blob: d9e99263f1eca211057a178862f8a51f8d7cf2d8 (
plain) (
tree)
|
|
/* bsp.h
*
* This include file definitions related to the Force CPU-386 board.
*
* COPYRIGHT (c) 1989-1997.
* On-Line Applications Research Corporation (OAR).
* Copyright assigned to U.S. Government, 1994.
*
* The license and distribution terms for this file may be
* found in the file LICENSE in this distribution or at
* http://www.OARcorp.com/rtems/license.html.
*
* $Id$
*/
#ifndef __FORCE386_h
#define __FORCE386_h
#ifdef __cplusplus
extern "C" {
#endif
#include <rtems.h>
#include <iosupp.h>
#include <console.h>
#include <clockdrv.h>
/*
* Define the time limits for RTEMS Test Suite test durations.
* Long test and short test duration limits are provided. These
* values are in seconds and need to be converted to ticks for the
* application.
*
*/
#define MAX_LONG_TEST_DURATION 300 /* 5 minutes = 300 seconds */
#define MAX_SHORT_TEST_DURATION 3 /* 3 seconds */
/*
* Define the interrupt mechanism for Time Test 27
*
* NOTE: Use a software interrupt for the i386.
*/
#define MUST_WAIT_FOR_INTERRUPT 0
#define Install_tm27_vector( handler ) set_vector( (handler), 0x90, 1 )
#define Cause_tm27_intr() asm volatile( "int $0x90" : : );
#define Clear_tm27_intr()
#define Lower_tm27_intr()
/*
* Simple spin delay in microsecond units for device drivers.
* This is very dependent on the clock speed of the target.
*/
#define delay( _microseconds ) \
{ \
rtems_unsigned32 _counter; \
\
_counter = (_microseconds); \
\
asm volatile ( "0: nop;" \
" mov %0,%0 ;" \
" loop 0b" : "=c" (_counter) \
: "0" (_counter) \
); \
\
}
/* Constants */
#define RAM_START 0
#define RAM_END 0x100000
/* I/O addressing */
/*
* The following determines whether Port B or the Console should
* be used for test I/O. Setting ONE (and only ONE) of these to 1
* enables I/O on that port.
*
* PORT A - DUSCC MC68562 Channel A
* PORT B - DUSCC MC68562 Channel B
* PORT C - MFP MC68901 Channel (*** FORCEbug console ***)
*/
#define PORTB 1 /* use port b as test port */
#define PORTC 0 /* use console port as test port */
#if ( PORTB == 1 )
#define TX_STATUS 0x1b6 /* DUSCC General Status Register */
#define RX_STATUS 0x1b6 /* DUSCC General Status Register */
#define TX_BUFFER 0x1e0 /* DUSCC Transmitter Channel B */
#define RX_BUFFER 0x1e8 /* DUSCC Receiver Channel B */
#define Is_tx_ready( _status ) ( (_status) & 0x20 )
#define Is_rx_ready( _status ) ( (_status) & 0x10 )
#endif
#if ( PORTC == 1 )
#define TX_STATUS 0x12c /* MFP Transmit Status Register */
#define RX_STATUS 0x12a /* MFP Receive Status Register */
#define TX_BUFFER 0x12e /* MFP Transmitter Channel */
#define RX_BUFFER 0x12e /* MFP Receiver Channel */
#define Is_tx_ready( _status ) ( (_status) & 0x80 )
#define Is_rx_ready( _status ) ( (_status) & 0x80 )
#endif
/* Timer constants */
#define IERA 0x106 /* Interrupt Enable Register A */
#define IMRA 0x112 /* Interrupt Mask Register A */
#define TACR 0x118 /* Timer A Control Register */
#define TADR 0x11e /* Timer A Data Register */
#define IERB 0x108 /* Interrupt Enable Register B */
#define TBCR 0x11a /* Timer B Control Register */
#define TBDR 0x120 /* Timer B Data Register */
/* Structures */
#ifdef F386_INIT
#undef BSP_EXTERN
#define BSP_EXTERN
#else
#undef BSP_EXTERN
#define BSP_EXTERN extern
#endif
/*
* Device Driver Table Entries
*/
/*
* NOTE: Use the standard Console driver entry
*/
/*
* NOTE: Use the standard Clock driver entry
*/
/*
* How many libio files we want
*/
#define BSP_LIBIO_MAX_FDS 20
/* miscellaneous stuff assumed to exist */
extern rtems_configuration_table BSP_Configuration;
extern i386_IDT_slot Interrupt_descriptor_table[ 256 ];
extern i386_GDT_slot Global_descriptor_table[ 8192 ];
BSP_EXTERN unsigned short Idt[3]; /* Interrupt Descriptor Table Address */
BSP_EXTERN unsigned short Gdt[3]; /* Global Descriptor Table Address */
BSP_EXTERN unsigned int Idt_base;
BSP_EXTERN unsigned int Gdt_base;
/* routines */
i386_isr_entry set_vector(
rtems_isr_entry handler,
rtems_vector_number vector,
int type
);
#ifdef __cplusplus
}
#endif
#endif
/* end of include file */
|
