blob: 0324e2700e73574dd34380f1772ef8d056d555c6 (
plain) (
tree)
|
|
@c
@c COPYRIGHT (c) 1988-2008.
@c On-Line Applications Research Corporation (OAR).
@c All rights reserved.
@c
@c $Id$
@c
@chapter Network Commands
@section Introduction
The RTEMS shell has the following network commands:
@itemize @bullet
@item @code{netstats} - obtain network statistics
@item @code{ifconfig} - configure a network interface
@item @code{route} - show or manipulate the IP routing table
@end itemize
@section Commands
This section details the Network Commands available. A
subsection is dedicated to each of the commands and
describes the behavior and configuration of that
command as well as providing an example usage.
@c
@c
@c
@page
@subsection netstats - obtain network statistics
@pgindex netstats
@subheading SYNOPSYS:
@example
netstats [-Aimfpcut]
@end example
@subheading DESCRIPTION:
This command is used to display various types of network statistics. The
information displayed can be specified using command line arguments in
various combinations. The arguments are interpreted as follows:
@table @b
@item -A
print All statistics
@item -i
print Inet Routes
@item -m
print MBUF Statistics
@item -f
print IF Statistics
@item -p
print IP Statistics
@item -c
print ICMP Statistics
@item -u
print UDP Statistics
@item -t
print TCP Statistics
@end table
@subheading EXIT STATUS:
This command returns 0 on success and non-zero if an error is encountered.
@subheading NOTES:
NONE
@subheading EXAMPLES:
The following is an example of how to use @code{netstats}:
The following is an example of using the @code{netstats}
command to print the IP routing table:
@smallexample
[/] $ netstats -i
Destination Gateway/Mask/Hw Flags Refs Use Expire Interface
default 192.168.1.14 UGS 0 0 0 eth1
192.168.1.0 255.255.255.0 U 0 0 1 eth1
192.168.1.14 00:A0:C8:1C:EE:28 UHL 1 0 1219 eth1
192.168.1.51 00:1D:7E:0C:D0:7C UHL 0 840 1202 eth1
192.168.1.151 00:1C:23:B2:0F:BB UHL 1 23 1219 eth1
@end smallexample
The following is an example of using the @code{netstats}
command to print the MBUF statistics:
@smallexample
[/] $ netstats -m
************ MBUF STATISTICS ************
mbufs:2048 clusters: 128 free: 63
drops: 0 waits: 0 drains: 0
free:1967 data:79 header:2 socket:0
pcb:0 rtable:0 htable:0 atable:0
soname:0 soopts:0 ftable:0 rights:0
ifaddr:0 control:0 oobdata:0
@end smallexample
The following is an example of using the @code{netstats}
command to print the print the interface statistics:
@smallexample
[/] $ netstats -f
************ INTERFACE STATISTICS ************
***** eth1 *****
Ethernet Address: 00:04:9F:00:5B:21
Address:192.168.1.244 Broadcast Address:192.168.1.255 Net mask:255.255.255.0
Flags: Up Broadcast Running Active Multicast
Send queue limit:50 length:1 Dropped:0
Rx Interrupts:889 Not First:0 Not Last:0
Giant:0 Non-octet:0
Bad CRC:0 Overrun:0 Collision:0
Tx Interrupts:867 Deferred:0 Late Collision:0
Retransmit Limit:0 Underrun:0 Misaligned:0
@end smallexample
The following is an example of using the @code{netstats}
command to print the print IP statistics:
@smallexample
[/] $ netstats -p
************ IP Statistics ************
total packets received 894
packets rcvd for unreachable dest 13
datagrams delivered to upper level 881
total ip packets generated here 871
@end smallexample
The following is an example of using the @code{netstats}
command to print the ICMP statistics:
@smallexample
[/] $ netstats -c
************ ICMP Statistics ************
Type 0 sent 843
number of responses 843
Type 8 received 843
@end smallexample
The following is an example of using the @code{netstats}
command to print the UDP statistics:
@smallexample
[/] $ netstats -u
************ UDP Statistics ************
@end smallexample
The following is an example of using the @code{netstats}
command to print the TCP statistics:
@smallexample
[/] $ netstats -t
************ TCP Statistics ************
connections accepted 1
connections established 1
segs where we tried to get rtt 34
times we succeeded 35
delayed acks sent 2
total packets sent 37
data packets sent 35
data bytes sent 2618
ack-only packets sent 2
total packets received 47
packets received in sequence 12
bytes received in sequence 307
rcvd ack packets 35
bytes acked by rcvd acks 2590
times hdr predict ok for acks 27
times hdr predict ok for data pkts 10
@end smallexample
@subheading CONFIGURATION:
@findex CONFIGURE_SHELL_NO_COMMAND_NETSTATS
@findex CONFIGURE_SHELL_COMMAND_NETSTATS
This command is included in the default shell command set.
When building a custom command set, define
@code{CONFIGURE_SHELL_COMMAND_NETSTATS} to have this
command included.
This command can be excluded from the shell command set by
defining @code{CONFIGURE_SHELL_NO_COMMAND_NETSTATS} when all
shell commands have been configured.
@subheading PROGRAMMING INFORMATION:
@findex rtems_shell_rtems_main_netstats
The @code{netstats} is implemented by a C language function
which has the following prototype:
@example
int rtems_shell_rtems_main_netstats(
int argc,
char **argv
);
@end example
The configuration structure for the @code{netstats} has the
following prototype:
@example
extern rtems_shell_cmd_t rtems_shell_NETSTATS_Command;
@end example
@c
@c
@c
@page
@subsection ifconfig - configure a network interface
@pgindex ifconfig
@subheading SYNOPSYS:
@example
ifconfig
ifconfig interface
ifconfig interface [up|down]
ifconfig interface [netmask|pointtopoint|broadcast] IP
@end example
@subheading DESCRIPTION:
This command may be used to display information about the
network interfaces in the system or configure them.
@subheading EXIT STATUS:
This command returns 0 on success and non-zero if an error is encountered.
@subheading NOTES:
Just like its counterpart on GNU/Linux and BSD systems, this command
is complicated. More example usages would be a welcome submission.
@subheading EXAMPLES:
The following is an example of how to use @code{ifconfig}:
@smallexample
************ INTERFACE STATISTICS ************
***** eth1 *****
Ethernet Address: 00:04:9F:00:5B:21
Address:192.168.1.244 Broadcast Address:192.168.1.255 Net mask:255.255.255.0
Flags: Up Broadcast Running Active Multicast
Send queue limit:50 length:1 Dropped:0
Rx Interrupts:5391 Not First:0 Not Last:0
Giant:0 Non-octet:0
Bad CRC:0 Overrun:0 Collision:0
Tx Interrupts:5256 Deferred:0 Late Collision:0
Retransmit Limit:0 Underrun:0 Misaligned:0
@end smallexample
@subheading CONFIGURATION:
@findex CONFIGURE_SHELL_NO_COMMAND_IFCONFIG
@findex CONFIGURE_SHELL_COMMAND_IFCONFIG
This command is included in the default shell command set.
When building a custom command set, define
@code{CONFIGURE_SHELL_COMMAND_IFCONFIG} to have this
command included.
This command can be excluded from the shell command set by
defining @code{CONFIGURE_SHELL_NO_COMMAND_IFCONFIG} when all
shell commands have been configured.
@subheading PROGRAMMING INFORMATION:
@findex rtems_shell_rtems_main_ifconfig
The @code{ifconfig} is implemented by a C language function
which has the following prototype:
@example
int rtems_shell_rtems_main_ifconfig(
int argc,
char **argv
);
@end example
The configuration structure for the @code{ifconfig} has the
following prototype:
@example
extern rtems_shell_cmd_t rtems_shell_IFCONFIG_Command;
@end example
@c
@c
@c
@page
@subsection route - show or manipulate the ip routing table
@pgindex route
@subheading SYNOPSYS:
@example
route [subcommand] [args]
@end example
@subheading DESCRIPTION:
This command is used to display and manipulate the routing table.
When invoked with no arguments, the current routing information is
displayed. When invoked with the subcommands @code{add} or @code{del},
then additional arguments must be provided to describe the route.
Command templates include the following:
@smallexample
route [add|del] -net IP_ADDRESS gw GATEWAY_ADDRESS [netmask MASK]
route [add|del] -host IP_ADDRESS gw GATEWAY_ADDRES [netmask MASK]
@end smallexample
When not provided the netmask defaults to @code{255.255.255.0}
@subheading EXIT STATUS:
This command returns 0 on success and non-zero if an error is encountered.
@subheading NOTES:
Just like its counterpart on GNU/Linux and BSD systems, this command
is complicated. More example usages would be a welcome submission.
@subheading EXAMPLES:
The following is an example of how to use @code{route} to display,
add, and delete a new route:
@smallexample
[/] $ route
Destination Gateway/Mask/Hw Flags Refs Use Expire Interface
default 192.168.1.14 UGS 0 0 0 eth1
192.168.1.0 255.255.255.0 U 0 0 1 eth1
192.168.1.14 00:A0:C8:1C:EE:28 UHL 1 0 1444 eth1
192.168.1.51 00:1D:7E:0C:D0:7C UHL 0 10844 1202 eth1
192.168.1.151 00:1C:23:B2:0F:BB UHL 2 37 1399 eth1
[/] $ route add -net 192.168.3.0 gw 192.168.1.14
[/] $ route
Destination Gateway/Mask/Hw Flags Refs Use Expire Interface
default 192.168.1.14 UGS 0 0 0 eth1
192.168.1.0 255.255.255.0 U 0 0 1 eth1
192.168.1.14 00:A0:C8:1C:EE:28 UHL 2 0 1498 eth1
192.168.1.51 00:1D:7E:0C:D0:7C UHL 0 14937 1202 eth1
192.168.1.151 00:1C:23:B2:0F:BB UHL 2 96 1399 eth1
192.168.3.0 192.168.1.14 UGS 0 0 0 eth1
[/] $ route del -net 192.168.3.0 gw 192.168.1.14
[/] $ route
Destination Gateway/Mask/Hw Flags Refs Use Expire Interface
default 192.168.1.14 UGS 0 0 0 eth1
192.168.1.0 255.255.255.0 U 0 0 1 eth1
192.168.1.14 00:A0:C8:1C:EE:28 UHL 1 0 1498 eth1
192.168.1.51 00:1D:7E:0C:D0:7C UHL 0 15945 1202 eth1
192.168.1.151 00:1C:23:B2:0F:BB UHL 2 117 1399 eth1
@end smallexample
@subheading CONFIGURATION:
@findex CONFIGURE_SHELL_NO_COMMAND_ROUTE
@findex CONFIGURE_SHELL_COMMAND_ROUTE
This command is included in the default shell command set.
When building a custom command set, define
@code{CONFIGURE_SHELL_COMMAND_ROUTE} to have this
command included.
This command can be excluded from the shell command set by
defining @code{CONFIGURE_SHELL_NO_COMMAND_ROUTE} when all
shell commands have been configured.
@subheading PROGRAMMING INFORMATION:
@findex rtems_shell_rtems_main_route
The @code{route} is implemented by a C language function
which has the following prototype:
@example
int rtems_shell_rtems_main_route(
int argc,
char **argv
);
@end example
The configuration structure for the @code{route} has the
following prototype:
@example
extern rtems_shell_cmd_t rtems_shell_ROUTE_Command;
@end example
|