diff options
Diffstat (limited to 'freebsd/sys/dev/e1000/e1000_ich8lan.h')
-rw-r--r-- | freebsd/sys/dev/e1000/e1000_ich8lan.h | 76 |
1 files changed, 59 insertions, 17 deletions
diff --git a/freebsd/sys/dev/e1000/e1000_ich8lan.h b/freebsd/sys/dev/e1000/e1000_ich8lan.h index bf928981..999e856b 100644 --- a/freebsd/sys/dev/e1000/e1000_ich8lan.h +++ b/freebsd/sys/dev/e1000/e1000_ich8lan.h @@ -1,6 +1,6 @@ /****************************************************************************** - Copyright (c) 2001-2013, Intel Corporation + Copyright (c) 2001-2014, Intel Corporation All rights reserved. Redistribution and use in source and binary forms, with or without @@ -60,21 +60,26 @@ #define ICH_FLASH_SEG_SIZE_8K 8192 #define ICH_FLASH_SEG_SIZE_64K 65536 -#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ +#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */ /* FW established a valid mode */ -#define E1000_ICH_FWSM_FW_VALID 0x00008000 -#define E1000_ICH_FWSM_PCIM2PCI 0x01000000 /* ME PCIm-to-PCI active */ +#define E1000_ICH_FWSM_FW_VALID 0x00008000 +#define E1000_ICH_FWSM_PCIM2PCI 0x01000000 /* ME PCIm-to-PCI active */ #define E1000_ICH_FWSM_PCIM2PCI_COUNT 2000 #define E1000_ICH_MNG_IAMT_MODE 0x2 #define E1000_FWSM_WLOCK_MAC_MASK 0x0380 #define E1000_FWSM_WLOCK_MAC_SHIFT 7 +#define E1000_FWSM_ULP_CFG_DONE 0x00000400 /* Low power cfg done */ /* Shared Receive Address Registers */ #define E1000_SHRAL_PCH_LPT(_i) (0x05408 + ((_i) * 8)) #define E1000_SHRAH_PCH_LPT(_i) (0x0540C + ((_i) * 8)) +#define E1000_H2ME 0x05B50 /* Host to ME */ +#define E1000_H2ME_ULP 0x00000800 /* ULP Indication Bit */ +#define E1000_H2ME_ENFORCE_SETTINGS 0x00001000 /* Enforce Settings */ + #define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ (ID_LED_OFF1_OFF2 << 8) | \ (ID_LED_OFF1_ON2 << 4) | \ @@ -87,8 +92,11 @@ #define E1000_ICH8_LAN_INIT_TIMEOUT 1500 +/* FEXT register bit definition */ +#define E1000_FEXT_PHY_CABLE_DISCONNECTED 0x00000004 + #define E1000_FEXTNVM_SW_CONFIG 1 -#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M */ +#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* different on ICH8M */ #define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK 0x0C000000 #define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC 0x08000000 @@ -98,6 +106,9 @@ #define E1000_FEXTNVM4_BEACON_DURATION_16USEC 0x3 #define E1000_FEXTNVM6_REQ_PLL_CLK 0x00000100 +#define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION 0x00000200 + +#define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020 #define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL @@ -108,8 +119,8 @@ #define PHY_PAGE_SHIFT 5 #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ ((reg) & MAX_PHY_REG_ADDRESS)) -#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ -#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ +#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */ +#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */ #define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 #define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300 @@ -140,19 +151,20 @@ #define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400 #define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004 #define HV_STATS_PAGE 778 -#define HV_SCC_UPPER PHY_REG(HV_STATS_PAGE, 16) /* Single Collision Count */ +/* Half-duplex collision counts */ +#define HV_SCC_UPPER PHY_REG(HV_STATS_PAGE, 16) /* Single Collision */ #define HV_SCC_LOWER PHY_REG(HV_STATS_PAGE, 17) -#define HV_ECOL_UPPER PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. Count */ +#define HV_ECOL_UPPER PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. */ #define HV_ECOL_LOWER PHY_REG(HV_STATS_PAGE, 19) -#define HV_MCC_UPPER PHY_REG(HV_STATS_PAGE, 20) /* Multiple Coll. Count */ +#define HV_MCC_UPPER PHY_REG(HV_STATS_PAGE, 20) /* Multiple Collision */ #define HV_MCC_LOWER PHY_REG(HV_STATS_PAGE, 21) -#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision Count */ +#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision */ #define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24) -#define HV_COLC_UPPER PHY_REG(HV_STATS_PAGE, 25) /* Collision Count */ +#define HV_COLC_UPPER PHY_REG(HV_STATS_PAGE, 25) /* Collision */ #define HV_COLC_LOWER PHY_REG(HV_STATS_PAGE, 26) #define HV_DC_UPPER PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */ #define HV_DC_LOWER PHY_REG(HV_STATS_PAGE, 28) -#define HV_TNCRS_UPPER PHY_REG(HV_STATS_PAGE, 29) /* Transmit with no CRS */ +#define HV_TNCRS_UPPER PHY_REG(HV_STATS_PAGE, 29) /* Tx with no CRS */ #define HV_TNCRS_LOWER PHY_REG(HV_STATS_PAGE, 30) #define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */ @@ -164,6 +176,16 @@ #define CV_SMB_CTRL PHY_REG(769, 23) #define CV_SMB_CTRL_FORCE_SMBUS 0x0001 +/* I218 Ultra Low Power Configuration 1 Register */ +#define I218_ULP_CONFIG1 PHY_REG(779, 16) +#define I218_ULP_CONFIG1_START 0x0001 /* Start auto ULP config */ +#define I218_ULP_CONFIG1_IND 0x0004 /* Pwr up from ULP indication */ +#define I218_ULP_CONFIG1_STICKY_ULP 0x0010 /* Set sticky ULP mode */ +#define I218_ULP_CONFIG1_INBAND_EXIT 0x0020 /* Inband on ULP exit */ +#define I218_ULP_CONFIG1_WOL_HOST 0x0040 /* WoL Host on ULP exit */ +#define I218_ULP_CONFIG1_RESET_TO_SMBUS 0x0100 /* Reset to SMBus mode */ +#define I218_ULP_CONFIG1_DISABLE_SMB_PERST 0x1000 /* Disable on PERST# */ + /* SMBus Address Phy Register */ #define HV_SMB_ADDR PHY_REG(768, 26) #define HV_SMB_ADDR_MASK 0x007F @@ -198,15 +220,28 @@ /* PHY Power Management Control */ #define HV_PM_CTRL PHY_REG(770, 17) #define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA 0x100 +#define HV_PM_CTRL_K1_ENABLE 0x4000 #define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in ms */ +/* Inband Control */ +#define I217_INBAND_CTRL PHY_REG(770, 18) +#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_MASK 0x3F00 +#define I217_INBAND_CTRL_LINK_STAT_TX_TIMEOUT_SHIFT 8 + +/* Low Power Idle GPIO Control */ +#define I217_LPI_GPIO_CTRL PHY_REG(772, 18) +#define I217_LPI_GPIO_CTRL_AUTO_EN_LPI 0x0800 + /* PHY Low Power Idle Control */ #define I82579_LPI_CTRL PHY_REG(772, 20) #define I82579_LPI_CTRL_100_ENABLE 0x2000 #define I82579_LPI_CTRL_1000_ENABLE 0x4000 #define I82579_LPI_CTRL_ENABLE_MASK 0x6000 -#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT 0x80 + +/* 82579 DFT Control */ +#define I82579_DFT_CTRL PHY_REG(769, 20) +#define I82579_DFT_CTRL_GATE_PHY_RESET 0x0040 /* Gate PHY Reset on MAC Reset */ /* Extended Management Interface (EMI) Registers */ #define I82579_EMI_ADDR 0x10 @@ -216,16 +251,19 @@ #define I82577_MSE_THRESHOLD 0x0887 /* 82577 Mean Square Error Threshold */ #define I82579_MSE_LINK_DOWN 0x2411 /* MSE count before dropping link */ #define I82579_RX_CONFIG 0x3412 /* Receive configuration */ -#define I82579_EEE_PCS_STATUS 0x182D /* IEEE MMD Register 3.1 >> 8 */ +#define I82579_LPI_PLL_SHUT 0x4412 /* LPI PLL Shut Enable */ +#define I82579_EEE_PCS_STATUS 0x182E /* IEEE MMD Register 3.1 >> 8 */ #define I82579_EEE_CAPABILITY 0x0410 /* IEEE MMD Register 3.20 */ #define I82579_EEE_ADVERTISEMENT 0x040E /* IEEE MMD Register 7.60 */ #define I82579_EEE_LP_ABILITY 0x040F /* IEEE MMD Register 7.61 */ -#define I82579_EEE_100_SUPPORTED (1 << 1) /* 100BaseTx EEE supported */ -#define I82579_EEE_1000_SUPPORTED (1 << 2) /* 1000BaseTx EEE supported */ +#define I82579_EEE_100_SUPPORTED (1 << 1) /* 100BaseTx EEE */ +#define I82579_EEE_1000_SUPPORTED (1 << 2) /* 1000BaseTx EEE */ +#define I82579_LPI_100_PLL_SHUT (1 << 2) /* 100M LPI PLL Shut Enabled */ #define I217_EEE_PCS_STATUS 0x9401 /* IEEE MMD Register 3.1 */ #define I217_EEE_CAPABILITY 0x8000 /* IEEE MMD Register 3.20 */ #define I217_EEE_ADVERTISEMENT 0x8001 /* IEEE MMD Register 7.60 */ #define I217_EEE_LP_ABILITY 0x8002 /* IEEE MMD Register 7.61 */ +#define I217_RX_CONFIG 0xB20C /* Receive configuration */ #define E1000_EEE_RX_LPI_RCVD 0x0400 /* Tx LP idle received */ #define E1000_EEE_TX_LPI_RCVD 0x0800 /* Rx LP idle received */ @@ -274,4 +312,8 @@ s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable); void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw); s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable); s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data); +s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data); +s32 e1000_set_eee_pchlan(struct e1000_hw *hw); +s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx); +s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force); #endif /* _E1000_ICH8LAN_H_ */ |