/*
* This routine starts the application. It includes application,
* board, and monitor specific initialization and configuration.
* The generic CPU dependent initialization has been performed
* before this routine is invoked.
*
* COPYRIGHT (c) 1989-2001.
* On-Line Applications Research Corporation (OAR).
*
* The license and distribution terms for this file may be
* found in the file LICENSE in this distribution or at
* http://www.rtems.com/license/LICENSE.
*
* $Id$
*
* Modification History:
* 12/10/01 A.Ferrer, NASA/GSFC, Code 582
* Set interrupt mask to 0xAF00 (Line 139).
*/
#include <string.h>
#include <bsp.h>
#include <rtems/libio.h>
#include <rtems/libcsupport.h>
#include <libcpu/mongoose-v.h>
/*
* Use the shared implementations of the following routines
*/
void bsp_libc_init( void *, uint32_t, int );
/*
* Function: bsp_pretasking_hook
* Created: 95/03/10
*
* Description:
* BSP pretasking hook. Called just before drivers are initialized.
* Used to setup libc and install any BSP extensions.
*
* NOTES:
* Must not use libc (to do io) from here, since drivers are
* not yet initialized.
*
*/
void bsp_pretasking_hook(void)
{
extern int HeapBase;
extern int HeapSize;
void *heapStart = &HeapBase;
unsigned long heapSize = (unsigned long)&HeapSize;
bsp_libc_init(heapStart, (uint32_t) heapSize, 0);
}
/*
* bsp_start
*
* This routine does the bulk of the system initialization.
*/
void bsp_start( void )
{
extern void _sys_exit(int);
extern int WorkspaceBase;
extern void mips_install_isr_entries();
extern void mips_gdb_stub_install(void);
/* HACK -- tied to value linkcmds */
if ( rtems_configuration_get_work_space_size() > (4096*1024) )
_sys_exit( 1 );
Configuration.work_space_start = (void *) &WorkspaceBase;
/* mask off any interrupts */
MONGOOSEV_WRITE( MONGOOSEV_PERIPHERAL_FUNCTION_INTERRUPT_MASK_REGISTER, 0 );
/* reset the config register & clear any pending peripheral interrupts */
MONGOOSEV_WRITE( MONGOOSEV_PERIPHERAL_COMMAND_REGISTER, 0 );
MONGOOSEV_WRITE( MONGOOSEV_PERIPHERAL_COMMAND_REGISTER, MONGOOSEV_UART_CMD_RESET_BOTH_PORTS );
MONGOOSEV_WRITE( MONGOOSEV_PERIPHERAL_COMMAND_REGISTER, 0 );
/* reset both timers */
MONGOOSEV_WRITE_REGISTER( MONGOOSEV_TIMER1_BASE, MONGOOSEV_TIMER_INITIAL_COUNTER_REGISTER, 0xffffffff );
MONGOOSEV_WRITE_REGISTER( MONGOOSEV_TIMER1_BASE, MONGOOSEV_TIMER_CONTROL_REGISTER, 0);
MONGOOSEV_WRITE_REGISTER( MONGOOSEV_TIMER2_BASE, MONGOOSEV_TIMER_INITIAL_COUNTER_REGISTER, 0xffffffff );
MONGOOSEV_WRITE_REGISTER( MONGOOSEV_TIMER2_BASE, MONGOOSEV_TIMER_CONTROL_REGISTER, 0);
/* clear any pending interrupts */
MONGOOSEV_WRITE( MONGOOSEV_PERIPHERAL_STATUS_REGISTER, 0xffffffff );
/* clear any writable bits in the cause register */
mips_set_cause( 0 );
/* set interrupt mask, but globally off. */
/*
** Bit 15 | Bit 14 | Bit 13 | Bit 12 | Bit 11 | Bit 10 | Bit 9 | Bit 8 |
** periph | unused | FPU | unused | timer2 | timer1 | swint1 | swint2 |
** extern | | | | | | | |
**
** 1 0 1 0 0 1 0 0
**
** 0x8C00 Enable only internal Mongoose V timers.
** 0xA400 Enable Peripherial ints, FPU and timer1
** 0x0400 Timer1 only
*/
/* mips_set_sr( (SR_CU0 | SR_CU1 | 0xA400) ); */
/* to start up, only enable coprocessor 0 & timer int. per-task
** processor settings will be applied as they are created, this
** is just to configure the processor for startup
*/
mips_set_sr( (SR_CU0 | 0x400) );
mips_install_isr_entries();
}
void clear_cache( void )
{
extern void promCopyIcacheFlush(void); /* from start.S */
extern void promCopyDcacheFlush(void);
promCopyIcacheFlush();
promCopyDcacheFlush();
}
#if 0
/* Structure filled in by get_mem_info. */
struct s_mem
{
unsigned int size;
unsigned int icsize;
unsigned int dcsize;
};
extern uint32_t _RamSize;
void get_mem_info ( struct s_mem *mem )
{
mem->size = (uint32_t)&_RamSize;
mem->icsize = MONGOOSEV_IC_SIZE;
mem->dcsize = MONGOOSEV_DC_SIZE;
}
#endif