Update from Eric Norum.

3 files changed, 366 insertions, 148 deletions

diff --git a/c/src/lib/libbsp/m68k/gen68360/startup/init68360.c b/c/src/lib/libbsp/m68k/gen68360/startup/init68360.c
index 5326cc0307..64cf94e6d4 100644
--- a/c/src/lib/libbsp/m68k/gen68360/startup/init68360.c
+++ b/c/src/lib/libbsp/m68k/gen68360/startup/init68360.c
@@ -32,14 +32,167 @@ void M360ExecuteRISC(rtems_unsigned16 command)
 /*
  * Initialize MC68360
  */
-
 void _Init68360 (void)
 {
 	int i;
-	unsigned long l;
 	m68k_isr_entry *vbr;
 	extern void _CopyDataClearBSSAndStart (void);
 
+#if (defined (m68040) || defined (m68lc040) || defined (m68ec040))
+	/*
+	 *******************************************
+	 * Motorola 68040 and companion-mode 68360 *
+	 *******************************************
+	 */
+
+	/*
+	 * Step 6: Is this a power-up reset?
+	 * For now we just ignore this and do *all* the steps
+	 * Someday we might want to:
+	 *	if (Hard, Loss of Clock, Power-up)
+	 *		Do all steps
+	 *	else if (Double bus fault, watchdog or soft reset)
+	 *		Skip to step 12
+	 *	else (must be a reset command)
+	 *		Skip to step 14
+	 */
+
+	/*
+	 * Step 7: Deal with clock synthesizer
+	 * HARDWARE:
+	 *	Change if you're not using an external 25 MHz oscillator.
+	 */
+	m360.clkocr = 0x83;	/* No more writes, full-power CLKO2 */
+	m360.pllcr = 0xD000;	/* PLL, no writes, no prescale,
+				   no LPSTOP slowdown, PLL X1 */
+	m360.cdvcr = 0x8000;	/* No more writes, no clock division */
+
+	/*
+	 * Step 8: Initialize system protection
+	 *	Disable watchdog FIXME: Should use watchdog!!!!
+	 *	Watchdog causes system reset
+	 *	Slowest watchdog timeout
+	 *	Disable double bus fault monitor
+	 *	Enable bus monitor external
+	 *	1024 clocks for external timeout
+	 */
+	m360.sypcr = 0x74;
+
+	/*
+	 * Step 9: Clear parameter RAM and reset communication processor module
+	 */
+	for (i = 0 ; i < 192  ; i += sizeof (long)) {
+		*((long *)((char *)&m360 + 0xC00 + i)) = 0;
+		*((long *)((char *)&m360 + 0xD00 + i)) = 0;
+		*((long *)((char *)&m360 + 0xE00 + i)) = 0;
+		*((long *)((char *)&m360 + 0xF00 + i)) = 0;
+	}
+	M360ExecuteRISC (M360_CR_RST);
+
+	/*
+	 * Step 10: Write PEPAR
+	 *	SINTOUT standard M68000 family interrupt level encoding
+	 *	CF1MODE=10 (BCLRO* output)
+	 *	No RAS1* double drive
+	 *	A31 - A28
+	 *	AMUX output
+	 *	CAS2* - CAS3*
+	 *	CAS0* - CAS1*
+	 *	CS7*
+	 *	AVEC*
+	 */
+	m360.pepar = 0x3440;
+
+	/*
+	 * Step 11: Remap Chip Select 0 (CS0*), set up GMR
+	 */
+	/*
+	 * 512 addresses per DRAM page (256K DRAM chips)
+	 * 70 nsec DRAM
+	 * 180 nsec ROM (3 wait states)
+	 */
+	m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
+				M360_GMR_RCYC(0) | M360_GMR_PGS(1) |
+				M360_GMR_DPS_32BIT | M360_GMR_NCS |
+				M360_GMR_TSS40;
+	m360.memc[0].br = (unsigned long)&_RomBase | M360_MEMC_BR_WP |
+							M360_MEMC_BR_V;
+	m360.memc[0].or = M360_MEMC_OR_WAITS(3) | M360_MEMC_OR_1MB |
+						M360_MEMC_OR_32BIT;
+
+	/*
+	 * Step 12: Initialize the system RAM
+	 */
+	/*
+	 *	Set up option/base registers
+	 *		1M DRAM
+	 *		70 nsec DRAM
+	 *	Enable burst mode
+	 *	No parity checking
+	 *	Wait for chips to power up
+	 *	Perform 8 read cycles
+	 */
+	m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
+					M360_MEMC_OR_1MB |
+					M360_MEMC_OR_DRAM;
+	m360.memc[1].br = (unsigned long)&_RamBase |
+					M360_MEMC_BR_BACK40 |
+					M360_MEMC_BR_V;
+	for (i = 0; i < 50000; i++)
+		continue;
+	for (i = 0; i < 8; ++i)
+		*((volatile unsigned long *)(unsigned long)&_RamBase);
+
+	/*
+	 * Step 13: Copy  the exception vector table to system RAM
+	 */
+	m68k_get_vbr (vbr);
+	for (i = 0; i < 256; ++i)
+		M68Kvec[i] = vbr[i];
+	m68k_set_vbr (M68Kvec);
+	
+	/*
+	 * Step 14: More system initialization
+	 * SDCR (Serial DMA configuration register)
+	 *	Disable SDMA during FREEZE
+	 *	Give SDMA priority over all interrupt handlers
+	 *	Set DMA arbiration level to 4
+	 * CICR (CPM interrupt configuration register):
+	 *	SCC1 requests at SCCa position
+	 *	SCC2 requests at SCCb position
+	 *	SCC3 requests at SCCc position
+	 *	SCC4 requests at SCCd position
+	 *	Interrupt request level 4
+	 *	Maintain original priority order
+	 *	Vector base 128
+	 *	SCCs priority grouped at top of table
+	 */
+	m360.sdcr = M360_SDMA_FREEZE | M360_SDMA_SISM_7 | M360_SDMA_SAID_4;
+	m360.cicr = (3 << 22) | (2 << 20) | (1 << 18) | (0 << 16) |
+						(4 << 13) | (0x1F << 8) | (128);
+
+	/*
+	 * Step 15: Set module configuration register
+	 *	Bus request MC68040 Arbitration ID 3
+	 *	Bus asynchronous timing mode (work around bug in Rev. B)
+	 *	Arbitration asynchronous timing mode
+	 *	Disable timers during FREEZE
+	 *	Disable bus monitor during FREEZE
+	 *	BCLRO* arbitration level 3
+	 *	No show cycles
+	 *	User/supervisor access
+	 *	Bus clear in arbitration ID level  3
+	 *	SIM60 interrupt sources higher priority than CPM
+	 */
+	m360.mcr = 0x6000EC3F;
+
+#elif (defined (M68360_ATLAS_HSB))
+	/*
+	 ******************************************
+	 * Standalone Motorola 68360 -- ATLAS HSB *
+	 ******************************************
+	 */
+
 	/*
 	 * Step 6: Is this a power-up reset?
 	 * For now we just ignore this and do *all* the steps
@@ -104,124 +257,234 @@ void _Init68360 (void)
 	/*
 	 * Step 11: Remap Chip Select 0 (CS0*), set up GMR
 	 */
-	if (&_MC68360HardwareType == &_MC68360HardwareTypeAtlasHSB) {
-		m360.gmr = M360_GMR_RCNT(12) | M360_GMR_RFEN | 
+	m360.gmr = M360_GMR_RCNT(12) | M360_GMR_RFEN | 
 				M360_GMR_RCYC(0) | M360_GMR_PGS(1) | 
 				M360_GMR_DPS_32BIT | M360_GMR_DWQ |
 				M360_GMR_GAMX;
-		m360.memc[0].br = (unsigned long)&_RomBase | M360_MEMC_BR_WP |
+	m360.memc[0].br = (unsigned long)&_RomBase | M360_MEMC_BR_WP |
 								M360_MEMC_BR_V;
-		m360.memc[0].or = M360_MEMC_OR_WAITS(3) | M360_MEMC_OR_1MB |
+	m360.memc[0].or = M360_MEMC_OR_WAITS(3) | M360_MEMC_OR_1MB |
 							M360_MEMC_OR_8BIT;
+
+	/*
+	 * Step 12: Initialize the system RAM
+	 */
+	/* first bank 1MByte DRAM */
+	m360.memc[1].or = M360_MEMC_OR_TCYC(2) | M360_MEMC_OR_1MB |
+					M360_MEMC_OR_PGME | M360_MEMC_OR_DRAM;
+	m360.memc[1].br = (unsigned long)&_RamBase | M360_MEMC_BR_V;
+
+	/* second bank 1MByte DRAM */
+	m360.memc[2].or = M360_MEMC_OR_TCYC(2) | M360_MEMC_OR_1MB |
+					M360_MEMC_OR_PGME | M360_MEMC_OR_DRAM;
+	m360.memc[2].br = ((unsigned long)&_RamBase + 0x100000) |
+					M360_MEMC_BR_V;
+
+	/* flash rom socket U6 on CS5 */
+	m360.memc[5].br = (unsigned long)ATLASHSB_ROM_U6 | M360_MEMC_BR_WP |
+								M360_MEMC_BR_V;
+	m360.memc[5].or = M360_MEMC_OR_WAITS(2) | M360_MEMC_OR_512KB |
+								M360_MEMC_OR_8BIT;
+
+	/* CSRs on CS7 */
+	m360.memc[7].or = M360_MEMC_OR_TCYC(4) | M360_MEMC_OR_64KB |
+					M360_MEMC_OR_8BIT;
+	m360.memc[7].br = ATLASHSB_ESR | 0x01;
+	for (i = 0; i < 50000; i++)
+		continue;
+	for (i = 0; i < 8; ++i)
+		*((volatile unsigned long *)(unsigned long)&_RamBase);
+
+	/*
+	 * Step 13: Copy  the exception vector table to system RAM
+	 */
+	m68k_get_vbr (vbr);
+	for (i = 0; i < 256; ++i)
+		M68Kvec[i] = vbr[i];
+	m68k_set_vbr (M68Kvec);
+	
+	/*
+	 * Step 14: More system initialization
+	 * SDCR (Serial DMA configuration register)
+	 *	Disable SDMA during FREEZE
+	 *	Give SDMA priority over all interrupt handlers
+	 *	Set DMA arbiration level to 4
+	 * CICR (CPM interrupt configuration register):
+	 *	SCC1 requests at SCCa position
+	 *	SCC2 requests at SCCb position
+	 *	SCC3 requests at SCCc position
+	 *	SCC4 requests at SCCd position
+	 *	Interrupt request level 4
+	 *	Maintain original priority order
+	 *	Vector base 128
+	 *	SCCs priority grouped at top of table
+	 */
+	m360.sdcr = M360_SDMA_FREEZE | M360_SDMA_SISM_7 | M360_SDMA_SAID_4;
+	m360.cicr = (3 << 22) | (2 << 20) | (1 << 18) | (0 << 16) |
+						(4 << 13) | (0x1F << 8) | (128);
+
+	/*
+	 * Step 15: Set module configuration register
+	 *	Disable timers during FREEZE
+	 *	Enable bus monitor during FREEZE
+	 *	BCLRO* arbitration level 3
+	 *	No show cycles
+	 *	User/supervisor access
+	 *	Bus clear interrupt service level 7
+	 *	SIM60 interrupt sources higher priority than CPM
+	 */
+	m360.mcr = 0x4C7F;
+
+#else
+	/*
+	 ***************************************************
+	 * Generic Standalone Motorola 68360               *
+	 *           As described in MC68360 User's Manual *
+	 *           Atlas ACE360                          *
+	 ***************************************************
+	 */
+
+	/*
+	 * Step 6: Is this a power-up reset?
+	 * For now we just ignore this and do *all* the steps
+	 * Someday we might want to:
+	 *	if (Hard, Loss of Clock, Power-up)
+	 *		Do all steps
+	 *	else if (Double bus fault, watchdog or soft reset)
+	 *		Skip to step 12
+	 *	else (must be a CPU32+ reset command)
+	 *		Skip to step 14
+	 */
+
+	/*
+	 * Step 7: Deal with clock synthesizer
+	 * HARDWARE:
+	 *	Change if you're not using an external 25 MHz oscillator.
+	 */
+	m360.clkocr = 0x8F;	/* No more writes, no clock outputs */
+	m360.pllcr = 0xD000;	/* PLL, no writes, no prescale,
+				   no LPSTOP slowdown, PLL X1 */
+	m360.cdvcr = 0x8000;	/* No more writes, no clock division */
+
+	/*
+	 * Step 8: Initialize system protection
+	 *	Disable watchdog FIXME: Should use watchdog!!!!
+	 *	Watchdog causes system reset
+	 *	Slowest watchdog timeout
+	 *	Enable double bus fault monitor
+	 *	Enable bus monitor external
+	 *	128 clocks for external timeout
+	 */
+	m360.sypcr = 0x7F;
+
+	/*
+	 * Step 9: Clear parameter RAM and reset communication processor module
+	 */
+	for (i = 0 ; i < 192  ; i += sizeof (long)) {
+		*((long *)((char *)&m360 + 0xC00 + i)) = 0;
+		*((long *)((char *)&m360 + 0xD00 + i)) = 0;
+		*((long *)((char *)&m360 + 0xE00 + i)) = 0;
+		*((long *)((char *)&m360 + 0xF00 + i)) = 0;
 	}
-	else {
-		/*
-		 * 1024/2048/4096 addresses per DRAM page (1M/4M/16M DRAM chips)
-		 * 60 nsec DRAM
-		 * 180 nsec ROM (3 wait states)
-		 */
-		switch ((unsigned long)&_RamSize) {
-		default:
-		case 4*1024*1024:
-			m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
+	M360ExecuteRISC (M360_CR_RST);
+
+	/*
+	 * Step 10: Write PEPAR
+	 *	SINTOUT not used (CPU32+ mode)
+	 *	CF1MODE=00 (CONFIG1 input)
+	 *	RAS1* double drive
+	 *	WE0* - WE3*
+	 *	OE* output
+	 *	CAS2* - CAS3*
+	 *	CAS0* - CAS1*
+	 *	CS7*
+	 *	AVEC*
+	 * HARDWARE:
+	 *	Change if you are using a different memory configuration
+	 *	(static RAM, external address multiplexing, etc).
+	 */
+	m360.pepar = 0x0180;
+
+	/*
+	 * Step 11: Remap Chip Select 0 (CS0*), set up GMR
+	 */
+	/*
+	 * 1024/2048/4096 addresses per DRAM page (1M/4M/16M DRAM chips)
+	 * 60 nsec DRAM
+	 * 180 nsec ROM (3 wait states)
+	 */
+	switch ((unsigned long)&_RamSize) {
+	default:
+	case 4*1024*1024:
+		m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
 					M360_GMR_RCYC(0) | M360_GMR_PGS(3) |
 					M360_GMR_DPS_32BIT | M360_GMR_NCS | 
 					M360_GMR_GAMX;
-			break;
+		break;
 
-		case 16*1024*1024:
-			m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
+	case 16*1024*1024:
+		m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
 					M360_GMR_RCYC(0) | M360_GMR_PGS(5) |
 					M360_GMR_DPS_32BIT | M360_GMR_NCS | 
 					M360_GMR_GAMX;
-			break;
+		break;
 
-		case 64*1024*1024:
-			m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
+	case 64*1024*1024:
+		m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | 
 					M360_GMR_RCYC(0) | M360_GMR_PGS(7) |
 					M360_GMR_DPS_32BIT | M360_GMR_NCS | 
 					M360_GMR_GAMX;
-			break;
-		}
-		m360.memc[0].br = (unsigned long)&_RomBase | M360_MEMC_BR_WP |
+		break;
+	}
+	m360.memc[0].br = (unsigned long)&_RomBase | M360_MEMC_BR_WP |
 								M360_MEMC_BR_V;
-		m360.memc[0].or = M360_MEMC_OR_WAITS(3) | M360_MEMC_OR_1MB |
+	m360.memc[0].or = M360_MEMC_OR_WAITS(3) | M360_MEMC_OR_1MB |
 							M360_MEMC_OR_8BIT;
-	}
 
 	/*
 	 * Step 12: Initialize the system RAM
 	 */
-	if (&_MC68360HardwareType == &_MC68360HardwareTypeAtlasHSB) {
-		/* first bank 1MByte DRAM */
-		m360.memc[1].or = M360_MEMC_OR_TCYC(2) | M360_MEMC_OR_1MB |
-					M360_MEMC_OR_PGME | M360_MEMC_OR_DRAM;
-		m360.memc[1].br = (unsigned long)&_RamBase | M360_MEMC_BR_V;
-
-		/* second bank 1MByte DRAM */
-		m360.memc[2].or = M360_MEMC_OR_TCYC(2) | M360_MEMC_OR_1MB |
-					M360_MEMC_OR_PGME | M360_MEMC_OR_DRAM;
-		m360.memc[2].br = ((unsigned long)&_RamBase + 0x100000) |
-					M360_MEMC_BR_V;
+	/*
+	 *	Set up option/base registers
+	 *		4M/16M/64M DRAM
+	 *		60 nsec DRAM
+	 *	Wait for chips to power up
+	 *	Perform 8 read cycles
+	 *	Set all parity bits to correct state
+	 *	Enable parity checking
+	 */
+	switch ((unsigned long)&_RamSize) {
+	default:
+	case 4*1024*1024:
+		m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
+					M360_MEMC_OR_4MB |
+					M360_MEMC_OR_DRAM;
+		break;
 
-		/* flash rom socket U6 on CS5 */
-		m360.memc[5].br = (unsigned long)ATLASHSB_ROM_U6 | M360_MEMC_BR_WP |
-								M360_MEMC_BR_V;
-		m360.memc[5].or = M360_MEMC_OR_WAITS(2) | M360_MEMC_OR_512KB |
-								M360_MEMC_OR_8BIT;
+	case 16*1024*1024:
+		m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
+					M360_MEMC_OR_16MB |
+					M360_MEMC_OR_DRAM;
+		break;
 
-		/* CSRs on CS7 */
-		m360.memc[7].or = M360_MEMC_OR_TCYC(4) | M360_MEMC_OR_64KB |
-					M360_MEMC_OR_8BIT;
-		m360.memc[7].br = ATLASHSB_ESR | 0x01;
-		for (i = 0; i < 50000; i++)
-			continue;
-		for (i = 0; i < 8; ++i)
-			*((volatile unsigned long *)(unsigned long)&_RamBase);
+	case 64*1024*1024:
+		m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
+					M360_MEMC_OR_64MB |
+					M360_MEMC_OR_DRAM;
+		break;
 	}
-	else {
-		/*
-		 *	Set up option/base registers
-		 *		4M/16M/64M DRAM
-		 *		60 nsec DRAM
-		 *	Wait for chips to power up
-		 *	Perform 8 read cycles
-		 *	Set all parity bits to correct state
-		 *	Enable parity checking
-		 */
-		switch ((unsigned long)&_RamSize) {
-		default:
-		case 4*1024*1024:
-			m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
-						M360_MEMC_OR_4MB |
-						M360_MEMC_OR_DRAM;
-			break;
-
-		case 16*1024*1024:
-			m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
-						M360_MEMC_OR_16MB |
-						M360_MEMC_OR_DRAM;
-			break;
-
-		case 64*1024*1024:
-			m360.memc[1].or = M360_MEMC_OR_TCYC(0) |
-						M360_MEMC_OR_64MB |
-						M360_MEMC_OR_DRAM;
-			break;
-		}
-		m360.memc[1].br = (unsigned long)&_RamBase | M360_MEMC_BR_V;
-		for (i = 0; i < 50000; i++)
-			continue;
-		for (i = 0; i < 8; ++i)
-			*((volatile unsigned long *)(unsigned long)&_RamBase);
-		for (l = 0 ; l < (unsigned long)&_RamSize ; l += sizeof (unsigned long)) {
-			volatile unsigned long *lp;
-			lp = (unsigned long *)((unsigned char *)&_RamBase + i);
-			*lp = *lp;
-		}
-		m360.memc[1].br = (unsigned long)&_RamBase |
-					M360_MEMC_BR_PAREN | M360_MEMC_BR_V;
+	m360.memc[1].br = (unsigned long)&_RamBase | M360_MEMC_BR_V;
+	for (i = 0; i < 50000; i++)
+		continue;
+	for (i = 0; i < 8; ++i)
+		*((volatile unsigned long *)(unsigned long)&_RamBase);
+	for (i = 0 ; i < (unsigned long)&_RamSize ; i += sizeof (unsigned long)) {
+		volatile unsigned long *lp;
+		lp = (unsigned long *)((unsigned char *)&_RamBase + i);
+		*lp = *lp;
 	}
+	m360.memc[1].br = (unsigned long)&_RamBase |
+				M360_MEMC_BR_PAREN | M360_MEMC_BR_V;
 
 	/*
 	 * Step 13: Copy  the exception vector table to system RAM
@@ -262,6 +525,7 @@ void _Init68360 (void)
 	 *	SIM60 interrupt sources higher priority than CPM
 	 */
 	m360.mcr = 0x4C7F;
+#endif
 
 	/*
 	 * Copy data, clear BSS, switch stacks and call main()
diff --git a/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds b/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds
index 6a2d950853..b50954e10c 100644
--- a/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds
+++ b/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds
@@ -1,7 +1,7 @@
 /*
  * This file contains GNU linker directives for a generic MC68360 board.
- * Variations in hardware type and dynamic memory size can be made
- * by overriding some values with linker command-line arguments.
+ * Variations in memory size and allocation can be made by
+ * overriding some values with linker command-line arguments.
  *
  * Saskatchewan Accelerator Laboratory
  * University of Saskatchewan
@@ -22,13 +22,6 @@ HeapSize = DEFINED(HeapSize) ? HeapSize : 0x10000;
 StackSize = DEFINED(StackSize) ? StackSize : 0x1000;
 
 /*
- * Declare hardware type
- */
-MC68360HardwareTypeMotorolaGeneric = 0; 
-MC68360HardwareTypeAtlasHSB = 1; 
-MC68360HardwareType = DEFINED(MC68360HardwareType) ? MC68360HardwareType : 0;
-
-/*
  * Declare on-board memory.
  * It would be nice if the ram length could be given as
  * LENGTH=RamSize, but gld doesn't allow non-constant
@@ -36,8 +29,8 @@ MC68360HardwareType = DEFINED(MC68360HardwareType) ? MC68360HardwareType : 0;
  */
 MEMORY {
           ram : ORIGIN = 0x00000000, LENGTH = 64M
-          rom : ORIGIN = 0xFF000000, LENGTH = 1M
-        dpram : ORIGIN = 0xFE000000, LENGTH = 8k
+          rom : ORIGIN = 0x0F000000, LENGTH = 1M
+        dpram : ORIGIN = 0x0E000000, LENGTH = 8k
 }
 
 /*
@@ -46,15 +39,6 @@ MEMORY {
 ETHERNET_ADDRESS = DEFINED(ETHERNET_ADDRESS) ? ETHERNET_ADDRESS : 0xDEAD12;
 
 /*
- * Declare hardware type.
- * Acceptable values are:
- *	0 - Generic system as described in the MC68360 User's Manual
- *	    (MC68360UM/AD Rev. 1).
- *	1 - ATLAS Computer Equipment Incorporated ACE360/HSB.
- */
-MC68360HardwareType = DEFINED(MC68360HardwareType) ? MC68360HardwareType : 0;
-
-/*
  * Load objects
  */
 SECTIONS {
@@ -63,12 +47,6 @@ SECTIONS {
 	 */
 	_RamSize = RamSize;
 	__RamSize = RamSize;
-	_MC68360HardwareType = MC68360HardwareType;
-	__MC68360HardwareType = MC68360HardwareType;
-	_MC68360HardwareTypeMotorolaGeneric = MC68360HardwareTypeMotorolaGeneric; 
-	__MC68360HardwareTypeMotorolaGeneric = MC68360HardwareTypeMotorolaGeneric; 
-	_MC68360HardwareTypeAtlasHSB = MC68360HardwareTypeAtlasHSB; 
-	__MC68360HardwareTypeAtlasHSB = MC68360HardwareTypeAtlasHSB; 
 
         /*
          * Boot PROM
diff --git a/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds.bootp b/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds.bootp
index 0fb1008376..a39b355e25 100644
--- a/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds.bootp
+++ b/c/src/lib/libbsp/m68k/gen68360/startup/linkcmds.bootp
@@ -4,16 +4,14 @@
  * by overriding some values with linker command-line arguments.
  *
  * These linker directives are for producing a PROM version.
- * To create the PROM image from the linker output you must use objcopy
- * (--adjust-section-vma) to place the data segment at the end of the text
- * segment in the PROM.  The start-up code takes care of copying this region
- * to RAM.
+ * The data segment is placed at the end of the text segment in the PROM.
+ * The start-up code takes care of copying this region to RAM.
  *
  * Saskatchewan Accelerator Laboratory
  * University of Saskatchewan
  * Saskatoon, Saskatchewan, CANADA
  * eric@skatter.usask.ca
- * 
+ *
  *  $Id$
  */
 
@@ -28,13 +26,6 @@ HeapSize = DEFINED(HeapSize) ? HeapSize : 0x10000;
 StackSize = DEFINED(StackSize) ? StackSize : 0x1000;
 
 /*
- * Declare hardware type
- */
-MC68360HardwareTypeMotorolaGeneric = 0; 
-MC68360HardwareTypeAtlasHSB = 1; 
-MC68360HardwareType = DEFINED(MC68360HardwareType) ? MC68360HardwareType : 0;
-
-/*
  * Declare on-board memory.
  * It would be nice if the ram length could be given as
  * LENGTH=RamSize, but gld doesn't allow non-constant
@@ -43,8 +34,8 @@ MC68360HardwareType = DEFINED(MC68360HardwareType) ? MC68360HardwareType : 0;
 MEMORY {
           ram : ORIGIN = 0x00000000, LENGTH = 64M
         myram : ORIGIN = 4M-512k,    LENGTH = 512k
-          rom : ORIGIN = 0xFF000000, LENGTH = 1M
-        dpram : ORIGIN = 0xFE000000, LENGTH = 8k
+          rom : ORIGIN = 0x0F000000, LENGTH = 1M
+        dpram : ORIGIN = 0x0E000000, LENGTH = 8k
 }
 
 /*
@@ -53,15 +44,6 @@ MEMORY {
 ETHERNET_ADDRESS = DEFINED(ETHERNET_ADDRESS) ? ETHERNET_ADDRESS : 0xDEAD12;
 
 /*
- * Declare hardware type.
- * Acceptable values are:
- *	0 - Generic system as described in the MC68360 User's Manual
- *	    (MC68360UM/AD Rev. 1).
- *	1 - ATLAS Computer Equipment Incorporated ACE360/HSB.
- */
-MC68360HardwareType = DEFINED(MC68360HardwareType) ? MC68360HardwareType : 0;
-
-/*
  * Load objects
  */
 SECTIONS {
@@ -70,12 +52,6 @@ SECTIONS {
 	 */
 	_RamSize = RamSize;
 	__RamSize = RamSize;
-	_MC68360HardwareType = MC68360HardwareType;
-	__MC68360HardwareType = MC68360HardwareType;
-	_MC68360HardwareTypeMotorolaGeneric = MC68360HardwareTypeMotorolaGeneric; 
-	__MC68360HardwareTypeMotorolaGeneric = MC68360HardwareTypeMotorolaGeneric; 
-	_MC68360HardwareTypeAtlasHSB = MC68360HardwareTypeAtlasHSB; 
-	__MC68360HardwareTypeAtlasHSB = MC68360HardwareTypeAtlasHSB; 
 
         /*
          * Boot PROM