/**
* @file
*
* @ingroup RTEMSBSPsPowerPCMotorola
*
* @brief Global BSP definitions.
*/
/*
*
* The license and distribution terms for this file may be
* found in the file LICENSE in this distribution or at
* http://www.rtems.org/license/LICENSE.
*/
#ifndef LIBBSP_POWERPC_MOTOROLA_POWERPC_BSP_H
#define LIBBSP_POWERPC_MOTOROLA_POWERPC_BSP_H
/**
* @defgroup RTEMSBSPsPowerPCMotorola Motorola
*
* @ingroup RTEMSBSPsPowerPC
*
* @brief Motorola Board Support Package.
*
* @{
*/
#include <bspopts.h>
#include <bsp/default-initial-extension.h>
#include <rtems.h>
#include <libcpu/io.h>
#include <bsp/vectors.h>
#ifdef qemu
#include <rtems/bspcmdline.h>
#endif
#ifdef __cplusplus
extern "C" {
#endif
/*
* diagram illustrating the role of the configuration
* constants
* PCI_MEM_WIN0: CPU starting addr where PCI memory space is visible
* PCI_MEM_BASE: CPU address of PCI mem addr. zero. (regardless of this
* address being 'visible' or not!).
* _VME_A32_WIN0_ON_PCI: PCI starting addr of the 1st window to VME
* _VME_A32_WIN0_ON_VME: VME address of that same window
*
* AFAIK, only PreP boards have a non-zero PCI_MEM_BASE (i.e., an offset between
* CPU and PCI addresses). The mvme2300 'ppcbug' firmware configures the PCI
* bus using PCI base addresses! I.e., drivers need to add PCI_MEM_BASE to
* the base address read from PCI config.space in order to translate that
* into a CPU address.
*
* NOTE: VME addresses should NEVER be translated using these constants!
* they are strictly for BSP internal use. Drivers etc. should use
* the translation routines int VME.h (BSP_vme2local_adrs/BSP_local2vme_adrs).
*
* CPU ADDR PCI_ADDR VME ADDR
*
* 00000000 XXXXXXXX XXXXXXXX
* ^ ^ ........
* | |
* | | e.g., RAM XXXXXXXX
* | | 00000000
* | | ......... ^
* | | (possible offset |
* | | between pci and XXXXXXXX | ......
* | | cpu addresses) |
* | v |
* | PCI_MEM_BASE -------------> 00000000 --------------- |
* | ........ ........ ^ |
* | invisible | |
* | ........ from CPU | |
* v | |
* PCI_MEM_WIN0 ============= first visible PCI addr | |
* | |
* pci devices pci window | |
* visible here v v
* mapped by ========== _VME_A32_WIN0_ON_PCI ======= _VME_A32_WIN0_ON_VME
* vme window
* VME devices hostbridge mapped by
* visible here universe
* =====================================================
*
*/
/* fundamental addresses for BSP (CHRPxxx and PREPxxx are from libcpu/io.h) */
#if defined(mvme2100)
#define _IO_BASE CHRP_ISA_IO_BASE
#define _ISA_MEM_BASE CHRP_ISA_MEM_BASE
/* address of our ram on the PCI bus */
#define PCI_DRAM_OFFSET CHRP_PCI_DRAM_OFFSET
/* offset of pci memory as seen from the CPU */
#define PCI_MEM_BASE 0
/* where (in CPU addr. space) does the PCI window start */
#define PCI_MEM_WIN0 0x80000000
#else
#define _IO_BASE PREP_ISA_IO_BASE
#define _ISA_MEM_BASE PREP_ISA_MEM_BASE
#ifndef qemu
/* address of our ram on the PCI bus */
#define PCI_DRAM_OFFSET PREP_PCI_DRAM_OFFSET
/* offset of pci memory as seen from the CPU */
#define PCI_MEM_BASE PREP_ISA_MEM_BASE
#define PCI_MEM_WIN0 0
#else
#define PCI_DRAM_OFFSET 0
#define PCI_MEM_BASE 0
#define PCI_MEM_WIN0 PREP_ISA_MEM_BASE
#endif
#endif
/*
* The BSP has PCI devices. Enable support in LibBSD.
*/
#define BSP_HAS_PC_PCI
/*
* Remap the PCI address space for LibBSD
*/
#define RTEMS_BSP_PCI_IO_REGION_BASE 0
#define RTEMS_BSP_PCI_MEM_REGION_BASE PCI_DRAM_OFFSET
/*
* Remap the PCI address space for LibBSD
*/
#define RTEMS_BSP_ADDR_PTR(_type) uint ## _type ## _t __volatile*
#define RTEMS_BSP_ADDR_CPTR(_type) const RTEMS_BSP_ADDR_PTR(_type)
#define RTEMS_BSP_ADDRESS_READ(_addr, _type) \
*((RTEMS_BSP_ADDR_CPTR(_type)) (((RTEMS_BSP_ADDR_CPTR(8)) _addr) + PCI_DRAM_OFFSET))
#define RTEMS_BSP_ADDRESS_WRITE(_addr, _val, _type) \
*((RTEMS_BSP_ADDR_PTR(_type)) (((RTEMS_BSP_ADDR_PTR(8)) _addr) + PCI_DRAM_OFFSET)) = (_val)
#define RTEMS_BSP_READ_1(_addr) RTEMS_BSP_ADDRESS_READ(_addr, 8)
#define RTEMS_BSP_READ_2(_addr) RTEMS_BSP_ADDRESS_READ(_addr, 16)
#define RTEMS_BSP_READ_4(_addr) RTEMS_BSP_ADDRESS_READ(_addr, 32)
#define RTEMS_BSP_READ_8(_addr) RTEMS_BSP_ADDRESS_READ(_addr, 64)
#define RTEMS_BSP_WRITE_1(_addr, _val) RTEMS_BSP_ADDRESS_WRITE(_addr, _val, 8)
#define RTEMS_BSP_WRITE_2(_addr, _val) RTEMS_BSP_ADDRESS_WRITE(_addr, _val, 16)
#define RTEMS_BSP_WRITE_4(_addr, _val) RTEMS_BSP_ADDRESS_WRITE(_addr, _val, 32)
#define RTEMS_BSP_WRITE_8(_addr, _val) RTEMS_BSP_ADDRESS_WRITE(_addr, _val, 64)
/*
* Base address definitions for several devices
*
* MVME2100 is very similar but has fewer devices and uses on-CPU EPIC
* implementation of OpenPIC controller. It also cannot be probed to
* find out what it is which is VERY different from other Motorola boards.
*/
#if defined(mvme2100)
#define BSP_UART_IOBASE_COM1 ((_IO_BASE)+0x01e10000)
/* #define BSP_UART_IOBASE_COM1 (0xffe10000) */
#define BSP_OPEN_PIC_BASE_OFFSET 0x40000
#define MVME_HAS_DEC21140
#else
#define BSP_UART_IOBASE_COM1 ((_IO_BASE)+0x3f8)
#define BSP_UART_IOBASE_COM2 ((_IO_BASE)+0x2f8)
#if ! defined(qemu)
#define BSP_KBD_IOBASE ((_IO_BASE)+0x60)
#define BSP_VGA_IOBASE ((_IO_BASE)+0x3c0)
#endif
#if defined(mvme2300)
#define MVME_HAS_DEC21140
#endif
#endif
#define BSP_CONSOLE_PORT BSP_UART_COM1
#define BSP_UART_BAUD_BASE 115200
struct rtems_bsdnet_ifconfig;
#if defined(MVME_HAS_DEC21140)
#define RTEMS_BSP_NETWORK_DRIVER_NAME "dc1"
#define RTEMS_BSP_NETWORK_DRIVER_ATTACH rtems_dec21140_driver_attach
extern int rtems_dec21140_driver_attach(struct rtems_bsdnet_ifconfig *, int);
#endif
#ifdef qemu
#define RTEMS_BSP_NETWORK_DRIVER_NAME "ne1"
#define RTEMS_BSP_NETWORK_DRIVER_ATTACH rtems_ne_driver_attach
extern int rtems_ne_driver_attach(struct rtems_bsdnet_ifconfig *, int);
RTEMS_INLINE_ROUTINE const char* bsp_cmdline_arg(const char* arg)
{
return rtems_bsp_cmdline_get_param_raw(arg);
}
#endif
#ifdef qemu
#define BSP_IDLE_TASK_BODY bsp_ppc_idle_task_body
extern void *bsp_ppc_idle_task_body(uintptr_t arg);
#endif
#include <bsp/openpic.h>
/* BSP_PIC_DO_EOI is optionally used by the 'vmeUniverse' driver
* to implement VME IRQ priorities in software.
* Note that this requires support by the interrupt controller
* driver (cf. libbsp/shared/powerpc/irq/openpic_i8259_irq.c)
* and the BSP-specific universe initialization/configuration
* (cf. libbsp/shared/powerpc/vme/VMEConfig.h vme_universe.c)
*
* ********* IMPORTANT NOTE ********
* When deriving from this file (new BSPs)
* DO NOT define "BSP_PIC_DO_EOI" if you don't know what
* you are doing i.e., w/o implementing the required pieces
* mentioned above.
* ********* IMPORTANT NOTE ********
*/
#define BSP_PIC_DO_EOI openpic_eoi(0)
#ifndef ASM
#define outport_byte(port,value) outb(value,port)
#define outport_word(port,value) outw(value,port)
#define outport_long(port,value) outl(value,port)
#define inport_byte(port,value) (value = inb(port))
#define inport_word(port,value) (value = inw(port))
#define inport_long(port,value) (value = inl(port))
/*
* Vital Board data Start using DATA RESIDUAL
*/
/*
* Total memory using RESIDUAL DATA
*/
extern unsigned int BSP_mem_size;
/*
* Start of the heap
*/
extern unsigned int BSP_heap_start;
/*
* PCI Bus Frequency
*/
extern unsigned int BSP_bus_frequency;
/*
* processor clock frequency
*/
extern unsigned int BSP_processor_frequency;
/*
* Time base divisior (how many tick for 1 second).
*/
extern unsigned int BSP_time_base_divisor;
/*
* String passed by the bootloader.
*/
extern char *BSP_commandline_string;
#define BSP_Convert_decrementer( _value ) \
((unsigned long long) ((((unsigned long long)BSP_time_base_divisor) * 1000000ULL) /((unsigned long long) BSP_bus_frequency)) * ((unsigned long long) (_value)))
/* extern int printk(const char *, ...) __attribute__((format(printf, 1, 2))); */
extern int BSP_disconnect_clock_handler (void);
extern int BSP_connect_clock_handler (void);
/* clear hostbridge errors
*
* NOTE: The routine returns always (-1) if 'enableMCP==1'
* [semantics needed by libbspExt] if the MCP input is not wired.
* It returns and clears the error bits of the PCI status register.
* MCP support is disabled because:
* a) the 2100 has no raven chip
* b) the raven (2300) would raise machine check interrupts
* on PCI config space access to empty slots.
*/
extern unsigned long _BSP_clear_hostbridge_errors(int enableMCP, int quiet);
/*
* Prototypes for methods called only from .S for dependency tracking
*/
char *save_boot_params(
void *r3,
void *r4,
void *r5,
char *cmdline_start,
char *cmdline_end
);
void zero_bss(void);
/*
* Prototypes for BSP methods which cross file boundaries
*/
void VIA_isa_bridge_interrupts_setup(void);
#endif
#ifdef __cplusplus
};
#endif
/** @} */
#endif