1 files changed, 123 insertions, 0 deletions
diff --git a/bsps/arm/smdk2410/clock/clockdrv.c b/bsps/arm/smdk2410/clock/clockdrv.c
new file mode 100644
index 0000000000..0430826254
--- /dev/null
+++ b/bsps/arm/smdk2410/clock/clockdrv.c
@@ -0,0 +1,123 @@
+/*
+ *  S3C2400 clock specific using the System Timer
+ */
+
+/*
+ *  The license and distribution terms for this file may be
+ *  found in the file LICENSE in this distribution or at
+ *  http://www.rtems.org/license/LICENSE.
+ */
+
+#include <rtems.h>
+#include <bsp/irq.h>
+#include <bsp.h>
+#include <s3c24xx.h>
+
+void Clock_isr(rtems_irq_hdl_param arg);
+static void clock_isr_on(const rtems_irq_connect_data *unused);
+static void clock_isr_off(const rtems_irq_connect_data *unused);
+static int clock_isr_is_on(const rtems_irq_connect_data *irq);
+
+rtems_irq_connect_data clock_isr_data = {
+  .name   = BSP_INT_TIMER4,
+  .hdl    = Clock_isr,
+  .handle = NULL,
+  .on     = clock_isr_on,
+  .off    = clock_isr_off,
+  .isOn   = clock_isr_is_on,
+};
+
+/**
+ * When we get the clock interrupt
+ *    - clear the interrupt bit?
+ *    - restart the timer?
+ */
+#define Clock_driver_support_at_tick()                \
+  do {                                                \
+        ClearPending(BIT_TIMER4);                     \
+  } while(0)
+
+
+/**
+ * Installs the clock ISR. You shouldn't need to change this.
+ */
+#define Clock_driver_support_install_isr( _new ) \
+  BSP_install_rtems_irq_handler(&clock_isr_data)
+
+
+/**
+ * Initialize the hardware for the clock
+ *   - Set the frequency
+ *   - enable it
+ *   - clear any pending interrupts
+ *
+ * Since you may want the clock always running, you can
+ * enable interrupts here. If you do so, the clock_isr_on(),
+ * clock_isr_off(), and clock_isr_is_on() functions can be
+ * NOPs.
+ */
+#define Clock_driver_support_initialize_hardware() \
+  do { \
+        uint32_t cr; \
+        uint32_t freq; \
+        /* set MUX for Timer4 to 1/16 */ \
+        cr=rTCFG1 & 0xFFF0FFFF; \
+        rTCFG1=(cr | (3<<16)); \
+        freq = get_PCLK(); \
+        /* set TIMER4 counter, input freq=PLCK/16/16Mhz*/ \
+        freq = (freq /16)/16; \
+        rTCNTB4 = ((freq / 1000) * rtems_configuration_get_microseconds_per_tick()) / 1000; \
+        /*unmask TIMER4 irq*/ \
+        rINTMSK&=~BIT_TIMER4; \
+        /* start TIMER4 with autoreload */ \
+        cr=rTCON & 0xFF8FFFFF; \
+        rTCON=(cr|(0x6<<20)); \
+        rTCON=(cr|(0x5<<20)); \
+    } while (0)
+
+/**
+ * Do whatever you need to shut the clock down and remove the
+ * interrupt handler. Since this normally only gets called on
+ * RTEMS shutdown, you may not need to do anything other than
+ * remove the ISR.
+ */
+#define Clock_driver_support_shutdown_hardware()                        \
+  do {                                                                  \
+        /* Disable timer */ \
+        BSP_remove_rtems_irq_handler(&clock_isr_data);                  \
+     } while (0)
+
+/**
+ * Enables clock interrupt.
+ *
+ * If the interrupt is always on, this can be a NOP.
+ */
+static void clock_isr_on(const rtems_irq_connect_data *unused)
+{
+}
+
+/**
+ * Disables clock interrupts
+ *
+ * If the interrupt is always on, this can be a NOP.
+ */
+static void clock_isr_off(const rtems_irq_connect_data *unused)
+{
+    return;
+}
+
+/**
+ * Tests to see if clock interrupt is enabled, and returns 1 if so.
+ * If interrupt is not enabled, returns 0.
+ *
+ * If the interrupt is always on, this always returns 1.
+ */
+static int clock_isr_is_on(const rtems_irq_connect_data *irq)
+{
+  return 1;
+}
+
+#define CLOCK_DRIVER_USE_DUMMY_TIMECOUNTER
+
+/* Make sure to include this, and only at the end of the file */
+#include "../../../shared/dev/clock/clockimpl.h"