/*
* This file is the main boot and configuration file for the i386ex. It is
* solely responsible for initializing the internal register set to reflect
* the proper board configuration. This version is the "generic" i386ex
* startup:
*
* 1) 512K flask ROM @3f80000
* 2) 1 Mb RAM @ 0x0
* 3) Timer0 used as RTEMS clock ticker, 1 msec tick rate.
* 4) READY# is generated by CPU
*
* The file is a multi-section file, with sections as follows:
* 1) interrupt gates, in section "ints"
* 2) interrupt descriptor table, in section "idt"
* 3) global descriptor table, in section "gdt"
* 4) reset in section "reset"
* 5) and initial boot code in section " initial"
*
* Submitted by:
*
* Erik Ivanenko
* University of Toronto
* erik.ivanenko@utoronto.ca
*
* The license and distribution terms for this file may be
* found in the file LICENSE in this distribution or at
* http://www.OARcorp.com/rtems/license.html.
*
* $Id$
*/
#include "asm.h"
#include "macros.inc"
#include "80386ex.inc"
/*
* Needed for binutils 2.9.1.0.7 and higher
* #define NEXT_GAS
*/
EXTERN (main) /* exits to bspstart */
EXTERN (stack_start) /* defined in startup/linkcmds */
.section .idt
BEGIN_DATA
PUBLIC (Interrupt_descriptor_table)
PUBLIC(SYM(IDTR) )
SYM(IDTR): DESC3( SYM(IDT), 0x188 );
SYM (Interrupt_descriptor_table):
SYM(IDT):
SYM(GATE_DIVIDE_ERROR): INTERRUPT_GATE( DIVIDE_ERROR );
SYM(GATE_DEBUG_EXCEPTION): INTERRUPT_GATE( DEBUG_EXCEPTION );
SYM(GATE_NMI_INTERRUPT): INTERRUPT_GATE( NMI_INTERRUPT );
SYM(GATE_BREAKPOINT): INTERRUPT_GATE( BREAKPOINT );
SYM(GATE_INTO_OVERFLOW ): INTERRUPT_GATE( INTO_OVERFLOW );
SYM(GATE_BOUND_EXCEEDED ): INTERRUPT_GATE( BOUND_EXCEEDED );
SYM(GATE_INVALID_OPCODE ): INTERRUPT_GATE( INVALID_OPCODE );
SYM(GATE_COPRO_NA ): INTERRUPT_GATE( COPRO_NA );
SYM(GATE_DOUBLE_FAULT ): INTERRUPT_GATE( DOUBLE_FAULT );
SYM(GATE_COPRO_SEG_OVERRUN ): INTERRUPT_GATE( COPRO_SEG_OVERRUN );
SYM(GATE_INVALID_TSS ): INTERRUPT_GATE( INVALID_TSS );
SYM(GATE_SEGMENT_NOT_PRESENT ): INTERRUPT_GATE( SEGMENT_NOT_PRESENT );
SYM(GATE_STACK_FAULT ): INTERRUPT_GATE( STACK_FAULT );
SYM(GATE_GPF ): INTERRUPT_GATE( GPF );
SYM(GATE_PAGE_FAULT ): INTERRUPT_GATE( PAGE_FAULT );
SYM(GATE_RESERVED_1 ): INTERRUPT_GATE( RESERVED );
SYM(GATE_COPRO_ERROR ): INTERRUPT_GATE( COPRO_ERROR );
SYM(GATE_RESERVED_17): INTERRUPT_GATE( RESERVED_17 );
SYM(GATE_RESERVED_18): INTERRUPT_GATE( RESERVED_18 );
SYM(GATE_RESERVED_19): INTERRUPT_GATE( RESERVED_19 );
SYM(GATE_RESERVED_20): INTERRUPT_GATE( RESERVED_20 );
SYM(GATE_RESERVED_21): INTERRUPT_GATE( RESERVED_21 );
SYM(GATE_RESERVED_22): INTERRUPT_GATE( RESERVED_22 );
SYM(GATE_RESERVED_23): INTERRUPT_GATE( RESERVED_23 );
SYM(GATE_RESERVED_24): INTERRUPT_GATE( RESERVED_24 );
SYM(GATE_RESERVED_25): INTERRUPT_GATE( RESERVED_25 );
SYM(GATE_RESERVED_26): INTERRUPT_GATE( RESERVED_26 );
SYM(GATE_RESERVED_27): INTERRUPT_GATE( RESERVED_27 );
SYM(GATE_RESERVED_28): INTERRUPT_GATE( RESERVED_28 );
SYM(GATE_RESERVED_29): INTERRUPT_GATE( RESERVED_29 );
SYM(GATE_RESERVED_30): INTERRUPT_GATE( RESERVED_30 );
SYM(GATE_RESERVED_31): INTERRUPT_GATE( RESERVED_31 );
SYM ( GATE_TIMINT0): INTERRUPT_GATE( TIMINT0 );
SYM ( GATE_MASTER_IR2 ): INTERRUPT_GATE( MASTER_IR2 );
SYM ( GATE_SIOINT1 ): INTERRUPT_GATE( SIOINT1 );
SYM ( GATE_SIOINT2 ): INTERRUPT_GATE( SIOINT2 );
SYM ( GATE_DMAINT ): INTERRUPT_GATE( DMAINT );
SYM ( GATE_UNUSED_IR5 ): INTERRUPT_GATE( UNUSED_IR5);
SYM ( GATE_UNUSED_IR6 ): INTERRUPT_GATE( UNUSED_IR6);
SYM ( GATE_UNUSED_IR7 ): INTERRUPT_GATE( UNUSED_IR7);
SYM ( GATE_SLAVE_IR0 ): INTERRUPT_GATE( SLAVE_IR0 );
SYM ( GATE_SLAVE_IR1 ): INTERRUPT_GATE( SLAVE_IR1 );
SYM ( GATE_SLAVE_IR2 ): INTERRUPT_GATE( SLAVE_IR2 );
SYM ( GATE_SLAVE_IR3 ): INTERRUPT_GATE( SLAVE_IR3 );
SYM ( GATE_SLAVE_IR4 ): INTERRUPT_GATE( SLAVE_IR4 );
SYM ( GATE_SLAVE_IR5 ): INTERRUPT_GATE( SLAVE_IR5 );
SYM ( GATE_SLAVE_IR6 ): INTERRUPT_GATE( SLAVE_IR6 );
SYM ( GATE_SLAVE_IR7 ): INTERRUPT_GATE( SLAVE_IR7 );
END_DATA
.section .gdt
BEGIN_DATA
PUBLIC (_Global_descriptor_table)
SYM(GDTR): DESC3( GDT_TABLE, 0x1f ); # one less than the size
SYM (_Global_descriptor_table):
SYM(GDT):
SYM(GDT_TABLE): DESC2(0,0,0,0,0,0);
SYM(GDT_ALIAS): DESC2(32,0x1000,0x0,0x93,0,0x0);
SYM(GDT_CODE): DESC2(0xffff,0,0x0,0x9B,0xDF,0x00);
SYM(GDT_DATA): DESC2(0xffff,0,0x0,0x92,0xDF,0x00); # was CF
SYM(GDT_END):
END_DATA
/* This section is the section that is used by the interrupt
descriptor table. It is used to provide the IDT with the
correct vector offsets. It is for symbol definition only.
*/
.section .ints
SYM(INTERRUPT_HANDLERS):
SYM(DIVIDE_ERROR): jmp SYM(DIVIDE_ERROR)
SYM(DEBUG_EXCEPTION): jmp SYM(DEBUG_EXCEPTION)
SYM(NMI_INTERRUPT): jmp SYM(NMI_INTERRUPT)
SYM(BREAKPOINT): jmp SYM(BREAKPOINT)
SYM(INTO_OVERFLOW): jmp SYM(INTO_OVERFLOW)
SYM(BOUND_EXCEEDED): jmp SYM(BOUND_EXCEEDED)
SYM(INVALID_OPCODE): jmp SYM(INVALID_OPCODE)
SYM(COPRO_NA): jmp SYM(COPRO_NA)
SYM(DOUBLE_FAULT): jmp SYM(DOUBLE_FAULT)
SYM(COPRO_SEG_OVERRUN): jmp SYM(COPRO_SEG_OVERRUN)
SYM(INVALID_TSS): jmp SYM(INVALID_TSS)
SYM(RESERVED): JMP SYM(RESERVED)
SYM(COPRO_ERROR): JMP SYM(COPRO_ERROR)
SYM(PAGE_FAULT): JMP SYM(PAGE_FAULT)
SYM(GPF): JMP SYM(GPF)
SYM(STACK_FAULT): JMP SYM(STACK_FAULT)
SYM(SEGMENT_NOT_PRESENT): jmp SYM(SEGMENT_NOT_PRESENT)
SYM(RESERVED_17): jmp SYM(RESERVED_17)
SYM(RESERVED_18): jmp SYM(RESERVED_18)
SYM(RESERVED_19): jmp SYM(RESERVED_19)
SYM(RESERVED_20): jmp SYM(RESERVED_20)
SYM(RESERVED_21): jmp SYM(RESERVED_21)
SYM(RESERVED_22): jmp SYM(RESERVED_22)
SYM(RESERVED_23): jmp SYM(RESERVED_23)
SYM(RESERVED_24): jmp SYM(RESERVED_24)
SYM(RESERVED_25): jmp SYM(RESERVED_25)
SYM(RESERVED_26): jmp SYM(RESERVED_26)
SYM(RESERVED_27): jmp SYM(RESERVED_27)
SYM(RESERVED_28): jmp SYM(RESERVED_28)
SYM(RESERVED_29): jmp SYM(RESERVED_29)
SYM(RESERVED_30): jmp SYM(RESERVED_30)
SYM(RESERVED_31): jmp SYM(RESERVED_31)
SYM(TIMINT0): nop; iret
SYM(MASTER_IR2): jmp SYM(MASTER_IR2)
SYM(SIOINT1): jmp SYM(SIOINT1)
SYM(SIOINT2): jmp SYM(SIOINT2)
SYM(DMAINT): jmp SYM(DMAINT)
SYM(UNUSED_IR5): jmp SYM(UNUSED_IR5)
SYM(UNUSED_IR6): JMP SYM(UNUSED_IR6)
SYM(UNUSED_IR7): JMP SYM(UNUSED_IR7)
SYM(SLAVE_IR0): JMP SYM(SLAVE_IR0)
SYM(SLAVE_IR1): JMP SYM(SLAVE_IR1)
SYM(SLAVE_IR2): nop; iret
SYM(SLAVE_IR3): JMP SYM(SLAVE_IR3)
SYM(SLAVE_IR4): JMP SYM(SLAVE_IR4)
SYM(SLAVE_IR5): JMP SYM(SLAVE_IR5)
SYM(SLAVE_IR6): JMP SYM(SLAVE_IR6)
SYM(SLAVE_IR7): JMP SYM(SLAVE_IR7)
PUBLIC( SYM(_initInternalRegisters) )
.section .reset
PUBLIC ( SYM(reset) )
SYM(reset):
.code16
nop
cli
#ifdef NEXT_GAS
addr32
#endif
jmp SYM(_initInternalRegisters) /* different section in this file */
.code32 /* in case this section moves */
nop /* required by CHIP LAB to pad out size */
nop
nop
nop
nop
.section .initial
/*
* Enable access to peripheral register at expanded I/O addresses
*/
SYM(_initInternalRegisters):
.code16
movw $0x8000 , ax
outb al , $REMAPCFGH
xchg al , ah
outb al,$REMAPCFGL
outw ax, $REMAPCFG ;
/*
* Configure operation of the A20 Address Line
*/
SYM(A20):
movw $PORT92 , dx
inb dx , al # clear A20 port reset
andb $0xfe , al # b0 Fast Reset(0)=disabled,(1)=reset triggered
orb $0x02 , al # Bit 1 Fast A20 = 0 (always 0) else enabled.
outb al , dx
SYM(Watchdog):
SetExRegByte( WDTSTATUS, 0x01 ) # disable watchdog timer
/*
* Initialize Refresh Control Unit for:
* Refresh Address = 0x0000
* Refresh gate between rows is 15.6 uSec
* Using a CLK2 frequency of 50Mhz ( 25Mhz CPU )
* The refresh unit is enabled
* The refresh pin is not used.
*/
SYM(InitRCU):
SetExRegWord( RFSCIR , 390) # refresh interval was 390, tried 312
SetExRegWord( RFSBAD , 0x0) # base address
SetExRegWord( RFSADD , 0x0) # address register
SetExRegWord( RFSCON , 0x8000) # enable bit
/*
* Initialize clock and power mgmt unit for:
* Clock Frequency = 50 Mhz
* Prescaled clock output = 1.19318 Mhz
* ( matches standard PC )
* Normal halt instructions
*/
SYM(InitClk):
SetExRegByte( PWRCON, 0x0 )
SetExRegWord( CLKPRS, 0x13)
/**************************************************************
* Initialize the Pin Configurations
*************************************************************/
/*
* Initialize I/O port 1 for:
* PIN 0 = 1, DCD0# to package pin
* PIN 1 = 1, RTS0# to package pin
* PIN 2 = 1, DTR0# to package pin
* PIN 3 = 1, DSR0# to package pin
* PIN 4 = 1, RI0# to package pin
* PIN 5 = 0, Outport (FLASH Vpp Enable, 0=Enable 1=Disable)
* PIN 6 = 0, Outport (P16_HOLD to 386ex option header JP7 pin 5)
* PIN 7 = 0, Outport (P17_HOLD to 386ex option header JP7 pin 3)
*/
SYM(InitPort1):
SetExRegByte( P1LTC , 0xff )
SetExRegByte( P1DIR , 0x0 )
SetExRegByte( P1CFG , 0x1f)
/*
* Initialize I/O port 2 for:
* PIN 0 = 0, Outport (P20_CS0# to 386ex option header JP7 pin 11)
* PIN 1 = 0, Outport (P21_CS1# to 386ex option header JP7 pin 9)
* PIN 2 = 1, CS2# (SMRAM) If not using CS2 can be configured as.?
* PIN 3 = 0, Outport ( no connect )
* PIN 4 = 1, CS#4 (DRAM)
* PIN 5 = 1, RXD0 input. See not for I/0 port 1 pins 1-4
* PIN 6 = 1, TXD0 output.
* PIN 7 = 1, CTS0# input.
*/
SYM(InitPort2):
SetExRegByte( P2LTC , 0xff )
SetExRegByte( P2DIR , 0x0 )
SetExRegByte( P2CFG , 0xfe)
/*
* Initialize I/O port 3 P3CFG
* PIN 0 = 1, TMROUT0 to package pin
* PIN 1 = 0, (TMROUT1 to 386ex option header JP7 pin 23)
* PIN 2 = 0, INT0 (IR1) disabled, (P3.2 out to JP7 pin 21)
* PIN 3 = 0, INT1 (IR5) disbled (P3.3 to option header JP7 pin 19)
* PIN 4 = 0, INT2 (IR6) disbled (P3.4 to option header JP7 pin 17)
* PIN 5 = 0, INT2 (IR7) disabled (P3.5 to 386ex header JP7 pin 15)
* PIN 6 = 0, Inport (Debugger Break P3.6/PWRD to package pin )
* P3.6 selected
* PIN 7 = 0, COMCLK output disabled, 1.8432 Mhz OSC1 oscillator.
* ( Debbugger uses COMCLK as the clocking source )
* P3.7 connected to package pin.
*/
SYM(InitPort3):
SetExRegByte( P3LTC , 0xff )
SetExRegByte( P3DIR , 0x41 )
SetExRegByte( P3CFG , 0x09 ) # can check TMROUT0
/*
* Initialize Peripheral Pin Configurations:
* PIN 0 = 1, RTS1# to package pin
* PIN 1 = 1, DTR1# to package pin
* PIN 2 = 1, TXD1 out to package pin
* PIN 3 = 0, EOP#/TC
* PIN 4 = 0, DACK0#
* PIN 5 = 1, Timer2
* PIN 6 = 0, 0 => CS6# connected to package pin
* PIN 7 = 0, Don't care
*/
SYM(InitPeriph):
SetExRegByte( PINCFG , 0x24)
/*
* Initialize the Asynchronous Serial Ports:
* BIT 7 = 1, Internal SIO1 modem signals
* BIT 6 = 1, Internal SIO0 modem signals
* BIT 2 = 0, PSCLK for SSIO clock
* BIT 1 = 1, SERCLK for SIO1 clock
* BIT 0 = 1, SERCLK for SIO0 clock
*/
SYM(InitSIO):
SetExRegByte( SIOCFG, 0xC3 ) # SIOn clocked internally
SetExRegByte( LCR0, 0x80 ) # latch DLL0, DLH0
SetExRegByte( DLL0, 0x51 ) # 0x51 sets to 9600 baud 0x7 -> 115,200
SetExRegByte( DLH0, 0x00 ) # 0x145 is 2400 baud
SetExRegByte( LCR0, 0x03 ) # enable r/w buffers, IER0 accessible
# mode 8-n-1
SetExRegByte( IER0, 0x00 ) # was 0x0f All interrupts detected
SetExRegByte( LCR1, 0x80 ) # latch DLL0, DLH0
SetExRegByte( DLL1, 0x51 ) # 0x51 set to 9600 baud, 0x7 = 115200
SetExRegByte( DLH1, 0x00 ) # 0x145 is 2400 baud
SetExRegByte( LCR1, 0x03 ) # enable r/w buffers, IER1 accessible
# reg 8-n-1
SetExRegByte( IER1, 0x00 ) # was 0x0f - All interrupts detected
SYM(InitMCR):
/*
* Initialize Timer for:
* BIT 7 = 1, Timer clocks disabled
* BIT 6 = 0, Reserved
* BIT 5 = 1, TMRCLK2 instead of Vcc to Gate2
* BIT 4 = 0, PSCLK to CLK2
* BIT 3 = 1, TMRCLK1 instead of Vcc to Gate1
* BIT 2 = 0, PSCLK to Gate1
* BIT 1 = 0, Vcc to Gate0
* BIT 0 = 0, PSCLK to Gate0
*/
SYM(InitTimer):
SetExRegByte(TMRCFG , 0x80 ) # All counters disabled, Gates 0,1
# and 2 are set to Vcc
SetExRegByte(TMRCON , 0x34 ) # prepare to write counter 0 LSB,MSB
SetExRegByte(TMR0 , 0xA8 ) # LSB = 0B count, followed by MSB
SetExRegByte(TMR0 , 0x04 ) # for INT every 50 msec. MSB = 0xE900
# for INT every 5 msec. 0x174c
# for INT every 1 msec. 0x04A8
# was 0xe900
SetExRegByte(TMRCON , 0x70 ) # mode 0 disables on Gate= Vcc
SetExRegByte(TMR1 , 0x00 ) # sfa
SetExRegByte(TMR1 , 0x00 ) # sfa
SetExRegByte(TMRCON , 0xB0 ) # mode 0 disables on gate =Vcc
SetExRegByte(TMR2 , 0x00 ) #
SetExRegByte(TMR2 , 0x00 ) #
SetExRegByte(TMRCFG , 0x80 ) # Enable timers = 0x00
/*
* Initialize the DMACFG register for:
* BIT 7 = 1 , Disable DACK#1
* BITs 6:4 = 100, TMROUT2 connected to DRQ1
* BIT 3 = 1 , Disable DACK0#
* BIT 2:0 = 000, Pin is connected to DRQ0
*/
SetExRegByte(DMACFG , 0xC0 )
SetExRegByte(DMACMD1, 0x00 ) # disable both DMA channels
SetExRegByte(DMAMOD1, 0x40 )
/*
* Initialize the INTCFG register for:
* BIT 7 = 0, 8259 cascade disabled
* BIT 3 = 0, SLAVE IR6 connected to Vss
* BIT 2 = 0, SLAVE IR5 connected to Vss
* BIT 1 = 0, SLAVE IR1 connected to SSIOINT
* BIT 0 = 0, SLAVE IR0 connected to Vss
*/
SYM(InitInt):
cli # !
SetExRegByte(ICW1S , 0x11 ) # EDGE TRIGGERED
SetExRegByte(ICW2S , 0x28 ) # Slave base vector after Master
SetExRegByte(ICW3S , 0x04 ) # ( was 0x02! )slave cascaded to IR2 on master
SetExRegByte(ICW4S , 0x01 ) # must be 0x01
SetExRegByte(ICW1M , 0x11 ) # edge triggered
SetExRegByte(ICW2M , 0x20 ) # base vector starts at byte 32
SetExRegByte(ICW3M , 0x02 ) # IR2 is cascaded internally
SetExRegByte(ICW4M , 0x01 ) # idem
SetExRegByte(OCW1M , 0xde ) # IR0 only = 0xfe. for IR5 and IR0 active use 0xde
SetExRegByte(INTCFG , 0x00 )
SYM(SetCS4):
SetExRegWord(CS4ADL , 0x702) #Configure chip select 4
SetExRegWord(CS4ADH , 0x00)
SetExRegWord(CS4MSKH, 0x03F)
SetExRegWord(CS4MSKL, 0xFC01)
SYM(SetUCS1):
SetExRegWord(UCSADL , 0x0304) # 512K block starting at 0x80000 until 0x3f80000
SetExRegWord(UCSADH , 0x03F8)
SetExRegWord(UCSMSKH, 0x03F7)
SetExRegWord(UCSMSKL, 0xFC01) # configure upper chip select
SYM(xfer_idt):
movw $ _ram_idt_offset , di
movw $ _ram_idt_segment , cx
mov cx, es
movw $ _rom_idt_offset , si
movw $ _rom_idt_segment , ax
mov ax , ds
movw $ _idt_size , cx
repne
movsb
SYM(xfer_ints):
movw $ _ram_ints_offset , di
movw $ _ram_ints_segment , ax
mov ax , es
movw $ _rom_ints_offset , si
movw $ _rom_ints_segment, ax
mov ax , ds
movw $ _ints_size , cx
repne
movsb
SYM(lidt):
movw $ _ram_idt_offset , di
movw $ 0x0 , si
movw $ _ram_idt_segment , ax
mov ax , ds
lidt _ram_idt_offset
SYM(xfer_gdt):
movw $ _ram_gdt_offset , di
movw $ _ram_gdt_segment , cx
mov cx , es
movw $ _gdt_size , cx
movw $ _rom_gdt_segment , ax
movw $ _rom_gdt_offset , si
mov ax , ds
repne
movsb
/*****************************
* Load the Global Descriptor
* Table Register
****************************/
movw $ _ram_gdt_segment, ax
mov ax , ds
#ifdef NEXT_GAS
data32
addr32
#endif
lgdt _ram_gdt_offset # location of GDT
SYM(SetUCS):
SetExRegWord(UCSADL, 0x0704) # now 512K starting at 0x3f80000.
SetExRegWord(UCSADH, 0x03f8)
SetExRegWord(UCSMSKH, 0x0007)
SetExRegWord(UCSMSKL, 0xFC01) # configure upper chip select
/***************************
* Switch to Protected Mode
***************************/
mov cr0, eax
orw $0x1, ax
mov eax, cr0
/**************************
* Flush prefetch queue,
* and load CS selector
*********************/
ljmpl $ GDT_CODE_PTR , $ SYM(_copy_data) # sets the code selector
/*
* Copy the data section down to RAM
*/
SYM(_copy_data):
.code32
pLOAD_SEGMENT( GDT_DATA_PTR, fs)
pLOAD_SEGMENT( GDT_DATA_PTR, gs)
pLOAD_SEGMENT( GDT_DATA_PTR, ss)
pLOAD_SEGMENT( GDT_DATA_PTR, ds)
pLOAD_SEGMENT( GDT_DATA_PTR, es)
movl $ SYM(_data_start) , edi # ram destination
movl $ SYM(_rom_data_start) , esi # rom data source
movl $ SYM(_edata) , ecx # end of data section
subl $ SYM(_data_start) , ecx # length of data section
# es, ds preloaded
repne # while ecx != 0
movsb # move a byte
/*
* Set up the stack
*/
SYM (_establish_stack):
movl $end, eax # stack starts right after bss
/* movl eax, stack_start # save for brk() routine */
movl $stack_origin, esp # this is the high starting address
movl $stack_origin, ebp
/*
* Zero out the BSS segment
*/
SYM (zero_bss):
cld # make direction flag count up
movl $ SYM (end),ecx # find end of .bss
movl $ SYM (_bss_start),edi # edi = beginning of .bss
subl edi,ecx # ecx = size of .bss in bytes
shrl ecx # size of .bss in longs
shrl ecx
xorl eax,eax # value to clear out memory
repne # while ecx != 0
stosl # clear a long in the bss
/*
* Transfer control to User's Board Support Package
*/
pushl $0 # environp
pushl $0 # argv
pushl $0 # argc
call SYM (main) # does not return
addl $12,esp
BEGIN_DATA_DCL
/* .align 2
PUBLIC (start_frame)
SYM (start_frame):
.long 0
*/
/* PUBLIC (stack_start)
SYM (stack_start):
.long 0
*/
END_DATA_DCL
END
