From 44c8a1777f4a3bd619676c16852cb8764369a8ec Mon Sep 17 00:00:00 2001 From: Sebastian Huber Date: Wed, 4 Mar 2020 12:33:17 +0100 Subject: bsp/stm32h7: Import from STM32CubeMX-5.6.0 Update #3910. --- bsps/arm/stm32h7/hal/stm32h7xx_hal_gpio.c | 560 ++++++++++++++++++++++++++++++ 1 file changed, 560 insertions(+) create mode 100644 bsps/arm/stm32h7/hal/stm32h7xx_hal_gpio.c (limited to 'bsps/arm/stm32h7/hal/stm32h7xx_hal_gpio.c') diff --git a/bsps/arm/stm32h7/hal/stm32h7xx_hal_gpio.c b/bsps/arm/stm32h7/hal/stm32h7xx_hal_gpio.c new file mode 100644 index 0000000000..13dcc40d20 --- /dev/null +++ b/bsps/arm/stm32h7/hal/stm32h7xx_hal_gpio.c @@ -0,0 +1,560 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_gpio.c + * @author MCD Application Team + * @brief GPIO HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the General Purpose Input/Output (GPIO) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + @verbatim + ============================================================================== + ##### GPIO Peripheral features ##### + ============================================================================== + [..] + (+) Each port bit of the general-purpose I/O (GPIO) ports can be individually + configured by software in several modes: + (++) Input mode + (++) Analog mode + (++) Output mode + (++) Alternate function mode + (++) External interrupt/event lines + + (+) During and just after reset, the alternate functions and external interrupt + lines are not active and the I/O ports are configured in input floating mode. + + (+) All GPIO pins have weak internal pull-up and pull-down resistors, which can be + activated or not. + + (+) In Output or Alternate mode, each IO can be configured on open-drain or push-pull + type and the IO speed can be selected depending on the VDD value. + + (+) The microcontroller IO pins are connected to onboard peripherals/modules through a + multiplexer that allows only one peripheral alternate function (AF) connected + to an IO pin at a time. In this way, there can be no conflict between peripherals + sharing the same IO pin. + + (+) All ports have external interrupt/event capability. To use external interrupt + lines, the port must be configured in input mode. All available GPIO pins are + connected to the 16 external interrupt/event lines from EXTI0 to EXTI15. + + The external interrupt/event controller consists of up to 23 edge detectors + (16 lines are connected to GPIO) for generating event/interrupt requests (each + input line can be independently configured to select the type (interrupt or event) + and the corresponding trigger event (rising or falling or both). Each line can + also be masked independently. + + ##### How to use this driver ##### + ============================================================================== + [..] + (#) Enable the GPIO AHB clock using the following function: __HAL_RCC_GPIOx_CLK_ENABLE(). + + (#) Configure the GPIO pin(s) using HAL_GPIO_Init(). + (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure + (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef + structure. + (++) In case of Output or alternate function mode selection: the speed is + configured through "Speed" member from GPIO_InitTypeDef structure. + (++) In alternate mode is selection, the alternate function connected to the IO + is configured through "Alternate" member from GPIO_InitTypeDef structure. + (++) Analog mode is required when a pin is to be used as ADC channel + or DAC output. + (++) In case of external interrupt/event selection the "Mode" member from + GPIO_InitTypeDef structure select the type (interrupt or event) and + the corresponding trigger event (rising or falling or both). + + (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority + mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using + HAL_NVIC_EnableIRQ(). + + (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin(). + + (#) To set/reset the level of a pin configured in output mode use + HAL_GPIO_WritePin()/HAL_GPIO_TogglePin(). + + (#) To lock pin configuration until next reset use HAL_GPIO_LockPin(). + + + (#) During and just after reset, the alternate functions are not + active and the GPIO pins are configured in input floating mode (except JTAG + pins). + + (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose + (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has + priority over the GPIO function. + + (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as + general purpose PH0 and PH1, respectively, when the HSE oscillator is off. + The HSE has priority over the GPIO function. + + @endverbatim + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32h7xx_hal.h" + +/** @addtogroup STM32H7xx_HAL_Driver + * @{ + */ + +/** @defgroup GPIO GPIO + * @brief GPIO HAL module driver + * @{ + */ + +#ifdef HAL_GPIO_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private defines ------------------------------------------------------------*/ +/** @addtogroup GPIO_Private_Constants GPIO Private Constants + * @{ + */ +#define GPIO_MODE (0x00000003U) +#define ANALOG_MODE (0x00000008U) +#define EXTI_MODE (0x10000000U) +#define GPIO_MODE_IT (0x00010000U) +#define GPIO_MODE_EVT (0x00020000U) +#define RISING_EDGE (0x00100000U) +#define FALLING_EDGE (0x00200000U) +#define GPIO_OUTPUT_TYPE (0x00000010U) + +#if defined(DUAL_CORE) +#define EXTI_CPU1 (0x01000000U) +#define EXTI_CPU2 (0x02000000U) +#endif /*DUAL_CORE*/ +#define GPIO_NUMBER (16U) +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ +/** @defgroup GPIO_Exported_Functions GPIO Exported Functions + * @{ + */ + +/** @defgroup GPIO_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provides functions allowing to initialize and de-initialize the GPIOs + to be ready for use. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init. + * @param GPIOx: where x can be (A..K) to select the GPIO peripheral. + * @param GPIO_Init: pointer to a GPIO_InitTypeDef structure that contains + * the configuration information for the specified GPIO peripheral. + * @retval None + */ +void HAL_GPIO_Init(GPIO_TypeDef *GPIOx, GPIO_InitTypeDef *GPIO_Init) +{ + uint32_t position = 0x00U; + uint32_t iocurrent; + uint32_t temp; + EXTI_Core_TypeDef *EXTI_CurrentCPU; + +#if defined(DUAL_CORE) && defined(CORE_CM4) + EXTI_CurrentCPU = EXTI_D2; /* EXTI for CM4 CPU */ +#else + EXTI_CurrentCPU = EXTI_D1; /* EXTI for CM7 CPU */ +#endif + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Init->Pin)); + assert_param(IS_GPIO_MODE(GPIO_Init->Mode)); + assert_param(IS_GPIO_PULL(GPIO_Init->Pull)); + + /* Configure the port pins */ + while (((GPIO_Init->Pin) >> position) != 0x00U) + { + /* Get current io position */ + iocurrent = (GPIO_Init->Pin) & (1UL << position); + + if (iocurrent != 0x00U) + { + /*--------------------- GPIO Mode Configuration ------------------------*/ + /* In case of Output or Alternate function mode selection */ + if ((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) || + (GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD)) + { + /* Check the Speed parameter */ + assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); + /* Configure the IO Speed */ + temp = GPIOx->OSPEEDR; + temp &= ~(GPIO_OSPEEDR_OSPEED0 << (position * 2U)); + temp |= (GPIO_Init->Speed << (position * 2U)); + GPIOx->OSPEEDR = temp; + + /* Configure the IO Output Type */ + temp = GPIOx->OTYPER; + temp &= ~(GPIO_OTYPER_OT0 << position) ; + temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4U) << position); + GPIOx->OTYPER = temp; + } + + /* Activate the Pull-up or Pull down resistor for the current IO */ + temp = GPIOx->PUPDR; + temp &= ~(GPIO_PUPDR_PUPD0 << (position * 2U)); + temp |= ((GPIO_Init->Pull) << (position * 2U)); + GPIOx->PUPDR = temp; + + /* In case of Alternate function mode selection */ + if ((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD)) + { + /* Check the Alternate function parameters */ + assert_param(IS_GPIO_AF_INSTANCE(GPIOx)); + assert_param(IS_GPIO_AF(GPIO_Init->Alternate)); + + /* Configure Alternate function mapped with the current IO */ + temp = GPIOx->AFR[position >> 3U]; + temp &= ~(0xFU << ((position & 0x07U) * 4U)); + temp |= ((GPIO_Init->Alternate) << ((position & 0x07U) * 4U)); + GPIOx->AFR[position >> 3U] = temp; + } + + /* Configure IO Direction mode (Input, Output, Alternate or Analog) */ + temp = GPIOx->MODER; + temp &= ~(GPIO_MODER_MODE0 << (position * 2U)); + temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2U)); + GPIOx->MODER = temp; + + /*--------------------- EXTI Mode Configuration ------------------------*/ + /* Configure the External Interrupt or event for the current IO */ + if ((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE) + { + /* Enable SYSCFG Clock */ + __HAL_RCC_SYSCFG_CLK_ENABLE(); + + temp = SYSCFG->EXTICR[position >> 2U]; + temp &= ~(0x0FUL << (4U * (position & 0x03U))); + temp |= (GPIO_GET_INDEX(GPIOx) << (4U * (position & 0x03U))); + SYSCFG->EXTICR[position >> 2U] = temp; + + /* Clear EXTI line configuration */ + temp = EXTI_CurrentCPU->IMR1; + temp &= ~(iocurrent); + if ((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT) + { + temp |= iocurrent; + } + EXTI_CurrentCPU->IMR1 = temp; + + temp = EXTI_CurrentCPU->EMR1; + temp &= ~(iocurrent); + if ((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT) + { + temp |= iocurrent; + } + EXTI_CurrentCPU->EMR1 = temp; + + /* Clear Rising Falling edge configuration */ + temp = EXTI->RTSR1; + temp &= ~(iocurrent); + if ((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE) + { + temp |= iocurrent; + } + EXTI->RTSR1 = temp; + + temp = EXTI->FTSR1; + temp &= ~(iocurrent); + if ((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE) + { + temp |= iocurrent; + } + EXTI->FTSR1 = temp; + } + } + + position++; + } +} + +/** + * @brief De-initializes the GPIOx peripheral registers to their default reset values. + * @param GPIOx: where x can be (A..K) to select the GPIO peripheral. + * @param GPIO_Pin: specifies the port bit to be written. + * This parameter can be one of GPIO_PIN_x where x can be (0..15). + * @retval None + */ +void HAL_GPIO_DeInit(GPIO_TypeDef *GPIOx, uint32_t GPIO_Pin) +{ + uint32_t position = 0x00U; + uint32_t iocurrent; + uint32_t tmp; + EXTI_Core_TypeDef *EXTI_CurrentCPU; + +#if defined(DUAL_CORE) && defined(CORE_CM4) + EXTI_CurrentCPU = EXTI_D2; /* EXTI for CM4 CPU */ +#else + EXTI_CurrentCPU = EXTI_D1; /* EXTI for CM7 CPU */ +#endif + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + /* Configure the port pins */ + while ((GPIO_Pin >> position) != 0x00U) + { + /* Get current io position */ + iocurrent = GPIO_Pin & (1UL << position) ; + + if (iocurrent != 0x00U) + { + /*------------------------- EXTI Mode Configuration --------------------*/ + /* Clear the External Interrupt or Event for the current IO */ + tmp = SYSCFG->EXTICR[position >> 2U]; + tmp &= (0x0FUL << (4U * (position & 0x03U))); + if (tmp == (GPIO_GET_INDEX(GPIOx) << (4U * (position & 0x03U)))) + { + /* Clear EXTI line configuration for Current CPU */ + EXTI_CurrentCPU->IMR1 &= ~(iocurrent); + EXTI_CurrentCPU->EMR1 &= ~(iocurrent); + + /* Clear Rising Falling edge configuration */ + EXTI->RTSR1 &= ~(iocurrent); + EXTI->FTSR1 &= ~(iocurrent); + + tmp = 0x0FUL << (4U * (position & 0x03U)); + SYSCFG->EXTICR[position >> 2U] &= ~tmp; + } + + /*------------------------- GPIO Mode Configuration --------------------*/ + /* Configure IO in Analog Mode */ + GPIOx->MODER |= (GPIO_MODER_MODE0 << (position * 2U)); + + /* Configure the default Alternate Function in current IO */ + GPIOx->AFR[position >> 3U] &= ~(0xFU << ((position & 0x07U) * 4U)) ; + + /* Deactivate the Pull-up and Pull-down resistor for the current IO */ + GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPD0 << (position * 2U)); + + /* Configure the default value IO Output Type */ + GPIOx->OTYPER &= ~(GPIO_OTYPER_OT0 << position) ; + + /* Configure the default value for IO Speed */ + GPIOx->OSPEEDR &= ~(GPIO_OSPEEDR_OSPEED0 << (position * 2U)); + } + + position++; + } +} + +/** + * @} + */ + +/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions + * @brief GPIO Read, Write, Toggle, Lock and EXTI management functions. + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Reads the specified input port pin. + * @param GPIOx: where x can be (A..K) to select the GPIO peripheral. + * @param GPIO_Pin: specifies the port bit to read. + * This parameter can be GPIO_PIN_x where x can be (0..15). + * @retval The input port pin value. + */ +GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin) +{ + GPIO_PinState bitstatus; + + /* Check the parameters */ + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + if ((GPIOx->IDR & GPIO_Pin) != 0x00U) + { + bitstatus = GPIO_PIN_SET; + } + else + { + bitstatus = GPIO_PIN_RESET; + } + return bitstatus; +} + +/** + * @brief Sets or clears the selected data port bit. + * + * @note This function uses GPIOx_BSRR register to allow atomic read/modify + * accesses. In this way, there is no risk of an IRQ occurring between + * the read and the modify access. + * + * @param GPIOx: where x can be (A..K) to select the GPIO peripheral. + * @param GPIO_Pin: specifies the port bit to be written. + * This parameter can be one of GPIO_PIN_x where x can be (0..15). + * @param PinState: specifies the value to be written to the selected bit. + * This parameter can be one of the GPIO_PinState enum values: + * @arg GPIO_PIN_RESET: to clear the port pin + * @arg GPIO_PIN_SET: to set the port pin + * @retval None + */ +void HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState) +{ + /* Check the parameters */ + assert_param(IS_GPIO_PIN(GPIO_Pin)); + assert_param(IS_GPIO_PIN_ACTION(PinState)); + + if (PinState != GPIO_PIN_RESET) + { + GPIOx->BSRR = GPIO_Pin; + } + else + { + GPIOx->BSRR = (uint32_t)GPIO_Pin << GPIO_NUMBER; + } +} + +/** + * @brief Toggles the specified GPIO pins. + * @param GPIOx: Where x can be (A..K) to select the GPIO peripheral. + * @param GPIO_Pin: Specifies the pins to be toggled. + * @retval None + */ +void HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin) +{ + /* Check the parameters */ + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + if ((GPIOx->ODR & GPIO_Pin) == GPIO_Pin) + { + GPIOx->BSRR = (uint32_t)GPIO_Pin << GPIO_NUMBER; + } + else + { + GPIOx->BSRR = GPIO_Pin; + } +} + +/** + * @brief Locks GPIO Pins configuration registers. + * @note The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR, + * GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH. + * @note The configuration of the locked GPIO pins can no longer be modified + * until the next reset. + * @param GPIOx: where x can be (A..K) to select the GPIO peripheral for STM32H7 family + * @param GPIO_Pin: specifies the port bit to be locked. + * This parameter can be any combination of GPIO_PIN_x where x can be (0..15). + * @retval None + */ +HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin) +{ + __IO uint32_t tmp = GPIO_LCKR_LCKK; + + /* Check the parameters */ + assert_param(IS_GPIO_LOCK_INSTANCE(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + /* Apply lock key write sequence */ + tmp |= GPIO_Pin; + /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ + GPIOx->LCKR = tmp; + /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */ + GPIOx->LCKR = GPIO_Pin; + /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ + GPIOx->LCKR = tmp; + /* Read LCKK register. This read is mandatory to complete key lock sequence*/ + tmp = GPIOx->LCKR; + + /* read again in order to confirm lock is active */ + if ((GPIOx->LCKR & GPIO_LCKR_LCKK) != 0x00U) + { + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Handle EXTI interrupt request. + * @param GPIO_Pin: Specifies the port pin connected to corresponding EXTI line. + * @retval None + */ +void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin) +{ +#if defined(DUAL_CORE) && defined(CORE_CM4) + if (__HAL_GPIO_EXTID2_GET_IT(GPIO_Pin) != 0x00U) + { + __HAL_GPIO_EXTID2_CLEAR_IT(GPIO_Pin); + HAL_GPIO_EXTI_Callback(GPIO_Pin); + } +#else + /* EXTI line interrupt detected */ + if (__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != 0x00U) + { + __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin); + HAL_GPIO_EXTI_Callback(GPIO_Pin); + } +#endif +} + +/** + * @brief EXTI line detection callback. + * @param GPIO_Pin: Specifies the port pin connected to corresponding EXTI line. + * @retval None + */ +__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(GPIO_Pin); + + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_GPIO_EXTI_Callback could be implemented in the user file + */ +} + +/** + * @} + */ + + +/** + * @} + */ + +#endif /* HAL_GPIO_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.2.3