diff options
Diffstat (limited to 'bsps/m68k/mcf52235/start/cfinit.c')
| -rw-r--r-- | bsps/m68k/mcf52235/start/cfinit.c | 554 |
1 files changed, 554 insertions, 0 deletions
diff --git a/bsps/m68k/mcf52235/start/cfinit.c b/bsps/m68k/mcf52235/start/cfinit.c new file mode 100644 index 0000000000..0007f9a449 --- /dev/null +++ b/bsps/m68k/mcf52235/start/cfinit.c @@ -0,0 +1,554 @@ +/********************************************************************* +* Initialisation Code for ColdFire MCF52235 Processor * +********************************************************************** + Generated by ColdFire Initialisation Utility 2.10.8 + Fri May 23 14:39:00 2008 + + MicroAPL Ltd makes no warranties in respect of the suitability + of this code for any particular purpose, and accepts + no liability for any loss arising out of its use. The person or + persons making use of this file must make the final evaluation + as to its suitability and correctness for a particular application. + +*/ + +/* Processor/internal bus clocked at 60.00 MHz */ + +#include <bsp.h> + +/* Additional register read/write macros (missing in headers) */ +#define MCF_CIM_CCON (*(vuint16*)(void*)(&__IPSBAR[0x00110004])) + +/* Bit definitions and macros for MCF_CIM_CCON */ +#define MCF_CIM_CCON_SZEN (0x00000040) +#define MCF_CIM_CCON_PSTEN (0x00000020) +#define MCF_CIM_CCON_BME (0x00000008) +#define MCF_CIM_CCON_BMT(x) (((x)&0x00000007)<<0) + +/* Function prototypes */ +void init_main(void); +static void disable_interrupts(void); +static void disable_watchdog_timer(void); +static void init_ipsbar(void); +static void init_clock_config(void); +static void init_sram(void); +static void init_flash_controller(void); +static void init_eport(void); +static void init_flexcan(void); +static void init_bus_config(void); +static void init_power_management(void); +static void init_dma_timers(void); +static void init_gp_timer(void); +static void init_interrupt_timers(void); +static void init_real_time_clock(void); +static void init_watchdog_timer(void); +static void init_pin_assignments(void); +static void init_interrupt_controller(void); + +/********************************************************************* +* init_main - Main entry point for initialisation code * +**********************************************************************/ +void init_main(void) +{ + /* Mask all interrupts */ + __asm__ ("move.w #0x2700,%sr"); + + /* Initialise base address of peripherals, VBR, etc */ + init_ipsbar(); + init_clock_config(); + + /* Disable interrupts and watchdog timer */ + disable_interrupts(); + disable_watchdog_timer(); + + /* Initialise individual modules */ + init_sram(); + init_flash_controller(); + init_eport(); + init_flexcan(); + init_bus_config(); + init_power_management(); + init_dma_timers(); + init_gp_timer(); + init_interrupt_timers(); + init_real_time_clock(); + init_watchdog_timer(); + init_pin_assignments(); + + /* Initialise interrupt controller */ + init_interrupt_controller(); +} + +/********************************************************************* +* disable_interrupts - Disable all interrupt sources * +**********************************************************************/ +static void disable_interrupts(void) +{ + vuint8 *p; + int i; + + /* Set ICR008-ICR063 to 0x0 */ + p = (vuint8 *) & MCF_INTC0_ICR8; + for (i = 8; i <= 63; i++) + *p++ = 0x0; + + /* Set ICR108-ICR139 to 0x0 */ + p = (vuint8 *) & MCF_INTC1_ICR8; + for (i = 108; i <= 139; i++) + *p++ = 0x0; +} + +/********************************************************************* +* disable_watchdog_timer - Disable system watchdog timer * +**********************************************************************/ +static void disable_watchdog_timer(void) +{ + /* Disable Core Watchdog Timer */ + MCF_SCM_CWCR = 0; +} + +/********************************************************************* +* init_clock_config - Clock Module * +**********************************************************************/ +static void init_clock_config(void) +{ + /* Clock source is 25.0000 MHz external crystal + Clock mode: Normal PLL mode + Processor/Bus clock frequency = 60.00 MHz + Loss of clock detection disabled + Reset on loss of lock disabled + */ + + /* Divide 25.0000 MHz clock to get 5.00 MHz PLL input clock */ + MCF_CLOCK_CCHR = MCF_CLOCK_CCHR_PFD(0x4); + + /* Set RFD+1 to avoid frequency overshoot and wait for PLL to lock */ + MCF_CLOCK_SYNCR = 0x4103; + while ((MCF_CLOCK_SYNSR & 0x08) == 0) ; + + /* Set desired RFD=0 and MFD=4 and wait for PLL to lock */ + MCF_CLOCK_SYNCR = 0x4003; + while ((MCF_CLOCK_SYNSR & 0x08) == 0) ; + MCF_CLOCK_SYNCR = 0x4007; /* Switch to using PLL */ +} + +/********************************************************************* +* init_ipsbar - Internal Peripheral System Base Address (IPSBAR) * +**********************************************************************/ +static void init_ipsbar(void) +{ + /* Base address of internal peripherals (IPSBAR) = 0x40000000 + + Note: Processor powers up with IPS base address = 0x40000000 + Write to IPS base + 0x00000000 to set new value + */ + *(vuint32 *) 0x40000000 = (vuint32) __IPSBAR + 1; /* +1 for Enable */ +} + +/********************************************************************* +* init_flash_controller - Flash Module * +**********************************************************************/ +static void init_flash_controller(void) +{ + /* Internal Flash module enabled, address = $00000000 + Flash state machine clock = 197.37 kHz + All access types except CPU space/interrupt acknowledge cycle allowed + Flash is Write-Protected + All interrupts disabled + */ + MCF_CFM_CFMCLKD = MCF_CFM_CFMCLKD_PRDIV8 | MCF_CFM_CFMCLKD_DIV(0x12); + MCF_CFM_CFMMCR = 0; + + /* WARNING: Setting FLASHBAR[6]=1 in order to turn off address speculation + This is a workaround for a hardware problem whereby a speculative + access to the Flash occuring at the same time as an SRAM access + can return corrupt data. + + This workaround can result in a 4% - 9% performance penalty. Other workarounds + are possible for certain applications. + + For example, if you know that you will not be using the top 32 KB of the Flash + you can place the SRAM base address at 0x20038000 + + See Device Errata for further details + */ + __asm__ ("move.l #0x00000161,%d0"); + __asm__ ("movec %d0,%FLASHBAR"); +} + +/********************************************************************* +* init_eport - Edge Port Module (EPORT) * +**********************************************************************/ +static void init_eport(void) +{ + /* Pins 1-15 configured as GPIO inputs */ + MCF_EPORT_EPDDR0 = 0; + MCF_EPORT_EPDDR1 = 0; + MCF_EPORT_EPPAR0 = 0; + MCF_EPORT_EPPAR1 = 0; + MCF_EPORT_EPIER0 = 0; + MCF_EPORT_EPIER1 = 0; +} + +/********************************************************************* +* init_flexcan - FlexCAN Module * +**********************************************************************/ +static void init_flexcan(void) +{ + /* FlexCAN controller disabled (CANMCR0[MDIS]=1) */ + MCF_CAN_IMASK = 0; + MCF_CAN_RXGMASK = MCF_CAN_RXGMASK_MI(0x1fffffff); + MCF_CAN_RX14MASK = MCF_CAN_RX14MASK_MI(0x1fffffff); + MCF_CAN_RX15MASK = MCF_CAN_RX15MASK_MI(0x1fffffff); + MCF_CAN_CANCTRL = 0; + MCF_CAN_CANMCR = MCF_CAN_CANMCR_MDIS | + MCF_CAN_CANMCR_FRZ | + MCF_CAN_CANMCR_HALT | MCF_CAN_CANMCR_SUPV | MCF_CAN_CANMCR_MAXMB(0xf); +} + +/********************************************************************* +* init_bus_config - Internal Bus Arbitration * +**********************************************************************/ +static void init_bus_config(void) +{ + /* Use round robin arbitration scheme + Assigned priorities (highest first): + Ethernet + DMA Controller + ColdFire Core + DMA bandwidth control disabled + Park on last active bus master + */ + MCF_SCM_MPARK = MCF_SCM_MPARK_M3PRTY(0x3) | + MCF_SCM_MPARK_M2PRTY(0x2) | (0x1 << 16); +} + +/********************************************************************* +* init_sram - On-chip SRAM * +**********************************************************************/ +static void init_sram(void) +{ + /* Internal SRAM module enabled, address = $20000000 + DMA access to SRAM block disabled + All access types (supervisor and user) allowed + */ + __asm__ ("move.l #0x20000001,%d0"); + __asm__ ("movec %d0,%RAMBAR"); +} + +/********************************************************************* +* init_power_management - Power Management * +**********************************************************************/ +static void init_power_management(void) +{ + /* On executing STOP instruction, processor enters RUN mode + Mode is exited when an interrupt of level 1 or higher is received + */ + MCF_PMM_LPICR = MCF_PMM_LPICR_ENBSTOP; + MCF_PMM_LPCR = MCF_PMM_LPCR_LPMD_RUN; +} + +/********************************************************************* +* init_dma_timers - DMA Timer Modules * +**********************************************************************/ +static void init_dma_timers(void) +{ + /* DMA Timer 0 disabled (DTMR0[RST] = 0) */ + MCF_DTIM0_DTMR = MCF_DTIM_DTMR_CLK(0x1); + MCF_DTIM0_DTXMR = 0; + MCF_DTIM0_DTRR = MCF_DTIM_DTRR_REF(0xffffffff); + + /* DMA Timer 1 disabled (DTMR1[RST] = 0) */ + MCF_DTIM1_DTMR = 0; + MCF_DTIM1_DTXMR = 0; + MCF_DTIM1_DTRR = MCF_DTIM_DTRR_REF(0xffffffff); + + /* DMA Timer 2 disabled (DTMR2[RST] = 0) */ + MCF_DTIM2_DTMR = 0; + MCF_DTIM2_DTXMR = 0; + MCF_DTIM2_DTRR = MCF_DTIM_DTRR_REF(0xffffffff); + + /* DMA Timer 3 disabled (DTMR3[RST] = 0) */ + MCF_DTIM3_DTMR = MCF_DTIM_DTMR_CLK(0x1); + MCF_DTIM3_DTXMR = 0; + MCF_DTIM3_DTRR = MCF_DTIM_DTRR_REF(0xffffffff); +} + +/********************************************************************* +* init_gp_timer - General Purpose Timer (GPT) Module * +**********************************************************************/ +static void init_gp_timer(void) +{ + /* + GPT disabled (GPTASCR1[GPTEN] = 0) + Channel 0 configured as GPIO input + Channel 1 configured as GPIO input + Channel 2 configured as GPIO input + Channel 3 configured as GPIO input + */ + MCF_GPT_GPTSCR1 = 0; + MCF_GPT_GPTDDR = 0; +} + +/********************************************************************** +* init_interrupt_timers - Programmable Interrupt Timer (PIT) Modules * +***********************************************************************/ +static void init_interrupt_timers(void) +{ + /* PIT0 disabled (PCSR0[EN]=0) */ + MCF_PIT0_PCSR = 0; + + /* PIT1 disabled (PCSR1[EN]=0) */ + MCF_PIT1_PCSR = 0; +} + +/********************************************************************* +* init_real_time_clock - Real-Time Clock (RTC) * +**********************************************************************/ +static void init_real_time_clock(void) +{ + /* Disable the RTC */ + MCF_RTC_CR = 0; +} + +/********************************************************************* +* init_watchdog_timer - Watchdog Timer * +**********************************************************************/ +static void init_watchdog_timer(void) +{ + /* Core Watchdog Timer disabled (CWCR[CWE]=0) */ + MCF_SCM_CWCR = 0; +} + +/********************************************************************* +* init_interrupt_controller - Interrupt Controller * +**********************************************************************/ +static void init_interrupt_controller(void) +{ + /* Configured interrupt sources in order of priority... + Level 7: External interrupt /IRQ7, (initially masked) + Level 6: External interrupt /IRQ6, (initially masked) + Level 5: External interrupt /IRQ5, (initially masked) + Level 4: External interrupt /IRQ4, (initially masked) + Level 3: External interrupt /IRQ3, (initially masked) + Level 2: External interrupt /IRQ2, (initially masked) + Level 1: External interrupt /IRQ1, (initially masked) + */ + MCF_INTC0_ICR1 = 0; + MCF_INTC0_ICR2 = 0; + MCF_INTC0_ICR3 = 0; + MCF_INTC0_ICR4 = 0; + MCF_INTC0_ICR5 = 0; + MCF_INTC0_ICR6 = 0; + MCF_INTC0_ICR7 = 0; + MCF_INTC0_ICR8 = 0; + MCF_INTC0_ICR9 = 0; + MCF_INTC0_ICR10 = 0; + MCF_INTC0_ICR11 = 0; + MCF_INTC0_ICR12 = 0; + MCF_INTC0_ICR13 = 0; + MCF_INTC0_ICR14 = 0; + MCF_INTC0_ICR15 = 0; + MCF_INTC0_ICR17 = 0; + MCF_INTC0_ICR18 = 0; + MCF_INTC0_ICR19 = 0; + MCF_INTC0_ICR20 = 0; + MCF_INTC0_ICR21 = 0; + MCF_INTC0_ICR22 = 0; + MCF_INTC0_ICR23 = 0; + MCF_INTC0_ICR24 = 0; + MCF_INTC0_ICR25 = 0; + MCF_INTC0_ICR26 = 0; + MCF_INTC0_ICR27 = 0; + MCF_INTC0_ICR28 = 0; + MCF_INTC0_ICR29 = 0; + MCF_INTC0_ICR30 = 0; + MCF_INTC0_ICR31 = 0; + MCF_INTC0_ICR32 = 0; + MCF_INTC0_ICR33 = 0; + MCF_INTC0_ICR34 = 0; + MCF_INTC0_ICR35 = 0; + MCF_INTC0_ICR36 = 0; + MCF_INTC0_ICR41 = 0; + MCF_INTC0_ICR42 = 0; + MCF_INTC0_ICR43 = 0; + MCF_INTC0_ICR44 = 0; + MCF_INTC0_ICR45 = 0; + MCF_INTC0_ICR46 = 0; + MCF_INTC0_ICR47 = 0; + MCF_INTC0_ICR48 = 0; + MCF_INTC0_ICR49 = 0; + MCF_INTC0_ICR50 = 0; + MCF_INTC0_ICR51 = 0; + MCF_INTC0_ICR52 = 0; + MCF_INTC0_ICR53 = 0; + MCF_INTC0_ICR55 = 0; + MCF_INTC0_ICR56 = 0; + MCF_INTC0_ICR59 = 0; + MCF_INTC0_ICR60 = 0; + MCF_INTC0_ICR61 = 0; + MCF_INTC0_ICR62 = 0; + MCF_INTC0_ICR63 = 0; + MCF_INTC1_ICR8 = 0; + MCF_INTC1_ICR9 = 0; + MCF_INTC1_ICR10 = 0; + MCF_INTC1_ICR11 = 0; + MCF_INTC1_ICR12 = 0; + MCF_INTC1_ICR13 = 0; + MCF_INTC1_ICR14 = 0; + MCF_INTC1_ICR15 = 0; + MCF_INTC1_ICR16 = 0; + MCF_INTC1_ICR17 = 0; + MCF_INTC1_ICR18 = 0; + MCF_INTC1_ICR19 = 0; + MCF_INTC1_ICR20 = 0; + MCF_INTC1_ICR21 = 0; + MCF_INTC1_ICR22 = 0; + MCF_INTC1_ICR23 = 0; + MCF_INTC1_ICR24 = 0; + MCF_INTC1_ICR25 = 0; + MCF_INTC1_ICR32 = 0; + MCF_INTC1_ICR33 = 0; + MCF_INTC1_ICR34 = 0; + MCF_INTC1_ICR35 = 0; + MCF_INTC1_ICR36 = 0; + MCF_INTC1_ICR37 = 0; + MCF_INTC1_ICR38 = 0; + MCF_INTC1_ICR39 = 0; + MCF_INTC0_IMRH = 0xffffffff; + MCF_INTC0_IMRL = 0xfffffffe; + MCF_INTC1_IMRH = 0xffffffff; + MCF_INTC1_IMRL = 0xfffffffe; +} + +/********************************************************************* +* init_pin_assignments - Pin Assignment and General Purpose I/O * +**********************************************************************/ +static void init_pin_assignments(void) +{ + /* Pin assignments for port NQ + Pins NQ7-NQ1 : EdgePort GPIO/IRQ + */ + MCF_GPIO_DDRNQ = 0; + MCF_GPIO_PNQPAR = MCF_GPIO_PNQPAR_PNQPAR7(0x1) | + MCF_GPIO_PNQPAR_PNQPAR6(0x1) | + MCF_GPIO_PNQPAR_PNQPAR5(0x1) | + MCF_GPIO_PNQPAR_PNQPAR4(0x1) | + MCF_GPIO_PNQPAR_PNQPAR3(0x1) | + MCF_GPIO_PNQPAR_PNQPAR2(0x1) | MCF_GPIO_PNQPAR_PNQPAR1(0x1); + + /* Pin assignments for port GP + Pins PG7-PG0 : EdgePort GPIO/IRQ + */ + MCF_GPIO_DDRGP = 0; + MCF_GPIO_PGPPAR = MCF_GPIO_PGPPAR_PGPPAR7 | + MCF_GPIO_PGPPAR_PGPPAR6 | + MCF_GPIO_PGPPAR_PGPPAR5 | + MCF_GPIO_PGPPAR_PGPPAR4 | + MCF_GPIO_PGPPAR_PGPPAR3 | + MCF_GPIO_PGPPAR_PGPPAR2 | + MCF_GPIO_PGPPAR_PGPPAR1 | MCF_GPIO_PGPPAR_PGPPAR0; + + /* Pin assignments for port DD + Pin DD7 : DDATA[3] + Pin DD6 : DDATA[2] + Pin DD5 : DDATA[1] + Pin DD4 : DDATA[0] + Pin DD3 : PST[3] + Pin DD2 : PST[2] + Pin DD1 : PST[1] + Pin DD0 : PST[0] + CCON[PSTEN] = 1 to enable PST/DDATA function + */ + MCF_GPIO_DDRDD = 0; + MCF_GPIO_PDDPAR = MCF_GPIO_PDDPAR_PDDPAR7 | + MCF_GPIO_PDDPAR_PDDPAR6 | + MCF_GPIO_PDDPAR_PDDPAR5 | + MCF_GPIO_PDDPAR_PDDPAR4 | + MCF_GPIO_PDDPAR_PDDPAR3 | + MCF_GPIO_PDDPAR_PDDPAR2 | + MCF_GPIO_PDDPAR_PDDPAR1 | MCF_GPIO_PDDPAR_PDDPAR0; + MCF_CIM_CCON = 0x0021; + + /* Pin assignments for port AN + Pins are all GPIO inputs + */ + MCF_GPIO_DDRAN = 0; + MCF_GPIO_PANPAR = 0; + + /* Pin assignments for port AS + Pins are all GPIO inputs + */ + MCF_GPIO_DDRAS = 0; + MCF_GPIO_PASPAR = 0; + + /* Pin assignments for port LD + Pins are all GPIO inputs + */ + MCF_GPIO_DDRLD = 0; + MCF_GPIO_PLDPAR = 0; + + /* Pin assignments for port QS + Pins are all GPIO inputs + */ + MCF_GPIO_DDRQS = 0; + MCF_GPIO_PQSPAR = 0; + + /* Pin assignments for port TA + Pins are all GPIO inputs + */ + MCF_GPIO_DDRTA = 0; + MCF_GPIO_PTAPAR = 0; + + /* Pin assignments for port TC + Pins are all GPIO inputs + */ + MCF_GPIO_DDRTC = 0; + MCF_GPIO_PTCPAR = 0; + + /* Pin assignments for port TD + Pins are all GPIO inputs + */ + MCF_GPIO_DDRTD = 0; + MCF_GPIO_PTDPAR = 0; + + /* Pin assignments for port UA + Pin UA3 : UART 0 clear-to-send, UCTS0 + Pin UA2 : UART 0 request-to-send, URTS0 + Pin UA1 : UART 0 receive data, URXD0 + Pin UA0 : UART 0 transmit data, UTXD0 + */ + MCF_GPIO_DDRUA = 0; + MCF_GPIO_PUAPAR = MCF_GPIO_PUAPAR_PUAPAR3(0x1) | + MCF_GPIO_PUAPAR_PUAPAR2(0x1) | + MCF_GPIO_PUAPAR_PUAPAR1(0x1) | MCF_GPIO_PUAPAR_PUAPAR0(0x1); + + /* Pin assignments for port UB + Pin UB3 : UART 1 clear-to-send, UCTS1 + Pin UB2 : UART 1 request-to-send, URTS1 + Pin UB1 : UART 1 receive data, URXD1 + Pin UB0 : UART 1 transmit data, UTXD1 + */ + MCF_GPIO_DDRUB = 0; + MCF_GPIO_PUBPAR = MCF_GPIO_PUBPAR_PUBPAR3(0x1) | + MCF_GPIO_PUBPAR_PUBPAR2(0x1) | + MCF_GPIO_PUBPAR_PUBPAR1(0x1) | MCF_GPIO_PUBPAR_PUBPAR0(0x1); + + /* Pin assignments for port UC + Pin UC3 : UART 2 clear-to-send, UCTS2 + Pin UC2 : UART 2 request-to-send, URTS2 + Pin UC1 : UART 2 receive data, URXD2 + Pin UC0 : UART 2 transmit data, UTXD2 + */ + MCF_GPIO_DDRUC = 0; + MCF_GPIO_PUCPAR = MCF_GPIO_PUCPAR_PUCPAR3 | + MCF_GPIO_PUCPAR_PUCPAR2 | + MCF_GPIO_PUCPAR_PUCPAR1 | MCF_GPIO_PUCPAR_PUCPAR0; + + /* Configure drive strengths */ + MCF_GPIO_PDSRH = 0; + MCF_GPIO_PDSRL = 0; + + /* Configure Wired-OR register */ + MCF_GPIO_PWOR = 0; +}
\ No newline at end of file |