|
|
/*-
* SPDX-License-Identifier: BSD-4-Clause
*
* Copyright (c) 2003
* Bill Paul <wpaul@windriver.com>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD$
*/
#ifndef _DEV_MII_RGEPHYREG_H_
#define _DEV_MII_RGEPHYREG_H_
#define RGEPHY_8211B 2
#define RGEPHY_8211C 3
#define RGEPHY_8211F 6
/*
* RealTek 8169S/8110S gigE PHY registers
*/
#define RGEPHY_MII_BMCR 0x00
#define RGEPHY_BMCR_RESET 0x8000
#define RGEPHY_BMCR_LOOP 0x4000
#define RGEPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */
#define RGEPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */
#define RGEPHY_BMCR_PDOWN 0x0800 /* Power down */
#define RGEPHY_BMCR_ISO 0x0400 /* Isolate */
#define RGEPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */
#define RGEPHY_BMCR_FDX 0x0100 /* Duplex mode */
#define RGEPHY_BMCR_CTEST 0x0080 /* Collision test enable */
#define RGEPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */
#define RGEPHY_S1000 RGEPHY_BMCR_SPD1 /* 1000mbps */
#define RGEPHY_S100 RGEPHY_BMCR_SPD0 /* 100mpbs */
#define RGEPHY_S10 0 /* 10mbps */
#define RGEPHY_MII_BMSR 0x01
#define RGEPHY_BMSR_100T4 0x8000 /* 100 base T4 capable */
#define RGEPHY_BMSR_100TXFDX 0x4000 /* 100 base Tx full duplex capable */
#define RGEPHY_BMSR_100TXHDX 0x2000 /* 100 base Tx half duplex capable */
#define RGEPHY_BMSR_10TFDX 0x1000 /* 10 base T full duplex capable */
#define RGEPHY_BMSR_10THDX 0x0800 /* 10 base T half duplex capable */
#define RGEPHY_BMSR_100T2FDX 0x0400 /* 100 base T2 full duplex capable */
#define RGEPHY_BMSR_100T2HDX 0x0200 /* 100 base T2 half duplex capable */
#define RGEPHY_BMSR_EXTSTS 0x0100 /* Extended status present */
#define RGEPHY_BMSR_PRESUB 0x0040 /* Preamble surpression */
#define RGEPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */
#define RGEPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occurred */
#define RGEPHY_BMSR_ANEG 0x0008 /* Autoneg capable */
#define RGEPHY_BMSR_LINK 0x0004 /* Link status */
#define RGEPHY_BMSR_JABBER 0x0002 /* Jabber detected */
#define RGEPHY_BMSR_EXT 0x0001 /* Extended capability */
#define RGEPHY_MII_ANAR 0x04
#define RGEPHY_ANAR_NP 0x8000 /* Next page */
#define RGEPHY_ANAR_RF 0x2000 /* Remote fault */
#define RGEPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */
#define RGEPHY_ANAR_PC 0x0400 /* Pause capable */
#define RGEPHY_ANAR_T4 0x0200 /* local device supports 100bT4 */
#define RGEPHY_ANAR_TX_FD 0x0100 /* local device supports 100bTx FD */
#define RGEPHY_ANAR_TX 0x0080 /* local device supports 100bTx */
#define RGEPHY_ANAR_10_FD 0x0040 /* local device supports 10bT FD */
#define RGEPHY_ANAR_10 0x0020 /* local device supports 10bT */
#define RGEPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */
#define RGEPHY_MII_ANLPAR 0x05
#define RGEPHY_ANLPAR_NP 0x8000 /* Next page */
#define RGEPHY_ANLPAR_RF 0x2000 /* Remote fault */
#define RGEPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */
#define RGEPHY_ANLPAR_PC 0x0400 /* Pause capable */
#define RGEPHY_ANLPAR_T4 0x0200 /* link partner supports 100bT4 */
#define RGEPHY_ANLPAR_TX_FD 0x0100 /* link partner supports 100bTx FD */
#define RGEPHY_ANLPAR_TX 0x0080 /* link partner supports 100bTx */
#define RGEPHY_ANLPAR_10_FD 0x0040 /* link partner supports 10bT FD */
#define RGEPHY_ANLPAR_10 0x0020 /* link partner supports 10bT */
#define RGEPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */
#define RGEPHY_SEL_TYPE 0x0001 /* ethernet */
#define RGEPHY_MII_ANER 0x06
#define RGEPHY_ANER_PDF 0x0010 /* Parallel detection fault */
#define RGEPHY_ANER_LPNP 0x0008 /* Link partner can next page */
#define RGEPHY_ANER_NP 0x0004 /* Local PHY can next page */
#define RGEPHY_ANER_RX 0x0002 /* Next page received */
#define RGEPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */
#define RGEPHY_MII_NEXTP 0x07 /* Next page */
#define RGEPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */
#define RGEPHY_MII_1000CTL 0x09 /* 1000baseT control */
#define RGEPHY_1000CTL_TST 0xE000 /* test modes */
#define RGEPHY_1000CTL_MSE 0x1000 /* Master/Slave manual enable */
#define RGEPHY_1000CTL_MSC 0x0800 /* Master/Slave select */
#define RGEPHY_1000CTL_RD 0x0400 /* Repeater/DTE */
#define RGEPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */
#define RGEPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */
#define RGEPHY_TEST_TX_JITTER 0x2000
#define RGEPHY_TEST_TX_JITTER_MASTER_MODE 0x4000
#define RGEPHY_TEST_TX_JITTER_SLAVE_MODE 0x6000
#define RGEPHY_TEST_TX_DISTORTION 0x8000
#define RGEPHY_MII_1000STS 0x0A /* 1000baseT status */
#define RGEPHY_1000STS_MSF 0x8000 /* Master/slave fault */
#define RGEPHY_1000STS_MSR 0x4000 /* Master/slave result */
#define RGEPHY_1000STS_LRS 0x2000 /* Local receiver status */
#define RGEPHY_1000STS_RRS 0x1000 /* Remote receiver status */
#define RGEPHY_1000STS_LPFD 0x0800 /* Link partner can FD */
#define RGEPHY_1000STS_LPHD 0x0400 /* Link partner can HD */
#define RGEPHY_1000STS_IEC 0x00FF /* Idle error count */
#define RGEPHY_MII_EXTSTS 0x0F /* Extended status */
#define RGEPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */
#define RGEPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */
#define RGEPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */
#define RGEPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */
/* RTL8211B(L)/RTL8211C(L) */
#define RGEPHY_MII_PCR 0x10 /* PHY Specific control register */
#define RGEPHY_PCR_ASSERT_CRS 0x0800
#define RGEPHY_PCR_FORCE_LINK 0x0400
#define RGEPHY_PCR_MDI_MASK 0x0060
#define RGEPHY_PCR_MDIX_AUTO 0x0040
#define RGEPHY_PCR_MDIX_MANUAL 0x0020
#define RGEPHY_PCR_MDI_MANUAL 0x0000
#define RGEPHY_PCR_CLK125_DIS 0x0010
#define RGEPHY_PCR_JABBER_DIS 0x0001
/* RTL8211B(L)/RTL8211C(L) */
#define RGEPHY_MII_SSR 0x11 /* PHY Specific status register */
#define RGEPHY_SSR_S1000 0x8000 /* 1000Mbps */
#define RGEPHY_SSR_S100 0x4000 /* 100Mbps */
#define RGEPHY_SSR_S10 0x0000 /* 10Mbps */
#define RGEPHY_SSR_SPD_MASK 0xc000
#define RGEPHY_SSR_FDX 0x2000 /* full duplex */
#define RGEPHY_SSR_PAGE_RECEIVED 0x1000 /* new page received */
#define RGEPHY_SSR_SPD_DPLX_RESOLVED 0x0800 /* speed/duplex resolved */
#define RGEPHY_SSR_LINK 0x0400 /* link up */
#define RGEPHY_SSR_MDI_XOVER 0x0040 /* MDI crossover */
#define RGEPHY_SSR_ALDPS 0x0008 /* RTL8211C(L) only */
#define RGEPHY_SSR_JABBER 0x0001 /* Jabber */
/* RTL8211F */
#define RGEPHY_F_MII_PCR1 0x18 /* PHY Specific control register 1 */
#define RGEPHY_F_PCR1_MDI_MM 0x0200 /* MDI / MDIX Manual Mode */
#define RGEPHY_F_PCR1_MDI_MODE 0x0100 /* MDI Mode (0=MDIX,1=MDI) */
#define RGEPHY_F_PCR1_ALDPS_EN 0x0004 /* Link Down Power Saving Enable */
/* RTL8211F */
#define RGEPHY_F_MII_SSR 0x1A /* PHY Specific status register */
#define RGEPHY_F_SSR_S1000 0x0020 /* 1000Mbps */
#define RGEPHY_F_SSR_S100 0x0010 /* 100Mbps */
#define RGEPHY_F_SSR_S10 0x0000 /* 10Mbps */
#define RGEPHY_F_SSR_SPD_MASK 0x0030
#define RGEPHY_F_SSR_FDX 0x0008 /* full duplex */
#define RGEPHY_F_SSR_LINK 0x0004 /* link up */
#define RGEPHY_F_SSR_MDI 0x0002 /* MDI/MDIX */
#define RGEPHY_F_SSR_JABBER 0x0001 /* Jabber */
/* RTL8211F */
#define RGEPHY_F_EPAGSR 0x1F /* Extension page select register */
/* RTL8211F */
#define RGEPHY_F_MMD_DEV_7 0x07
/* RTL8211F MMD device 7 */
#define RGEPHY_F_MMD_EEEAR 0x3C /* EEE advertisement */
#define EEEAR_1000T 0x0004 /* adv. 1000baseT EEE */
#define EEEAR_100TX 0x0002 /* adv. 100baseTX EEE */
/* RTL8211F MMD device 7 */
#define RGEPHY_F_MMD_EEELPAR 0x3D /* EEE link partner abilities */
#define EEELPAR_1000T 0x0004 /* link partner 1000baseT EEE capable */
#define EEELPAR_100TX 0x0002 /* link partner 100baseTX EEE capable */
/* RTL8153 */
#define URE_GMEDIASTAT 0xe908 /* media status register */
#endif /* _DEV_RGEPHY_MIIREG_H_ */
|
