## Process this file with autoconf to produce a configure script.
##
## $Id$
AC_PREREQ(2.59)
AC_INIT([rtems-c-src-lib-libbsp-powerpc-mpc8260ads],[_RTEMS_VERSION],[rtems-bugs@rtems.com])
AC_CONFIG_SRCDIR([bsp_specs])
RTEMS_TOP(../../../../../..)
RTEMS_CANONICAL_TARGET_CPU
AM_INIT_AUTOMAKE([no-define nostdinc foreign 1.9])
RTEMS_BSP_CONFIGURE
RTEMS_PROG_CC_FOR_TARGET([-ansi -fasm])
RTEMS_CANONICALIZE_TOOLS
RTEMS_PROG_CCAS
RTEMS_BSPOPTS_SET([DATA_CACHE_ENABLE],[*],[0])
RTEMS_BSPOPTS_HELP([DATA_CACHE_ENABLE],
[If defined, the data cache will be enabled after address translation
is turned on.])
RTEMS_BSPOPTS_SET([INSTRUCTION_CACHE_ENABLE],[*],[0])
RTEMS_BSPOPTS_HELP([INSTRUCTION_CACHE_ENABLE],
[If defined, the instruction cache will be enabled after address translation
is turned on.])
RTEMS_BSPOPTS_SET([UARTS_USE_TERMIOS],[*],[0])
RTEMS_BSPOPTS_HELP([UARTS_USE_TERMIOS],
[Define to 1 if you want termios support for every port.
Termios support is independent of the choice of UART I/O mode.])
RTEMS_BSPOPTS_SET([CONSOLE_MINOR],[*],[SCC2_MINOR])
RTEMS_BSPOPTS_HELP([CONSOLE_MINOR],
[(BSP--console driver) Must be defined to be one of SMC1_MINOR,
SMC2_MINOR, SCC2_MINOR, SCC3_MINOR, or SCC4_MINOR.
Determines which device will be registered as /dev/console.])
RTEMS_BSPOPTS_SET([UARTS_IO_MODE],[*],[0])
RTEMS_BSPOPTS_HELP([UARTS_IO_MODE],
[(BSP--console driver)
Define to 0 or 1 if you want polled I/O performed by RTEMS.
Define to 1 if you want interrupt-driven performed by RTEMS.
Define to 2 if you want polled I/O performed by EPPCBug.
There is no provision to have a mix of interrupt-driven and polled I/O
ports, except that the printk port may use a different mode from the
other ports. If this is done, do not open the printk port from an RTEMS
application. With EPPCBug 1.1, if mode 2 is selected, CONSOLE_MINOR
must be set to SMC1_MINOR. This is a deficiency of the firmware: it
does not perform serial I/O on any port other than its default debug
port, which must be SMC1.])
RTEMS_BSPOPTS_SET([PRINTK_MINOR],[*],[SMC2_MINOR])
RTEMS_BSPOPTS_HELP([PRINTK_MINOR],
[(BSP--console driver)
Must be defined to be one of SMC1_MINOR, SMC2_MINOR, SCC2_MINOR,
SCC3_MINOR, or SCC4_MINOR. Determines which device is used for output
by printk(). If the port that printk() uses is also used for other
I/O (e.g. if PRINTK_MINOR == \$CONSOLE_MINOR), then both ports should
use the same type of I/O, otherwise the drivers will likely conflict with
each other.])
RTEMS_BSPOPTS_SET([DISPATCH_HANDLER_STAT],[*],[])
RTEMS_BSPOPTS_HELP([DISPATCH_HANDLER_STAT],
[used by irq/irq.c])
RTEMS_CHECK_NETWORKING
AM_CONDITIONAL(HAS_NETWORKING,test "$HAS_NETWORKING" = "yes")
# Explicitly list a Makefile here
AC_CONFIG_FILES([Makefile
wrapup/Makefile])
RTEMS_PPC_EXCEPTIONS([new])
AC_OUTPUT