIT(TAMP->ATCR1, TAMP_ALL);
-
- UNUSED(hrtc);
- /* Disable all actives tampers but not passives tampers */
- CLEAR_BIT(TAMP->CR1, ATamp_mask);
- /* Disable no erase and mask */
- CLEAR_BIT(TAMP->CR2, (ATamp_mask | ((ATamp_mask & (TAMP_ATCR1_TAMP1AM | TAMP_ATCR1_TAMP2AM | TAMP_ATCR1_TAMP3AM)) << TAMP_CR2_TAMP1MSK_Pos)));
-
- /* Clear tamper interrupt and event flags (WO register) of all actives tampers but not passives tampers */
- WRITE_REG(TAMP->SCR, ATamp_mask);
-
- /* Clear all active tampers interrupt mode configuration but not passives tampers */
- CLEAR_BIT(TAMP->IER, ATamp_mask);
-
- CLEAR_BIT(TAMP->ATCR1, TAMP_ALL | TAMP_ATCR1_ATCKSEL | TAMP_ATCR1_ATPER | \
- TAMP_ATCR1_ATOSHARE | TAMP_ATCR1_FLTEN);
-
-#if defined(TAMP_ATCR2_ATOSEL1)
- CLEAR_BIT(TAMP->ATCR2, TAMP_ATCR2_ATOSEL1 | TAMP_ATCR2_ATOSEL2 | TAMP_ATCR2_ATOSEL3 | TAMP_ATCR2_ATOSEL4 |
- TAMP_ATCR2_ATOSEL5 | TAMP_ATCR2_ATOSEL6 | TAMP_ATCR2_ATOSEL7 | TAMP_ATCR2_ATOSEL8);
-#endif /* TAMP_ATCR2_ATOSEL1 */
-
- return HAL_OK;
-}
-#endif /* TAMP_ATCR1_TAMP1AM */
-
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group1
- * @brief RTC TimeStamp and Tamper functions
- *
-* @{
-*/
-
-/**
- * @brief Handle TimeStamp interrupt request.
- * @param hrtc RTC handle
- * @retval None
- */
-#if defined(RTC_MISR_TSMF)
-void HAL_RTCEx_TamperTimeStampIRQHandler(RTC_HandleTypeDef *hrtc)
-{
-
- /* Point on TAMPER registers base address */
- TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET);
-
- /* Clear the EXTI's Flag for RTC TimeStamp and Tamper */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG();
-
- if ((hrtc->Instance->MISR & RTC_MISR_TSMF) != 0u)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call TimeStampEvent registered Callback */
- hrtc->TimeStampEventCallback(hrtc);
-#else
- HAL_RTCEx_TimeStampEventCallback(hrtc);
-#endif
- /* Not immediately clear flags because the content of RTC_TSTR and RTC_TSDR are cleared when TSF bit is reset.*/
- hrtc->Instance->SCR = RTC_SCR_CTSF;
- }
-
- /* Get interrupt status */
- uint32_t tmp = tamp->MISR;
-
- /* Immediately clear flags */
- tamp->SCR = tmp;
-
-#if defined(TAMP_CR1_TAMP1E)
- /* Check Tamper1 status */
- if ((tmp & RTC_TAMPER_1) == RTC_TAMPER_1)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Tamper 1 Event registered Callback */
- hrtc->Tamper1EventCallback(hrtc);
-#else
- /* Tamper1 callback */
- HAL_RTCEx_Tamper1EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_TAMP1E */
-
-#if defined(TAMP_CR1_TAMP2E)
- /* Check Tamper2 status */
- if ((tmp & RTC_TAMPER_2) == RTC_TAMPER_2)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Tamper 2 Event registered Callback */
- hrtc->Tamper2EventCallback(hrtc);
-#else
- /* Tamper2 callback */
- HAL_RTCEx_Tamper2EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_TAMP2E */
-
-#if defined(TAMP_CR1_TAMP3E)
- /* Check Tamper3 status */
- if ((tmp & RTC_TAMPER_3) == RTC_TAMPER_3)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Tamper 3 Event registered Callback */
- hrtc->Tamper3EventCallback(hrtc);
-#else
- /* Tamper3 callback */
- HAL_RTCEx_Tamper3EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_TAMP3E */
-
-#if defined(TAMP_CR1_ITAMP1E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_1) == RTC_INT_TAMPER_1)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper1EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper1EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP1E */
-
-#if defined(TAMP_CR1_ITAMP2E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_2) == RTC_INT_TAMPER_2)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper2EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper2EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP2E */
-
-#if defined(TAMP_CR1_ITAMP3E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_3) == RTC_INT_TAMPER_3)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper3EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper3EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP3E */
-
-#if defined(TAMP_CR1_ITAMP4E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_4) == RTC_INT_TAMPER_4)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper4EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper4EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP4E */
-
-#if defined(TAMP_CR1_ITAMP5E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_5) == RTC_INT_TAMPER_5)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper5EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper5EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP5E */
-
-#if defined(TAMP_CR1_ITAMP6E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_6) == RTC_INT_TAMPER_6)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper6EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper6EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP6E */
-
-#if defined(TAMP_CR1_ITAMP8E)
- /* Check Internal Tamper status */
- if ((tmp & RTC_INT_TAMPER_8) == RTC_INT_TAMPER_8)
- {
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call Internal Tamper Event registered callback */
- hrtc->InternalTamper8EventCallback(hrtc);
-#else
- /* Call Internal Tamper Event by-default callback */
- HAL_RTCEx_InternalTamper8EventCallback(hrtc);
-#endif
- }
-#endif /* TAMP_CR1_ITAMP8E */
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-}
-#endif /* RTC_MISR_TSMF */
-#if defined(RTC_ISR_TSF)
-void HAL_RTCEx_TamperTimeStampIRQHandler(RTC_HandleTypeDef *hrtc)
-{
- /* Clear the EXTI's Flag for RTC TimeStamp and Tamper */
-#if defined(DUAL_CORE)
- if (HAL_GetCurrentCPUID() == CM7_CPUID)
- {
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG();
- }
- else
- {
- __HAL_RTC_TAMPER_TIMESTAMP_EXTID2_CLEAR_FLAG();
- }
-#else /* SINGLE_CORE */
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG();
-#endif /* DUAL_CORE */
-
- /* Get the TimeStamp interrupt source enable status */
- if (__HAL_RTC_TIMESTAMP_GET_IT_SOURCE(hrtc, RTC_IT_TS) != 0U)
- {
- /* Get the pending status of the TIMESTAMP Interrupt */
- if (__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) != 0U)
- {
- /* TIMESTAMP callback */
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- hrtc->TimeStampEventCallback(hrtc);
-#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- HAL_RTCEx_TimeStampEventCallback(hrtc);
-#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
-
- /* Clear the TIMESTAMP interrupt pending bit (this will clear timestamp time and date registers) */
- __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF);
- }
- }
-
-#if defined(RTC_TAMPCR_TAMP1E)
- /* Get the Tamper1 interrupt source enable status */
- if (__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP | RTC_IT_TAMP1) != 0U)
- {
- /* Get the pending status of the Tamper1 Interrupt */
- if (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F) != 0U)
- {
- /* Clear the Tamper1 interrupt pending bit */
- __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP1F);
-
- /* Tamper1 callback */
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- hrtc->Tamper1EventCallback(hrtc);
-#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- HAL_RTCEx_Tamper1EventCallback(hrtc);
-#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- }
- }
-#endif /* RTC_TAMPCR_TAMP1E */
-
-#if defined(RTC_TAMPCR_TAMP2E)
- /* Get the Tamper2 interrupt source enable status */
- if (__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP | RTC_IT_TAMP2) != 0U)
- {
- /* Get the pending status of the Tamper2 Interrupt */
- if (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F) != 0U)
- {
- /* Clear the Tamper2 interrupt pending bit */
- __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP2F);
-
- /* Tamper2 callback */
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- hrtc->Tamper2EventCallback(hrtc);
-#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- HAL_RTCEx_Tamper2EventCallback(hrtc);
-#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- }
- }
-#endif /* RTC_TAMPCR_TAMP2E */
-
-#if defined(RTC_TAMPCR_TAMP3E)
- /* Get the Tamper3 interrupts source enable status */
- if (__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP | RTC_IT_TAMP3) != 0U)
- {
- /* Get the pending status of the Tamper3 Interrupt */
- if (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP3F) != 0U)
- {
- /* Clear the Tamper3 interrupt pending bit */
- __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP3F);
-
- /* Tamper3 callback */
-#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- hrtc->Tamper3EventCallback(hrtc);
-#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- HAL_RTCEx_Tamper3EventCallback(hrtc);
-#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */
- }
- }
-#endif /* RTC_TAMPCR_TAMP3E */
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-}
-#endif /* RTC_ISR_TSF */
-
-/**
- * @brief TimeStamp callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_TimeStampEventCallback could be implemented in the user file
- */
-}
-
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group5
- * @brief Extended RTC Tamper functions
- *
-* @{
-*/
-
-#if defined(RTC_TAMPER_1)
-/**
- * @brief Tamper 1 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef * hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_Tamper1EventCallback could be implemented in the user file
- */
-}
-#endif /* RTC_TAMPER_1 */
-
-#if defined(RTC_TAMPER_2)
-/**
- * @brief Tamper 2 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef * hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_Tamper2EventCallback could be implemented in the user file
- */
-}
-#endif /* RTC_TAMPER_2 */
-
-#if defined(RTC_TAMPER_3)
-/**
- * @brief Tamper 3 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef * hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_Tamper3EventCallback could be implemented in the user file
- */
-}
-#endif /* RTC_TAMPER_3 */
-
-/**
- * @brief Internal Tamper 1 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper1EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper1EventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Internal Tamper 2 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper2EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper2EventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Internal Tamper 3 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper3EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper3EventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Internal Tamper 4 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper4EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper4EventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Internal Tamper 5 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper5EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper5EventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Internal Tamper 6 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper6EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper6EventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Internal Tamper 8 callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_InternalTamper8EventCallback(RTC_HandleTypeDef *hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_InternalTamper8EventCallback could be implemented in the user file
- */
-}
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group1
- * @brief RTC TimeStamp and Tamper functions
- *
-* @{
-*/
-
-/**
- * @brief Handle TimeStamp polling request.
- * @param hrtc RTC handle
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- while (__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) == 0U)
- {
- if (__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSOVF) != 0U)
- {
- /* Clear the TIMESTAMP OverRun Flag */
- __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSOVF);
-
- /* Change TIMESTAMP state */
- hrtc->State = HAL_RTC_STATE_ERROR;
-
- return HAL_ERROR;
- }
-
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group5
- * @brief Extended RTC Tamper functions
- *
-* @{
-*/
-
-#if defined(RTC_TAMPER_1)
-/**
- * @brief Handle Tamper1 Polling.
- * @param hrtc RTC handle
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForTamper1Event(RTC_HandleTypeDef * hrtc, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- /* Get the status of the Interrupt */
- while (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F) == 0U)
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Clear the Tamper Flag */
- __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP1F);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- return HAL_OK;
-}
-#endif /* RTC_TAMPER_1 */
-
-#if defined(RTC_TAMPER_2)
-/**
- * @brief Handle Tamper2 Polling.
- * @param hrtc RTC handle
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForTamper2Event(RTC_HandleTypeDef * hrtc, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- /* Get the status of the Interrupt */
- while (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F) == 0U)
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Clear the Tamper Flag */
- __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP2F);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- return HAL_OK;
-}
-#endif /* RTC_TAMPER_2 */
-
-#if defined(RTC_TAMPER_3)
-/**
- * @brief Handle Tamper3 Polling.
- * @param hrtc RTC handle
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForTamper3Event(RTC_HandleTypeDef * hrtc, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- /* Get the status of the Interrupt */
- while (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP3F) == 0U)
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Clear the Tamper Flag */
- __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP3F);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- return HAL_OK;
-}
-#endif /* RTC_TAMPER_3 */
-
-#if defined(TAMP_CR1_ITAMP1E)
-/**
- * @brief Internal Tamper event polling.
- * @param hrtc RTC handle
- * @param IntTamper selected tamper.
- * This parameter can be any combination of existing internal tampers.
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForInternalTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t IntTamper, uint32_t Timeout)
-{
- UNUSED(hrtc);
- assert_param(IS_RTC_INTERNAL_TAMPER(IntTamper));
-
- uint32_t tickstart = HAL_GetTick();
-
- /* Get the status of the Interrupt */
- while (READ_BIT(TAMP->SR, IntTamper) != IntTamper)
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Clear the Tamper Flag */
- WRITE_REG(TAMP->SCR, IntTamper);
-
- return HAL_OK;
-}
-#endif /* TAMP_CR1_ITAMP1E */
-
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group2
- * @brief RTC Wake-up functions
- *
-@verbatim
- ===============================================================================
- ##### RTC Wake-up functions #####
- ===============================================================================
-
- [..] This section provides functions allowing to configure Wake-up feature
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Set wake up timer.
- * @param hrtc RTC handle
- * @param WakeUpCounter Wake up counter
- * @param WakeUpClock Wake up clock
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock)
-{
- uint32_t tickstart;
-
- /* Check the parameters */
- assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock));
- assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Check RTC WUTWF flag is reset only when wake up timer enabled */
- if ((hrtc->Instance->CR & RTC_CR_WUTE) != 0U)
- {
- tickstart = HAL_GetTick();
-
- /* Wait till RTC WUTWF flag is reset and if Time out is reached exit */
- #if defined(RTC_ICSR_WUTWF)
- while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) != 0U)
- #endif /* RTC_ICSR_WUTWF */
- #if defined(RTC_ISR_WUTWF)
- while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) != 0U)
- #endif /* RTC_ISR_WUTWF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
- }
-
- __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc);
-
- tickstart = HAL_GetTick();
-
- /* Wait till RTC WUTWF flag is set and if Time out is reached exit */
- #if defined(RTC_ICSR_WUTWF)
- while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) == 0U)
- #endif /* RTC_ICSR_WUTWF */
- #if defined(RTC_ISR_WUTWF)
- while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U)
- #endif /* RTC_ISR_WUTWF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
-
- /* Clear the Wakeup Timer clock source bits and configure the clock source in CR register */
- {
- uint32_t CR_tmp = hrtc->Instance->CR;
- CR_tmp &= (uint32_t)~RTC_CR_WUCKSEL;
- CR_tmp |= (uint32_t)WakeUpClock;
- hrtc->Instance->CR = CR_tmp;
- }
-
- /* Configure the Wakeup Timer counter */
- hrtc->Instance->WUTR = (uint32_t)WakeUpCounter;
-
- /* Enable the Wakeup Timer */
- __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Set wake up timer with interrupt.
- * @param hrtc RTC handle
- * @param WakeUpCounter Wake up counter
- * @param WakeUpClock Wake up clock
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock)
-{
- uint32_t tickstart;
-
- /* Check the parameters */
- assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock));
- assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Check RTC WUTWF flag is reset only when wake up timer enabled */
- if ((hrtc->Instance->CR & RTC_CR_WUTE) != 0U)
- {
- tickstart = HAL_GetTick();
-
- /* Wait till RTC WUTWF flag is reset and if Time out is reached exit */
- #if defined(RTC_ICSR_WUTWF)
- while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) != 0U)
- #endif /* RTC_ICSR_WUTWF */
- #if defined(RTC_ISR_WUTWF)
- while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) != 0U)
- #endif /* RTC_ISR_WUTWF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
- }
- /* Disable the Wake-Up timer */
- __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc);
-
- /* Clear flag Wake-Up */
- __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF);
-
- tickstart = HAL_GetTick();
-
- /* Wait till RTC WUTWF flag is set and if Time out is reached exit */
- #if defined(RTC_ICSR_WUTWF)
- while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) == 0U)
- #endif /* RTC_ICSR_WUTWF */
- #if defined(RTC_ISR_WUTWF)
- while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U)
- #endif /* RTC_ISR_WUTWF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
-
- /* Configure the Wakeup Timer counter */
- hrtc->Instance->WUTR = (uint32_t)WakeUpCounter;
-
- /* Clear the Wakeup Timer clock source bits and configure the clock source in CR register */
- {
- uint32_t CR_tmp = hrtc->Instance->CR;
- CR_tmp &= (uint32_t)~RTC_CR_WUCKSEL;
- CR_tmp |= (uint32_t)WakeUpClock;
- hrtc->Instance->CR = CR_tmp;
- }
-
-#if !defined(DUAL_CORE)
- /* RTC WakeUpTimer Interrupt Configuration: EXTI configuration */
- __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT();
-#endif
-
- __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_RISING_EDGE();
-
- /* Configure the Interrupt in the RTC_CR register */
- __HAL_RTC_WAKEUPTIMER_ENABLE_IT(hrtc, RTC_IT_WUT);
-
- /* Enable the Wakeup Timer */
- __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Deactivate wake up timer counter.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc)
-{
- uint32_t tickstart;
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Disable the Wakeup Timer */
- __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc);
-
- /* In case of interrupt mode is used, the interrupt source must disabled */
- __HAL_RTC_WAKEUPTIMER_DISABLE_IT(hrtc, RTC_IT_WUT);
-
- tickstart = HAL_GetTick();
- /* Wait till RTC WUTWF flag is set and if Time out is reached exit */
- #if defined(RTC_ICSR_WUTWF)
- while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) == 0U)
- #endif /* RTC_ICSR_WUTWF */
- #if defined(RTC_ISR_WUTWF)
- while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U)
- #endif /* RTC_ISR_WUTWF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Get wake up timer counter.
- * @param hrtc RTC handle
- * @retval Counter value
- */
-uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc)
-{
- /* Get the counter value */
- return ((uint32_t)(hrtc->Instance->WUTR & RTC_WUTR_WUT));
-}
-
-/**
- * @brief Handle Wake Up Timer interrupt request.
- * @param hrtc RTC handle
- * @retval None
- */
-void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc)
-{
- /* Clear the EXTI's line Flag for RTC WakeUpTimer */
-#if defined(DUAL_CORE)
- if (HAL_GetCurrentCPUID() == CM7_CPUID)
- {
- __HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG();
- }
- else
- {
- __HAL_RTC_WAKEUPTIMER_EXTID2_CLEAR_FLAG();
- }
-#else /* SINGLE_CORE */
- __HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG();
-#endif /* DUAL_CORE */
-
-#if defined(RTC_MISR_WUTMF)
- /* Get the pending status of the WAKEUPTIMER Interrupt */
- if ((hrtc->Instance->MISR & RTC_MISR_WUTMF) != 0u)
- {
- /* Immediately clear flags */
- hrtc->Instance->SCR = RTC_SCR_CWUTF;
-
- /* WAKEUPTIMER callback */
- #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call WakeUpTimerEvent registered Callback */
- hrtc->WakeUpTimerEventCallback(hrtc);
- #else
- HAL_RTCEx_WakeUpTimerEventCallback(hrtc);
- #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
- }
-#endif /* RTC_MISR_WUTMF */
-#if defined(RTC_ISR_WUTF)
- /* Get the pending status of the WAKEUPTIMER Interrupt */
- if (__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) != 0U)
- {
- /* Clear the WAKEUPTIMER interrupt pending bit */
- __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF);
-
- /* WAKEUPTIMER callback */
- #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
- /* Call WakeUpTimerEvent registered Callback */
- hrtc->WakeUpTimerEventCallback(hrtc);
- #else
- HAL_RTCEx_WakeUpTimerEventCallback(hrtc);
- #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
- }
-#endif /* RTC_ISR_WUTF */
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-}
-
-/**
- * @brief Wake Up Timer callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef * hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_WakeUpTimerEventCallback could be implemented in the user file
- */
-}
-
-
-/**
- * @brief Handle Wake Up Timer Polling.
- * @param hrtc RTC handle
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef * hrtc, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) == 0U)
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Clear the WAKEUPTIMER Flag */
- __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-
-/** @addtogroup RTCEx_Exported_Functions_Group6
- * @brief Extended RTC Backup register functions
- *
-@verbatim
- ===============================================================================
- ##### Extended RTC Backup register functions #####
- ===============================================================================
- [..]
- (+) Before calling any tamper or internal tamper function, you have to call first
- HAL_RTC_Init() function.
- (+) In that ine you can select to output tamper event on RTC pin.
- [..]
- This subsection provides functions allowing to
- (+) Write a data in a specified RTC Backup data register
- (+) Read a data in a specified RTC Backup data register
-@endverbatim
- * @{
- */
-
-
-/**
- * @brief Write a data in a specified RTC Backup data register.
- * @param hrtc RTC handle
- * @param BackupRegister RTC Backup data Register number.
- * This parameter can be: RTC_BKP_DRx where x can be from 0 to 31 to
- * specify the register.
- * @param Data Data to be written in the specified Backup data register.
- * @retval None
- */
-void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef * hrtc, uint32_t BackupRegister, uint32_t Data)
-{
- uint32_t tmp;
-
- /* Check the parameters */
- assert_param(IS_RTC_BKP(BackupRegister));
-
- /* Point on address of first backup register */
-#if defined(TAMP_BKP0R)
- tmp = (uint32_t) & (((TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET))->BKP0R);
-#endif /* TAMP_BKP0R */
-#if defined(RTC_BKP0R)
- tmp = (uint32_t) & (hrtc->Instance->BKP0R);
-#endif /* RTC_BKP0R */
-
- tmp += (BackupRegister * 4U);
-
- /* Write the specified register */
- *(__IO uint32_t *)tmp = (uint32_t)Data;
-}
-
-
-/**
- * @brief Read data from the specified RTC Backup data Register.
- * @param hrtc RTC handle
- * @param BackupRegister RTC Backup data Register number.
- * This parameter can be: RTC_BKP_DRx where x can be from 0 to 31 to
- * specify the register.
- * @retval Read value
- */
-uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef * hrtc, uint32_t BackupRegister)
-{
- uint32_t tmp;
-
- /* Check the parameters */
- assert_param(IS_RTC_BKP(BackupRegister));
-
- /* Point on address of first backup register */
-#if defined(TAMP_BKP0R)
- tmp = (uint32_t) & (((TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET))->BKP0R);
-#endif /* TAMP_BKP0R */
-#if defined(RTC_BKP0R)
- tmp = (uint32_t) & (hrtc->Instance->BKP0R);
-#endif /* RTC_BKP0R */
-
- tmp += (BackupRegister * 4U);
-
- /* Read the specified register */
- return (*(__IO uint32_t *)tmp);
-}
-
-
-/**
- * @}
- */
-
-
-/** @addtogroup RTCEx_Exported_Functions_Group3
- * @brief Extended Peripheral Control functions
- *
-@verbatim
- ===============================================================================
- ##### Extended Peripheral Control functions #####
- ===============================================================================
- [..]
- This subsection provides functions allowing to
- (+) Write a data in a specified RTC Backup data register
- (+) Read a data in a specified RTC Backup data register
- (+) Set the Smooth calibration parameters.
- (+) Set Low Power calibration parameter (if feature supported).
- (+) Configure the Synchronization Shift Control Settings.
- (+) Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
- (+) Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
- (+) Enable the RTC reference clock detection.
- (+) Disable the RTC reference clock detection.
- (+) Enable the Bypass Shadow feature.
- (+) Disable the Bypass Shadow feature.
-
-@endverbatim
- * @{
- */
-
-
-/**
- * @brief Set the Smooth calibration parameters.
- * @param hrtc RTC handle
- * @param SmoothCalibPeriod Select the Smooth Calibration Period.
- * This parameter can be can be one of the following values :
- * @arg RTC_SMOOTHCALIB_PERIOD_32SEC: The smooth calibration period is 32s.
- * @arg RTC_SMOOTHCALIB_PERIOD_16SEC: The smooth calibration period is 16s.
- * @arg RTC_SMOOTHCALIB_PERIOD_8SEC: The smooth calibration period is 8s.
- * @param SmoothCalibPlusPulses Select to Set or reset the CALP bit.
- * This parameter can be one of the following values:
- * @arg RTC_SMOOTHCALIB_PLUSPULSES_SET: Add one RTCCLK pulse every 2*11 pulses.
- * @arg RTC_SMOOTHCALIB_PLUSPULSES_RESET: No RTCCLK pulses are added.
- * @param SmoothCalibMinusPulsesValue Select the value of CALM[8:0] bits.
- * This parameter can be one any value from 0 to 0x000001FF.
- * @note To deactivate the smooth calibration, the field SmoothCalibPlusPulses
- * must be equal to SMOOTHCALIB_PLUSPULSES_RESET and the field
- * SmoothCalibMinusPulsesValue must be equal to 0.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef * hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue)
-{
- uint32_t tickstart;
-
- /* Check the parameters */
- assert_param(IS_RTC_SMOOTH_CALIB_PERIOD(SmoothCalibPeriod));
- assert_param(IS_RTC_SMOOTH_CALIB_PLUS(SmoothCalibPlusPulses));
- assert_param(IS_RTC_SMOOTH_CALIB_MINUS(SmoothCalibMinusPulsesValue));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* check if a calibration operation is pending */
-#if defined(RTC_ICSR_RECALPF)
- if ((hrtc->Instance->ICSR & RTC_ICSR_RECALPF) != 0U)
-#endif /* RTC_ICSR_RECALPF */
-#if defined(RTC_ISR_RECALPF)
- if ((hrtc->Instance->ISR & RTC_ISR_RECALPF) != 0U)
-#endif /* RTC_ISR_RECALPF */
- {
- tickstart = HAL_GetTick();
-
- /* Wait for pending calibration operation to finish */
-#if defined(RTC_ICSR_RECALPF)
- while ((hrtc->Instance->ICSR & RTC_ICSR_RECALPF) != 0U)
-#endif /* RTC_ICSR_RECALPF */
-#if defined(RTC_ISR_RECALPF)
- while ((hrtc->Instance->ISR & RTC_ISR_RECALPF) != 0U)
-#endif /* RTC_ISR_RECALPF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Configure the Smooth calibration settings */
- MODIFY_REG(hrtc->Instance->CALR, (RTC_CALR_CALP | RTC_CALR_CALW8 | RTC_CALR_CALW16 | RTC_CALR_CALM), (uint32_t)(SmoothCalibPeriod | SmoothCalibPlusPulses | SmoothCalibMinusPulsesValue));
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Configure the Synchronization Shift Control Settings.
- * @note When REFCKON is set, firmware must not write to Shift control register.
- * @param hrtc RTC handle
- * @param ShiftAdd1S Select to add or not 1 second to the time calendar.
- * This parameter can be one of the following values:
- * @arg RTC_SHIFTADD1S_SET: Add one second to the clock calendar.
- * @arg RTC_SHIFTADD1S_RESET: No effect.
- * @param ShiftSubFS Select the number of Second Fractions to substitute.
- * This parameter can be one any value from 0 to 0x7FFF.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef * hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS)
-{
- uint32_t tickstart;
-
- /* Check the parameters */
- assert_param(IS_RTC_SHIFT_ADD1S(ShiftAdd1S));
- assert_param(IS_RTC_SHIFT_SUBFS(ShiftSubFS));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- tickstart = HAL_GetTick();
-
- /* Wait until the shift is completed */
-#if defined(RTC_ICSR_SHPF)
- while ((hrtc->Instance->ICSR & RTC_ICSR_SHPF) != 0U)
-#endif /* RTC_ICSR_SHPF */
-#if defined(RTC_ISR_SHPF)
- while ((hrtc->Instance->ISR & RTC_ISR_SHPF) != 0U)
-#endif /* RTC_ISR_SHPF */
- {
- if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_TIMEOUT;
- }
- }
-
- /* Check if the reference clock detection is disabled */
- if ((hrtc->Instance->CR & RTC_CR_REFCKON) == 0U)
- {
- /* Configure the Shift settings */
- hrtc->Instance->SHIFTR = (uint32_t)(uint32_t)(ShiftSubFS) | (uint32_t)(ShiftAdd1S);
-
- /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
- if ((hrtc->Instance->CR & RTC_CR_BYPSHAD) == 0U)
- {
- if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- hrtc->State = HAL_RTC_STATE_ERROR;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_ERROR;
- }
- }
- }
- else
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_ERROR;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_ERROR;
- }
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
- * @param hrtc RTC handle
- * @param CalibOutput Select the Calibration output Selection.
- * This parameter can be one of the following values:
- * @arg RTC_CALIBOUTPUT_512HZ: A signal has a regular waveform at 512Hz.
- * @arg RTC_CALIBOUTPUT_1HZ: A signal has a regular waveform at 1Hz.
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef * hrtc, uint32_t CalibOutput)
-{
- /* Check the parameters */
- assert_param(IS_RTC_CALIB_OUTPUT(CalibOutput));
-
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Clear flags before config */
- hrtc->Instance->CR &= (uint32_t)~RTC_CR_COSEL;
-
- /* Configure the RTC_CR register */
- hrtc->Instance->CR |= (uint32_t)CalibOutput;
-
- __HAL_RTC_CALIBRATION_OUTPUT_ENABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz).
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef * hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- __HAL_RTC_CALIBRATION_OUTPUT_DISABLE(hrtc);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Enable the RTC reference clock detection.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef * hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Set Initialization mode */
- if (RTC_EnterInitMode(hrtc) != HAL_OK)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Set RTC state*/
- hrtc->State = HAL_RTC_STATE_ERROR;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_ERROR;
- }
- else
- {
- __HAL_RTC_CLOCKREF_DETECTION_ENABLE(hrtc);
-
- /* Exit Initialization mode */
-#if defined(RTC_ICSR_INIT)
- hrtc->Instance->ICSR &= (uint32_t)~RTC_ICSR_INIT;
-#endif /* RTC_ICSR_INIT */
-#if defined(RTC_ISR_INIT)
- hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
-#endif /* RTC_ISR_INIT */
- }
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Disable the RTC reference clock detection.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef * hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Set Initialization mode */
- if (RTC_EnterInitMode(hrtc) != HAL_OK)
- {
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Set RTC state*/
- hrtc->State = HAL_RTC_STATE_ERROR;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_ERROR;
- }
- else
- {
- __HAL_RTC_CLOCKREF_DETECTION_DISABLE(hrtc);
-
- /* Exit Initialization mode */
-#if defined(RTC_ICSR_INIT)
- hrtc->Instance->ICSR &= (uint32_t)~RTC_ICSR_INIT;
-#endif /* RTC_ICSR_INIT */
-#if defined(RTC_ISR_INIT)
- hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;
-#endif /* RTC_ISR_INIT */
- }
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Enable the Bypass Shadow feature.
- * @note When the Bypass Shadow is enabled the calendar value are taken
- * directly from the Calendar counter.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef * hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Set the BYPSHAD bit */
- hrtc->Instance->CR |= (uint8_t)RTC_CR_BYPSHAD;
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-/**
- * @brief Disable the Bypass Shadow feature.
- * @note When the Bypass Shadow is enabled the calendar value are taken
- * directly from the Calendar counter.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef * hrtc)
-{
- /* Process Locked */
- __HAL_LOCK(hrtc);
-
- hrtc->State = HAL_RTC_STATE_BUSY;
-
- /* Disable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
-
- /* Reset the BYPSHAD bit */
- hrtc->Instance->CR &= ((uint8_t)~RTC_CR_BYPSHAD);
-
- /* Enable the write protection for RTC registers */
- __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- /* Process Unlocked */
- __HAL_UNLOCK(hrtc);
-
- return HAL_OK;
-}
-
-#if defined(TAMP_COUNTR)
-/**
- * @brief Increment Monotonic counter.
- * @param hrtc RTC handle
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterIncrement(RTC_HandleTypeDef *hrtc)
-{
- UNUSED(hrtc);
- /* This register is read-only only and is incremented by one when a write access is done to this
- register. This register cannot roll-over and is frozen when reaching the maximum value. */
- CLEAR_REG(TAMP->COUNTR);
-
- return HAL_OK;
-}
-
-/**
- * @brief Monotonic counter incrementation.
- * @param hrtc RTC handle
- * @param Counter monotonic counter value
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterGet(RTC_HandleTypeDef *hrtc, uint32_t *Counter)
-{
- UNUSED(hrtc);
- /* This register is read-only only and is incremented by one when a write access is done to this
- register. This register cannot roll-over and is frozen when reaching the maximum value. */
- *Counter = READ_REG(TAMP->COUNTR);
-
- return HAL_OK;
-}
-#endif /* TAMP_COUNTR */
-
-/**
- * @}
- */
-
-/** @addtogroup RTCEx_Exported_Functions_Group4
- * @brief Extended features functions
- *
-@verbatim
- ===============================================================================
- ##### Extended features functions #####
- ===============================================================================
- [..] This section provides functions allowing to:
- (+) RTC Alarm B callback
- (+) RTC Poll for Alarm B request
-
-@endverbatim
- * @{
- */
-
-/**
- * @brief Alarm B callback.
- * @param hrtc RTC handle
- * @retval None
- */
-__weak void HAL_RTCEx_AlarmBEventCallback(RTC_HandleTypeDef * hrtc)
-{
- /* Prevent unused argument(s) compilation warning */
- UNUSED(hrtc);
-
- /* NOTE : This function should not be modified, when the callback is needed,
- the HAL_RTCEx_AlarmBEventCallback could be implemented in the user file
- */
-}
-
-/**
- * @brief Handle Alarm B Polling request.
- * @param hrtc RTC handle
- * @param Timeout Timeout duration
- * @retval HAL status
- */
-HAL_StatusTypeDef HAL_RTCEx_PollForAlarmBEvent(RTC_HandleTypeDef * hrtc, uint32_t Timeout)
-{
- uint32_t tickstart = HAL_GetTick();
-
- while (__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBF) == 0U)
- {
- if (Timeout != HAL_MAX_DELAY)
- {
- if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
- {
- hrtc->State = HAL_RTC_STATE_TIMEOUT;
- return HAL_TIMEOUT;
- }
- }
- }
-
- /* Clear the Alarm Flag */
- __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF);
-
- /* Change RTC state */
- hrtc->State = HAL_RTC_STATE_READY;
-
- return HAL_OK;
-}
-
-/**
- * @}
- */
-
-
-/**
- * @}
- */
-
-#endif /* HAL_RTC_MODULE_ENABLED */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+/** + ****************************************************************************** + * @file stm32h7xx_hal_rtc_ex.c + * @author MCD Application Team + * @brief Extended RTC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Real Time Clock (RTC) Extended peripheral: + * + RTC Time Stamp functions + * + RTC Tamper functions + * + RTC Wake-up functions + * + Extended Control functions + * + Extended RTC features functions + * + ****************************************************************************** + * @attention + * + * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + (+) Enable the RTC domain access. + (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour + format using the HAL_RTC_Init() function. + + *** RTC Wakeup configuration *** + ================================ + [..] + (+) To configure the RTC Wakeup Clock source and Counter use the HAL_RTCEx_SetWakeUpTimer() + function. You can also configure the RTC Wakeup timer with interrupt mode + using the HAL_RTCEx_SetWakeUpTimer_IT() function. + (+) To read the RTC WakeUp Counter register, use the HAL_RTCEx_GetWakeUpTimer() + function. + + *** Outputs configuration *** + ============================= + [..] The RTC has 2 different outputs: + (+) RTC_ALARM: this output is used to manage the RTC Alarm A, Alarm B + and WaKeUp signals. + To output the selected RTC signal, use the HAL_RTC_Init() function. + (+) RTC_CALIB: this output is 512Hz signal or 1Hz. + To enable the RTC_CALIB, use the HAL_RTCEx_SetCalibrationOutPut() function. + (+) Two pins can be used as RTC_ALARM or RTC_CALIB (PC13, PB2) managed on + the RTC_OR register. + (+) When the RTC_CALIB or RTC_ALARM output is selected, the RTC_OUT pin is + automatically configured in output alternate function. + + *** Smooth digital Calibration configuration *** + ================================================ + [..] + (+) Configure the RTC Original Digital Calibration Value and the corresponding + calibration cycle period (32s,16s and 8s) using the HAL_RTCEx_SetSmoothCalib() + function. + + *** TimeStamp configuration *** + =============================== + [..] + (+) Enable the RTC TimeStamp using the HAL_RTCEx_SetTimeStamp() function. + You can also configure the RTC TimeStamp with interrupt mode using the + HAL_RTCEx_SetTimeStamp_IT() function. + (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp() + function. + + *** Internal TimeStamp configuration *** + =============================== + [..] + (+) Enable the RTC internal TimeStamp using the HAL_RTCEx_SetInternalTimeStamp() function. + User has to check internal timestamp occurrence using __HAL_RTC_INTERNAL_TIMESTAMP_GET_FLAG. + (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTCEx_GetTimeStamp() + function. + + *** Tamper configuration *** + ============================ + [..] + (+) Enable the RTC Tamper and configure the Tamper filter count, trigger Edge + or Level according to the Tamper filter (if equal to 0 Edge else Level) + value, sampling frequency, NoErase, MaskFlag, precharge or discharge and + Pull-UP using the HAL_RTCEx_SetTamper() function. You can configure RTC Tamper + with interrupt mode using HAL_RTCEx_SetTamper_IT() function. + (+) The default configuration of the Tamper erases the backup registers. To avoid + erase, enable the NoErase field on the RTC_TAMPCR register. + + *** Backup Data Registers configuration *** + =========================================== + [..] + (+) To write to the RTC Backup Data registers, use the HAL_RTCEx_BKUPWrite() + function. + (+) To read the RTC Backup Data registers, use the HAL_RTCEx_BKUPRead() + function. + + @endverbatim + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32h7xx_hal.h" + +/** @addtogroup STM32H7xx_HAL_Driver + * @{ + */ + +/** @addtogroup RTCEx + * @brief RTC Extended HAL module driver + * @{ + */ + +#ifdef HAL_RTC_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define TAMP_ALL (TAMP_CR1_TAMP1E | TAMP_CR1_TAMP2E | TAMP_CR1_TAMP3E) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ + +/** @addtogroup RTCEx_Exported_Functions + * @{ + */ + + +/** @addtogroup RTCEx_Exported_Functions_Group1 + * @brief RTC TimeStamp and Tamper functions + * +@verbatim + =============================================================================== + ##### RTC TimeStamp and Tamper functions ##### + =============================================================================== + + [..] This section provides functions allowing to configure TimeStamp feature + +@endverbatim + * @{ + */ + +/** + * @brief Set TimeStamp. + * @note This API must be called before enabling the TimeStamp feature. + * @param hrtc RTC handle + * @param TimeStampEdge Specifies the pin edge on which the TimeStamp is + * activated. + * This parameter can be one of the following values: + * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the + * rising edge of the related pin. + * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the + * falling edge of the related pin. + * @param RTC_TimeStampPin specifies the RTC TimeStamp Pin. + * This parameter can be one of the following values: + * @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin. + * The RTC TimeStamp Pin is per default PC13, but for reasons of + * compatibility, this parameter is required. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin) +{ + uint32_t tmpreg; + + /* Check the parameters */ + assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge)); + assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin)); + + /* Prevent unused argument(s) compilation warning if no assert_param check */ + UNUSED(RTC_TimeStampPin); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Get the RTC_CR register and clear the bits to be configured */ + tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); + + tmpreg |= TimeStampEdge; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Configure the Time Stamp TSEDGE and Enable bits */ + hrtc->Instance->CR = (uint32_t)tmpreg; + + __HAL_RTC_TIMESTAMP_ENABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Set TimeStamp with Interrupt. + * @note This API must be called before enabling the TimeStamp feature. + * @param hrtc RTC handle + * @param TimeStampEdge Specifies the pin edge on which the TimeStamp is + * activated. + * This parameter can be one of the following values: + * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the + * rising edge of the related pin. + * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the + * falling edge of the related pin. + * @param RTC_TimeStampPin Specifies the RTC TimeStamp Pin. + * This parameter can be one of the following values: + * @arg RTC_TIMESTAMPPIN_DEFAULT: PC13 is selected as RTC TimeStamp Pin. + * The RTC TimeStamp Pin is per default PC13, but for reasons of + * compatibility, this parameter is required. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin) +{ + uint32_t tmpreg; + + /* Check the parameters */ + assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge)); + assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin)); + + /* Prevent unused argument(s) compilation warning if no assert_param check */ + UNUSED(RTC_TimeStampPin); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Get the RTC_CR register and clear the bits to be configured */ + tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); + + tmpreg |= TimeStampEdge; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Configure the Time Stamp TSEDGE and Enable bits */ + hrtc->Instance->CR = (uint32_t)tmpreg; + + __HAL_RTC_TIMESTAMP_ENABLE(hrtc); + + /* Enable IT timestamp */ + __HAL_RTC_TIMESTAMP_ENABLE_IT(hrtc, RTC_IT_TS); + + /* RTC timestamp Interrupt Configuration: EXTI configuration */ +#if defined(DUAL_CORE) + if (HAL_GetCurrentCPUID() == CM7_CPUID) + { + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); + } + else + { + __HAL_RTC_TAMPER_TIMESTAMP_EXTID2_ENABLE_IT(); + } +#else /* SINGLE_CORE */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); +#endif /* DUAL_CORE */ + + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE(); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Deactivate TimeStamp. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc) +{ + uint32_t tmpreg; + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* In case of interrupt mode is used, the interrupt source must disabled */ + __HAL_RTC_TIMESTAMP_DISABLE_IT(hrtc, RTC_IT_TS); + + /* Get the RTC_CR register and clear the bits to be configured */ + tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); + + /* Configure the Time Stamp TSEDGE and Enable bits */ + hrtc->Instance->CR = (uint32_t)tmpreg; + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Set Internal TimeStamp. + * @note This API must be called before enabling the internal TimeStamp feature. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetInternalTimeStamp(RTC_HandleTypeDef *hrtc) +{ + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Configure the internal Time Stamp Enable bits */ + __HAL_RTC_INTERNAL_TIMESTAMP_ENABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Deactivate Internal TimeStamp. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTimeStamp(RTC_HandleTypeDef *hrtc) +{ + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Configure the internal Time Stamp Enable bits */ + __HAL_RTC_INTERNAL_TIMESTAMP_DISABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Get the RTC TimeStamp value. + * @param hrtc RTC handle + * @param sTimeStamp Pointer to Time structure + * @param sTimeStampDate Pointer to Date structure + * @param Format specifies the format of the entered parameters. + * This parameter can be one of the following values: + * @arg RTC_FORMAT_BIN: Binary data format + * @arg RTC_FORMAT_BCD: BCD data format + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTimeStamp, RTC_DateTypeDef *sTimeStampDate, uint32_t Format) +{ + uint32_t tmptime; + uint32_t tmpdate; + + /* Check the parameters */ + assert_param(IS_RTC_FORMAT(Format)); + + /* Get the TimeStamp time and date registers values */ + tmptime = (uint32_t)(hrtc->Instance->TSTR & RTC_TR_RESERVED_MASK); + tmpdate = (uint32_t)(hrtc->Instance->TSDR & RTC_DR_RESERVED_MASK); + + /* Fill the Time structure fields with the read parameters */ + sTimeStamp->Hours = (uint8_t)((tmptime & (RTC_TSTR_HT | RTC_TSTR_HU)) >> RTC_TSTR_HU_Pos); + sTimeStamp->Minutes = (uint8_t)((tmptime & (RTC_TSTR_MNT | RTC_TSTR_MNU)) >> RTC_TSTR_MNU_Pos); + sTimeStamp->Seconds = (uint8_t)((tmptime & (RTC_TSTR_ST | RTC_TSTR_SU)) >> RTC_TSTR_SU_Pos); + sTimeStamp->TimeFormat = (uint8_t)((tmptime & (RTC_TSTR_PM)) >> RTC_TSTR_PM_Pos); + sTimeStamp->SubSeconds = (uint32_t) hrtc->Instance->TSSSR; + + /* Fill the Date structure fields with the read parameters */ + sTimeStampDate->Year = 0U; + sTimeStampDate->Month = (uint8_t)((tmpdate & (RTC_TSDR_MT | RTC_TSDR_MU)) >> RTC_TSDR_MU_Pos); + sTimeStampDate->Date = (uint8_t)((tmpdate & (RTC_TSDR_DT | RTC_TSDR_DU)) >> RTC_TSDR_DU_Pos); + sTimeStampDate->WeekDay = (uint8_t)((tmpdate & (RTC_TSDR_WDU)) >> RTC_TSDR_WDU_Pos); + + /* Check the input parameters format */ + if (Format == RTC_FORMAT_BIN) + { + /* Convert the TimeStamp structure parameters to Binary format */ + sTimeStamp->Hours = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Hours); + sTimeStamp->Minutes = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Minutes); + sTimeStamp->Seconds = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Seconds); + + /* Convert the DateTimeStamp structure parameters to Binary format */ + sTimeStampDate->Month = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Month); + sTimeStampDate->Date = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Date); + sTimeStampDate->WeekDay = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->WeekDay); + } + + /* Clear the TIMESTAMP Flags */ + __HAL_RTC_INTERNAL_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_ITSF); + __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF); + + return HAL_OK; +} + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group5 + * @brief Extended RTC Tamper functions + * +@verbatim + ============================================================================== + ##### Tamper functions ##### + ============================================================================== + [..] + (+) Before calling any tamper or internal tamper function, you have to call first + HAL_RTC_Init() function. + (+) In that ine you can select to output tamper event on RTC pin. + [..] + (+) Enable the Tamper and configure the Tamper filter count, trigger Edge + or Level according to the Tamper filter (if equal to 0 Edge else Level) + value, sampling frequency, NoErase, MaskFlag, precharge or discharge and + Pull-UP, timestamp using the HAL_RTCEx_SetTamper() function. + You can configure Tamper with interrupt mode using HAL_RTCEx_SetTamper_IT() function. + (+) The default configuration of the Tamper erases the backup registers. To avoid + erase, enable the NoErase field on the TAMP_TAMPCR register. + [..] + (+) Enable Internal Tamper and configure it with interrupt, timestamp using + the HAL_RTCEx_SetInternalTamper() function. + +@endverbatim +* @{ +*/ + +#if defined(TAMP) +/** + * @brief Set Tamper + * @param hrtc RTC handle + * @param sTamper Pointer to Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper) +{ + uint32_t tmpreg; + + /* Point on TAMPER registers base address */ + TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET); + + /* Check the parameters */ + assert_param(IS_RTC_TAMPER(sTamper->Tamper)); + assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); + assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); + assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); + assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); + assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); + assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); + assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); + assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger)); + + /* Configuration register 2 */ + tmpreg = tamp->CR2; + tmpreg &= ~((sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos)); + + /* Configure the tamper trigger bit */ + if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE)) + { + tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos); + } + + /* Configure the tamper flags masking bit */ + if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) + { + tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos); + } + + /* Configure the tamper backup registers erasure bit */ + if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) + { + tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos); + } + tamp->CR2 = tmpreg; + + /* Configure filtering parameters */ + tamp->FLTCR = (sTamper->Filter) | (sTamper->SamplingFrequency) | \ + (sTamper->PrechargeDuration) | (sTamper->TamperPullUp); + + /* Configure Timestamp saving on tamper detection */ + if ((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sTamper->TimeStampOnTamperDetection)) + { + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS); + hrtc->Instance->CR = (tmpreg | (sTamper->TimeStampOnTamperDetection)); + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + } + + /* Enable selected tamper */ + tamp->CR1 |= (sTamper->Tamper); + + return HAL_OK; +} +#else +/** + * @brief Set Tamper. + * @note By calling this API we disable the tamper interrupt for all tampers. + * @param hrtc RTC handle + * @param sTamper Pointer to Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper) +{ + uint32_t tmpreg; + + /* Check the parameters */ + assert_param(IS_RTC_TAMPER(sTamper->Tamper)); + assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); + assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); + assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); + assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); + assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); + assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); + assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); + assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Copy control register into temporary variable */ + tmpreg = hrtc->Instance->TAMPCR; + + /* Enable selected tamper */ + tmpreg |= (sTamper->Tamper); + + /* Configure the bit (located just next to the tamper enable bit) */ + if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE)) + { + /* Set the tamper trigger bit */ + tmpreg |= (uint32_t)(sTamper->Tamper << 1U); + } + else + { + /* Clear the tamper trigger bit */ + tmpreg &= (uint32_t)~(sTamper->Tamper << 1U); + } + + /* Configure the tamper backup registers erasure bit */ + if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3NOERASE); + } + } + else + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3NOERASE); + } + } + + /* Configure the tamper flags masking bit */ + if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1MF); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2MF); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3MF); + } + } + else + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1MF); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2MF); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3MF); + } + } + + /* Clearing remaining fields before setting them */ + tmpreg &= ~(RTC_TAMPERFILTER_MASK | RTC_TAMPERSAMPLINGFREQ_RTCCLK_MASK | \ + RTC_TAMPERPRECHARGEDURATION_MASK | RTC_TAMPER_PULLUP_MASK | \ + RTC_TIMESTAMPONTAMPERDETECTION_MASK); + + /* Set remaining parameters of desired configuration into temporary variable */ + tmpreg |= ((uint32_t)sTamper->Filter | \ + (uint32_t)sTamper->SamplingFrequency | \ + (uint32_t)sTamper->PrechargeDuration | \ + (uint32_t)sTamper->TamperPullUp | \ + (uint32_t)sTamper->TimeStampOnTamperDetection); + + /* Copy desired configuration into configuration register */ + hrtc->Instance->TAMPCR = tmpreg; + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} +#endif /* TAMP */ + +#if defined(TAMP) +/** + * @brief Set Tamper with interrupt. + * @param hrtc RTC handle + * @param sTamper Pointer to Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper) +{ + uint32_t tmpreg; + + /* Point on TAMPER registers base address */ + TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET); + + /* Check the parameters */ + assert_param(IS_RTC_TAMPER(sTamper->Tamper)); + assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); + assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); + assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); + assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); + assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); + assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); + assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); + assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger)); + + /* Copy configuration register into temporary variable */ + tmpreg = tamp->CR2; + + /* Clear the bits that are going to be configured and leave the others unchanged */ + tmpreg &= ~((sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos) | (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos)); + + /* Configure the tamper trigger bit */ + if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE)) + { + tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1TRG_Pos); + } + + /* Configure the tamper flags masking bit */ + if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) + { + tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1MSK_Pos); + } + + /* Configure the tamper backup registers erasure bit */ + if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) + { + tmpreg |= (sTamper->Tamper << TAMP_CR2_TAMP1NOERASE_Pos); + } + tamp->CR2 = tmpreg; + + /* Configure filtering parameters */ + tamp->FLTCR = (sTamper->Filter) | (sTamper->SamplingFrequency) | \ + (sTamper->PrechargeDuration) | (sTamper->TamperPullUp); + + /* Configure Timestamp saving on tamper detection */ + if ((hrtc->Instance->CR & RTC_CR_TAMPTS) != (sTamper->TimeStampOnTamperDetection)) + { + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + tmpreg = (hrtc->Instance->CR & ~RTC_CR_TAMPTS); + hrtc->Instance->CR = (tmpreg | (sTamper->TimeStampOnTamperDetection)); + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + } + + /* Configure RTC Tamper Interrupt: EXTI configuration */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_FALLING_EDGE(); + + /* Enable interrupt on selected tamper */ + tamp->IER |= sTamper->Tamper; + + /* Enable selected tamper */ + tamp->CR1 |= sTamper->Tamper; + + return HAL_OK; +} +#else +/** + * @brief Set Tamper with interrupt. + * @note By calling this API we force the tamper interrupt for all tampers. + * @param hrtc RTC handle + * @param sTamper Pointer to Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef * hrtc, RTC_TamperTypeDef * sTamper) +{ + uint32_t tmpreg; + + /* Check the parameters */ + assert_param(IS_RTC_TAMPER(sTamper->Tamper)); + assert_param(IS_RTC_TAMPER_INTERRUPT(sTamper->Interrupt)); + assert_param(IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); + assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); + assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); + assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); + assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); + assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); + assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); + assert_param(IS_RTC_TAMPER_FILTER_CONFIG_CORRECT(sTamper->Filter, sTamper->Trigger)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Copy control register into temporary variable */ + tmpreg = hrtc->Instance->TAMPCR; + + /* Enable selected tamper */ + tmpreg |= (sTamper->Tamper); + + /* Configure the tamper trigger bit (located just next to the tamper enable bit) */ + if ((sTamper->Trigger == RTC_TAMPERTRIGGER_HIGHLEVEL) || (sTamper->Trigger == RTC_TAMPERTRIGGER_FALLINGEDGE)) + { + /* Set the tamper trigger bit */ + tmpreg |= (uint32_t)(sTamper->Tamper << 1U); + } + else + { + /* Clear the tamper trigger bit */ + tmpreg &= (uint32_t)~(sTamper->Tamper << 1U); + } + + /* Configure the tamper backup registers erasure bit */ + if (sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3NOERASE); + } + } + else + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2NOERASE); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3NOERASE); + } + } + + /* Configure the tamper flags masking bit */ + if (sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP1MF); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP2MF); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg |= (uint32_t)(RTC_TAMPCR_TAMP3MF); + } + } + else + { + if ((sTamper->Tamper & RTC_TAMPER_1) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP1MF); + } + if ((sTamper->Tamper & RTC_TAMPER_2) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP2MF); + } + if ((sTamper->Tamper & RTC_TAMPER_3) != 0U) + { + tmpreg &= (uint32_t)~(RTC_TAMPCR_TAMP3MF); + } + } + + /* Clearing remaining fields before setting them */ + tmpreg &= ~(RTC_TAMPERFILTER_MASK | RTC_TAMPERSAMPLINGFREQ_RTCCLK_MASK | \ + RTC_TAMPERPRECHARGEDURATION_MASK | RTC_TAMPER_PULLUP_MASK | \ + RTC_TIMESTAMPONTAMPERDETECTION_MASK); + + /* Set remaining parameters of desired configuration into temporary variable */ + tmpreg |= ((uint32_t)sTamper->Filter | \ + (uint32_t)sTamper->SamplingFrequency | \ + (uint32_t)sTamper->PrechargeDuration | \ + (uint32_t)sTamper->TamperPullUp | \ + (uint32_t)sTamper->TimeStampOnTamperDetection); + + /* Enable interrupt on selected tamper */ + tmpreg |= (uint32_t)sTamper->Interrupt; + + /* Copy desired configuration into configuration register */ + hrtc->Instance->TAMPCR = tmpreg; + + /* RTC Tamper Interrupt Configuration: EXTI configuration */ +#if defined(DUAL_CORE) + if (HAL_GetCurrentCPUID() == CM7_CPUID) + { + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); + } + else + { + __HAL_RTC_TAMPER_TIMESTAMP_EXTID2_ENABLE_IT(); + } +#else /* SINGLE_CORE */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); +#endif /* DUAL_CORE */ + + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE(); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} +#endif /* TAMP */ + +#if defined(TAMP) +/** + * @brief Deactivate Tamper. + * @param hrtc RTC handle + * @param Tamper Selected tamper pin. + * This parameter can be a combination of the following values: + * @arg RTC_TAMPER_1 + * @arg RTC_TAMPER_2 + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef * hrtc, uint32_t Tamper) +{ + /* Point on TAMPER registers base address */ + TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET); + + assert_param(IS_RTC_TAMPER(Tamper)); + + /* Disable the selected Tamper pin */ + tamp->CR1 &= ~Tamper; + + /* Disable the selected Tamper interrupt */ + tamp->IER &= ~Tamper; + + /* Clear the selected tamper flags in SR register by setting corresponding bits in SCR register */ + tamp->SCR = Tamper; + + /* Clear the selected tamper configuration (trigger, mask flag, and no-erase) */ + tamp->CR2 &= ~((Tamper << TAMP_CR2_TAMP1TRG_Pos) | (Tamper << TAMP_CR2_TAMP1MSK_Pos) | (Tamper << TAMP_CR2_TAMP1NOERASE_Pos)); + + return HAL_OK; +} +#else +/** + * @brief Deactivate Tamper. + * @param hrtc RTC handle + * @param Tamper Selected tamper pin. + * This parameter can be any combination of the following values: + * @arg RTC_TAMPER_1 + * @arg RTC_TAMPER_2 + * @arg RTC_TAMPER_3 + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef * hrtc, uint32_t Tamper) +{ + assert_param(IS_RTC_TAMPER(Tamper)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the selected Tamper pin */ + hrtc->Instance->TAMPCR &= ((uint32_t)~Tamper); + + /* Disable the selected Tamper interrupt */ + if ((Tamper & RTC_TAMPER_1) != 0U) + { + hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP1)); + } + + if ((Tamper & RTC_TAMPER_2) != 0U) + { + hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP2)); + } + + if ((Tamper & RTC_TAMPER_3) != 0U) + { + hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP3)); + } + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} +#endif /* TAMP */ + +#if defined(TAMP) +/** + * @brief Set Internal Tamper + * @param hrtc RTC handle + * @param sIntTamper Pointer to Internal Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper) +{ + /* Check the parameters */ + assert_param(IS_RTC_INTERNAL_TAMPER(sIntTamper->IntTamper)); + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sIntTamper->TimeStampOnTamperDetection)); + + /* Time-Stamp on internal tamper */ + if (READ_BIT(RTC->CR, RTC_CR_TAMPTS) != sIntTamper->TimeStampOnTamperDetection) + { + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + MODIFY_REG(RTC->CR, RTC_CR_TAMPTS, sIntTamper->TimeStampOnTamperDetection); + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + } + + /* Control register 1 */ + SET_BIT(TAMP->CR1, sIntTamper->IntTamper); + + return HAL_OK; +} + +/** + * @brief Set Internal Tamper in interrupt mode + * @param hrtc RTC handle + * @param sIntTamper Pointer to Internal Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetInternalTamper_IT(RTC_HandleTypeDef *hrtc, RTC_InternalTamperTypeDef *sIntTamper) +{ + /* Check the parameters */ + assert_param(IS_RTC_INTERNAL_TAMPER(sIntTamper->IntTamper)); + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sIntTamper->TimeStampOnTamperDetection)); + + /* Time-stamp on internal tamper */ + if (READ_BIT(RTC->CR, RTC_CR_TAMPTS) != sIntTamper->TimeStampOnTamperDetection) + { + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + MODIFY_REG(RTC->CR, RTC_CR_TAMPTS, sIntTamper->TimeStampOnTamperDetection); + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + } + + /* RTC Tamper Interrupt Configuration: EXTI configuration */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_FALLING_EDGE(); + /* Interrupt enable register */ + SET_BIT(TAMP->IER, sIntTamper->IntTamper); + + /* Control register 1 */ + SET_BIT(TAMP->CR1, sIntTamper->IntTamper); + + return HAL_OK; +} + +/** + * @brief Deactivate Internal Tamper. + * @param hrtc RTC handle + * @param IntTamper Selected internal tamper event. + * This parameter can be any combination of existing internal tampers. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateInternalTamper(RTC_HandleTypeDef *hrtc, uint32_t IntTamper) +{ + UNUSED(hrtc); + assert_param(IS_RTC_INTERNAL_TAMPER(IntTamper)); + + /* Disable the selected Tamper pin */ + CLEAR_BIT(TAMP->CR1, IntTamper); + + /* Clear internal tamper interrupt mode configuration */ + CLEAR_BIT(TAMP->IER, IntTamper); + + /* Clear internal tamper interrupt */ + WRITE_REG(TAMP->SCR, IntTamper); + + return HAL_OK; +} + +/** + * @brief Set all active Tampers at the same time. + * @param hrtc RTC handle + * @param sAllTamper Pointer to active Tamper Structure. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetActiveTampers(RTC_HandleTypeDef *hrtc, RTC_ActiveTampersTypeDef *sAllTamper) +{ + uint32_t IER, CR1, CR2, ATCR1, CR, i, tickstart; + +#ifdef USE_FULL_ASSERT + for (i = 0; i < RTC_TAMP_NB; i++) + { + assert_param(IS_RTC_TAMPER_ERASE_MODE(sAllTamper->TampInput[i].NoErase)); + assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sAllTamper->TampInput[i].MaskFlag)); + /* Mask flag only supported by TAMPER 1, 2, and 3 */ + assert_param(!((sAllTamper->TampInput[i].MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) && (i > RTC_TAMPER_3))); + } + + assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sAllTamper->TimeStampOnTamperDetection)); +#endif /* USE_FULL_ASSERT */ + + /* Active Tampers must not be already enabled */ + if (READ_BIT(TAMP->ATOR, TAMP_ATOR_INITS) != 0U) + { + /* Disable all active tampers with HAL_RTCEx_DeactivateActiveTampers */ + if (HAL_RTCEx_DeactivateActiveTampers(hrtc) != HAL_OK) + { + return HAL_ERROR; + } + } + + /* Set TimeStamp on tamper detection */ + CR = READ_REG(RTC->CR); + if ((CR & RTC_CR_TAMPTS) != (sAllTamper->TimeStampOnTamperDetection)) + { + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + MODIFY_REG(RTC->CR, RTC_CR_TAMPTS, sAllTamper->TimeStampOnTamperDetection); + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + } + + CR1 = READ_REG(TAMP->CR1); + CR2 = READ_REG(TAMP->CR2); + IER = READ_REG(TAMP->IER); + + /* Set common parameters */ + ATCR1 = (sAllTamper->ActiveFilter | (sAllTamper->ActiveOutputChangePeriod << TAMP_ATCR1_ATPER_Pos) | sAllTamper->ActiveAsyncPrescaler); + + /* Set specific parameters for each active tamper inputs if enable */ + for (i = 0; i < RTC_TAMP_NB; i++) + { + if (sAllTamper->TampInput[i].Enable != RTC_ATAMP_DISABLE) + { + CR1 |= (TAMP_CR1_TAMP1E << i); + ATCR1 |= (TAMP_ATCR1_TAMP1AM << i); + + if (sAllTamper->TampInput[i].Interrupt != RTC_ATAMP_INTERRUPT_DISABLE) + { + /* RTC Tamper Interrupt Configuration: EXTI configuration */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE(); + + /* Interrupt enable register */ + IER |= (TAMP_IER_TAMP1IE << i); + } + + if (sAllTamper->TampInput[i].MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) + { + CR2 |= (TAMP_CR2_TAMP1MSK << i); + } + + if (sAllTamper->TampInput[i].NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) + { + CR2 |= (TAMP_CR2_TAMP1NOERASE << i); + } + + /* Set ATOSHARE and configure ATOSELx[] in case of output sharing */ + if (sAllTamper->TampInput[i].Output != i) + { + ATCR1 |= TAMP_ATCR1_ATOSHARE; + ATCR1 |= sAllTamper->TampInput[i].Output << ((2u * i) + TAMP_ATCR1_ATOSEL1_Pos); + } + } + } + + WRITE_REG(TAMP->IER, IER); + WRITE_REG(TAMP->IER, IER); + WRITE_REG(TAMP->ATCR1, ATCR1); +#if defined(TAMP_ATCR2_ATOSEL1) + WRITE_REG(TAMP->ATCR2, ATCR2); +#endif /* TAMP_ATCR2_ATOSEL1 */ + WRITE_REG(TAMP->CR2, CR2); + WRITE_REG(TAMP->CR1, CR1); + + /* Write seed */ + for (i = 0; i < RTC_ATAMP_SEED_NB_UINT32; i++) + { + WRITE_REG(TAMP->ATSEEDR, sAllTamper->Seed[i]); + } + + /* Wait till RTC SEEDF flag is set and if timeout is reached exit */ + tickstart = HAL_GetTick(); + while (READ_BIT(TAMP->ATOR, TAMP_ATOR_SEEDF) != 0u) + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + + return HAL_OK; +} + +/** + * @brief Write a new seed. Active tamper must be enabled. + * @param hrtc RTC handle + * @param pSeed Pointer to active tamper seed values. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetActiveSeed(RTC_HandleTypeDef *hrtc, uint32_t *pSeed) +{ + uint32_t i, tickstart; + + /* Active Tampers must be enabled */ + if (READ_BIT(TAMP->ATOR, TAMP_ATOR_INITS) == 0U) + { + return HAL_ERROR; + } + + for (i = 0; i < RTC_ATAMP_SEED_NB_UINT32; i++) + { + WRITE_REG(TAMP->ATSEEDR, pSeed[i]); + } + + /* Wait till RTC SEEDF flag is set and if timeout is reached exit */ + tickstart = HAL_GetTick(); + while (READ_BIT(TAMP->ATOR, TAMP_ATOR_SEEDF) != 0U) + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + + return HAL_OK; +} + +/** + * @brief Deactivate all Active Tampers at the same time. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateActiveTampers(RTC_HandleTypeDef *hrtc) +{ + /* Get Active tampers */ + uint32_t ATamp_mask = READ_BIT(TAMP->ATCR1, TAMP_ALL); + + UNUSED(hrtc); + /* Disable all actives tampers but not passives tampers */ + CLEAR_BIT(TAMP->CR1, ATamp_mask); + /* Disable no erase and mask */ + CLEAR_BIT(TAMP->CR2, (ATamp_mask | ((ATamp_mask & (TAMP_ATCR1_TAMP1AM | TAMP_ATCR1_TAMP2AM | TAMP_ATCR1_TAMP3AM)) << TAMP_CR2_TAMP1MSK_Pos))); + + /* Clear tamper interrupt and event flags (WO register) of all actives tampers but not passives tampers */ + WRITE_REG(TAMP->SCR, ATamp_mask); + + /* Clear all active tampers interrupt mode configuration but not passives tampers */ + CLEAR_BIT(TAMP->IER, ATamp_mask); + + CLEAR_BIT(TAMP->ATCR1, TAMP_ALL | TAMP_ATCR1_ATCKSEL | TAMP_ATCR1_ATPER | \ + TAMP_ATCR1_ATOSHARE | TAMP_ATCR1_FLTEN); + +#if defined(TAMP_ATCR2_ATOSEL1) + CLEAR_BIT(TAMP->ATCR2, TAMP_ATCR2_ATOSEL1 | TAMP_ATCR2_ATOSEL2 | TAMP_ATCR2_ATOSEL3 | TAMP_ATCR2_ATOSEL4 | + TAMP_ATCR2_ATOSEL5 | TAMP_ATCR2_ATOSEL6 | TAMP_ATCR2_ATOSEL7 | TAMP_ATCR2_ATOSEL8); +#endif /* TAMP_ATCR2_ATOSEL1 */ + + return HAL_OK; +} +#endif /* TAMP */ + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group1 + * @brief RTC TimeStamp and Tamper functions + * +* @{ +*/ + +/** + * @brief Handle Tamper and TimeStamp interrupt request. + * @param hrtc RTC handle + * @retval None + */ +#if defined(TAMP) +void HAL_RTCEx_TamperTimeStampIRQHandler(RTC_HandleTypeDef *hrtc) +{ + + /* Point on TAMPER registers base address */ + TAMP_TypeDef *tamp = (TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET); + + /* Clear the EXTI's Flag for RTC TimeStamp and Tamper */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG(); + + if ((hrtc->Instance->MISR & RTC_MISR_TSMF) != 0u) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call TimeStampEvent registered Callback */ + hrtc->TimeStampEventCallback(hrtc); +#else + HAL_RTCEx_TimeStampEventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + /* Not immediately clear flags because the content of RTC_TSTR and RTC_TSDR are cleared when TSF bit is reset.*/ + hrtc->Instance->SCR = RTC_SCR_CTSF; + } + + /* Get interrupt status */ + uint32_t tmp = tamp->MISR; + + /* Immediately clear flags */ + tamp->SCR = tmp; + + /* Check Tamper 1 status */ + if ((tmp & RTC_TAMPER_1) == RTC_TAMPER_1) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Tamper 1 Event registered Callback */ + hrtc->Tamper1EventCallback(hrtc); +#else + /* Tamper 1 callback */ + HAL_RTCEx_Tamper1EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Tamper 2 status */ + if ((tmp & RTC_TAMPER_2) == RTC_TAMPER_2) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Tamper 2 Event registered Callback */ + hrtc->Tamper2EventCallback(hrtc); +#else + /* Tamper 2 callback */ + HAL_RTCEx_Tamper2EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Tamper 3 status */ + if ((tmp & RTC_TAMPER_3) == RTC_TAMPER_3) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Tamper 3 Event registered Callback */ + hrtc->Tamper3EventCallback(hrtc); +#else + /* Tamper 3 callback */ + HAL_RTCEx_Tamper3EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 1 status */ + if ((tmp & RTC_INT_TAMPER_1) == RTC_INT_TAMPER_1) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 1 Event registered callback */ + hrtc->InternalTamper1EventCallback(hrtc); +#else + /* Call Internal Tamper 1 Event by-default callback */ + HAL_RTCEx_InternalTamper1EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 2 status */ + if ((tmp & RTC_INT_TAMPER_2) == RTC_INT_TAMPER_2) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 2 Event registered callback */ + hrtc->InternalTamper2EventCallback(hrtc); +#else + /* Call Internal Tamper 2 Event by-default callback */ + HAL_RTCEx_InternalTamper2EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 3 status */ + if ((tmp & RTC_INT_TAMPER_3) == RTC_INT_TAMPER_3) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 3 Event registered callback */ + hrtc->InternalTamper3EventCallback(hrtc); +#else + /* Call Internal Tamper 3 Event by-default callback */ + HAL_RTCEx_InternalTamper3EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 4 status */ + if ((tmp & RTC_INT_TAMPER_4) == RTC_INT_TAMPER_4) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 4 Event registered callback */ + hrtc->InternalTamper4EventCallback(hrtc); +#else + /* Call Internal Tamper 4 Event by-default callback */ + HAL_RTCEx_InternalTamper4EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 5 status */ + if ((tmp & RTC_INT_TAMPER_5) == RTC_INT_TAMPER_5) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 5 Event registered callback */ + hrtc->InternalTamper5EventCallback(hrtc); +#else + /* Call Internal Tamper 5 Event by-default callback */ + HAL_RTCEx_InternalTamper5EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 6 status */ + if ((tmp & RTC_INT_TAMPER_6) == RTC_INT_TAMPER_6) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 6 Event registered callback */ + hrtc->InternalTamper6EventCallback(hrtc); +#else + /* Call Internal Tamper 6 Event by-default callback */ + HAL_RTCEx_InternalTamper6EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Check Internal Tamper 8 status */ + if ((tmp & RTC_INT_TAMPER_8) == RTC_INT_TAMPER_8) + { +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call Internal Tamper 8 Event registered callback */ + hrtc->InternalTamper8EventCallback(hrtc); +#else + /* Call Internal Tamper 8 Event by-default callback */ + HAL_RTCEx_InternalTamper8EventCallback(hrtc); +#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; +} +#else +void HAL_RTCEx_TamperTimeStampIRQHandler(RTC_HandleTypeDef *hrtc) +{ + /* Clear the EXTI's Flag for RTC TimeStamp and Tamper */ +#if defined(DUAL_CORE) + if (HAL_GetCurrentCPUID() == CM7_CPUID) + { + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG(); + } + else + { + __HAL_RTC_TAMPER_TIMESTAMP_EXTID2_CLEAR_FLAG(); + } +#else /* SINGLE_CORE */ + __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG(); +#endif /* DUAL_CORE */ + + /* Get the TimeStamp interrupt source enable status */ + if (__HAL_RTC_TIMESTAMP_GET_IT_SOURCE(hrtc, RTC_IT_TS) != 0U) + { + /* Get the pending status of the TIMESTAMP Interrupt */ + if (__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) != 0U) + { + /* TIMESTAMP callback */ +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + hrtc->TimeStampEventCallback(hrtc); +#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + HAL_RTCEx_TimeStampEventCallback(hrtc); +#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + + /* Clear the TIMESTAMP interrupt pending bit (this will clear timestamp time and date registers) */ + __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF); + } + } + + /* Get the Tamper 1 interrupt source enable status */ + if (__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP | RTC_IT_TAMP1) != 0U) + { + /* Get the pending status of the Tamper 1 Interrupt */ + if (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F) != 0U) + { + /* Clear the Tamper 1 interrupt pending bit */ + __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP1F); + + /* Tamper 1 callback */ +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + hrtc->Tamper1EventCallback(hrtc); +#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + HAL_RTCEx_Tamper1EventCallback(hrtc); +#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + } + } + + /* Get the Tamper 2 interrupt source enable status */ + if (__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP | RTC_IT_TAMP2) != 0U) + { + /* Get the pending status of the Tamper 2 Interrupt */ + if (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F) != 0U) + { + /* Clear the Tamper 2 interrupt pending bit */ + __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP2F); + + /* Tamper 2 callback */ +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + hrtc->Tamper2EventCallback(hrtc); +#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + HAL_RTCEx_Tamper2EventCallback(hrtc); +#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + } + } + + /* Get the Tamper 3 interrupts source enable status */ + if (__HAL_RTC_TAMPER_GET_IT_SOURCE(hrtc, RTC_IT_TAMP | RTC_IT_TAMP3) != 0U) + { + /* Get the pending status of the Tamper 3 Interrupt */ + if (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP3F) != 0U) + { + /* Clear the Tamper 3 interrupt pending bit */ + __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP3F); + + /* Tamper 3 callback */ +#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + hrtc->Tamper3EventCallback(hrtc); +#else /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + HAL_RTCEx_Tamper3EventCallback(hrtc); +#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS == 1) */ + } + } + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; +} +#endif /* TAMP */ + +/** + * @brief TimeStamp callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_TimeStampEventCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group5 + * @brief Extended RTC Tamper functions + * +* @{ +*/ + +/** + * @brief Tamper 1 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef * hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_Tamper1EventCallback could be implemented in the user file + */ +} + +/** + * @brief Tamper 2 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef * hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_Tamper2EventCallback could be implemented in the user file + */ +} + +/** + * @brief Tamper 3 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef * hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_Tamper3EventCallback could be implemented in the user file + */ +} + +#if defined(TAMP) +/** + * @brief Internal Tamper 1 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper1EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper1EventCallback could be implemented in the user file + */ +} + +/** + * @brief Internal Tamper 2 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper2EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper2EventCallback could be implemented in the user file + */ +} + +/** + * @brief Internal Tamper 3 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper3EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper3EventCallback could be implemented in the user file + */ +} + +/** + * @brief Internal Tamper 4 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper4EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper4EventCallback could be implemented in the user file + */ +} + +/** + * @brief Internal Tamper 5 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper5EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper5EventCallback could be implemented in the user file + */ +} + +/** + * @brief Internal Tamper 6 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper6EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper6EventCallback could be implemented in the user file + */ +} + +/** + * @brief Internal Tamper 8 callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_InternalTamper8EventCallback(RTC_HandleTypeDef *hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_InternalTamper8EventCallback could be implemented in the user file + */ +} +#endif /* TAMP */ + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group1 + * @brief RTC TimeStamp and Tamper functions + * +* @{ +*/ + +/** + * @brief Handle TimeStamp polling request. + * @param hrtc RTC handle + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + while (__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) == 0U) + { + if (__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSOVF) != 0U) + { + /* Clear the TIMESTAMP OverRun Flag */ + __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSOVF); + + /* Change TIMESTAMP state */ + hrtc->State = HAL_RTC_STATE_ERROR; + + return HAL_ERROR; + } + + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group5 + * @brief Extended RTC Tamper functions + * +* @{ +*/ + +/** + * @brief Handle Tamper1 Polling. + * @param hrtc RTC handle + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForTamper1Event(RTC_HandleTypeDef * hrtc, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + /* Get the status of the Interrupt */ + while (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F) == 0U) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Clear the Tamper Flag */ + __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP1F); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Handle Tamper2 Polling. + * @param hrtc RTC handle + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForTamper2Event(RTC_HandleTypeDef * hrtc, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + /* Get the status of the Interrupt */ + while (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F) == 0U) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Clear the Tamper Flag */ + __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP2F); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Handle Tamper3 Polling. + * @param hrtc RTC handle + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForTamper3Event(RTC_HandleTypeDef * hrtc, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + /* Get the status of the Interrupt */ + while (__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP3F) == 0U) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Clear the Tamper Flag */ + __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP3F); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +#if defined(TAMP) +/** + * @brief Internal Tamper event polling. + * @param hrtc RTC handle + * @param IntTamper selected tamper. + * This parameter can be any combination of existing internal tampers. + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForInternalTamperEvent(RTC_HandleTypeDef *hrtc, uint32_t IntTamper, uint32_t Timeout) +{ + UNUSED(hrtc); + assert_param(IS_RTC_INTERNAL_TAMPER(IntTamper)); + + uint32_t tickstart = HAL_GetTick(); + + /* Get the status of the Interrupt */ + while (READ_BIT(TAMP->SR, IntTamper) != IntTamper) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + return HAL_TIMEOUT; + } + } + } + + /* Clear the Tamper Flag */ + WRITE_REG(TAMP->SCR, IntTamper); + + return HAL_OK; +} +#endif /* TAMP */ + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group2 + * @brief RTC Wake-up functions + * +@verbatim + =============================================================================== + ##### RTC Wake-up functions ##### + =============================================================================== + + [..] This section provides functions allowing to configure Wake-up feature + +@endverbatim + * @{ + */ + +/** + * @brief Set wake up timer. + * @param hrtc RTC handle + * @param WakeUpCounter Wake up counter + * @param WakeUpClock Wake up clock + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock) +{ + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock)); + assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Clear WUTE in RTC_CR to disable the wakeup timer */ + CLEAR_BIT(RTC->CR, RTC_CR_WUTE); + + /* Poll WUTWF until it is set in RTC_ICSR / RTC_ISR to make sure the access to wakeup autoreload + counter and to WUCKSEL[2:0] bits is allowed. This step must be skipped in + calendar initialization mode. */ +#if defined(TAMP) + if (READ_BIT(RTC->ICSR, RTC_ICSR_INITF) == 0U) + { + tickstart = HAL_GetTick(); + + while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) == 0U) +#else + if (READ_BIT(RTC->ISR, RTC_ISR_INITF) == 0U) + { + tickstart = HAL_GetTick(); + + while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U) +#endif /* TAMP */ + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + } + + /* Clear the Wakeup Timer clock source bits and configure the clock source in CR register */ + uint32_t CR_tmp = hrtc->Instance->CR; + CR_tmp &= (uint32_t)~RTC_CR_WUCKSEL; + CR_tmp |= (uint32_t)WakeUpClock; + hrtc->Instance->CR = CR_tmp; + + /* Configure the Wakeup Timer counter */ + hrtc->Instance->WUTR = (uint32_t)WakeUpCounter; + + /* Enable the Wakeup Timer */ + __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Set wake up timer with interrupt. + * @param hrtc RTC handle + * @param WakeUpCounter Wake up counter + * @param WakeUpClock Wake up clock + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock) +{ + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock)); + assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Clear WUTE in RTC_CR to disable the wakeup timer */ + CLEAR_BIT(RTC->CR, RTC_CR_WUTE); + + /* Poll WUTWF until it is set in RTC_ICSR to make sure the access to wakeup autoreload + counter and to WUCKSEL[2:0] bits is allowed. This step must be skipped in + calendar initialization mode. */ +#if defined(TAMP) + if (READ_BIT(RTC->ICSR, RTC_ICSR_INITF) == 0U) + { + tickstart = HAL_GetTick(); + + while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) == 0U) +#else + if (READ_BIT(RTC->ISR, RTC_ISR_INITF) == 0U) + { + tickstart = HAL_GetTick(); + + while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U) +#endif /* TAMP */ + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + } + + /* Configure the Wakeup Timer counter */ + hrtc->Instance->WUTR = (uint32_t)WakeUpCounter; + + /* Clear the Wakeup Timer clock source bits and configure the clock source in CR register */ + { + uint32_t CR_tmp = hrtc->Instance->CR; + CR_tmp &= (uint32_t)~RTC_CR_WUCKSEL; + CR_tmp |= (uint32_t)WakeUpClock; + hrtc->Instance->CR = CR_tmp; + } + + /* RTC WakeUpTimer Interrupt Configuration: EXTI configuration */ +#if defined(DUAL_CORE) + if (HAL_GetCurrentCPUID() == CM7_CPUID) + { + __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT(); + } + else + { + __HAL_RTC_WAKEUPTIMER_EXTID2_ENABLE_IT(); + } +#else /* SINGLE_CORE */ + __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT(); +#endif /* DUAL_CORE */ + + __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_RISING_EDGE(); + + /* Configure the Interrupt in the RTC_CR register */ + __HAL_RTC_WAKEUPTIMER_ENABLE_IT(hrtc, RTC_IT_WUT); + + /* Enable the Wakeup Timer */ + __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Deactivate wake up timer counter. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc) +{ + uint32_t tickstart; + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Disable the Wakeup Timer */ + __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc); + + /* In case of interrupt mode is used, the interrupt source must disabled */ + __HAL_RTC_WAKEUPTIMER_DISABLE_IT(hrtc, RTC_IT_WUT); + + tickstart = HAL_GetTick(); + /* Wait till RTC WUTWF flag is set and if timeout is reached exit */ +#if defined(TAMP) + while (READ_BIT(hrtc->Instance->ICSR, RTC_FLAG_WUTWF) == 0U) +#else + while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == 0U) +#endif /* TAMP */ + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Get wake up timer counter. + * @param hrtc RTC handle + * @retval Counter value + */ +uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc) +{ + /* Get the counter value */ + return ((uint32_t)(hrtc->Instance->WUTR & RTC_WUTR_WUT)); +} + +/** + * @brief Handle Wake Up Timer interrupt request. + * @param hrtc RTC handle + * @retval None + */ +void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc) +{ + /* Clear the EXTI's line Flag for RTC WakeUpTimer */ +#if defined(DUAL_CORE) + if (HAL_GetCurrentCPUID() == CM7_CPUID) + { + __HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG(); + } + else + { + __HAL_RTC_WAKEUPTIMER_EXTID2_CLEAR_FLAG(); + } +#else /* SINGLE_CORE */ + __HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG(); +#endif /* DUAL_CORE */ + +#if defined(TAMP) + /* Get the pending status of the WAKEUPTIMER Interrupt */ + if ((hrtc->Instance->MISR & RTC_MISR_WUTMF) != 0u) + { + /* Immediately clear flags */ + hrtc->Instance->SCR = RTC_SCR_CWUTF; + + /* WAKEUPTIMER callback */ + #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call WakeUpTimerEvent registered Callback */ + hrtc->WakeUpTimerEventCallback(hrtc); + #else + HAL_RTCEx_WakeUpTimerEventCallback(hrtc); + #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } +#else + /* Get the pending status of the WAKEUPTIMER Interrupt */ + if (__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) != 0U) + { + /* Clear the WAKEUPTIMER interrupt pending bit */ + __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); + + /* WAKEUPTIMER callback */ + #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1) + /* Call WakeUpTimerEvent registered Callback */ + hrtc->WakeUpTimerEventCallback(hrtc); + #else + HAL_RTCEx_WakeUpTimerEventCallback(hrtc); + #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */ + } +#endif /* TAMP */ + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; +} + +/** + * @brief Wake Up Timer callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef * hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_WakeUpTimerEventCallback could be implemented in the user file + */ +} + + +/** + * @brief Handle Wake Up Timer Polling. + * @param hrtc RTC handle + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef * hrtc, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) == 0U) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Clear the WAKEUPTIMER Flag */ + __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +/** + * @} + */ + + +/** @addtogroup RTCEx_Exported_Functions_Group6 + * @brief Extended RTC Backup register functions + * +@verbatim + =============================================================================== + ##### Extended RTC Backup register functions ##### + =============================================================================== + [..] + (+) Before calling any tamper or internal tamper function, you have to call first + HAL_RTC_Init() function. + (+) In that ine you can select to output tamper event on RTC pin. + [..] + This subsection provides functions allowing to + (+) Write a data in a specified RTC Backup data register + (+) Read a data in a specified RTC Backup data register +@endverbatim + * @{ + */ + + +/** + * @brief Write a data in a specified RTC Backup data register. + * @param hrtc RTC handle + * @param BackupRegister RTC Backup data Register number. + * This parameter can be: RTC_BKP_DRx where x can be from 0 to 31 to + * specify the register. + * @param Data Data to be written in the specified Backup data register. + * @retval None + */ +void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef * hrtc, uint32_t BackupRegister, uint32_t Data) +{ + uint32_t tmp; + + /* Check the parameters */ + assert_param(IS_RTC_BKP(BackupRegister)); + + /* Point on address of first backup register */ +#if defined(TAMP) + tmp = (uint32_t) & (((TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET))->BKP0R); +#else + tmp = (uint32_t) & (hrtc->Instance->BKP0R); +#endif /* TAMP */ + + tmp += (BackupRegister * 4U); + + /* Write the specified register */ + *(__IO uint32_t *)tmp = (uint32_t)Data; +} + + +/** + * @brief Read data from the specified RTC Backup data Register. + * @param hrtc RTC handle + * @param BackupRegister RTC Backup data Register number. + * This parameter can be: RTC_BKP_DRx where x can be from 0 to 31 to + * specify the register. + * @retval Read value + */ +uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef * hrtc, uint32_t BackupRegister) +{ + uint32_t tmp; + + /* Check the parameters */ + assert_param(IS_RTC_BKP(BackupRegister)); + + /* Point on address of first backup register */ +#if defined(TAMP) + tmp = (uint32_t) & (((TAMP_TypeDef *)((uint32_t)hrtc->Instance + TAMP_OFFSET))->BKP0R); +#else + tmp = (uint32_t) & (hrtc->Instance->BKP0R); +#endif /* TAMP */ + + tmp += (BackupRegister * 4U); + + /* Read the specified register */ + return (*(__IO uint32_t *)tmp); +} + + +/** + * @} + */ + + +/** @addtogroup RTCEx_Exported_Functions_Group3 + * @brief Extended Peripheral Control functions + * +@verbatim + =============================================================================== + ##### Extended Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides functions allowing to + (+) Write a data in a specified RTC Backup data register + (+) Read a data in a specified RTC Backup data register + (+) Set the Smooth calibration parameters. + (+) Set Low Power calibration parameter (if feature supported). + (+) Configure the Synchronization Shift Control Settings. + (+) Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). + (+) Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). + (+) Enable the RTC reference clock detection. + (+) Disable the RTC reference clock detection. + (+) Enable the Bypass Shadow feature. + (+) Disable the Bypass Shadow feature. + +@endverbatim + * @{ + */ + + +/** + * @brief Set the Smooth calibration parameters. + * @param hrtc RTC handle + * @param SmoothCalibPeriod Select the Smooth Calibration Period. + * This parameter can be can be one of the following values : + * @arg RTC_SMOOTHCALIB_PERIOD_32SEC: The smooth calibration period is 32s. + * @arg RTC_SMOOTHCALIB_PERIOD_16SEC: The smooth calibration period is 16s. + * @arg RTC_SMOOTHCALIB_PERIOD_8SEC: The smooth calibration period is 8s. + * @param SmoothCalibPlusPulses Select to Set or reset the CALP bit. + * This parameter can be one of the following values: + * @arg RTC_SMOOTHCALIB_PLUSPULSES_SET: Add one RTCCLK pulse every 2*11 pulses. + * @arg RTC_SMOOTHCALIB_PLUSPULSES_RESET: No RTCCLK pulses are added. + * @param SmoothCalibMinusPulsesValue Select the value of CALM[8:0] bits. + * This parameter can be one any value from 0 to 0x000001FF. + * @note To deactivate the smooth calibration, the field SmoothCalibPlusPulses + * must be equal to SMOOTHCALIB_PLUSPULSES_RESET and the field + * SmoothCalibMinusPulsesValue must be equal to 0. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef * hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue) +{ + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_RTC_SMOOTH_CALIB_PERIOD(SmoothCalibPeriod)); + assert_param(IS_RTC_SMOOTH_CALIB_PLUS(SmoothCalibPlusPulses)); + assert_param(IS_RTC_SMOOTH_CALIB_MINUS(SmoothCalibMinusPulsesValue)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + +#if defined(TAMP) + /* check if a calibration operation is pending */ + if ((hrtc->Instance->ICSR & RTC_ICSR_RECALPF) != 0U) + { + tickstart = HAL_GetTick(); + + /* Wait for pending calibration operation to finish */ + while ((hrtc->Instance->ICSR & RTC_ICSR_RECALPF) != 0U) +#else + /* check if a calibration operation is pending */ + if ((hrtc->Instance->ISR & RTC_ISR_RECALPF) != 0U) + { + tickstart = HAL_GetTick(); + + /* Wait for pending calibration operation to finish */ + while ((hrtc->Instance->ISR & RTC_ISR_RECALPF) != 0U) +#endif /* TAMP */ + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + } + + /* Configure the Smooth calibration settings */ + MODIFY_REG(hrtc->Instance->CALR, (RTC_CALR_CALP | RTC_CALR_CALW8 | RTC_CALR_CALW16 | RTC_CALR_CALM), (uint32_t)(SmoothCalibPeriod | SmoothCalibPlusPulses | SmoothCalibMinusPulsesValue)); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Configure the Synchronization Shift Control Settings. + * @note When REFCKON is set, firmware must not write to Shift control register. + * @param hrtc RTC handle + * @param ShiftAdd1S Select to add or not 1 second to the time calendar. + * This parameter can be one of the following values: + * @arg RTC_SHIFTADD1S_SET: Add one second to the clock calendar. + * @arg RTC_SHIFTADD1S_RESET: No effect. + * @param ShiftSubFS Select the number of Second Fractions to substitute. + * This parameter can be one any value from 0 to 0x7FFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef * hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS) +{ + uint32_t tickstart; + + /* Check the parameters */ + assert_param(IS_RTC_SHIFT_ADD1S(ShiftAdd1S)); + assert_param(IS_RTC_SHIFT_SUBFS(ShiftSubFS)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + tickstart = HAL_GetTick(); + + /* Wait until the shift is completed */ +#if defined(TAMP) + while ((hrtc->Instance->ICSR & RTC_ICSR_SHPF) != 0U) +#else + while ((hrtc->Instance->ISR & RTC_ISR_SHPF) != 0U) +#endif /* TAMP */ + { + if ((HAL_GetTick() - tickstart) > RTC_TIMEOUT_VALUE) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_TIMEOUT; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_TIMEOUT; + } + } + + /* Check if the reference clock detection is disabled */ + if ((hrtc->Instance->CR & RTC_CR_REFCKON) == 0U) + { + /* Configure the Shift settings */ + hrtc->Instance->SHIFTR = (uint32_t)(uint32_t)(ShiftSubFS) | (uint32_t)(ShiftAdd1S); + + /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ + if ((hrtc->Instance->CR & RTC_CR_BYPSHAD) == 0U) + { + if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + hrtc->State = HAL_RTC_STATE_ERROR; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_ERROR; + } + } + } + else + { + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_ERROR; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_ERROR; + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Configure the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). + * @param hrtc RTC handle + * @param CalibOutput Select the Calibration output Selection. + * This parameter can be one of the following values: + * @arg RTC_CALIBOUTPUT_512HZ: A signal has a regular waveform at 512Hz. + * @arg RTC_CALIBOUTPUT_1HZ: A signal has a regular waveform at 1Hz. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef * hrtc, uint32_t CalibOutput) +{ + /* Check the parameters */ + assert_param(IS_RTC_CALIB_OUTPUT(CalibOutput)); + + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Clear flags before config */ + hrtc->Instance->CR &= (uint32_t)~RTC_CR_COSEL; + + /* Configure the RTC_CR register */ + hrtc->Instance->CR |= (uint32_t)CalibOutput; + + __HAL_RTC_CALIBRATION_OUTPUT_ENABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Deactivate the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef * hrtc) +{ + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + __HAL_RTC_CALIBRATION_OUTPUT_DISABLE(hrtc); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Enable the RTC reference clock detection. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef * hrtc) +{ + HAL_StatusTypeDef status; + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Enter Initialization mode */ + status = RTC_EnterInitMode(hrtc); + if (status == HAL_OK) + { + __HAL_RTC_CLOCKREF_DETECTION_ENABLE(hrtc); + + /* Exit Initialization mode */ + status = RTC_ExitInitMode(hrtc); + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + if (status == HAL_OK) + { + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + } + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Disable the RTC reference clock detection. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef * hrtc) +{ + HAL_StatusTypeDef status; + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Enter Initialization mode */ + status = RTC_EnterInitMode(hrtc); + if (status == HAL_OK) + { + __HAL_RTC_CLOCKREF_DETECTION_DISABLE(hrtc); + + /* Exit Initialization mode */ + status = RTC_ExitInitMode(hrtc); + } + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + if (status == HAL_OK) + { + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + } + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Enable the Bypass Shadow feature. + * @note When the Bypass Shadow is enabled the calendar value are taken + * directly from the Calendar counter. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef * hrtc) +{ + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Set the BYPSHAD bit */ + hrtc->Instance->CR |= (uint8_t)RTC_CR_BYPSHAD; + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +/** + * @brief Disable the Bypass Shadow feature. + * @note When the Bypass Shadow is enabled the calendar value are taken + * directly from the Calendar counter. + * @param hrtc RTC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef * hrtc) +{ + /* Process Locked */ + __HAL_LOCK(hrtc); + + hrtc->State = HAL_RTC_STATE_BUSY; + + /* Disable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); + + /* Reset the BYPSHAD bit */ + hrtc->Instance->CR &= ((uint8_t)~RTC_CR_BYPSHAD); + + /* Enable the write protection for RTC registers */ + __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hrtc); + + return HAL_OK; +} + +#if defined(TAMP) +/** + * @brief Increment Monotonic counter. + * @param hrtc RTC handle + * @param Instance Monotonic counter Instance + * This parameter can be can be one of the following values : + * @arg RTC_MONOTONIC_COUNTER_1 + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterIncrement(RTC_HandleTypeDef *hrtc, uint32_t Instance) +{ + UNUSED(hrtc); + UNUSED(Instance); + /* This register is read-only only and is incremented by one when a write access is done to this + register. This register cannot roll-over and is frozen when reaching the maximum value. */ + CLEAR_REG(TAMP->COUNTR); + + return HAL_OK; +} + +/** + * @brief Monotonic counter incrementation. + * @param hrtc RTC handle + * @param Instance Monotonic counter Instance + * This parameter can be can be one of the following values : + * @arg RTC_MONOTONIC_COUNTER_1 + * @param Counter monotonic counter value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_MonotonicCounterGet(RTC_HandleTypeDef *hrtc, uint32_t *Counter, uint32_t Instance) +{ + UNUSED(hrtc); + UNUSED(Instance); + /* This register is read-only only and is incremented by one when a write access is done to this + register. This register cannot roll-over and is frozen when reaching the maximum value. */ + *Counter = READ_REG(TAMP->COUNTR); + + return HAL_OK; +} +#endif /* TAMP */ + +/** + * @} + */ + +/** @addtogroup RTCEx_Exported_Functions_Group4 + * @brief Extended features functions + * +@verbatim + =============================================================================== + ##### Extended features functions ##### + =============================================================================== + [..] This section provides functions allowing to: + (+) RTC Alarm B callback + (+) RTC Poll for Alarm B request + +@endverbatim + * @{ + */ + +/** + * @brief Alarm B callback. + * @param hrtc RTC handle + * @retval None + */ +__weak void HAL_RTCEx_AlarmBEventCallback(RTC_HandleTypeDef * hrtc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hrtc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_RTCEx_AlarmBEventCallback could be implemented in the user file + */ +} + +/** + * @brief Handle Alarm B Polling request. + * @param hrtc RTC handle + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RTCEx_PollForAlarmBEvent(RTC_HandleTypeDef * hrtc, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + while (__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBF) == 0U) + { + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + hrtc->State = HAL_RTC_STATE_TIMEOUT; + return HAL_TIMEOUT; + } + } + } + + /* Clear the Alarm Flag */ + __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF); + + /* Change RTC state */ + hrtc->State = HAL_RTC_STATE_READY; + + return HAL_OK; +} + +/** + * @} + */ + + +/** + * @} + */ + +#endif /* HAL_RTC_MODULE_ENABLED */ + +/** + * @} + */ + +/** + * @} + */ + |