This is a large patch from Eric Valette <valette@crf.canon.fr> that was

described in the message following this paragraph.  This patch also includes
a mcp750 BSP.

From valette@crf.canon.fr Mon Jun 14 10:03:08 1999
Date: Tue, 18 May 1999 01:30:14 +0200 (CEST)
From: VALETTE Eric <valette@crf.canon.fr>
To: joel@oarcorp.com
Cc: raguet@crf.canon.fr, rtems-snapshots@oarcorp.com, valette@crf.canon.fr
Subject: Questions/Suggestion regarding RTEMS PowerPC code (long)


Dear knowledgeable RTEMS powerpc users,

As some of you may know, I'm currently finalizing a port
of RTEMS on a MCP750 Motorola board. I have done most
of it but have some questions to ask before submitting
the port.

In order to understand some of the changes I have made
or would like to make, maybe it is worth describing the
MCP750 Motorola board.

the MCP750 is a COMPACT PCI powerpc board with :

	1) a MPC750 233 MHz processor,
	2) a raven bus bridge/PCI controller that
	implement an OPENPIC compliant interrupt controller,
	3) a VIA 82C586 PCI/ISA bridge that offers a PC
	compliant IO for keyboard, serial line, IDE, and
	the well known PC 8259 cascaded PIC interrupt
	architecture model,
	4) a DEC 21140 Ethernet controller,
	5) the PPCBUG Motorola firmware in flash,
	6) A DEC PCI bridge,

This architecture is common to most Motorola 60x/7xx
board except that :
	1) on VME board, the DEC PCI bridge is replaced by
	a VME chipset,
	2) the VIA 82C586 PCI/ISA bridge is replaced by
	another bridge that is almost fully compatible
	with the via bridge...

So the port should be a rather close basis for many
60x/7xx motorola board...

On this board, I already have ported Linux 2.2.3 and
use it both as a development and target board.

Now the questions/suggestions I have :

1)  EXCEPTION CODE
-------------------

As far as I know exceptions on PPC are handled like
interrupts. I dislike this very much as :

	a) Except for the decrementer exception (and
	maybe some other on mpc8xx), exceptions are
	not recoverable and the handler just need to print
	the full context and go to the firmware or debugger...
	b) The interrupt switch is only necessary for the
	decrementer and external interrupt (at least on
	6xx,7xx).
	c) The full context for exception is never saved and
	thus cannot be used by debugger... I do understand
	the most important for interrupts low level code
	is to save the minimal context enabling	to call C
	code for performance reasons. On non recoverable
	exception on the other hand, the most important is
	to save the maximum information concerning proc status
	in order to analyze the reason of the fault. At
	least we will need this in order to implement the
	port of RGDB on PPC

==> I wrote an API for connecting raw exceptions (and thus
raw interrupts) for mpc750. It should be valid for most
powerpc processors... I hope to find a way to make this coexist
with actual code layout. The code is actually located
in lib/libcpu/powerpc/mpc750 and is thus optional
(provided I write my own version of exec/score/cpu/powerpc/cpu.c ...)

See remark about files/directory layout organization in 4)

2) Current Implementation of ISR low level code
-----------------------------------------------

I do not understand why the MSR EE flags is cleared
again in exec/score/cpu/powerpc/irq_stubs.S

#if (PPC_USE_SPRG)
	mfmsr	r5
	mfspr   r6, sprg2
#else
        lwz	r6,msr_initial(r11)
	lis     r5,~PPC_MSR_DISABLE_MASK@ha
        ori     r5,r5,~PPC_MSR_DISABLE_MASK@l
	and	r6,r6,r5
	mfmsr	r5
#endif

Reading the doc, when a decrementer interrupt or an
external interrupt is active, the MSR EE flag is already
cleared. BTW if exception/interrupt could occur, it would
trash SRR0 and SRR1. In fact the code may be useful to set
MSR[RI] that re-enables exception processing. BTW I will need
to set other value in MSR to handle interrupts :

	a) I want the MSR[IR] and MSR[DR] to be set for
	performance reasons and also because I need DBAT
	support to have access to PCI memory space as the
	interrupt controller is in the PCI space.

Reading the code, I see others have the same kind of request :

/* SCE 980217
 *
 * We need address translation ON when we call our ISR routine

	mtmsr	r5

 */

This is just another prof that even the lowest level
IRQ code is fundamentally board dependent and
not simply processor dependent especially when
the processor use external interrupt controller
because it has a single interrupt request line...

Note that if you look at the PPC code high level interrupt
handling code, as the "set_vector" routine that really connects
the interrupt is in the BSP/startup/genpvec.c,
the fact that IRQ handling is BSP specific is DE-FACTO
acknowledged.

I know I have already expressed this and understand that this
would require some heavy change in the code but believe
me you will reach a point where you will not be able
to find a compatible while optimum implementation for low level
interrupt handling code...) In my case this is already true...

So please consider removing low level IRQ handling from
exec/score/cpu/* and only let there exception handling code...
Exceptions are usually only processor dependent and do
not depend on external hardware mechanism to be masked or
acknowledged or re-enabled (there are probably exception but ...)

I have already done this for pc386 bsp but need to make it again.
This time I will even propose an API.

3) R2/R13 manipulation for EABI implementation
----------------------------------------------

I do not understand the handling of r2 and r13 in the
EABI case. The specification for r2 says pointer to sdata2,
sbss2 section => constant. However I do not see -ffixed-r2
passed to any compilation system in make/custom/*
(for info linux does this on PPC).

So either this is a default compiler option when choosing
powerpc-rtems and thus we do not need to do anything with
this register as all the code is compiled with this compiler
and linked together OR this register may be used by rtems code
and then we do not need any special initialization or
handling.

The specification for r13 says pointer to the small data
area. r13 argumentation is the same except that as far
as I know the usage of the small data area requires
specific compiler support so that access to variables is
compiled via loading the LSB in a register and then
using r13 to get full address... It is like a small
memory model and it was present in IBM C compilers.

=> I propose to suppress any specific code for r2 and
r13 in the EABI case.

4) Code layout organization (yes again :-))
-------------------------------------------

I think there are a number of design flaws in the way
the code is for ppc organized and I will try to point them out.
I have been beaten by this again on this new port, and
was beaten last year while modifying code for pc386.

a) exec/score/cpu/* vs lib/libcpu/cpu/*.

I think that too many things are put in exec/score/cpu that
have nothing to do with RTEMS internals but are rather
related to CPU feature.

This include at least :

	a) registers access routine (e.g GET_MSR_Value),
	b) interrupt masking/unmasking routines,
	c) cache_mngt_routine,
	d) mmu_mngt_routine,
	e) Routines to connect the raw_exception, raw_interrupt
	handler,

b) lib/libcpu/cpu/powerpc/*

With a processor family as exuberant as the powerpc family,
and their well known subtle differences (604 vs 750) or
unfortunately majors (8xx vs 60x)  the directory structure
is fine (except maybe the names that are not homogeneous)

	powerpc

ppc421 mpc821 ...

I only needed to add mpc750. But the fact that libcpu.a was not
produced was a pain and the fact that this organization may
duplicates code is also problematic.

So, except if the support of automake provides a better solution
I would like to propose something like this :

		powerpc

mpc421 	mpc821	...	mpc750	shared wrapup

with the following rules :

	a) "shared" would act as a source container for sources that may
	be shared among processors. Needed files would be compiled inside
	the processor specific directory using the vpath Makefile
	mechanism. "shared" may also contain compilation code
	for routine that are really shared and not worth to inline...
	(did not found many things so far as registers access routine
	ARE WORTH INLINING)... In the case something is compiled there,
	it should create libcpushared.a

	b) layout under processor specific directory is free provided
	that
		1)the result of the compilation process exports :

		libcpu/powerpc/"PROC"/*.h in $(PROJECT_INCLUDE)/libcpu

		2) each processor specific directory creates
		a library called libcpuspecific.a
	Note that this organization enables to have a file that
	is nearly the same than in shared but that must differ
	because of processor differences...

	c) "wrapup" should create libcpu.a using libcpushared.a
	libcpuspecific.a and export it $(PROJECT_INCLUDE)/libcpu

The only thing I have no ideal solution is the way to put shared
definitions in "shared" and only processor specific definition
in "proc". To give a concrete example, most MSR bit definition
are shared among PPC processors and only some differs. if we create
a single msr.h in shared it will have ifdef. If in msr.h we
include libcpu/msr_c.h we will need to have it in each prowerpc
specific directory (even empty). Opinions are welcomed ...

Note that a similar mechanism exist in libbsp/i386 that also
contains a shared directory that is used by several bsp
like pc386 and i386ex and a similar wrapup mechanism...

NB: I have done this for mpc750 and other processors could just use
similar Makefiles...

c) The exec/score/cpu/powerpc directory layout.

I think the directory layout should be the same than the
libcpu/powerpc. As it is not, there are a lot of ifdefs
inside the code... And of course low level interrupt handling
code should be removed...

Besides that I do not understand why

	1) things are compiled in the wrap directory,
	2) some includes are moved to rtems/score,

I think the "preinstall" mechanism enables to put
everything in the current directory (or better in a per processor
directory),


5) Interrupt handling API
-------------------------

Again :-). But I think that using all the features the PIC
offers is a MUST for RT system. I already explained in the
prologue of this (long and probably boring) mail that the MCP750
boards offers an OPENPIC compliant architecture and that
the VIA 82586 PCI/ISA bridge offers a PC compatible IO and
PIC mapping. Here is a logical view of the RAVEN/VIA 82586
interrupt mapping :


---------    0  ------
| OPEN	| <-----|8259|
| PIC	|	|    |    2  ------
|(RAVEN)|	|    | <-----|8259|
|	|	|    |	     |    |   11
|	|	|    |	     |    | <----
|	|	|    |	     |    |
|	|	|    |	     |    |
---------       ------	     |    |
    ^			     ------
    |		VIA PCI/ISA bridge
    |  x
    -------- PCI interrupts

OPENPIC offers interrupt priorities among PCI interrupts
and interrupt selective masking. The 8259 offers the same kind
of feature. With actual powerpc interrupt code :

	1) there is no way to specify priorities among
	interrupts handler. This is REALLY a bad thing.
	For me it is as importnat as having priorities
	for threads...
	2) for my implementation, each ISR should
	contain the code that acknowledge the RAVEN
	and 8259 cascade, modify interrupt mask on both
	chips, and reenable interrupt at processor level,
	..., restore then on interrupt return,.... This code
	is actually similar to code located in some
	genpvec.c powerpc files,
	3) I must update _ISR_Nesting_level because
	irq.inl use it...
	4) the libchip code connects the ISR via set_vector
	but the libchip handler code does not contain any code to
	manipulate external interrupt controller hardware
	in order to acknoledge the interrupt or re-enable
	them (except for the target hardware of course)
	So this code is broken unless set_vector adds an
	additionnal prologue/epilogue before calling/returning
	from in order to acknoledge/mask the raven and the
	8259 PICS... => Anyway already EACH BSP MUST REWRITE
	PART OF INTERRUPT HANDLING CODE TO CORRECTLY IMPLEMENT
	SET_VECTOR.

I would rather offer an API similar to the one provided
in libbsp/i386/shared/irq/irq.h so that :

	1) Once the driver supplied methods is called the
	only things the ISR has to do is to worry about the
	external hardware that triggered the interrupt.
	Everything on openpic/VIA/processor would have been
	done by the low levels (same things as set-vector)
	2) The caller will need to supply the on/off/isOn
	routine that are fundamental to correctly implements
	debuggers/performance monitoring is a portable way
	3) A globally configurable interrupt priorities
	mechanism...

I have nothing against providing a compatible
set_vector just to make libchip happy but
as I have already explained in  other
mails (months ago), I really think that the ISR
connection should be handled by the BSP and that no
code containing irq connection should exist the
rtems generic layers... Thus I really dislike
libchip on this aspect because in a long term
it will force to adopt the less reach API
for interrupt handling that exists (set_vector).

Additional note : I think the _ISR_Is_in_progress()
inline routine should be :

	1) Put in a processor specific section,
	2) Should not rely on a global variable,

As :
	a) on symmetric MP, there is one interrupt level
	per CPU,
	b) On processor that have an ISP (e,g 68040),
	this variable is useless (MSR bit testing could
	be used)
	c) On PPC, instead of using the address of the
	variable via __CPU_IRQ_info.Nest_level a dedicated
	SPR could be used.

NOTE:	most of this is also true for _Thread_Dispatch_disable_level


END NOTE
--------

Please do not take what I said in the mail as a criticism for
anyone who submitted ppc code. Any code present helped me
a lot understanding PPC behavior. I just wanted by this
mail to :
	1) try to better understand the actual code,
	2) propose concrete ways of enhancing current code
	by providing an alternative implementation for MCP750. I
	will make my best effort to try to brake nothing but this
	is actually hard due to the file layout organisation.
	3) make understandable some changes I will probably make
	if joel let me do them :-)

Any comments/objections are welcomed as usual.



--
   __
  /  `                   	Eric Valette
 /--   __  o _.          	Canon CRF
(___, / (_(_(__         	Rue de la touche lambert
				35517 Cesson-Sevigne  Cedex
				FRANCE
Tel: +33 (0)2 99 87 68 91	Fax: +33 (0)2 99 84 11 30
E-mail: valette@crf.canon.fr

1 files changed, 2143 insertions, 0 deletions

diff --git a/c/src/lib/libbsp/powerpc/mcp750/bootloader/zlib.c b/c/src/lib/libbsp/powerpc/mcp750/bootloader/zlib.c
new file mode 100644
index 0000000000..78ba7867fc
--- /dev/null
+++ b/c/src/lib/libbsp/powerpc/mcp750/bootloader/zlib.c
@@ -0,0 +1,2143 @@
+/*
+ * This file is derived from various .h and .c files from the zlib-0.95
+ * distribution by Jean-loup Gailly and Mark Adler, with some additions
+ * by Paul Mackerras to aid in implementing Deflate compression and
+ * decompression for PPP packets.  See zlib.h for conditions of
+ * distribution and use.
+ *
+ * Changes that have been made include:
+ * - changed functions not used outside this file to "local"
+ * - added minCompression parameter to deflateInit2
+ * - added Z_PACKET_FLUSH (see zlib.h for details)
+ * - added inflateIncomp
+ *
+ * $Id$
+ */
+
+/*+++++*/
+/* zutil.h -- internal interface and configuration of the compression library
+ * Copyright (C) 1995 Jean-loup Gailly.
+ * For conditions of distribution and use, see copyright notice in zlib.h
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+/* From: zutil.h,v 1.9 1995/05/03 17:27:12 jloup Exp */
+
+#define _Z_UTIL_H
+
+#include "zlib.h"
+
+#ifndef local
+#  define local static
+#endif
+/* compile with -Dlocal if your debugger can't find static symbols */
+
+#define FAR
+
+typedef unsigned char  uch;
+typedef uch FAR uchf;
+typedef unsigned short ush;
+typedef ush FAR ushf;
+typedef unsigned long  ulg;
+
+extern char *z_errmsg[]; /* indexed by 1-zlib_error */
+
+#define ERR_RETURN(strm,err) return (strm->msg=z_errmsg[1-err], err)
+/* To be used only when the state is known to be valid */
+
+#ifndef NULL
+#define NULL	((void *) 0)
+#endif
+
+        /* common constants */
+
+#define DEFLATED   8
+
+#ifndef DEF_WBITS
+#  define DEF_WBITS MAX_WBITS
+#endif
+/* default windowBits for decompression. MAX_WBITS is for compression only */
+
+#if MAX_MEM_LEVEL >= 8
+#  define DEF_MEM_LEVEL 8
+#else
+#  define DEF_MEM_LEVEL  MAX_MEM_LEVEL
+#endif
+/* default memLevel */
+
+#define STORED_BLOCK 0
+#define STATIC_TREES 1
+#define DYN_TREES    2
+/* The three kinds of block type */
+
+#define MIN_MATCH  3
+#define MAX_MATCH  258
+/* The minimum and maximum match lengths */
+
+         /* functions */
+
+#include <string.h>
+#define zmemcpy memcpy
+#define zmemzero(dest, len)	memset(dest, 0, len)
+
+/* Diagnostic functions */
+#ifdef DEBUG_ZLIB
+#  include <stdio.h>
+#  ifndef verbose
+#    define verbose 0
+#  endif
+#  define Assert(cond, msg) {if(!(cond)) Trace(msg);}
+#  define Trace(x) printk(x)
+#  define Tracev(x) {if (verbose) printk x ;}
+#  define Tracevv(x) {if (verbose>1) printk x ;}
+#  define Tracec(c,x) {if (verbose && (c)) printk x ;}
+#  define Tracecv(c,x) {if (verbose>1 && (c)) printk x ;}
+#else
+#  define Assert(cond,msg)
+#  define Trace(x)
+#  define Tracev(x)
+#  define Tracevv(x)
+#  define Tracec(c,x)
+#  define Tracecv(c,x)
+#endif
+
+
+typedef uLong (*check_func) OF((uLong check, Bytef *buf, uInt len));
+
+/* voidpf zcalloc OF((voidpf opaque, unsigned items, unsigned size)); */
+/* void   zcfree  OF((voidpf opaque, voidpf ptr)); */
+
+#define ZALLOC(strm, items, size) \
+           (*((strm)->zalloc))((strm)->opaque, (items), (size))
+#define ZFREE(strm, addr, size)	\
+	   (*((strm)->zfree))((strm)->opaque, (voidpf)(addr), (size))
+#define TRY_FREE(s, p, n) {if (p) ZFREE(s, p, n);}
+
+/* deflate.h -- internal compression state
+ * Copyright (C) 1995 Jean-loup Gailly
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+/*+++++*/
+/* infblock.h -- header to use infblock.c
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+struct inflate_blocks_state;
+typedef struct inflate_blocks_state FAR inflate_blocks_statef;
+
+local inflate_blocks_statef * inflate_blocks_new OF((
+    z_stream *z,
+    check_func c,               /* check function */
+    uInt w));                   /* window size */
+
+local int inflate_blocks OF((
+    inflate_blocks_statef *,
+    z_stream *,
+    int));                      /* initial return code */
+
+local void inflate_blocks_reset OF((
+    inflate_blocks_statef *,
+    z_stream *,
+    uLongf *));                  /* check value on output */
+
+local int inflate_blocks_free OF((
+    inflate_blocks_statef *,
+    z_stream *,
+    uLongf *));                  /* check value on output */
+
+local int inflate_addhistory OF((
+    inflate_blocks_statef *,
+    z_stream *));
+
+local int inflate_packet_flush OF((
+    inflate_blocks_statef *));
+
+/*+++++*/
+/* inftrees.h -- header to use inftrees.c
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+/* Huffman code lookup table entry--this entry is four bytes for machines
+   that have 16-bit pointers (e.g. PC's in the small or medium model). */
+
+typedef struct inflate_huft_s FAR inflate_huft;
+
+struct inflate_huft_s {
+  union {
+    struct {
+      Byte Exop;        /* number of extra bits or operation */
+      Byte Bits;        /* number of bits in this code or subcode */
+    } what;
+    uInt Nalloc;	/* number of these allocated here */
+    Bytef *pad;         /* pad structure to a power of 2 (4 bytes for */
+  } word;               /*  16-bit, 8 bytes for 32-bit machines) */
+  union {
+    uInt Base;          /* literal, length base, or distance base */
+    inflate_huft *Next; /* pointer to next level of table */
+  } more;
+};
+
+#ifdef DEBUG_ZLIB
+  local uInt inflate_hufts;
+#endif
+
+local int inflate_trees_bits OF((
+    uIntf *,                    /* 19 code lengths */
+    uIntf *,                    /* bits tree desired/actual depth */
+    inflate_huft * FAR *,       /* bits tree result */
+    z_stream *));               /* for zalloc, zfree functions */
+
+local int inflate_trees_dynamic OF((
+    uInt,                       /* number of literal/length codes */
+    uInt,                       /* number of distance codes */
+    uIntf *,                    /* that many (total) code lengths */
+    uIntf *,                    /* literal desired/actual bit depth */
+    uIntf *,                    /* distance desired/actual bit depth */
+    inflate_huft * FAR *,       /* literal/length tree result */
+    inflate_huft * FAR *,       /* distance tree result */
+    z_stream *));               /* for zalloc, zfree functions */
+
+local int inflate_trees_fixed OF((
+    uIntf *,                    /* literal desired/actual bit depth */
+    uIntf *,                    /* distance desired/actual bit depth */
+    inflate_huft * FAR *,       /* literal/length tree result */
+    inflate_huft * FAR *));     /* distance tree result */
+
+local int inflate_trees_free OF((
+    inflate_huft *,             /* tables to free */
+    z_stream *));               /* for zfree function */
+
+
+/*+++++*/
+/* infcodes.h -- header to use infcodes.c
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+struct inflate_codes_state;
+typedef struct inflate_codes_state FAR inflate_codes_statef;
+
+local inflate_codes_statef *inflate_codes_new OF((
+    uInt, uInt,
+    inflate_huft *, inflate_huft *,
+    z_stream *));
+
+local int inflate_codes OF((
+    inflate_blocks_statef *,
+    z_stream *,
+    int));
+
+local void inflate_codes_free OF((
+    inflate_codes_statef *,
+    z_stream *));
+
+
+/*+++++*/
+/* inflate.c -- zlib interface to inflate modules
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* inflate private state */
+struct internal_state {
+
+  /* mode */
+  enum {
+      METHOD,   /* waiting for method byte */
+      FLAG,     /* waiting for flag byte */
+      BLOCKS,   /* decompressing blocks */
+      CHECK4,   /* four check bytes to go */
+      CHECK3,   /* three check bytes to go */
+      CHECK2,   /* two check bytes to go */
+      CHECK1,   /* one check byte to go */
+      DONE,     /* finished check, done */
+      BAD}      /* got an error--stay here */
+    mode;               /* current inflate mode */
+
+  /* mode dependent information */
+  union {
+    uInt method;        /* if FLAGS, method byte */
+    struct {
+      uLong was;                /* computed check value */
+      uLong need;               /* stream check value */
+    } check;            /* if CHECK, check values to compare */
+    uInt marker;        /* if BAD, inflateSync's marker bytes count */
+  } sub;        /* submode */
+
+  /* mode independent information */
+  int  nowrap;          /* flag for no wrapper */
+  uInt wbits;           /* log2(window size)  (8..15, defaults to 15) */
+  inflate_blocks_statef 
+    *blocks;            /* current inflate_blocks state */
+
+};
+
+
+int inflateReset(z)
+z_stream *z;
+{
+  uLong c;
+
+  if (z == Z_NULL || z->state == Z_NULL)
+    return Z_STREAM_ERROR;
+  z->total_in = z->total_out = 0;
+  z->msg = Z_NULL;
+  z->state->mode = z->state->nowrap ? BLOCKS : METHOD;
+  inflate_blocks_reset(z->state->blocks, z, &c);
+  Trace("inflate: reset\n");
+  return Z_OK;
+}
+
+
+int inflateEnd(z)
+z_stream *z;
+{
+  uLong c;
+
+  if (z == Z_NULL || z->state == Z_NULL || z->zfree == Z_NULL)
+    return Z_STREAM_ERROR;
+  if (z->state->blocks != Z_NULL)
+    inflate_blocks_free(z->state->blocks, z, &c);
+  ZFREE(z, z->state, sizeof(struct internal_state));
+  z->state = Z_NULL;
+  Trace("inflate: end\n");
+  return Z_OK;
+}
+
+
+int inflateInit2(z, w)
+z_stream *z;
+int w;
+{
+  /* initialize state */
+  if (z == Z_NULL)
+    return Z_STREAM_ERROR;
+/*  if (z->zalloc == Z_NULL) z->zalloc = zcalloc; */
+/*  if (z->zfree == Z_NULL) z->zfree = zcfree; */
+  if ((z->state = (struct internal_state FAR *)
+       ZALLOC(z,1,sizeof(struct internal_state))) == Z_NULL)
+    return Z_MEM_ERROR;
+  z->state->blocks = Z_NULL;
+
+  /* handle undocumented nowrap option (no zlib header or check) */
+  z->state->nowrap = 0;
+  if (w < 0)
+  {
+    w = - w;
+    z->state->nowrap = 1;
+  }
+
+  /* set window size */
+  if (w < 8 || w > 15)
+  {
+    inflateEnd(z);
+    return Z_STREAM_ERROR;
+  }
+  z->state->wbits = (uInt)w;
+
+  /* create inflate_blocks state */
+  if ((z->state->blocks =
+       inflate_blocks_new(z, z->state->nowrap ? Z_NULL : adler32, 1 << w))
+      == Z_NULL)
+  {
+    inflateEnd(z);
+    return Z_MEM_ERROR;
+  }
+  Trace("inflate: allocated\n");
+
+  /* reset state */
+  inflateReset(z);
+  return Z_OK;
+}
+
+
+int inflateInit(z)
+z_stream *z;
+{
+  return inflateInit2(z, DEF_WBITS);
+}
+
+
+#define NEEDBYTE {if(z->avail_in==0)goto empty;r=Z_OK;}
+#define NEXTBYTE (z->avail_in--,z->total_in++,*z->next_in++)
+
+int inflate(z, f)
+z_stream *z;
+int f;
+{
+  int r;
+  uInt b;
+
+  if (z == Z_NULL || z->next_in == Z_NULL)
+    return Z_STREAM_ERROR;
+  r = Z_BUF_ERROR;
+  while (1) switch (z->state->mode)
+  {
+    case METHOD:
+      NEEDBYTE
+      if (((z->state->sub.method = NEXTBYTE) & 0xf) != DEFLATED)
+      {
+        z->state->mode = BAD;
+        z->msg = "unknown compression method";
+        z->state->sub.marker = 5;       /* can't try inflateSync */
+        break;
+      }
+      if ((z->state->sub.method >> 4) + 8 > z->state->wbits)
+      {
+        z->state->mode = BAD;
+        z->msg = "invalid window size";
+        z->state->sub.marker = 5;       /* can't try inflateSync */
+        break;
+      }
+      z->state->mode = FLAG;
+    case FLAG:
+      NEEDBYTE
+      if ((b = NEXTBYTE) & 0x20)
+      {
+        z->state->mode = BAD;
+        z->msg = "invalid reserved bit";
+        z->state->sub.marker = 5;       /* can't try inflateSync */
+        break;
+      }
+      if (((z->state->sub.method << 8) + b) % 31)
+      {
+        z->state->mode = BAD;
+        z->msg = "incorrect header check";
+        z->state->sub.marker = 5;       /* can't try inflateSync */
+        break;
+      }
+      Trace("inflate: zlib header ok\n");
+      z->state->mode = BLOCKS;
+    case BLOCKS:
+      r = inflate_blocks(z->state->blocks, z, r);
+      if (f == Z_PACKET_FLUSH && z->avail_in == 0 && z->avail_out != 0)
+	  r = inflate_packet_flush(z->state->blocks);
+      if (r == Z_DATA_ERROR)
+      {
+        z->state->mode = BAD;
+        z->state->sub.marker = 0;       /* can try inflateSync */
+        break;
+      }
+      if (r != Z_STREAM_END)
+        return r;
+      r = Z_OK;
+      inflate_blocks_reset(z->state->blocks, z, &z->state->sub.check.was);
+      if (z->state->nowrap)
+      {
+        z->state->mode = DONE;
+        break;
+      }
+      z->state->mode = CHECK4;
+    case CHECK4:
+      NEEDBYTE
+      z->state->sub.check.need = (uLong)NEXTBYTE << 24;
+      z->state->mode = CHECK3;
+    case CHECK3:
+      NEEDBYTE
+      z->state->sub.check.need += (uLong)NEXTBYTE << 16;
+      z->state->mode = CHECK2;
+    case CHECK2:
+      NEEDBYTE
+      z->state->sub.check.need += (uLong)NEXTBYTE << 8;
+      z->state->mode = CHECK1;
+    case CHECK1:
+      NEEDBYTE
+      z->state->sub.check.need += (uLong)NEXTBYTE;
+
+      if (z->state->sub.check.was != z->state->sub.check.need)
+      {
+        z->state->mode = BAD;
+        z->msg = "incorrect data check";
+        z->state->sub.marker = 5;       /* can't try inflateSync */
+        break;
+      }
+      Trace( "inflate: zlib check ok\n");
+      z->state->mode = DONE;
+    case DONE:
+      return Z_STREAM_END;
+    case BAD:
+      return Z_DATA_ERROR;
+    default:
+      return Z_STREAM_ERROR;
+  }
+
+ empty:
+  if (f != Z_PACKET_FLUSH)
+    return r;
+  z->state->mode = BAD;
+  z->state->sub.marker = 0;       /* can try inflateSync */
+  return Z_DATA_ERROR;
+}
+
+/*
+ * This subroutine adds the data at next_in/avail_in to the output history
+ * without performing any output.  The output buffer must be "caught up";
+ * i.e. no pending output (hence s->read equals s->write), and the state must
+ * be BLOCKS (i.e. we should be willing to see the start of a series of
+ * BLOCKS).  On exit, the output will also be caught up, and the checksum
+ * will have been updated if need be.
+ */
+
+int inflateIncomp(z)
+z_stream *z;
+{
+    if (z->state->mode != BLOCKS)
+	return Z_DATA_ERROR;
+    return inflate_addhistory(z->state->blocks, z);
+}
+
+
+int inflateSync(z)
+z_stream *z;
+{
+  uInt n;       /* number of bytes to look at */
+  Bytef *p;     /* pointer to bytes */
+  uInt m;       /* number of marker bytes found in a row */
+  uLong r, w;   /* temporaries to save total_in and total_out */
+
+  /* set up */
+  if (z == Z_NULL || z->state == Z_NULL)
+    return Z_STREAM_ERROR;
+  if (z->state->mode != BAD)
+  {
+    z->state->mode = BAD;
+    z->state->sub.marker = 0;
+  }
+  if ((n = z->avail_in) == 0)
+    return Z_BUF_ERROR;
+  p = z->next_in;
+  m = z->state->sub.marker;
+
+  /* search */
+  while (n && m < 4)
+  {
+    if (*p == (Byte)(m < 2 ? 0 : 0xff))
+      m++;
+    else if (*p)
+      m = 0;
+    else
+      m = 4 - m;
+    p++, n--;
+  }
+
+  /* restore */
+  z->total_in += p - z->next_in;
+  z->next_in = p;
+  z->avail_in = n;
+  z->state->sub.marker = m;
+
+  /* return no joy or set up to restart on a new block */
+  if (m != 4)
+    return Z_DATA_ERROR;
+  r = z->total_in;  w = z->total_out;
+  inflateReset(z);
+  z->total_in = r;  z->total_out = w;
+  z->state->mode = BLOCKS;
+  return Z_OK;
+}
+
+#undef NEEDBYTE
+#undef NEXTBYTE
+
+/*+++++*/
+/* infutil.h -- types and macros common to blocks and codes
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+/* inflate blocks semi-private state */
+struct inflate_blocks_state {
+
+  /* mode */
+  enum {
+      TYPE,     /* get type bits (3, including end bit) */
+      LENS,     /* get lengths for stored */
+      STORED,   /* processing stored block */
+      TABLE,    /* get table lengths */
+      BTREE,    /* get bit lengths tree for a dynamic block */
+      DTREE,    /* get length, distance trees for a dynamic block */
+      CODES,    /* processing fixed or dynamic block */
+      DRY,      /* output remaining window bytes */
+      DONEB,     /* finished last block, done */
+      BADB}      /* got a data error--stuck here */
+    mode;               /* current inflate_block mode */
+
+  /* mode dependent information */
+  union {
+    uInt left;          /* if STORED, bytes left to copy */
+    struct {
+      uInt table;               /* table lengths (14 bits) */
+      uInt index;               /* index into blens (or border) */
+      uIntf *blens;             /* bit lengths of codes */
+      uInt bb;                  /* bit length tree depth */
+      inflate_huft *tb;         /* bit length decoding tree */
+      int nblens;		/* # elements allocated at blens */
+    } trees;            /* if DTREE, decoding info for trees */
+    struct {
+      inflate_huft *tl, *td;    /* trees to free */
+      inflate_codes_statef 
+         *codes;
+    } decode;           /* if CODES, current state */
+  } sub;                /* submode */
+  uInt last;            /* true if this block is the last block */
+
+  /* mode independent information */
+  uInt bitk;            /* bits in bit buffer */
+  uLong bitb;           /* bit buffer */
+  Bytef *window;        /* sliding window */
+  Bytef *end;           /* one byte after sliding window */
+  Bytef *read;          /* window read pointer */
+  Bytef *write;         /* window write pointer */
+  check_func checkfn;   /* check function */
+  uLong check;          /* check on output */
+
+};
+
+
+/* defines for inflate input/output */
+/*   update pointers and return */
+#define UPDBITS {s->bitb=b;s->bitk=k;}
+#define UPDIN {z->avail_in=n;z->total_in+=p-z->next_in;z->next_in=p;}
+#define UPDOUT {s->write=q;}
+#define UPDATE {UPDBITS UPDIN UPDOUT}
+#define LEAVE {UPDATE return inflate_flush(s,z,r);}
+/*   get bytes and bits */
+#define LOADIN {p=z->next_in;n=z->avail_in;b=s->bitb;k=s->bitk;}
+#define NEEDBYTE {if(n)r=Z_OK;else LEAVE}
+#define NEXTBYTE (n--,*p++)
+#define NEEDBITS(j) {while(k<(j)){NEEDBYTE;b|=((uLong)NEXTBYTE)<<k;k+=8;}}
+#define DUMPBITS(j) {b>>=(j);k-=(j);}
+/*   output bytes */
+#define WAVAIL (q<s->read?s->read-q-1:s->end-q)
+#define LOADOUT {q=s->write;m=WAVAIL;}
+#define WRAP {if(q==s->end&&s->read!=s->window){q=s->window;m=WAVAIL;}}
+#define FLUSH {UPDOUT r=inflate_flush(s,z,r); LOADOUT}
+#define NEEDOUT {if(m==0){WRAP if(m==0){FLUSH WRAP if(m==0) LEAVE}}r=Z_OK;}
+#define OUTBYTE(a) {*q++=(Byte)(a);m--;}
+/*   load local pointers */
+#define LOAD {LOADIN LOADOUT}
+
+/* And'ing with mask[n] masks the lower n bits */
+local uInt inflate_mask[] = {
+    0x0000,
+    0x0001, 0x0003, 0x0007, 0x000f, 0x001f, 0x003f, 0x007f, 0x00ff,
+    0x01ff, 0x03ff, 0x07ff, 0x0fff, 0x1fff, 0x3fff, 0x7fff, 0xffff
+};
+
+/* copy as much as possible from the sliding window to the output area */
+local int inflate_flush OF((
+    inflate_blocks_statef *,
+    z_stream *,
+    int));
+
+/*+++++*/
+/* inffast.h -- header to use inffast.c
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* WARNING: this file should *not* be used by applications. It is
+   part of the implementation of the compression library and is
+   subject to change. Applications should only use zlib.h.
+ */
+
+local int inflate_fast OF((
+    uInt,
+    uInt,
+    inflate_huft *,
+    inflate_huft *,
+    inflate_blocks_statef *,
+    z_stream *));
+
+
+/*+++++*/
+/* infblock.c -- interpret and process block types to last block
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* Table for deflate from PKZIP's appnote.txt. */
+local uInt border[] = { /* Order of the bit length code lengths */
+        16, 17, 18, 0, 8, 7, 9, 6, 10, 5, 11, 4, 12, 3, 13, 2, 14, 1, 15};
+
+/*
+   Notes beyond the 1.93a appnote.txt:
+
+   1. Distance pointers never point before the beginning of the output
+      stream.
+   2. Distance pointers can point back across blocks, up to 32k away.
+   3. There is an implied maximum of 7 bits for the bit length table and
+      15 bits for the actual data.
+   4. If only one code exists, then it is encoded using one bit.  (Zero
+      would be more efficient, but perhaps a little confusing.)  If two
+      codes exist, they are coded using one bit each (0 and 1).
+   5. There is no way of sending zero distance codes--a dummy must be
+      sent if there are none.  (History: a pre 2.0 version of PKZIP would
+      store blocks with no distance codes, but this was discovered to be
+      too harsh a criterion.)  Valid only for 1.93a.  2.04c does allow
+      zero distance codes, which is sent as one code of zero bits in
+      length.
+   6. There are up to 286 literal/length codes.  Code 256 represents the
+      end-of-block.  Note however that the static length tree defines
+      288 codes just to fill out the Huffman codes.  Codes 286 and 287
+      cannot be used though, since there is no length base or extra bits
+      defined for them.  Similarily, there are up to 30 distance codes.
+      However, static trees define 32 codes (all 5 bits) to fill out the
+      Huffman codes, but the last two had better not show up in the data.
+   7. Unzip can check dynamic Huffman blocks for complete code sets.
+      The exception is that a single code would not be complete (see #4).
+   8. The five bits following the block type is really the number of
+      literal codes sent minus 257.
+   9. Length codes 8,16,16 are interpreted as 13 length codes of 8 bits
+      (1+6+6).  Therefore, to output three times the length, you output
+      three codes (1+1+1), whereas to output four times the same length,
+      you only need two codes (1+3).  Hmm.
+  10. In the tree reconstruction algorithm, Code = Code + Increment
+      only if BitLength(i) is not zero.  (Pretty obvious.)
+  11. Correction: 4 Bits: # of Bit Length codes - 4     (4 - 19)
+  12. Note: length code 284 can represent 227-258, but length code 285
+      really is 258.  The last length deserves its own, short code
+      since it gets used a lot in very redundant files.  The length
+      258 is special since 258 - 3 (the min match length) is 255.
+  13. The literal/length and distance code bit lengths are read as a
+      single stream of lengths.  It is possible (and advantageous) for
+      a repeat code (16, 17, or 18) to go across the boundary between
+      the two sets of lengths.
+ */
+
+
+local void inflate_blocks_reset(s, z, c)
+inflate_blocks_statef *s;
+z_stream *z;
+uLongf *c;
+{
+  if (s->checkfn != Z_NULL)
+    *c = s->check;
+  if (s->mode == BTREE || s->mode == DTREE)
+    ZFREE(z, s->sub.trees.blens, s->sub.trees.nblens * sizeof(uInt));
+  if (s->mode == CODES)
+  {
+    inflate_codes_free(s->sub.decode.codes, z);
+    inflate_trees_free(s->sub.decode.td, z);
+    inflate_trees_free(s->sub.decode.tl, z);
+  }
+  s->mode = TYPE;
+  s->bitk = 0;
+  s->bitb = 0;
+  s->read = s->write = s->window;
+  if (s->checkfn != Z_NULL)
+    s->check = (*s->checkfn)(0L, Z_NULL, 0);
+  Trace("inflate:   blocks reset\n");
+}
+
+
+local inflate_blocks_statef *inflate_blocks_new(z, c, w)
+z_stream *z;
+check_func c;
+uInt w;
+{
+  inflate_blocks_statef *s;
+
+  if ((s = (inflate_blocks_statef *)ZALLOC
+       (z,1,sizeof(struct inflate_blocks_state))) == Z_NULL)
+    return s;
+  if ((s->window = (Bytef *)ZALLOC(z, 1, w)) == Z_NULL)
+  {
+    ZFREE(z, s, sizeof(struct inflate_blocks_state));
+    return Z_NULL;
+  }
+  s->end = s->window + w;
+  s->checkfn = c;
+  s->mode = TYPE;
+  Trace("inflate:   blocks allocated\n");
+  inflate_blocks_reset(s, z, &s->check);
+  return s;
+}
+
+
+local int inflate_blocks(s, z, r)
+inflate_blocks_statef *s;
+z_stream *z;
+int r;
+{
+  uInt t;               /* temporary storage */
+  uLong b;              /* bit buffer */
+  uInt k;               /* bits in bit buffer */
+  Bytef *p;             /* input data pointer */
+  uInt n;               /* bytes available there */
+  Bytef *q;             /* output window write pointer */
+  uInt m;               /* bytes to end of window or read pointer */
+
+  /* copy input/output information to locals (UPDATE macro restores) */
+  LOAD
+
+  /* process input based on current state */
+  while (1) switch (s->mode)
+  {
+    case TYPE:
+      NEEDBITS(3)
+      t = (uInt)b & 7;
+      s->last = t & 1;
+      switch (t >> 1)
+      {
+        case 0:                         /* stored */
+          Trace(("inflate:     stored block%s\n",
+                 s->last ? " (last)" : ""));
+          DUMPBITS(3)
+          t = k & 7;                    /* go to byte boundary */
+          DUMPBITS(t)
+          s->mode = LENS;               /* get length of stored block */
+          break;
+        case 1:                         /* fixed */
+          Trace(( "inflate:     fixed codes block%s\n",
+                 s->last ? " (last)" : ""));
+          {
+            uInt bl, bd;
+            inflate_huft *tl, *td;
+
+            inflate_trees_fixed(&bl, &bd, &tl, &td);
+            s->sub.decode.codes = inflate_codes_new(bl, bd, tl, td, z);
+            if (s->sub.decode.codes == Z_NULL)
+            {
+              r = Z_MEM_ERROR;
+              LEAVE
+            }
+            s->sub.decode.tl = Z_NULL;  /* don't try to free these */
+            s->sub.decode.td = Z_NULL;
+          }
+          DUMPBITS(3)
+          s->mode = CODES;
+          break;
+        case 2:                         /* dynamic */
+          Trace(( "inflate:     dynamic codes block%s\n",
+                 s->last ? " (last)" : ""));
+          DUMPBITS(3)
+          s->mode = TABLE;
+          break;
+        case 3:                         /* illegal */
+          DUMPBITS(3)
+          s->mode = BADB;
+          z->msg = "invalid block type";
+          r = Z_DATA_ERROR;
+          LEAVE
+      }
+      break;
+    case LENS:
+      NEEDBITS(32)
+      if (((~b) >> 16) != (b & 0xffff))
+      {
+        s->mode = BADB;
+        z->msg = "invalid stored block lengths";
+        r = Z_DATA_ERROR;
+        LEAVE
+      }
+      s->sub.left = (uInt)b & 0xffff;
+      b = k = 0;                      /* dump bits */
+      Tracev(( "inflate:       stored length %u\n", s->sub.left));
+      s->mode = s->sub.left ? STORED : TYPE;
+      break;
+    case STORED:
+      if (n == 0)
+        LEAVE
+      NEEDOUT
+      t = s->sub.left;
+      if (t > n) t = n;
+      if (t > m) t = m;
+      zmemcpy(q, p, t);
+      p += t;  n -= t;
+      q += t;  m -= t;
+      if ((s->sub.left -= t) != 0)
+        break;
+      Tracev(( "inflate:       stored end, %lu total out\n",
+              z->total_out + (q >= s->read ? q - s->read :
+              (s->end - s->read) + (q - s->window))));
+      s->mode = s->last ? DRY : TYPE;
+      break;
+    case TABLE:
+      NEEDBITS(14)
+      s->sub.trees.table = t = (uInt)b & 0x3fff;
+#ifndef PKZIP_BUG_WORKAROUND
+      if ((t & 0x1f) > 29 || ((t >> 5) & 0x1f) > 29)
+      {
+        s->mode = BADB;
+        z->msg = "too many length or distance symbols";
+        r = Z_DATA_ERROR;
+        LEAVE
+      }
+#endif
+      t = 258 + (t & 0x1f) + ((t >> 5) & 0x1f);
+      if (t < 19)
+        t = 19;
+      if ((s->sub.trees.blens = (uIntf*)ZALLOC(z, t, sizeof(uInt))) == Z_NULL)
+      {
+        r = Z_MEM_ERROR;
+        LEAVE
+      }
+      s->sub.trees.nblens = t;
+      DUMPBITS(14)
+      s->sub.trees.index = 0;
+      Tracev(( "inflate:       table sizes ok\n"));
+      s->mode = BTREE;
+    case BTREE:
+      while (s->sub.trees.index < 4 + (s->sub.trees.table >> 10))
+      {
+        NEEDBITS(3)
+        s->sub.trees.blens[border[s->sub.trees.index++]] = (uInt)b & 7;
+        DUMPBITS(3)
+      }
+      while (s->sub.trees.index < 19)
+        s->sub.trees.blens[border[s->sub.trees.index++]] = 0;
+      s->sub.trees.bb = 7;
+      t = inflate_trees_bits(s->sub.trees.blens, &s->sub.trees.bb,
+                             &s->sub.trees.tb, z);
+      if (t != Z_OK)
+      {
+        r = t;
+        if (r == Z_DATA_ERROR)
+          s->mode = BADB;
+        LEAVE
+      }
+      s->sub.trees.index = 0;
+      Tracev(( "inflate:       bits tree ok\n"));
+      s->mode = DTREE;
+    case DTREE:
+      while (t = s->sub.trees.table,
+             s->sub.trees.index < 258 + (t & 0x1f) + ((t >> 5) & 0x1f))
+      {
+        inflate_huft *h;
+        uInt i, j, c;
+
+        t = s->sub.trees.bb;
+        NEEDBITS(t)
+        h = s->sub.trees.tb + ((uInt)b & inflate_mask[t]);
+        t = h->word.what.Bits;
+        c = h->more.Base;
+        if (c < 16)
+        {
+          DUMPBITS(t)
+          s->sub.trees.blens[s->sub.trees.index++] = c;
+        }
+        else /* c == 16..18 */
+        {
+          i = c == 18 ? 7 : c - 14;
+          j = c == 18 ? 11 : 3;
+          NEEDBITS(t + i)
+          DUMPBITS(t)
+          j += (uInt)b & inflate_mask[i];
+          DUMPBITS(i)
+          i = s->sub.trees.index;
+          t = s->sub.trees.table;
+          if (i + j > 258 + (t & 0x1f) + ((t >> 5) & 0x1f) ||
+              (c == 16 && i < 1))
+          {
+            s->mode = BADB;
+            z->msg = "invalid bit length repeat";
+            r = Z_DATA_ERROR;
+            LEAVE
+          }
+          c = c == 16 ? s->sub.trees.blens[i - 1] : 0;
+          do {
+            s->sub.trees.blens[i++] = c;
+          } while (--j);
+          s->sub.trees.index = i;
+        }
+      }
+      inflate_trees_free(s->sub.trees.tb, z);
+      s->sub.trees.tb = Z_NULL;
+      {
+        uInt bl, bd;
+        inflate_huft *tl, *td;
+        inflate_codes_statef *c;
+
+        bl = 9;         /* must be <= 9 for lookahead assumptions */
+        bd = 6;         /* must be <= 9 for lookahead assumptions */
+        t = s->sub.trees.table;
+        t = inflate_trees_dynamic(257 + (t & 0x1f), 1 + ((t >> 5) & 0x1f),
+                                  s->sub.trees.blens, &bl, &bd, &tl, &td, z);
+        if (t != Z_OK)
+        {
+          if (t == (uInt)Z_DATA_ERROR)
+            s->mode = BADB;
+          r = t;
+          LEAVE
+        }
+        Tracev(( "inflate:       trees ok\n"));
+        if ((c = inflate_codes_new(bl, bd, tl, td, z)) == Z_NULL)
+        {
+          inflate_trees_free(td, z);
+          inflate_trees_free(tl, z);
+          r = Z_MEM_ERROR;
+          LEAVE
+        }
+        ZFREE(z, s->sub.trees.blens, s->sub.trees.nblens * sizeof(uInt));
+        s->sub.decode.codes = c;
+        s->sub.decode.tl = tl;
+        s->sub.decode.td = td;
+      }
+      s->mode = CODES;
+    case CODES:
+      UPDATE
+      if ((r = inflate_codes(s, z, r)) != Z_STREAM_END)
+        return inflate_flush(s, z, r);
+      r = Z_OK;
+      inflate_codes_free(s->sub.decode.codes, z);
+      inflate_trees_free(s->sub.decode.td, z);
+      inflate_trees_free(s->sub.decode.tl, z);
+      LOAD
+      Tracev(( "inflate:       codes end, %lu total out\n",
+              z->total_out + (q >= s->read ? q - s->read :
+              (s->end - s->read) + (q - s->window))));
+      if (!s->last)
+      {
+        s->mode = TYPE;
+        break;
+      }
+      if (k > 7)              /* return unused byte, if any */
+      {
+        Assert(k < 16, "inflate_codes grabbed too many bytes")
+        k -= 8;
+        n++;
+        p--;                    /* can always return one */
+      }
+      s->mode = DRY;
+    case DRY:
+      FLUSH
+      if (s->read != s->write)
+        LEAVE
+      s->mode = DONEB;
+    case DONEB:
+      r = Z_STREAM_END;
+      LEAVE
+    case BADB:
+      r = Z_DATA_ERROR;
+      LEAVE
+    default:
+      r = Z_STREAM_ERROR;
+      LEAVE
+  }
+}
+
+
+local int inflate_blocks_free(s, z, c)
+inflate_blocks_statef *s;
+z_stream *z;
+uLongf *c;
+{
+  inflate_blocks_reset(s, z, c);
+  ZFREE(z, s->window, s->end - s->window);
+  ZFREE(z, s, sizeof(struct inflate_blocks_state));
+  Trace(( "inflate:   blocks freed\n"));
+  return Z_OK;
+}
+
+/*
+ * This subroutine adds the data at next_in/avail_in to the output history
+ * without performing any output.  The output buffer must be "caught up";
+ * i.e. no pending output (hence s->read equals s->write), and the state must
+ * be BLOCKS (i.e. we should be willing to see the start of a series of
+ * BLOCKS).  On exit, the output will also be caught up, and the checksum
+ * will have been updated if need be.
+ */
+local int inflate_addhistory(s, z)
+inflate_blocks_statef *s;
+z_stream *z;
+{
+    uLong b;              /* bit buffer */  /* NOT USED HERE */
+    uInt k;               /* bits in bit buffer */ /* NOT USED HERE */
+    uInt t;               /* temporary storage */
+    Bytef *p;             /* input data pointer */
+    uInt n;               /* bytes available there */
+    Bytef *q;             /* output window write pointer */
+    uInt m;               /* bytes to end of window or read pointer */
+
+    if (s->read != s->write)
+	return Z_STREAM_ERROR;
+    if (s->mode != TYPE)
+	return Z_DATA_ERROR;
+
+    /* we're ready to rock */
+    LOAD
+    /* while there is input ready, copy to output buffer, moving
+     * pointers as needed.
+     */
+    while (n) {
+	t = n;  /* how many to do */
+	/* is there room until end of buffer? */
+	if (t > m) t = m;
+	/* update check information */
+	if (s->checkfn != Z_NULL)
+	    s->check = (*s->checkfn)(s->check, q, t);
+	zmemcpy(q, p, t);
+	q += t;
+	p += t;
+	n -= t;
+	z->total_out += t;
+	s->read = q;    /* drag read pointer forward */
+/*      WRAP  */ 	/* expand WRAP macro by hand to handle s->read */
+	if (q == s->end) {
+	    s->read = q = s->window;
+	    m = WAVAIL;
+	}
+    }
+    UPDATE
+    return Z_OK;
+}
+
+
+/*
+ * At the end of a Deflate-compressed PPP packet, we expect to have seen
+ * a `stored' block type value but not the (zero) length bytes.
+ */
+local int inflate_packet_flush(s)
+    inflate_blocks_statef *s;
+{
+    if (s->mode != LENS)
+	return Z_DATA_ERROR;
+    s->mode = TYPE;
+    return Z_OK;
+}
+
+
+/*+++++*/
+/* inftrees.c -- generate Huffman trees for efficient decoding
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* simplify the use of the inflate_huft type with some defines */
+#define base more.Base
+#define next more.Next
+#define exop word.what.Exop
+#define bits word.what.Bits
+
+
+local int huft_build OF((
+    uIntf *,            /* code lengths in bits */
+    uInt,               /* number of codes */
+    uInt,               /* number of "simple" codes */
+    uIntf *,            /* list of base values for non-simple codes */
+    uIntf *,            /* list of extra bits for non-simple codes */
+    inflate_huft * FAR*,/* result: starting table */
+    uIntf *,            /* maximum lookup bits (returns actual) */
+    z_stream *));       /* for zalloc function */
+
+local voidpf falloc OF((
+    voidpf,             /* opaque pointer (not used) */
+    uInt,               /* number of items */
+    uInt));             /* size of item */
+
+local void ffree OF((
+    voidpf q,           /* opaque pointer (not used) */
+    voidpf p,           /* what to free (not used) */
+    uInt n));		/* number of bytes (not used) */
+
+/* Tables for deflate from PKZIP's appnote.txt. */
+local uInt cplens[] = { /* Copy lengths for literal codes 257..285 */
+        3, 4, 5, 6, 7, 8, 9, 10, 11, 13, 15, 17, 19, 23, 27, 31,
+        35, 43, 51, 59, 67, 83, 99, 115, 131, 163, 195, 227, 258, 0, 0};
+        /* actually lengths - 2; also see note #13 above about 258 */
+local uInt cplext[] = { /* Extra bits for literal codes 257..285 */
+        0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 2, 2, 2, 2,
+        3, 3, 3, 3, 4, 4, 4, 4, 5, 5, 5, 5, 0, 192, 192}; /* 192==invalid */
+local uInt cpdist[] = { /* Copy offsets for distance codes 0..29 */
+        1, 2, 3, 4, 5, 7, 9, 13, 17, 25, 33, 49, 65, 97, 129, 193,
+        257, 385, 513, 769, 1025, 1537, 2049, 3073, 4097, 6145,
+        8193, 12289, 16385, 24577};
+local uInt cpdext[] = { /* Extra bits for distance codes */
+        0, 0, 0, 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6,
+        7, 7, 8, 8, 9, 9, 10, 10, 11, 11,
+        12, 12, 13, 13};
+
+/*
+   Huffman code decoding is performed using a multi-level table lookup.
+   The fastest way to decode is to simply build a lookup table whose
+   size is determined by the longest code.  However, the time it takes
+   to build this table can also be a factor if the data being decoded
+   is not very long.  The most common codes are necessarily the
+   shortest codes, so those codes dominate the decoding time, and hence
+   the speed.  The idea is you can have a shorter table that decodes the
+   shorter, more probable codes, and then point to subsidiary tables for
+   the longer codes.  The time it costs to decode the longer codes is
+   then traded against the time it takes to make longer tables.
+
+   This results of this trade are in the variables lbits and dbits
+   below.  lbits is the number of bits the first level table for literal/
+   length codes can decode in one step, and dbits is the same thing for
+   the distance codes.  Subsequent tables are also less than or equal to
+   those sizes.  These values may be adjusted either when all of the
+   codes are shorter than that, in which case the longest code length in
+   bits is used, or when the shortest code is *longer* than the requested
+   table size, in which case the length of the shortest code in bits is
+   used.
+
+   There are two different values for the two tables, since they code a
+   different number of possibilities each.  The literal/length table
+   codes 286 possible values, or in a flat code, a little over eight
+   bits.  The distance table codes 30 possible values, or a little less
+   than five bits, flat.  The optimum values for speed end up being
+   about one bit more than those, so lbits is 8+1 and dbits is 5+1.
+   The optimum values may differ though from machine to machine, and
+   possibly even between compilers.  Your mileage may vary.
+ */
+
+
+/* If BMAX needs to be larger than 16, then h and x[] should be uLong. */
+#define BMAX 15         /* maximum bit length of any code */
+#define N_MAX 288       /* maximum number of codes in any set */
+
+#ifdef DEBUG_ZLIB
+  uInt inflate_hufts;
+#endif
+
+local int huft_build(b, n, s, d, e, t, m, zs)
+uIntf *b;               /* code lengths in bits (all assumed <= BMAX) */
+uInt n;                 /* number of codes (assumed <= N_MAX) */
+uInt s;                 /* number of simple-valued codes (0..s-1) */
+uIntf *d;               /* list of base values for non-simple codes */
+uIntf *e;               /* list of extra bits for non-simple codes */  
+inflate_huft * FAR *t;  /* result: starting table */
+uIntf *m;               /* maximum lookup bits, returns actual */
+z_stream *zs;           /* for zalloc function */
+/* Given a list of code lengths and a maximum table size, make a set of
+   tables to decode that set of codes.  Return Z_OK on success, Z_BUF_ERROR
+   if the given code set is incomplete (the tables are still built in this
+   case), Z_DATA_ERROR if the input is invalid (all zero length codes or an
+   over-subscribed set of lengths), or Z_MEM_ERROR if not enough memory. */
+{
+
+  uInt a;                       /* counter for codes of length k */
+  uInt c[BMAX+1];               /* bit length count table */
+  uInt f;                       /* i repeats in table every f entries */
+  int g;                        /* maximum code length */
+  int h;                        /* table level */
+  register uInt i;              /* counter, current code */
+  register uInt j;              /* counter */
+  register int k;               /* number of bits in current code */
+  int l;                        /* bits per table (returned in m) */
+  register uIntf *p;            /* pointer into c[], b[], or v[] */
+  inflate_huft *q;              /* points to current table */
+  struct inflate_huft_s r;      /* table entry for structure assignment */
+  inflate_huft *u[BMAX];        /* table stack */
+  uInt v[N_MAX];                /* values in order of bit length */
+  register int w;               /* bits before this table == (l * h) */
+  uInt x[BMAX+1];               /* bit offsets, then code stack */
+  uIntf *xp;                    /* pointer into x */
+  int y;                        /* number of dummy codes added */
+  uInt z;                       /* number of entries in current table */
+
+
+  /* Generate counts for each bit length */
+  p = c;
+#define C0 *p++ = 0;
+#define C2 C0 C0 C0 C0
+#define C4 C2 C2 C2 C2
+  C4                            /* clear c[]--assume BMAX+1 is 16 */
+  p = b;  i = n;
+  do {
+    c[*p++]++;                  /* assume all entries <= BMAX */
+  } while (--i);
+  if (c[0] == n)                /* null input--all zero length codes */
+  {
+    *t = (inflate_huft *)Z_NULL;
+    *m = 0;
+    return Z_OK;
+  }
+
+
+  /* Find minimum and maximum length, bound *m by those */
+  l = *m;
+  for (j = 1; j <= BMAX; j++)
+    if (c[j])
+      break;
+  k = j;                        /* minimum code length */
+  if ((uInt)l < j)
+    l = j;
+  for (i = BMAX; i; i--)
+    if (c[i])
+      break;
+  g = i;                        /* maximum code length */
+  if ((uInt)l > i)
+    l = i;
+  *m = l;
+
+
+  /* Adjust last length count to fill out codes, if needed */
+  for (y = 1 << j; j < i; j++, y <<= 1)
+    if ((y -= c[j]) < 0)
+      return Z_DATA_ERROR;
+  if ((y -= c[i]) < 0)
+    return Z_DATA_ERROR;
+  c[i] += y;
+
+
+  /* Generate starting offsets into the value table for each length */
+  x[1] = j = 0;
+  p = c + 1;  xp = x + 2;
+  while (--i) {                 /* note that i == g from above */
+    *xp++ = (j += *p++);
+  }
+
+
+  /* Make a table of values in order of bit lengths */
+  p = b;  i = 0;
+  do {
+    if ((j = *p++) != 0)
+      v[x[j]++] = i;
+  } while (++i < n);
+
+
+  /* Generate the Huffman codes and for each, make the table entries */
+  x[0] = i = 0;                 /* first Huffman code is zero */
+  p = v;                        /* grab values in bit order */
+  h = -1;                       /* no tables yet--level -1 */
+  w = -l;                       /* bits decoded == (l * h) */
+  u[0] = (inflate_huft *)Z_NULL;        /* just to keep compilers happy */
+  q = (inflate_huft *)Z_NULL;   /* ditto */
+  z = 0;                        /* ditto */
+
+  /* go through the bit lengths (k already is bits in shortest code) */
+  for (; k <= g; k++)
+  {
+    a = c[k];
+    while (a--)
+    {
+      /* here i is the Huffman code of length k bits for value *p */
+      /* make tables up to required level */
+      while (k > w + l)
+      {
+        h++;
+        w += l;                 /* previous table always l bits */
+
+        /* compute minimum size table less than or equal to l bits */
+        z = (z = g - w) > (uInt)l ? l : z;      /* table size upper limit */
+        if ((f = 1 << (j = k - w)) > a + 1)     /* try a k-w bit table */
+        {                       /* too few codes for k-w bit table */
+          f -= a + 1;           /* deduct codes from patterns left */
+          xp = c + k;
+          if (j < z)
+            while (++j < z)     /* try smaller tables up to z bits */
+            {
+              if ((f <<= 1) <= *++xp)
+                break;          /* enough codes to use up j bits */
+              f -= *xp;         /* else deduct codes from patterns */
+            }
+        }
+        z = 1 << j;             /* table entries for j-bit table */
+
+        /* allocate and link in new table */
+        if ((q = (inflate_huft *)ZALLOC
+             (zs,z + 1,sizeof(inflate_huft))) == Z_NULL)
+        {
+          if (h)
+            inflate_trees_free(u[0], zs);
+          return Z_MEM_ERROR;   /* not enough memory */
+        }
+	q->word.Nalloc = z + 1;
+#ifdef DEBUG_ZLIB
+        inflate_hufts += z + 1;
+#endif
+        *t = q + 1;             /* link to list for huft_free() */
+        *(t = &(q->next)) = Z_NULL;
+        u[h] = ++q;             /* table starts after link */
+
+        /* connect to last table, if there is one */
+        if (h)
+        {
+          x[h] = i;             /* save pattern for backing up */
+          r.bits = (Byte)l;     /* bits to dump before this table */
+          r.exop = (Byte)j;     /* bits in this table */
+          r.next = q;           /* pointer to this table */
+          j = i >> (w - l);     /* (get around Turbo C bug) */
+          u[h-1][j] = r;        /* connect to last table */
+        }
+      }
+
+      /* set up table entry in r */
+      r.bits = (Byte)(k - w);
+      if (p >= v + n)
+        r.exop = 128 + 64;      /* out of values--invalid code */
+      else if (*p < s)
+      {
+        r.exop = (Byte)(*p < 256 ? 0 : 32 + 64);     /* 256 is end-of-block */
+        r.base = *p++;          /* simple code is just the value */
+      }
+      else
+      {
+        r.exop = (Byte)e[*p - s] + 16 + 64; /* non-simple--look up in lists */
+        r.base = d[*p++ - s];
+      }
+
+      /* fill code-like entries with r */
+      f = 1 << (k - w);
+      for (j = i >> w; j < z; j += f)
+        q[j] = r;
+
+      /* backwards increment the k-bit code i */
+      for (j = 1 << (k - 1); i & j; j >>= 1)
+        i ^= j;
+      i ^= j;
+
+      /* backup over finished tables */
+      while ((i & ((1 << w) - 1)) != x[h])
+      {
+        h--;                    /* don't need to update q */
+        w -= l;
+      }
+    }
+  }
+
+
+  /* Return Z_BUF_ERROR if we were given an incomplete table */
+  return y != 0 && g != 1 ? Z_BUF_ERROR : Z_OK;
+}
+
+
+local int inflate_trees_bits(c, bb, tb, z)
+uIntf *c;               /* 19 code lengths */
+uIntf *bb;              /* bits tree desired/actual depth */
+inflate_huft * FAR *tb; /* bits tree result */
+z_stream *z;            /* for zfree function */
+{
+  int r;
+
+  r = huft_build(c, 19, 19, (uIntf*)Z_NULL, (uIntf*)Z_NULL, tb, bb, z);
+  if (r == Z_DATA_ERROR)
+    z->msg = "oversubscribed dynamic bit lengths tree";
+  else if (r == Z_BUF_ERROR)
+  {
+    inflate_trees_free(*tb, z);
+    z->msg = "incomplete dynamic bit lengths tree";
+    r = Z_DATA_ERROR;
+  }
+  return r;
+}
+
+
+local int inflate_trees_dynamic(nl, nd, c, bl, bd, tl, td, z)
+uInt nl;                /* number of literal/length codes */
+uInt nd;                /* number of distance codes */
+uIntf *c;               /* that many (total) code lengths */
+uIntf *bl;              /* literal desired/actual bit depth */
+uIntf *bd;              /* distance desired/actual bit depth */
+inflate_huft * FAR *tl; /* literal/length tree result */
+inflate_huft * FAR *td; /* distance tree result */
+z_stream *z;            /* for zfree function */
+{
+  int r;
+
+  /* build literal/length tree */
+  if ((r = huft_build(c, nl, 257, cplens, cplext, tl, bl, z)) != Z_OK)
+  {
+    if (r == Z_DATA_ERROR)
+      z->msg = "oversubscribed literal/length tree";
+    else if (r == Z_BUF_ERROR)
+    {
+      inflate_trees_free(*tl, z);
+      z->msg = "incomplete literal/length tree";
+      r = Z_DATA_ERROR;
+    }
+    return r;
+  }
+
+  /* build distance tree */
+  if ((r = huft_build(c + nl, nd, 0, cpdist, cpdext, td, bd, z)) != Z_OK)
+  {
+    if (r == Z_DATA_ERROR)
+      z->msg = "oversubscribed literal/length tree";
+    else if (r == Z_BUF_ERROR) {
+#ifdef PKZIP_BUG_WORKAROUND
+      r = Z_OK;
+    }
+#else
+      inflate_trees_free(*td, z);
+      z->msg = "incomplete literal/length tree";
+      r = Z_DATA_ERROR;
+    }
+    inflate_trees_free(*tl, z);
+    return r;
+#endif
+  }
+
+  /* done */
+  return Z_OK;
+}
+
+
+/* build fixed tables only once--keep them here */
+local int fixed_lock = 0;
+local int fixed_built = 0;
+#define FIXEDH 530      /* number of hufts used by fixed tables */
+local uInt fixed_left = FIXEDH;
+local inflate_huft fixed_mem[FIXEDH];
+local uInt fixed_bl;
+local uInt fixed_bd;
+local inflate_huft *fixed_tl;
+local inflate_huft *fixed_td;
+
+
+local voidpf falloc(q, n, s)
+voidpf q;        /* opaque pointer (not used) */
+uInt n;         /* number of items */
+uInt s;         /* size of item */
+{
+  Assert(s == sizeof(inflate_huft) && n <= fixed_left,
+         "inflate_trees falloc overflow");
+  if (q) s++; /* to make some compilers happy */
+  fixed_left -= n;
+  return (voidpf)(fixed_mem + fixed_left);
+}
+
+
+local void ffree(q, p, n)
+voidpf q;
+voidpf p;
+uInt n;
+{
+  Assert(0, "inflate_trees ffree called!");
+  if (q) q = p; /* to make some compilers happy */
+}
+
+
+local int inflate_trees_fixed(bl, bd, tl, td)
+uIntf *bl;               /* literal desired/actual bit depth */
+uIntf *bd;               /* distance desired/actual bit depth */
+inflate_huft * FAR *tl;  /* literal/length tree result */
+inflate_huft * FAR *td;  /* distance tree result */
+{
+  /* build fixed tables if not built already--lock out other instances */
+  while (++fixed_lock > 1)
+    fixed_lock--;
+  if (!fixed_built)
+  {
+    int k;              /* temporary variable */
+    unsigned c[288];    /* length list for huft_build */
+    z_stream z;         /* for falloc function */
+
+    /* set up fake z_stream for memory routines */
+    z.zalloc = falloc;
+    z.zfree = ffree;
+    z.opaque = Z_NULL;
+
+    /* literal table */
+    for (k = 0; k < 144; k++)
+      c[k] = 8;
+    for (; k < 256; k++)
+      c[k] = 9;
+    for (; k < 280; k++)
+      c[k] = 7;
+    for (; k < 288; k++)
+      c[k] = 8;
+    fixed_bl = 7;
+    huft_build(c, 288, 257, cplens, cplext, &fixed_tl, &fixed_bl, &z);
+
+    /* distance table */
+    for (k = 0; k < 30; k++)
+      c[k] = 5;
+    fixed_bd = 5;
+    huft_build(c, 30, 0, cpdist, cpdext, &fixed_td, &fixed_bd, &z);
+
+    /* done */
+    fixed_built = 1;
+  }
+  fixed_lock--;
+  *bl = fixed_bl;
+  *bd = fixed_bd;
+  *tl = fixed_tl;
+  *td = fixed_td;
+  return Z_OK;
+}
+
+
+local int inflate_trees_free(t, z)
+inflate_huft *t;        /* table to free */
+z_stream *z;            /* for zfree function */
+/* Free the malloc'ed tables built by huft_build(), which makes a linked
+   list of the tables it made, with the links in a dummy first entry of
+   each table. */
+{
+  register inflate_huft *p, *q;
+
+  /* Go through linked list, freeing from the malloced (t[-1]) address. */
+  p = t;
+  while (p != Z_NULL)
+  {
+    q = (--p)->next;
+    ZFREE(z, p, p->word.Nalloc * sizeof(inflate_huft));
+    p = q;
+  } 
+  return Z_OK;
+}
+
+/*+++++*/
+/* infcodes.c -- process literals and length/distance pairs
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* simplify the use of the inflate_huft type with some defines */
+#define base more.Base
+#define next more.Next
+#define exop word.what.Exop
+#define bits word.what.Bits
+
+/* inflate codes private state */
+struct inflate_codes_state {
+
+  /* mode */
+  enum {        /* waiting for "i:"=input, "o:"=output, "x:"=nothing */
+      START,    /* x: set up for LEN */
+      LEN,      /* i: get length/literal/eob next */
+      LENEXT,   /* i: getting length extra (have base) */
+      DIST,     /* i: get distance next */
+      DISTEXT,  /* i: getting distance extra */
+      COPY,     /* o: copying bytes in window, waiting for space */
+      LIT,      /* o: got literal, waiting for output space */
+      WASH,     /* o: got eob, possibly still output waiting */
+      END,      /* x: got eob and all data flushed */
+      BADCODE}  /* x: got error */
+    mode;               /* current inflate_codes mode */
+
+  /* mode dependent information */
+  uInt len;
+  union {
+    struct {
+      inflate_huft *tree;       /* pointer into tree */
+      uInt need;                /* bits needed */
+    } code;             /* if LEN or DIST, where in tree */
+    uInt lit;           /* if LIT, literal */
+    struct {
+      uInt get;                 /* bits to get for extra */
+      uInt dist;                /* distance back to copy from */
+    } copy;             /* if EXT or COPY, where and how much */
+  } sub;                /* submode */
+
+  /* mode independent information */
+  Byte lbits;           /* ltree bits decoded per branch */
+  Byte dbits;           /* dtree bits decoder per branch */
+  inflate_huft *ltree;          /* literal/length/eob tree */
+  inflate_huft *dtree;          /* distance tree */
+
+};
+
+
+local inflate_codes_statef *inflate_codes_new(bl, bd, tl, td, z)
+uInt bl, bd;
+inflate_huft *tl, *td;
+z_stream *z;
+{
+  inflate_codes_statef *c;
+
+  if ((c = (inflate_codes_statef *)
+       ZALLOC(z,1,sizeof(struct inflate_codes_state))) != Z_NULL)
+  {
+    c->mode = START;
+    c->lbits = (Byte)bl;
+    c->dbits = (Byte)bd;
+    c->ltree = tl;
+    c->dtree = td;
+    Tracev(( "inflate:       codes new\n"));
+  }
+  return c;
+}
+
+
+local int inflate_codes(s, z, r)
+inflate_blocks_statef *s;
+z_stream *z;
+int r;
+{
+  uInt j;               /* temporary storage */
+  inflate_huft *t;      /* temporary pointer */
+  uInt e;               /* extra bits or operation */
+  uLong b;              /* bit buffer */
+  uInt k;               /* bits in bit buffer */
+  Bytef *p;             /* input data pointer */
+  uInt n;               /* bytes available there */
+  Bytef *q;             /* output window write pointer */
+  uInt m;               /* bytes to end of window or read pointer */
+  Bytef *f;             /* pointer to copy strings from */
+  inflate_codes_statef *c = s->sub.decode.codes;  /* codes state */
+
+  /* copy input/output information to locals (UPDATE macro restores) */
+  LOAD
+
+  /* process input and output based on current state */
+  while (1) switch (c->mode)
+  {             /* waiting for "i:"=input, "o:"=output, "x:"=nothing */
+    case START:         /* x: set up for LEN */
+#ifndef SLOW
+      if (m >= 258 && n >= 10)
+      {
+        UPDATE
+        r = inflate_fast(c->lbits, c->dbits, c->ltree, c->dtree, s, z);
+        LOAD
+        if (r != Z_OK)
+        {
+          c->mode = r == Z_STREAM_END ? WASH : BADCODE;
+          break;
+        }
+      }
+#endif /* !SLOW */
+      c->sub.code.need = c->lbits;
+      c->sub.code.tree = c->ltree;
+      c->mode = LEN;
+    case LEN:           /* i: get length/literal/eob next */
+      j = c->sub.code.need;
+      NEEDBITS(j)
+      t = c->sub.code.tree + ((uInt)b & inflate_mask[j]);
+      DUMPBITS(t->bits)
+      e = (uInt)(t->exop);
+      if (e == 0)               /* literal */
+      {
+        c->sub.lit = t->base;
+        Tracevv(( t->base >= 0x20 && t->base < 0x7f ?
+                 "inflate:         literal '%c'\n" :
+                 "inflate:         literal 0x%02x\n", t->base));
+        c->mode = LIT;
+        break;
+      }
+      if (e & 16)               /* length */
+      {
+        c->sub.copy.get = e & 15;
+        c->len = t->base;
+        c->mode = LENEXT;
+        break;
+      }
+      if ((e & 64) == 0)        /* next table */
+      {
+        c->sub.code.need = e;
+        c->sub.code.tree = t->next;
+        break;
+      }
+      if (e & 32)               /* end of block */
+      {
+        Tracevv(( "inflate:         end of block\n"));
+        c->mode = WASH;
+        break;
+      }
+      c->mode = BADCODE;        /* invalid code */
+      z->msg = "invalid literal/length code";
+      r = Z_DATA_ERROR;
+      LEAVE
+    case LENEXT:        /* i: getting length extra (have base) */
+      j = c->sub.copy.get;
+      NEEDBITS(j)
+      c->len += (uInt)b & inflate_mask[j];
+      DUMPBITS(j)
+      c->sub.code.need = c->dbits;
+      c->sub.code.tree = c->dtree;
+      Tracevv(( "inflate:         length %u\n", c->len));
+      c->mode = DIST;
+    case DIST:          /* i: get distance next */
+      j = c->sub.code.need;
+      NEEDBITS(j)
+      t = c->sub.code.tree + ((uInt)b & inflate_mask[j]);
+      DUMPBITS(t->bits)
+      e = (uInt)(t->exop);
+      if (e & 16)               /* distance */
+      {
+        c->sub.copy.get = e & 15;
+        c->sub.copy.dist = t->base;
+        c->mode = DISTEXT;
+        break;
+      }
+      if ((e & 64) == 0)        /* next table */
+      {
+        c->sub.code.need = e;
+        c->sub.code.tree = t->next;
+        break;
+      }
+      c->mode = BADCODE;        /* invalid code */
+      z->msg = "invalid distance code";
+      r = Z_DATA_ERROR;
+      LEAVE
+    case DISTEXT:       /* i: getting distance extra */
+      j = c->sub.copy.get;
+      NEEDBITS(j)
+      c->sub.copy.dist += (uInt)b & inflate_mask[j];
+      DUMPBITS(j)
+      Tracevv(( "inflate:         distance %u\n", c->sub.copy.dist));
+      c->mode = COPY;
+    case COPY:          /* o: copying bytes in window, waiting for space */
+#ifndef __TURBOC__ /* Turbo C bug for following expression */
+      f = (uInt)(q - s->window) < c->sub.copy.dist ?
+          s->end - (c->sub.copy.dist - (q - s->window)) :
+          q - c->sub.copy.dist;
+#else
+      f = q - c->sub.copy.dist;
+      if ((uInt)(q - s->window) < c->sub.copy.dist)
+        f = s->end - (c->sub.copy.dist - (q - s->window));
+#endif
+      while (c->len)
+      {
+        NEEDOUT
+        OUTBYTE(*f++)
+        if (f == s->end)
+          f = s->window;
+        c->len--;
+      }
+      c->mode = START;
+      break;
+    case LIT:           /* o: got literal, waiting for output space */
+      NEEDOUT
+      OUTBYTE(c->sub.lit)
+      c->mode = START;
+      break;
+    case WASH:          /* o: got eob, possibly more output */
+      FLUSH
+      if (s->read != s->write)
+        LEAVE
+      c->mode = END;
+    case END:
+      r = Z_STREAM_END;
+      LEAVE
+    case BADCODE:       /* x: got error */
+      r = Z_DATA_ERROR;
+      LEAVE
+    default:
+      r = Z_STREAM_ERROR;
+      LEAVE
+  }
+}
+
+
+local void inflate_codes_free(c, z)
+inflate_codes_statef *c;
+z_stream *z;
+{
+  ZFREE(z, c, sizeof(struct inflate_codes_state));
+  Tracev(( "inflate:       codes free\n"));
+}
+
+/*+++++*/
+/* inflate_util.c -- data and routines common to blocks and codes
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* copy as much as possible from the sliding window to the output area */
+local int inflate_flush(s, z, r)
+inflate_blocks_statef *s;
+z_stream *z;
+int r;
+{
+  uInt n;
+  Bytef *p, *q;
+
+  /* local copies of source and destination pointers */
+  p = z->next_out;
+  q = s->read;
+
+  /* compute number of bytes to copy as far as end of window */
+  n = (uInt)((q <= s->write ? s->write : s->end) - q);
+  if (n > z->avail_out) n = z->avail_out;
+  if (n && r == Z_BUF_ERROR) r = Z_OK;
+
+  /* update counters */
+  z->avail_out -= n;
+  z->total_out += n;
+
+  /* update check information */
+  if (s->checkfn != Z_NULL)
+    s->check = (*s->checkfn)(s->check, q, n);
+
+  /* copy as far as end of window */
+  zmemcpy(p, q, n);
+  p += n;
+  q += n;
+
+  /* see if more to copy at beginning of window */
+  if (q == s->end)
+  {
+    /* wrap pointers */
+    q = s->window;
+    if (s->write == s->end)
+      s->write = s->window;
+
+    /* compute bytes to copy */
+    n = (uInt)(s->write - q);
+    if (n > z->avail_out) n = z->avail_out;
+    if (n && r == Z_BUF_ERROR) r = Z_OK;
+
+    /* update counters */
+    z->avail_out -= n;
+    z->total_out += n;
+
+    /* update check information */
+    if (s->checkfn != Z_NULL)
+      s->check = (*s->checkfn)(s->check, q, n);
+
+    /* copy */
+    zmemcpy(p, q, n);
+    p += n;
+    q += n;
+  }
+
+  /* update pointers */
+  z->next_out = p;
+  s->read = q;
+
+  /* done */
+  return r;
+}
+
+
+/*+++++*/
+/* inffast.c -- process literals and length/distance pairs fast
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* simplify the use of the inflate_huft type with some defines */
+#define base more.Base
+#define next more.Next
+#define exop word.what.Exop
+#define bits word.what.Bits
+
+/* macros for bit input with no checking and for returning unused bytes */
+#define GRABBITS(j) {while(k<(j)){b|=((uLong)NEXTBYTE)<<k;k+=8;}}
+#define UNGRAB {n+=(c=k>>3);p-=c;k&=7;}
+
+/* Called with number of bytes left to write in window at least 258
+   (the maximum string length) and number of input bytes available
+   at least ten.  The ten bytes are six bytes for the longest length/
+   distance pair plus four bytes for overloading the bit buffer. */
+
+local int inflate_fast(bl, bd, tl, td, s, z)
+uInt bl, bd;
+inflate_huft *tl, *td;
+inflate_blocks_statef *s;
+z_stream *z;
+{
+  inflate_huft *t;      /* temporary pointer */
+  uInt e;               /* extra bits or operation */
+  uLong b;              /* bit buffer */
+  uInt k;               /* bits in bit buffer */
+  Bytef *p;             /* input data pointer */
+  uInt n;               /* bytes available there */
+  Bytef *q;             /* output window write pointer */
+  uInt m;               /* bytes to end of window or read pointer */
+  uInt ml;              /* mask for literal/length tree */
+  uInt md;              /* mask for distance tree */
+  uInt c;               /* bytes to copy */
+  uInt d;               /* distance back to copy from */
+  Bytef *r;             /* copy source pointer */
+
+  /* load input, output, bit values */
+  LOAD
+
+  /* initialize masks */
+  ml = inflate_mask[bl];
+  md = inflate_mask[bd];
+
+  /* do until not enough input or output space for fast loop */
+  do {                          /* assume called with m >= 258 && n >= 10 */
+    /* get literal/length code */
+    GRABBITS(20)                /* max bits for literal/length code */
+    if ((e = (t = tl + ((uInt)b & ml))->exop) == 0)
+    {
+      DUMPBITS(t->bits)
+      Tracevv(( t->base >= 0x20 && t->base < 0x7f ?
+                "inflate:         * literal '%c'\n" :
+                "inflate:         * literal 0x%02x\n", t->base));
+      *q++ = (Byte)t->base;
+      m--;
+      continue;
+    }
+    do {
+      DUMPBITS(t->bits)
+      if (e & 16)
+      {
+        /* get extra bits for length */
+        e &= 15;
+        c = t->base + ((uInt)b & inflate_mask[e]);
+        DUMPBITS(e)
+        Tracevv(( "inflate:         * length %u\n", c));
+
+        /* decode distance base of block to copy */
+        GRABBITS(15);           /* max bits for distance code */
+        e = (t = td + ((uInt)b & md))->exop;
+        do {
+          DUMPBITS(t->bits)
+          if (e & 16)
+          {
+            /* get extra bits to add to distance base */
+            e &= 15;
+            GRABBITS(e)         /* get extra bits (up to 13) */
+            d = t->base + ((uInt)b & inflate_mask[e]);
+            DUMPBITS(e)
+            Tracevv(( "inflate:         * distance %u\n", d));
+
+            /* do the copy */
+            m -= c;
+            if ((uInt)(q - s->window) >= d)     /* offset before dest */
+            {                                   /*  just copy */
+              r = q - d;
+              *q++ = *r++;  c--;        /* minimum count is three, */
+              *q++ = *r++;  c--;        /*  so unroll loop a little */
+            }
+            else                        /* else offset after destination */
+            {
+              e = d - (q - s->window);  /* bytes from offset to end */
+              r = s->end - e;           /* pointer to offset */
+              if (c > e)                /* if source crosses, */
+              {
+                c -= e;                 /* copy to end of window */
+                do {
+                  *q++ = *r++;
+                } while (--e);
+                r = s->window;          /* copy rest from start of window */
+              }
+            }
+            do {                        /* copy all or what's left */
+              *q++ = *r++;
+            } while (--c);
+            break;
+          }
+          else if ((e & 64) == 0)
+            e = (t = t->next + ((uInt)b & inflate_mask[e]))->exop;
+          else
+          {
+            z->msg = "invalid distance code";
+            UNGRAB
+            UPDATE
+            return Z_DATA_ERROR;
+          }
+        } while (1);
+        break;
+      }
+      if ((e & 64) == 0)
+      {
+        if ((e = (t = t->next + ((uInt)b & inflate_mask[e]))->exop) == 0)
+        {
+          DUMPBITS(t->bits)
+          Tracevv(( t->base >= 0x20 && t->base < 0x7f ?
+                    "inflate:         * literal '%c'\n" :
+                    "inflate:         * literal 0x%02x\n", t->base));
+          *q++ = (Byte)t->base;
+          m--;
+          break;
+        }
+      }
+      else if (e & 32)
+      {
+        Tracevv(( "inflate:         * end of block\n"));
+        UNGRAB
+        UPDATE
+        return Z_STREAM_END;
+      }
+      else
+      {
+        z->msg = "invalid literal/length code";
+        UNGRAB
+        UPDATE
+        return Z_DATA_ERROR;
+      }
+    } while (1);
+  } while (m >= 258 && n >= 10);
+
+  /* not enough input or output--restore pointers and return */
+  UNGRAB
+  UPDATE
+  return Z_OK;
+}
+
+
+/*+++++*/
+/* zutil.c -- target dependent utility functions for the compression library
+ * Copyright (C) 1995 Jean-loup Gailly.
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* From: zutil.c,v 1.8 1995/05/03 17:27:12 jloup Exp */
+
+char *zlib_version = ZLIB_VERSION;
+
+char *z_errmsg[] = {
+"stream end",          /* Z_STREAM_END    1 */
+"",                    /* Z_OK            0 */
+"file error",          /* Z_ERRNO        (-1) */
+"stream error",        /* Z_STREAM_ERROR (-2) */
+"data error",          /* Z_DATA_ERROR   (-3) */
+"insufficient memory", /* Z_MEM_ERROR    (-4) */
+"buffer error",        /* Z_BUF_ERROR    (-5) */
+""};
+
+
+/*+++++*/
+/* adler32.c -- compute the Adler-32 checksum of a data stream
+ * Copyright (C) 1995 Mark Adler
+ * For conditions of distribution and use, see copyright notice in zlib.h 
+ */
+
+/* From: adler32.c,v 1.6 1995/05/03 17:27:08 jloup Exp */
+
+#define BASE 65521L /* largest prime smaller than 65536 */
+#define NMAX 5552
+/* NMAX is the largest n such that 255n(n+1)/2 + (n+1)(BASE-1) <= 2^32-1 */
+
+#define DO1(buf)  {s1 += *buf++; s2 += s1;}
+#define DO2(buf)  DO1(buf); DO1(buf);
+#define DO4(buf)  DO2(buf); DO2(buf);
+#define DO8(buf)  DO4(buf); DO4(buf);
+#define DO16(buf) DO8(buf); DO8(buf);
+
+/* ========================================================================= */
+uLong adler32(adler, buf, len)
+    uLong adler;
+    Bytef *buf;
+    uInt len;
+{
+    unsigned long s1 = adler & 0xffff;
+    unsigned long s2 = (adler >> 16) & 0xffff;
+    int k;
+
+    if (buf == Z_NULL) return 1L;
+
+    while (len > 0) {
+        k = len < NMAX ? len : NMAX;
+        len -= k;
+        while (k >= 16) {
+            DO16(buf);
+            k -= 16;
+        }
+        if (k != 0) do {
+            DO1(buf);
+        } while (--k);
+        s1 %= BASE;
+        s2 %= BASE;
+    }
+    return (s2 << 16) | s1;
+}