path: root/bsps/arm/stm32h7/hal/stm32h7xx_hal_dma_ex.c

/**
  ******************************************************************************
  * @file    stm32h7xx_hal_dma_ex.c
  * @author  MCD Application Team
  * @brief   DMA Extension HAL module driver
  *          This file provides firmware functions to manage the following
  *          functionalities of the DMA Extension peripheral:
  *           + Extended features functions
  *
  @verbatim
  ==============================================================================
                        ##### How to use this driver #####
  ==============================================================================
  [..]
  The DMA Extension HAL driver can be used as follows:
   (+) Start a multi buffer transfer using the HAL_DMA_MultiBufferStart() function
       for polling mode or HAL_DMA_MultiBufferStart_IT() for interrupt mode.

   (+) Configure the DMA_MUX Synchronization Block using HAL_DMAEx_ConfigMuxSync function.
   (+) Configure the DMA_MUX Request Generator Block using HAL_DMAEx_ConfigMuxRequestGenerator function.
       Functions HAL_DMAEx_EnableMuxRequestGenerator and HAL_DMAEx_DisableMuxRequestGenerator can then be used
       to respectively enable/disable the request generator.

   (+) To handle the DMAMUX Interrupts, the function  HAL_DMAEx_MUX_IRQHandler should be called from
       the DMAMUX IRQ handler i.e DMAMUX1_OVR_IRQHandler or DMAMUX2_OVR_IRQHandler .
       As only one interrupt line is available for all DMAMUX channels and request generators , HAL_DMA_MUX_IRQHandler should be
       called with, as parameter, the appropriate DMA handle as many as used DMAs in the user project
      (exception done if a given DMA is not using the DMAMUX SYNC block neither a request generator)

     -@-  In Memory-to-Memory transfer mode, Multi (Double) Buffer mode is not allowed.
     -@-  When Multi (Double) Buffer mode is enabled, the transfer is circular by default.
     -@-  In Multi (Double) buffer mode, it is possible to update the base address for
          the AHB memory port on the fly (DMA_SxM0AR or DMA_SxM1AR) when the stream is enabled.
     -@-  Multi (Double) buffer mode is possible with DMA and BDMA instances.

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32h7xx_hal.h"

/** @addtogroup STM32H7xx_HAL_Driver
  * @{
  */

/** @defgroup DMAEx DMAEx
  * @brief DMA Extended HAL module driver
  * @{
  */

#ifdef HAL_DMA_MODULE_ENABLED

/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private Constants ---------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @addtogroup DMAEx_Private_Functions
  * @{
  */

static void DMA_MultiBufferSetConfig(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);

/**
  * @}
  */

/* Exported functions ---------------------------------------------------------*/

/** @addtogroup DMAEx_Exported_Functions
  * @{
  */


/** @addtogroup DMAEx_Exported_Functions_Group1
  *
@verbatim
 ===============================================================================
                #####  Extended features functions  #####
 ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Configure the source, destination address and data length and
          Start MultiBuffer DMA transfer
      (+) Configure the source, destination address and data length and
          Start MultiBuffer DMA transfer with interrupt
      (+) Change on the fly the memory0 or memory1 address.
      (+) Configure the DMA_MUX Synchronization Block using HAL_DMAEx_ConfigMuxSync function.
      (+) Configure the DMA_MUX Request Generator Block using HAL_DMAEx_ConfigMuxRequestGenerator function.
      (+) Functions HAL_DMAEx_EnableMuxRequestGenerator and HAL_DMAEx_DisableMuxRequestGenerator can then be used
          to respectively enable/disable the request generator.
      (+) Handle DMAMUX interrupts using HAL_DMAEx_MUX_IRQHandler : should be called from
          the DMAMUX IRQ handler i.e DMAMUX1_OVR_IRQHandler or DMAMUX2_OVR_IRQHandler

@endverbatim
  * @{
  */


/**
  * @brief  Starts the multi_buffer DMA Transfer.
  * @param  hdma      : pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @param  SrcAddress: The source memory Buffer address
  * @param  DstAddress: The destination memory Buffer address
  * @param  SecondMemAddress: The second memory Buffer address in case of multi buffer Transfer
  * @param  DataLength: The length of data to be transferred from source to destination
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_MultiBufferStart(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t SecondMemAddress, uint32_t DataLength)
{
  HAL_StatusTypeDef status = HAL_OK;
  __IO uint32_t *ifcRegister_Base; /* DMA Stream Interrupt Clear register */

  /* Check the parameters */
  assert_param(IS_DMA_BUFFER_SIZE(DataLength));
  assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance));

  /* Memory-to-memory transfer not supported in double buffering mode */
  if (hdma->Init.Direction == DMA_MEMORY_TO_MEMORY)
  {
    hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED;
    status = HAL_ERROR;
  }
  else
  {
    /* Process Locked */
    __HAL_LOCK(hdma);

    if(HAL_DMA_STATE_READY == hdma->State)
    {
      /* Change DMA peripheral state */
      hdma->State = HAL_DMA_STATE_BUSY;

      /* Initialize the error code */
      hdma->ErrorCode = HAL_DMA_ERROR_NONE;

      if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
      {
        /* Enable the Double buffer mode */
        ((DMA_Stream_TypeDef   *)hdma->Instance)->CR |= DMA_SxCR_DBM;

        /* Configure DMA Stream destination address */
        ((DMA_Stream_TypeDef   *)hdma->Instance)->M1AR = SecondMemAddress;

        /* Calculate the interrupt clear flag register (IFCR) base address  */
        ifcRegister_Base = (uint32_t *)((uint32_t)(hdma->StreamBaseAddress + 8U));

        /* Clear all flags */
        *ifcRegister_Base = 0x3FUL << (hdma->StreamIndex & 0x1FU);
      }
      else /* BDMA instance(s) */
      {
        /* Enable the Double buffer mode */
        ((BDMA_Channel_TypeDef   *)hdma->Instance)->CCR |= (BDMA_CCR_DBM | BDMA_CCR_CIRC);

        /* Configure DMA Stream destination address */
        ((BDMA_Channel_TypeDef   *)hdma->Instance)->CM1AR = SecondMemAddress;

        /* Calculate the interrupt clear flag register (IFCR) base address  */
        ifcRegister_Base = (uint32_t *)((uint32_t)(hdma->StreamBaseAddress + 4U));

        /* Clear all flags */
        *ifcRegister_Base = (BDMA_ISR_GIF0) << (hdma->StreamIndex & 0x1FU);
      }

      if(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance) != 0U) /* No DMAMUX available for BDMA1 */
      {
        /* Configure the source, destination address and the data length */
        DMA_MultiBufferSetConfig(hdma, SrcAddress, DstAddress, DataLength);

        /* Clear the DMAMUX synchro overrun flag */
        hdma->DMAmuxChannelStatus->CFR = hdma->DMAmuxChannelStatusMask;

        if(hdma->DMAmuxRequestGen != 0U)
        {
          /* Clear the DMAMUX request generator overrun flag */
          hdma->DMAmuxRequestGenStatus->RGCFR = hdma->DMAmuxRequestGenStatusMask;
        }
      }

      /* Enable the peripheral */
      __HAL_DMA_ENABLE(hdma);
    }
    else
    {
      /* Set the error code to busy */
      hdma->ErrorCode = HAL_DMA_ERROR_BUSY;

      /* Return error status */
      status = HAL_ERROR;
    }
  }
  return status;
}

/**
  * @brief  Starts the multi_buffer DMA Transfer with interrupt enabled.
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @param  SrcAddress: The source memory Buffer address
  * @param  DstAddress: The destination memory Buffer address
  * @param  SecondMemAddress: The second memory Buffer address in case of multi buffer Transfer
  * @param  DataLength: The length of data to be transferred from source to destination
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_MultiBufferStart_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t SecondMemAddress, uint32_t DataLength)
{
  HAL_StatusTypeDef status = HAL_OK;
  __IO uint32_t *ifcRegister_Base; /* DMA Stream Interrupt Clear register */

  /* Check the parameters */
  assert_param(IS_DMA_BUFFER_SIZE(DataLength));
  assert_param(IS_DMA_ALL_INSTANCE(hdma->Instance));

  /* Memory-to-memory transfer not supported in double buffering mode */
  if(hdma->Init.Direction == DMA_MEMORY_TO_MEMORY)
  {
    hdma->ErrorCode = HAL_DMA_ERROR_NOT_SUPPORTED;
    return HAL_ERROR;
  }

  /* Process locked */
  __HAL_LOCK(hdma);

  if(HAL_DMA_STATE_READY == hdma->State)
  {
    /* Change DMA peripheral state */
    hdma->State = HAL_DMA_STATE_BUSY;

    /* Initialize the error code */
    hdma->ErrorCode = HAL_DMA_ERROR_NONE;

    if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
    {
      /* Enable the Double buffer mode */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->CR |= DMA_SxCR_DBM;

      /* Configure DMA Stream destination address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->M1AR = SecondMemAddress;

      /* Calculate the interrupt clear flag register (IFCR) base address  */
      ifcRegister_Base = (uint32_t *)((uint32_t)(hdma->StreamBaseAddress + 8U));

      /* Clear all flags */
      *ifcRegister_Base = 0x3FUL << (hdma->StreamIndex & 0x1FU);
    }
    else /* BDMA instance(s) */
    {
      /* Enable the Double buffer mode */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CCR |= (BDMA_CCR_DBM | BDMA_CCR_CIRC);

      /* Configure DMA Stream destination address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CM1AR = SecondMemAddress;

      /* Calculate the interrupt clear flag register (IFCR) base address  */
      ifcRegister_Base = (uint32_t *)((uint32_t)(hdma->StreamBaseAddress + 4U));

      /* Clear all flags */
      *ifcRegister_Base = (BDMA_ISR_GIF0) << (hdma->StreamIndex & 0x1FU);
    }

    /* Configure the source, destination address and the data length */
    DMA_MultiBufferSetConfig(hdma, SrcAddress, DstAddress, DataLength);

    if(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance) != 0U) /* No DMAMUX available for BDMA1 */
    {
      /* Clear the DMAMUX synchro overrun flag */
      hdma->DMAmuxChannelStatus->CFR = hdma->DMAmuxChannelStatusMask;

      if(hdma->DMAmuxRequestGen != 0U)
      {
        /* Clear the DMAMUX request generator overrun flag */
        hdma->DMAmuxRequestGenStatus->RGCFR = hdma->DMAmuxRequestGenStatusMask;
      }
    }

    if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
    {
      /* Enable Common interrupts*/
      MODIFY_REG(((DMA_Stream_TypeDef   *)hdma->Instance)->CR, (DMA_IT_TC | DMA_IT_TE | DMA_IT_DME | DMA_IT_HT), (DMA_IT_TC | DMA_IT_TE | DMA_IT_DME));
      ((DMA_Stream_TypeDef   *)hdma->Instance)->FCR |= DMA_IT_FE;

      if((hdma->XferHalfCpltCallback != NULL) || (hdma->XferM1HalfCpltCallback != NULL))
      {
        /*Enable Half Transfer IT if corresponding Callback is set*/
        ((DMA_Stream_TypeDef   *)hdma->Instance)->CR  |= DMA_IT_HT;
      }
    }
    else /* BDMA instance(s) */
    {
      /* Enable Common interrupts*/
      MODIFY_REG(((BDMA_Channel_TypeDef   *)hdma->Instance)->CCR, (BDMA_CCR_TCIE | BDMA_CCR_HTIE | BDMA_CCR_TEIE), (BDMA_CCR_TCIE | BDMA_CCR_TEIE));

      if((hdma->XferHalfCpltCallback != NULL) || (hdma->XferM1HalfCpltCallback != NULL))
      {
        /*Enable Half Transfer IT if corresponding Callback is set*/
        ((BDMA_Channel_TypeDef   *)hdma->Instance)->CCR  |= BDMA_CCR_HTIE;
      }
    }

    if(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance) != 0U) /* No DMAMUX available for BDMA1 */
    {
      /* Check if DMAMUX Synchronization is enabled*/
      if((hdma->DMAmuxChannel->CCR & DMAMUX_CxCR_SE) != 0U)
      {
        /* Enable DMAMUX sync overrun IT*/
        hdma->DMAmuxChannel->CCR |= DMAMUX_CxCR_SOIE;
      }

      if(hdma->DMAmuxRequestGen != 0U)
      {
        /* if using DMAMUX request generator, enable the DMAMUX request generator overrun IT*/
        /* enable the request gen overrun IT*/
        hdma->DMAmuxRequestGen->RGCR |= DMAMUX_RGxCR_OIE;
      }
    }

    /* Enable the peripheral */
    __HAL_DMA_ENABLE(hdma);
  }
  else
  {
    /* Set the error code to busy */
    hdma->ErrorCode = HAL_DMA_ERROR_BUSY;

    /* Return error status */
    status = HAL_ERROR;
  }
  return status;
}

/**
  * @brief  Change the memory0 or memory1 address on the fly.
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @param  Address:    The new address
  * @param  memory:     the memory to be changed, This parameter can be one of
  *                     the following values:
  *                      MEMORY0 /
  *                      MEMORY1
  * @note   The MEMORY0 address can be changed only when the current transfer use
  *         MEMORY1 and the MEMORY1 address can be changed only when the current
  *         transfer use MEMORY0.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_ChangeMemory(DMA_HandleTypeDef *hdma, uint32_t Address, HAL_DMA_MemoryTypeDef memory)
{
  if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
  {
    if(memory == MEMORY0)
    {
      /* change the memory0 address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->M0AR = Address;
    }
    else
    {
      /* change the memory1 address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->M1AR = Address;
    }
  }
  else /* BDMA instance(s) */
  {
    if(memory == MEMORY0)
    {
      /* change the memory0 address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CM0AR = Address;
    }
    else
    {
      /* change the memory1 address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CM1AR = Address;
    }
  }

  return HAL_OK;
}

/**
  * @brief  Configure the DMAMUX synchronization parameters for a given DMA stream (instance).
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @param  pSyncConfig : pointer to HAL_DMA_MuxSyncConfigTypeDef : contains the DMAMUX synchronization parameters
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_ConfigMuxSync(DMA_HandleTypeDef *hdma, HAL_DMA_MuxSyncConfigTypeDef *pSyncConfig)
{
  uint32_t syncSignalID = 0;
  uint32_t syncPolarity = 0;

  /* Check the parameters */
  assert_param(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance));
  assert_param(IS_DMAMUX_SYNC_STATE(pSyncConfig->SyncEnable));
  assert_param(IS_DMAMUX_SYNC_EVENT(pSyncConfig->EventEnable));
  assert_param(IS_DMAMUX_SYNC_REQUEST_NUMBER(pSyncConfig->RequestNumber));

  if(pSyncConfig->SyncEnable == ENABLE)
  {
    assert_param(IS_DMAMUX_SYNC_POLARITY(pSyncConfig->SyncPolarity));

    if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
    {
      assert_param(IS_DMA_DMAMUX_SYNC_SIGNAL_ID(pSyncConfig->SyncSignalID));
    }
    else
    {
      assert_param(IS_BDMA_DMAMUX_SYNC_SIGNAL_ID(pSyncConfig->SyncSignalID));
    }
    syncSignalID = pSyncConfig->SyncSignalID;
    syncPolarity = pSyncConfig->SyncPolarity;
  }

  /*Check if the DMA state is ready */
  if(hdma->State == HAL_DMA_STATE_READY)
  {
    /* Process Locked */
    __HAL_LOCK(hdma);

    /* Disable the synchronization and event generation before applying a new config */
    CLEAR_BIT(hdma->DMAmuxChannel->CCR,(DMAMUX_CxCR_SE | DMAMUX_CxCR_EGE));

    /* Set the new synchronization parameters (and keep the request ID filled during the Init)*/
    MODIFY_REG( hdma->DMAmuxChannel->CCR, \
               (~DMAMUX_CxCR_DMAREQ_ID) , \
               (syncSignalID << DMAMUX_CxCR_SYNC_ID_Pos)       | \
               ((pSyncConfig->RequestNumber - 1U) << DMAMUX_CxCR_NBREQ_Pos) | \
               syncPolarity | ((uint32_t)pSyncConfig->SyncEnable << DMAMUX_CxCR_SE_Pos)    | \
               ((uint32_t)pSyncConfig->EventEnable << DMAMUX_CxCR_EGE_Pos));

      /* Process Locked */
    __HAL_UNLOCK(hdma);

    return HAL_OK;
  }
  else
  {
    /* Set the error code to busy */
    hdma->ErrorCode = HAL_DMA_ERROR_BUSY;

    /* Return error status */
    return HAL_ERROR;
  }
}

/**
  * @brief  Configure the DMAMUX request generator block used by the given DMA stream (instance).
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @param  pRequestGeneratorConfig : pointer to HAL_DMA_MuxRequestGeneratorConfigTypeDef :
  *         contains the request generator parameters.
  *
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_ConfigMuxRequestGenerator (DMA_HandleTypeDef *hdma, HAL_DMA_MuxRequestGeneratorConfigTypeDef *pRequestGeneratorConfig)
{
  HAL_StatusTypeDef status;
  HAL_DMA_StateTypeDef temp_state = hdma->State;

  /* Check the parameters */
  assert_param(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance));

  if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
  {
    assert_param(IS_DMA_DMAMUX_REQUEST_GEN_SIGNAL_ID(pRequestGeneratorConfig->SignalID));
  }
  else
  {
    assert_param(IS_BDMA_DMAMUX_REQUEST_GEN_SIGNAL_ID(pRequestGeneratorConfig->SignalID));
  }


  assert_param(IS_DMAMUX_REQUEST_GEN_POLARITY(pRequestGeneratorConfig->Polarity));
  assert_param(IS_DMAMUX_REQUEST_GEN_REQUEST_NUMBER(pRequestGeneratorConfig->RequestNumber));

  /* check if the DMA state is ready
     and DMA is using a DMAMUX request generator block
  */
  if(hdma->DMAmuxRequestGen == 0U)
  {
    /* Set the error code to busy */
    hdma->ErrorCode = HAL_DMA_ERROR_PARAM;

    /* error status */
    status = HAL_ERROR;
  }
  else if(((hdma->DMAmuxRequestGen->RGCR & DMAMUX_RGxCR_GE) == 0U) && (temp_state == HAL_DMA_STATE_READY))
  {
    /* RequestGenerator must be disable prior to the configuration i.e GE bit is 0 */

    /* Process Locked */
    __HAL_LOCK(hdma);

    /* Set the request generator new parameters */
    hdma->DMAmuxRequestGen->RGCR = pRequestGeneratorConfig->SignalID | \
                                  ((pRequestGeneratorConfig->RequestNumber - 1U) << DMAMUX_RGxCR_GNBREQ_Pos)| \
                                  pRequestGeneratorConfig->Polarity;
    /* Process Locked */
    __HAL_UNLOCK(hdma);

    return HAL_OK;
  }
  else
  {
    /* Set the error code to busy */
    hdma->ErrorCode = HAL_DMA_ERROR_BUSY;

    /* error status */
    status = HAL_ERROR;
  }

  return status;
}

/**
  * @brief  Enable the DMAMUX request generator block used by the given DMA stream (instance).
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_EnableMuxRequestGenerator (DMA_HandleTypeDef *hdma)
{
  /* Check the parameters */
  assert_param(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance));

  /* check if the DMA state is ready
     and DMA is using a DMAMUX request generator block */
  if((hdma->State != HAL_DMA_STATE_RESET) && (hdma->DMAmuxRequestGen != 0U))
  {
    /* Enable the request generator*/
    hdma->DMAmuxRequestGen->RGCR |= DMAMUX_RGxCR_GE;

   return HAL_OK;
 }
 else
 {
   return HAL_ERROR;
 }
}

/**
  * @brief  Disable the DMAMUX request generator block used by the given DMA stream (instance).
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_DMAEx_DisableMuxRequestGenerator (DMA_HandleTypeDef *hdma)
{
  /* Check the parameters */
  assert_param(IS_DMA_DMAMUX_ALL_INSTANCE(hdma->Instance));

  /* check if the DMA state is ready
     and DMA is using a DMAMUX request generator block */
  if((hdma->State != HAL_DMA_STATE_RESET) && (hdma->DMAmuxRequestGen != 0U))
  {
    /* Disable the request generator*/
    hdma->DMAmuxRequestGen->RGCR &= ~DMAMUX_RGxCR_GE;

   return HAL_OK;
 }
 else
 {
   return HAL_ERROR;
 }
}

/**
  * @brief  Handles DMAMUX interrupt request.
  * @param  hdma: pointer to a DMA_HandleTypeDef structure that contains
  *               the configuration information for the specified DMA Stream.
  * @retval None
  */
void HAL_DMAEx_MUX_IRQHandler(DMA_HandleTypeDef *hdma)
{
  /* Check for DMAMUX Synchronization overrun */
  if((hdma->DMAmuxChannelStatus->CSR & hdma->DMAmuxChannelStatusMask) != 0U)
  {
    /* Disable the synchro overrun interrupt */
    hdma->DMAmuxChannel->CCR &= ~DMAMUX_CxCR_SOIE;

    /* Clear the DMAMUX synchro overrun flag */
    hdma->DMAmuxChannelStatus->CFR = hdma->DMAmuxChannelStatusMask;

    /* Update error code */
    hdma->ErrorCode |= HAL_DMA_ERROR_SYNC;

    if(hdma->XferErrorCallback != NULL)
    {
      /* Transfer error callback */
      hdma->XferErrorCallback(hdma);
    }
  }

  if(hdma->DMAmuxRequestGen != 0)
  {
   /* if using a DMAMUX request generator block Check for DMAMUX request generator overrun */
    if((hdma->DMAmuxRequestGenStatus->RGSR & hdma->DMAmuxRequestGenStatusMask) != 0U)
    {
      /* Disable the request gen overrun interrupt */
      hdma->DMAmuxRequestGen->RGCR &= ~DMAMUX_RGxCR_OIE;

      /* Clear the DMAMUX request generator overrun flag */
      hdma->DMAmuxRequestGenStatus->RGCFR = hdma->DMAmuxRequestGenStatusMask;

      /* Update error code */
      hdma->ErrorCode |= HAL_DMA_ERROR_REQGEN;

      if(hdma->XferErrorCallback != NULL)
      {
        /* Transfer error callback */
        hdma->XferErrorCallback(hdma);
      }
    }
  }
}


/**
  * @}
  */

/**
  * @}
  */

/** @addtogroup DMAEx_Private_Functions
  * @{
  */

/**
  * @brief  Set the DMA Transfer parameter.
  * @param  hdma:       pointer to a DMA_HandleTypeDef structure that contains
  *                     the configuration information for the specified DMA Stream.
  * @param  SrcAddress: The source memory Buffer address
  * @param  DstAddress: The destination memory Buffer address
  * @param  DataLength: The length of data to be transferred from source to destination
  * @retval HAL status
  */
static void DMA_MultiBufferSetConfig(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength)
{
  if(IS_DMA_STREAM_INSTANCE(hdma->Instance) != 0U) /* DMA1 or DMA2 instance */
  {
    /* Configure DMA Stream data length */
    ((DMA_Stream_TypeDef   *)hdma->Instance)->NDTR = DataLength;

    /* Peripheral to Memory */
    if((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH)
    {
      /* Configure DMA Stream destination address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->PAR = DstAddress;

      /* Configure DMA Stream source address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->M0AR = SrcAddress;
    }
    /* Memory to Peripheral */
    else
    {
      /* Configure DMA Stream source address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->PAR = SrcAddress;

      /* Configure DMA Stream destination address */
      ((DMA_Stream_TypeDef   *)hdma->Instance)->M0AR = DstAddress;
    }
  }
  else /* BDMA instance(s) */
  {
    /* Configure DMA Stream data length */
    ((BDMA_Channel_TypeDef   *)hdma->Instance)->CNDTR = DataLength;

    /* Peripheral to Memory */
    if((hdma->Init.Direction) == DMA_MEMORY_TO_PERIPH)
    {
      /* Configure DMA Stream destination address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CPAR = DstAddress;

      /* Configure DMA Stream source address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CM0AR = SrcAddress;
    }
    /* Memory to Peripheral */
    else
    {
      /* Configure DMA Stream source address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CPAR = SrcAddress;

      /* Configure DMA Stream destination address */
      ((BDMA_Channel_TypeDef   *)hdma->Instance)->CM0AR = DstAddress;
    }
  }
}

/**
  * @}
  */

#endif /* HAL_DMA_MODULE_ENABLED */
/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/