diff options
Diffstat (limited to 'bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c')
| -rw-r--r-- | bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c | 2324 |
1 files changed, 2324 insertions, 0 deletions
diff --git a/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c b/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c new file mode 100644 index 0000000000..1dcd77049c --- /dev/null +++ b/bsps/arm/stm32h7/hal/stm32h7xx_hal_tim_ex.c @@ -0,0 +1,2324 @@ +/**
+ ******************************************************************************
+ * @file stm32h7xx_hal_tim_ex.c
+ * @author MCD Application Team
+ * @brief TIM HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Timer Extended peripheral:
+ * + Time Hall Sensor Interface Initialization
+ * + Time Hall Sensor Interface Start
+ * + Time Complementary signal break and dead time configuration
+ * + Time Master and Slave synchronization configuration
+ * + Time Output Compare/PWM Channel Configuration (for channels 5 and 6)
+ * + Timer remapping capabilities configuration
+ @verbatim
+ ==============================================================================
+ ##### TIMER Extended features #####
+ ==============================================================================
+ [..]
+ The Timer Extended features include:
+ (#) Complementary outputs with programmable dead-time for :
+ (++) Output Compare
+ (++) PWM generation (Edge and Center-aligned Mode)
+ (++) One-pulse mode output
+ (#) Synchronization circuit to control the timer with external signals and to
+ interconnect several timers together.
+ (#) Break input to put the timer output signals in reset state or in a known state.
+ (#) Supports incremental (quadrature) encoder and hall-sensor circuitry for
+ positioning purposes
+
+ ##### How to use this driver #####
+ ==============================================================================
+ [..]
+ (#) Initialize the TIM low level resources by implementing the following functions
+ depending on the selected feature:
+ (++) Hall Sensor output : HAL_TIMEx_HallSensor_MspInit()
+
+ (#) Initialize the TIM low level resources :
+ (##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE();
+ (##) TIM pins configuration
+ (+++) Enable the clock for the TIM GPIOs using the following function:
+ __HAL_RCC_GPIOx_CLK_ENABLE();
+ (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init();
+
+ (#) The external Clock can be configured, if needed (the default clock is the
+ internal clock from the APBx), using the following function:
+ HAL_TIM_ConfigClockSource, the clock configuration should be done before
+ any start function.
+
+ (#) Configure the TIM in the desired functioning mode using one of the
+ initialization function of this driver:
+ (++) HAL_TIMEx_HallSensor_Init() and HAL_TIMEx_ConfigCommutEvent(): to use the
+ Timer Hall Sensor Interface and the commutation event with the corresponding
+ Interrupt and DMA request if needed (Note that One Timer is used to interface
+ with the Hall sensor Interface and another Timer should be used to use
+ the commutation event).
+
+ (#) Activate the TIM peripheral using one of the start functions:
+ (++) Complementary Output Compare : HAL_TIMEx_OCN_Start(), HAL_TIMEx_OCN_Start_DMA(), HAL_TIMEx_OC_Start_IT()
+ (++) Complementary PWM generation : HAL_TIMEx_PWMN_Start(), HAL_TIMEx_PWMN_Start_DMA(), HAL_TIMEx_PWMN_Start_IT()
+ (++) Complementary One-pulse mode output : HAL_TIMEx_OnePulseN_Start(), HAL_TIMEx_OnePulseN_Start_IT()
+ (++) Hall Sensor output : HAL_TIMEx_HallSensor_Start(), HAL_TIMEx_HallSensor_Start_DMA(), HAL_TIMEx_HallSensor_Start_IT().
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32h7xx_hal.h"
+
+/** @addtogroup STM32H7xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup TIMEx TIMEx
+ * @brief TIM Extended HAL module driver
+ * @{
+ */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t ChannelNState);
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Functions TIM Extended Exported Functions
+ * @{
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions
+ * @brief Timer Hall Sensor functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Hall Sensor functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Initialize and configure TIM HAL Sensor.
+ (+) De-initialize TIM HAL Sensor.
+ (+) Start the Hall Sensor Interface.
+ (+) Stop the Hall Sensor Interface.
+ (+) Start the Hall Sensor Interface and enable interrupts.
+ (+) Stop the Hall Sensor Interface and disable interrupts.
+ (+) Start the Hall Sensor Interface and enable DMA transfers.
+ (+) Stop the Hall Sensor Interface and disable DMA transfers.
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Initializes the TIM Hall Sensor Interface and initialize the associated handle.
+ * @param htim TIM Hall Sensor Interface handle
+ * @param sConfig TIM Hall Sensor configuration structure
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef *sConfig)
+{
+ TIM_OC_InitTypeDef OC_Config;
+
+ /* Check the TIM handle allocation */
+ if (htim == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode));
+ assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision));
+ assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload));
+ assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity));
+ assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler));
+ assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter));
+
+ if (htim->State == HAL_TIM_STATE_RESET)
+ {
+ /* Allocate lock resource and initialize it */
+ htim->Lock = HAL_UNLOCKED;
+
+#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1)
+ /* Reset interrupt callbacks to legacy week callbacks */
+ TIM_ResetCallback(htim);
+
+ if (htim->HallSensor_MspInitCallback == NULL)
+ {
+ htim->HallSensor_MspInitCallback = HAL_TIMEx_HallSensor_MspInit;
+ }
+ /* Init the low level hardware : GPIO, CLOCK, NVIC */
+ htim->HallSensor_MspInitCallback(htim);
+#else
+ /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */
+ HAL_TIMEx_HallSensor_MspInit(htim);
+#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */
+ }
+
+ /* Set the TIM state */
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Configure the Time base in the Encoder Mode */
+ TIM_Base_SetConfig(htim->Instance, &htim->Init);
+
+ /* Configure the Channel 1 as Input Channel to interface with the three Outputs of the Hall sensor */
+ TIM_TI1_SetConfig(htim->Instance, sConfig->IC1Polarity, TIM_ICSELECTION_TRC, sConfig->IC1Filter);
+
+ /* Reset the IC1PSC Bits */
+ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC;
+ /* Set the IC1PSC value */
+ htim->Instance->CCMR1 |= sConfig->IC1Prescaler;
+
+ /* Enable the Hall sensor interface (XOR function of the three inputs) */
+ htim->Instance->CR2 |= TIM_CR2_TI1S;
+
+ /* Select the TIM_TS_TI1F_ED signal as Input trigger for the TIM */
+ htim->Instance->SMCR &= ~TIM_SMCR_TS;
+ htim->Instance->SMCR |= TIM_TS_TI1F_ED;
+
+ /* Use the TIM_TS_TI1F_ED signal to reset the TIM counter each edge detection */
+ htim->Instance->SMCR &= ~TIM_SMCR_SMS;
+ htim->Instance->SMCR |= TIM_SLAVEMODE_RESET;
+
+ /* Program channel 2 in PWM 2 mode with the desired Commutation_Delay*/
+ OC_Config.OCFastMode = TIM_OCFAST_DISABLE;
+ OC_Config.OCIdleState = TIM_OCIDLESTATE_RESET;
+ OC_Config.OCMode = TIM_OCMODE_PWM2;
+ OC_Config.OCNIdleState = TIM_OCNIDLESTATE_RESET;
+ OC_Config.OCNPolarity = TIM_OCNPOLARITY_HIGH;
+ OC_Config.OCPolarity = TIM_OCPOLARITY_HIGH;
+ OC_Config.Pulse = sConfig->Commutation_Delay;
+
+ TIM_OC2_SetConfig(htim->Instance, &OC_Config);
+
+ /* Select OC2REF as trigger output on TRGO: write the MMS bits in the TIMx_CR2
+ register to 101 */
+ htim->Instance->CR2 &= ~TIM_CR2_MMS;
+ htim->Instance->CR2 |= TIM_TRGO_OC2REF;
+
+ /* Initialize the TIM state*/
+ htim->State = HAL_TIM_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @brief DeInitializes the TIM Hall Sensor interface
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_INSTANCE(htim->Instance));
+
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Disable the TIM Peripheral Clock */
+ __HAL_TIM_DISABLE(htim);
+
+#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1)
+ if (htim->HallSensor_MspDeInitCallback == NULL)
+ {
+ htim->HallSensor_MspDeInitCallback = HAL_TIMEx_HallSensor_MspDeInit;
+ }
+ /* DeInit the low level hardware */
+ htim->HallSensor_MspDeInitCallback(htim);
+#else
+ /* DeInit the low level hardware: GPIO, CLOCK, NVIC */
+ HAL_TIMEx_HallSensor_MspDeInit(htim);
+#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */
+
+ /* Change TIM state */
+ htim->State = HAL_TIM_STATE_RESET;
+
+ /* Release Lock */
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the TIM Hall Sensor MSP.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(htim);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_TIMEx_HallSensor_MspInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief DeInitializes TIM Hall Sensor MSP.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(htim);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_TIMEx_HallSensor_MspDeInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Starts the TIM Hall Sensor Interface.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+
+ /* Enable the Input Capture channel 1
+ (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Hall sensor Interface.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+
+ /* Disable the Input Capture channels 1, 2 and 3
+ (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Hall Sensor Interface in interrupt mode.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+
+ /* Enable the capture compare Interrupts 1 event */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+
+ /* Enable the Input Capture channel 1
+ (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Hall Sensor Interface in interrupt mode.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+
+ /* Disable the Input Capture channel 1
+ (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+ /* Disable the capture compare Interrupts event */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Hall Sensor Interface in DMA mode.
+ * @param htim TIM Hall Sensor Interface handle
+ * @param pData The destination Buffer address.
+ * @param Length The length of data to be transferred from TIM peripheral to memory.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+
+ if (htim->State == HAL_TIM_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+ else if (htim->State == HAL_TIM_STATE_READY)
+ {
+ if (((uint32_t)pData == 0U) && (Length > 0U))
+ {
+ return HAL_ERROR;
+ }
+ else
+ {
+ htim->State = HAL_TIM_STATE_BUSY;
+ }
+ }
+ else
+ {
+ /* nothing to do */
+ }
+ /* Enable the Input Capture channel 1
+ (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE);
+
+ /* Set the DMA Input Capture 1 Callbacks */
+ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt;
+ htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMACaptureHalfCplt;
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream for Capture 1*/
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the capture compare 1 Interrupt */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Hall Sensor Interface in DMA mode.
+ * @param htim TIM Hall Sensor Interface handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_HALL_SENSOR_INTERFACE_INSTANCE(htim->Instance));
+
+ /* Disable the Input Capture channel 1
+ (in the Hall Sensor Interface the three possible channels that can be used are TIM_CHANNEL_1, TIM_CHANNEL_2 and TIM_CHANNEL_3) */
+ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
+
+
+ /* Disable the capture compare Interrupts 1 event */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]);
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions
+ * @brief Timer Complementary Output Compare functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Complementary Output Compare functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Start the Complementary Output Compare/PWM.
+ (+) Stop the Complementary Output Compare/PWM.
+ (+) Start the Complementary Output Compare/PWM and enable interrupts.
+ (+) Stop the Complementary Output Compare/PWM and disable interrupts.
+ (+) Start the Complementary Output Compare/PWM and enable DMA transfers.
+ (+) Stop the Complementary Output Compare/PWM and disable DMA transfers.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Starts the TIM Output Compare signal generation on the complementary
+ * output.
+ * @param htim TIM Output Compare handle
+ * @param Channel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Enable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Output Compare signal generation on the complementary
+ * output.
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Disable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Output Compare signal generation in interrupt mode
+ * on the complementary output.
+ * @param htim TIM OC handle
+ * @param Channel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Enable the TIM Output Compare interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
+ break;
+ }
+
+
+ default:
+ break;
+ }
+
+ /* Enable the TIM Break interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK);
+
+ /* Enable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Output Compare signal generation in interrupt mode
+ * on the complementary output.
+ * @param htim TIM Output Compare handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ uint32_t tmpccer;
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Output Compare interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Disable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the TIM Break interrupt (only if no more channel is active) */
+ tmpccer = htim->Instance->CCER;
+ if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET)
+ {
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK);
+ }
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM Output Compare signal generation in DMA mode
+ * on the complementary output.
+ * @param htim TIM Output Compare handle
+ * @param Channel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @param pData The source Buffer address.
+ * @param Length The length of data to be transferred from memory to TIM peripheral
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ if (htim->State == HAL_TIM_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+ else if (htim->State == HAL_TIM_STATE_READY)
+ {
+ if (((uint32_t)pData == 0U) && (Length > 0U))
+ {
+ return HAL_ERROR;
+ }
+ else
+ {
+ htim->State = HAL_TIM_STATE_BUSY;
+ }
+ }
+ else
+ {
+ /* nothing to do */
+ }
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Set the DMA compare callbacks */
+ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
+ htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream */
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Set the DMA compare callbacks */
+ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
+ htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream */
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Set the DMA compare callbacks */
+ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
+ htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream */
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the TIM Output Compare DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Enable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM Output Compare signal generation in DMA mode
+ * on the complementary output.
+ * @param htim TIM Output Compare handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Output Compare DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Output Compare DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Output Compare DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Disable the Capture compare channel N */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions
+ * @brief Timer Complementary PWM functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Complementary PWM functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Start the Complementary PWM.
+ (+) Stop the Complementary PWM.
+ (+) Start the Complementary PWM and enable interrupts.
+ (+) Stop the Complementary PWM and disable interrupts.
+ (+) Start the Complementary PWM and enable DMA transfers.
+ (+) Stop the Complementary PWM and disable DMA transfers.
+ (+) Start the Complementary Input Capture measurement.
+ (+) Stop the Complementary Input Capture.
+ (+) Start the Complementary Input Capture and enable interrupts.
+ (+) Stop the Complementary Input Capture and disable interrupts.
+ (+) Start the Complementary Input Capture and enable DMA transfers.
+ (+) Stop the Complementary Input Capture and disable DMA transfers.
+ (+) Start the Complementary One Pulse generation.
+ (+) Stop the Complementary One Pulse.
+ (+) Start the Complementary One Pulse and enable interrupts.
+ (+) Stop the Complementary One Pulse and disable interrupts.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Starts the PWM signal generation on the complementary output.
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Enable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the PWM signal generation on the complementary output.
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ /* Disable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the PWM signal generation in interrupt mode on the
+ * complementary output.
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Enable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Enable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Enable the TIM Capture/Compare 3 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Enable the TIM Break interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_BREAK);
+
+ /* Enable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the PWM signal generation in interrupt mode on the
+ * complementary output.
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ uint32_t tmpccer;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Capture/Compare 3 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Disable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the TIM Break interrupt (only if no more channel is active) */
+ tmpccer = htim->Instance->CCER;
+ if ((tmpccer & (TIM_CCER_CC1NE | TIM_CCER_CC2NE | TIM_CCER_CC3NE)) == (uint32_t)RESET)
+ {
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_BREAK);
+ }
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM PWM signal generation in DMA mode on the
+ * complementary output
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @param pData The source Buffer address.
+ * @param Length The length of data to be transferred from memory to TIM peripheral
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length)
+{
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ if (htim->State == HAL_TIM_STATE_BUSY)
+ {
+ return HAL_BUSY;
+ }
+ else if (htim->State == HAL_TIM_STATE_READY)
+ {
+ if (((uint32_t)pData == 0U) && (Length > 0U))
+ {
+ return HAL_ERROR;
+ }
+ else
+ {
+ htim->State = HAL_TIM_STATE_BUSY;
+ }
+ }
+ else
+ {
+ /* nothing to do */
+ }
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Set the DMA compare callbacks */
+ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt;
+ htim->hdma[TIM_DMA_ID_CC1]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream */
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the TIM Capture/Compare 1 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Set the DMA compare callbacks */
+ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt;
+ htim->hdma[TIM_DMA_ID_CC2]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream */
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the TIM Capture/Compare 2 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Set the DMA compare callbacks */
+ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt;
+ htim->hdma[TIM_DMA_ID_CC3]->XferHalfCpltCallback = TIM_DMADelayPulseHalfCplt;
+
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ;
+
+ /* Enable the DMA stream */
+ if (HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3, Length) != HAL_OK)
+ {
+ return HAL_ERROR;
+ }
+ /* Enable the TIM Capture/Compare 3 DMA request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Enable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM PWM signal generation in DMA mode on the complementary
+ * output
+ * @param htim TIM handle
+ * @param Channel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @arg TIM_CHANNEL_3: TIM Channel 3 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, Channel));
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ {
+ /* Disable the TIM Capture/Compare 1 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1);
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC1]);
+ break;
+ }
+
+ case TIM_CHANNEL_2:
+ {
+ /* Disable the TIM Capture/Compare 2 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2);
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC2]);
+ break;
+ }
+
+ case TIM_CHANNEL_3:
+ {
+ /* Disable the TIM Capture/Compare 3 DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3);
+ (void)HAL_DMA_Abort_IT(htim->hdma[TIM_DMA_ID_CC3]);
+ break;
+ }
+
+ default:
+ break;
+ }
+
+ /* Disable the complementary PWM output */
+ TIM_CCxNChannelCmd(htim->Instance, Channel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions
+ * @brief Timer Complementary One Pulse functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Timer Complementary One Pulse functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Start the Complementary One Pulse generation.
+ (+) Stop the Complementary One Pulse.
+ (+) Start the Complementary One Pulse and enable interrupts.
+ (+) Stop the Complementary One Pulse and disable interrupts.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Starts the TIM One Pulse signal generation on the complementary
+ * output.
+ * @param htim TIM One Pulse handle
+ * @param OutputChannel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Enable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM One Pulse signal generation on the complementary
+ * output.
+ * @param htim TIM One Pulse handle
+ * @param OutputChannel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Disable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Starts the TIM One Pulse signal generation in interrupt mode on the
+ * complementary channel.
+ * @param htim TIM One Pulse handle
+ * @param OutputChannel TIM Channel to be enabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Enable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
+
+ /* Enable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2);
+
+ /* Enable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
+
+ /* Enable the Main Output */
+ __HAL_TIM_MOE_ENABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stops the TIM One Pulse signal generation in interrupt mode on the
+ * complementary channel.
+ * @param htim TIM One Pulse handle
+ * @param OutputChannel TIM Channel to be disabled
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1 selected
+ * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
+
+ /* Disable the TIM Capture/Compare 1 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1);
+
+ /* Disable the TIM Capture/Compare 2 interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2);
+
+ /* Disable the complementary One Pulse output */
+ TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_DISABLE);
+
+ /* Disable the Main Output */
+ __HAL_TIM_MOE_DISABLE(htim);
+
+ /* Disable the Peripheral */
+ __HAL_TIM_DISABLE(htim);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
+ * @brief Peripheral Control functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Peripheral Control functions #####
+ ==============================================================================
+ [..]
+ This section provides functions allowing to:
+ (+) Configure the commutation event in case of use of the Hall sensor interface.
+ (+) Configure Output channels for OC and PWM mode.
+
+ (+) Configure Complementary channels, break features and dead time.
+ (+) Configure Master synchronization.
+ (+) Configure timer remapping capabilities.
+ (+) Select timer input source.
+ (+) Enable or disable channel grouping.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configure the TIM commutation event sequence.
+ * @note This function is mandatory to use the commutation event in order to
+ * update the configuration at each commutation detection on the TRGI input of the Timer,
+ * the typical use of this feature is with the use of another Timer(interface Timer)
+ * configured in Hall sensor interface, this interface Timer will generate the
+ * commutation at its TRGO output (connected to Timer used in this function) each time
+ * the TI1 of the Interface Timer detect a commutation at its input TI1.
+ * @param htim TIM handle
+ * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal trigger 0 selected
+ * @arg TIM_TS_ITR1: Internal trigger 1 selected
+ * @arg TIM_TS_ITR2: Internal trigger 2 selected
+ * @arg TIM_TS_ITR3: Internal trigger 3 selected
+ * @arg TIM_TS_ITR12: Internal trigger 12 selected (*)
+ * @arg TIM_TS_ITR13: Internal trigger 13 selected (*)
+ * @arg TIM_TS_NONE: No trigger is needed
+ * @param CommutationSource the Commutation Event source
+ * This parameter can be one of the following values:
+ * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+ * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef *htim, uint32_t InputTrigger,
+ uint32_t CommutationSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+ __HAL_LOCK(htim);
+
+ if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+ (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3) ||
+ (InputTrigger == TIM_TS_ITR12) || (InputTrigger == TIM_TS_ITR13))
+ {
+ /* Select the Input trigger */
+ htim->Instance->SMCR &= ~TIM_SMCR_TS;
+ htim->Instance->SMCR |= InputTrigger;
+ }
+
+ /* Select the Capture Compare preload feature */
+ htim->Instance->CR2 |= TIM_CR2_CCPC;
+ /* Select the Commutation event source */
+ htim->Instance->CR2 &= ~TIM_CR2_CCUS;
+ htim->Instance->CR2 |= CommutationSource;
+
+ /* Disable Commutation Interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_COM);
+
+ /* Disable Commutation DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_COM);
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configure the TIM commutation event sequence with interrupt.
+ * @note This function is mandatory to use the commutation event in order to
+ * update the configuration at each commutation detection on the TRGI input of the Timer,
+ * the typical use of this feature is with the use of another Timer(interface Timer)
+ * configured in Hall sensor interface, this interface Timer will generate the
+ * commutation at its TRGO output (connected to Timer used in this function) each time
+ * the TI1 of the Interface Timer detect a commutation at its input TI1.
+ * @param htim TIM handle
+ * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal trigger 0 selected
+ * @arg TIM_TS_ITR1: Internal trigger 1 selected
+ * @arg TIM_TS_ITR2: Internal trigger 2 selected
+ * @arg TIM_TS_ITR3: Internal trigger 3 selected
+ * @arg TIM_TS_ITR2: Internal trigger 12 selected (*)
+ * @arg TIM_TS_ITR3: Internal trigger 13 selected (*)
+ * @arg TIM_TS_NONE: No trigger is needed
+ * @param CommutationSource the Commutation Event source
+ * This parameter can be one of the following values:
+ * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+ * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef *htim, uint32_t InputTrigger,
+ uint32_t CommutationSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+ __HAL_LOCK(htim);
+
+ if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+ (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3) ||
+ (InputTrigger == TIM_TS_ITR12) || (InputTrigger == TIM_TS_ITR13))
+ {
+ /* Select the Input trigger */
+ htim->Instance->SMCR &= ~TIM_SMCR_TS;
+ htim->Instance->SMCR |= InputTrigger;
+ }
+
+ /* Select the Capture Compare preload feature */
+ htim->Instance->CR2 |= TIM_CR2_CCPC;
+ /* Select the Commutation event source */
+ htim->Instance->CR2 &= ~TIM_CR2_CCUS;
+ htim->Instance->CR2 |= CommutationSource;
+
+ /* Disable Commutation DMA request */
+ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_COM);
+
+ /* Enable the Commutation Interrupt */
+ __HAL_TIM_ENABLE_IT(htim, TIM_IT_COM);
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configure the TIM commutation event sequence with DMA.
+ * @note This function is mandatory to use the commutation event in order to
+ * update the configuration at each commutation detection on the TRGI input of the Timer,
+ * the typical use of this feature is with the use of another Timer(interface Timer)
+ * configured in Hall sensor interface, this interface Timer will generate the
+ * commutation at its TRGO output (connected to Timer used in this function) each time
+ * the TI1 of the Interface Timer detect a commutation at its input TI1.
+ * @note The user should configure the DMA in his own software, in This function only the COMDE bit is set
+ * @param htim TIM handle
+ * @param InputTrigger the Internal trigger corresponding to the Timer Interfacing with the Hall sensor
+ * This parameter can be one of the following values:
+ * @arg TIM_TS_ITR0: Internal trigger 0 selected
+ * @arg TIM_TS_ITR1: Internal trigger 1 selected
+ * @arg TIM_TS_ITR2: Internal trigger 2 selected
+ * @arg TIM_TS_ITR3: Internal trigger 3 selected
+ * @arg TIM_TS_ITR2: Internal trigger 12 selected (*)
+ * @arg TIM_TS_ITR3: Internal trigger 13 selected (*)
+ * @arg TIM_TS_NONE: No trigger is needed
+ *
+ * (*) Value not defined in all devices.
+ *
+ * @param CommutationSource the Commutation Event source
+ * This parameter can be one of the following values:
+ * @arg TIM_COMMUTATION_TRGI: Commutation source is the TRGI of the Interface Timer
+ * @arg TIM_COMMUTATION_SOFTWARE: Commutation source is set by software using the COMG bit
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef *htim, uint32_t InputTrigger,
+ uint32_t CommutationSource)
+{
+ /* Check the parameters */
+ assert_param(IS_TIM_COMMUTATION_EVENT_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_INTERNAL_TRIGGEREVENT_SELECTION(InputTrigger));
+
+ __HAL_LOCK(htim);
+
+ if ((InputTrigger == TIM_TS_ITR0) || (InputTrigger == TIM_TS_ITR1) ||
+ (InputTrigger == TIM_TS_ITR2) || (InputTrigger == TIM_TS_ITR3) ||
+ (InputTrigger == TIM_TS_ITR12) || (InputTrigger == TIM_TS_ITR13))
+ {
+ /* Select the Input trigger */
+ htim->Instance->SMCR &= ~TIM_SMCR_TS;
+ htim->Instance->SMCR |= InputTrigger;
+ }
+
+ /* Select the Capture Compare preload feature */
+ htim->Instance->CR2 |= TIM_CR2_CCPC;
+ /* Select the Commutation event source */
+ htim->Instance->CR2 &= ~TIM_CR2_CCUS;
+ htim->Instance->CR2 |= CommutationSource;
+
+ /* Enable the Commutation DMA Request */
+ /* Set the DMA Commutation Callback */
+ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt;
+ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferHalfCpltCallback = TIMEx_DMACommutationHalfCplt;
+ /* Set the DMA error callback */
+ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError;
+
+ /* Disable Commutation Interrupt */
+ __HAL_TIM_DISABLE_IT(htim, TIM_IT_COM);
+
+ /* Enable the Commutation DMA Request */
+ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_COM);
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configures the TIM in master mode.
+ * @param htim TIM handle.
+ * @param sMasterConfig pointer to a TIM_MasterConfigTypeDef structure that
+ * contains the selected trigger output (TRGO) and the Master/Slave
+ * mode.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
+ TIM_MasterConfigTypeDef *sMasterConfig)
+{
+ uint32_t tmpcr2;
+ uint32_t tmpsmcr;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_MASTER_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_TRGO_SOURCE(sMasterConfig->MasterOutputTrigger));
+ assert_param(IS_TIM_MSM_STATE(sMasterConfig->MasterSlaveMode));
+
+ /* Check input state */
+ __HAL_LOCK(htim);
+
+ /* Change the handler state */
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Get the TIMx CR2 register value */
+ tmpcr2 = htim->Instance->CR2;
+
+ /* Get the TIMx SMCR register value */
+ tmpsmcr = htim->Instance->SMCR;
+
+ /* If the timer supports ADC synchronization through TRGO2, set the master mode selection 2 */
+ if (IS_TIM_TRGO2_INSTANCE(htim->Instance))
+ {
+ /* Check the parameters */
+ assert_param(IS_TIM_TRGO2_SOURCE(sMasterConfig->MasterOutputTrigger2));
+
+ /* Clear the MMS2 bits */
+ tmpcr2 &= ~TIM_CR2_MMS2;
+ /* Select the TRGO2 source*/
+ tmpcr2 |= sMasterConfig->MasterOutputTrigger2;
+ }
+
+ /* Reset the MMS Bits */
+ tmpcr2 &= ~TIM_CR2_MMS;
+ /* Select the TRGO source */
+ tmpcr2 |= sMasterConfig->MasterOutputTrigger;
+
+ /* Update TIMx CR2 */
+ htim->Instance->CR2 = tmpcr2;
+
+ if (IS_TIM_SLAVE_INSTANCE(htim->Instance))
+ {
+ /* Reset the MSM Bit */
+ tmpsmcr &= ~TIM_SMCR_MSM;
+ /* Set master mode */
+ tmpsmcr |= sMasterConfig->MasterSlaveMode;
+
+ /* Update TIMx SMCR */
+ htim->Instance->SMCR = tmpsmcr;
+ }
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Configures the Break feature, dead time, Lock level, OSSI/OSSR State
+ * and the AOE(automatic output enable).
+ * @param htim TIM handle
+ * @param sBreakDeadTimeConfig pointer to a TIM_ConfigBreakDeadConfigTypeDef structure that
+ * contains the BDTR Register configuration information for the TIM peripheral.
+ * @note Interrupts can be generated when an active level is detected on the
+ * break input, the break 2 input or the system break input. Break
+ * interrupt can be enabled by calling the @ref __HAL_TIM_ENABLE_IT macro.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim,
+ TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig)
+{
+ /* Keep this variable initialized to 0 as it is used to configure BDTR register */
+ uint32_t tmpbdtr = 0U;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_OSSR_STATE(sBreakDeadTimeConfig->OffStateRunMode));
+ assert_param(IS_TIM_OSSI_STATE(sBreakDeadTimeConfig->OffStateIDLEMode));
+ assert_param(IS_TIM_LOCK_LEVEL(sBreakDeadTimeConfig->LockLevel));
+ assert_param(IS_TIM_DEADTIME(sBreakDeadTimeConfig->DeadTime));
+ assert_param(IS_TIM_BREAK_STATE(sBreakDeadTimeConfig->BreakState));
+ assert_param(IS_TIM_BREAK_POLARITY(sBreakDeadTimeConfig->BreakPolarity));
+ assert_param(IS_TIM_BREAK_FILTER(sBreakDeadTimeConfig->BreakFilter));
+ assert_param(IS_TIM_AUTOMATIC_OUTPUT_STATE(sBreakDeadTimeConfig->AutomaticOutput));
+
+ /* Check input state */
+ __HAL_LOCK(htim);
+
+ /* Set the Lock level, the Break enable Bit and the Polarity, the OSSR State,
+ the OSSI State, the dead time value and the Automatic Output Enable Bit */
+
+ /* Set the BDTR bits */
+ MODIFY_REG(tmpbdtr, TIM_BDTR_DTG, sBreakDeadTimeConfig->DeadTime);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_LOCK, sBreakDeadTimeConfig->LockLevel);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_OSSI, sBreakDeadTimeConfig->OffStateIDLEMode);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_OSSR, sBreakDeadTimeConfig->OffStateRunMode);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_BKE, sBreakDeadTimeConfig->BreakState);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_BKP, sBreakDeadTimeConfig->BreakPolarity);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_AOE, sBreakDeadTimeConfig->AutomaticOutput);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_BKF, (sBreakDeadTimeConfig->BreakFilter << TIM_BDTR_BKF_Pos));
+
+ if (IS_TIM_BKIN2_INSTANCE(htim->Instance))
+ {
+ /* Check the parameters */
+ assert_param(IS_TIM_BREAK2_STATE(sBreakDeadTimeConfig->Break2State));
+ assert_param(IS_TIM_BREAK2_POLARITY(sBreakDeadTimeConfig->Break2Polarity));
+ assert_param(IS_TIM_BREAK_FILTER(sBreakDeadTimeConfig->Break2Filter));
+
+ /* Set the BREAK2 input related BDTR bits */
+ MODIFY_REG(tmpbdtr, TIM_BDTR_BK2F, (sBreakDeadTimeConfig->Break2Filter << TIM_BDTR_BK2F_Pos));
+ MODIFY_REG(tmpbdtr, TIM_BDTR_BK2E, sBreakDeadTimeConfig->Break2State);
+ MODIFY_REG(tmpbdtr, TIM_BDTR_BK2P, sBreakDeadTimeConfig->Break2Polarity);
+ }
+
+ /* Set TIMx_BDTR */
+ htim->Instance->BDTR = tmpbdtr;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+#if defined(TIM_BREAK_INPUT_SUPPORT)
+
+/**
+ * @brief Configures the break input source.
+ * @param htim TIM handle.
+ * @param BreakInput Break input to configure
+ * This parameter can be one of the following values:
+ * @arg TIM_BREAKINPUT_BRK: Timer break input
+ * @arg TIM_BREAKINPUT_BRK2: Timer break 2 input
+ * @param sBreakInputConfig Break input source configuration
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakInput(TIM_HandleTypeDef *htim,
+ uint32_t BreakInput,
+ TIMEx_BreakInputConfigTypeDef *sBreakInputConfig)
+
+{
+ uint32_t tmporx;
+ uint32_t bkin_enable_mask;
+ uint32_t bkin_polarity_mask;
+ uint32_t bkin_enable_bitpos;
+ uint32_t bkin_polarity_bitpos;
+
+ /* Check the parameters */
+ assert_param(IS_TIM_BREAK_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_BREAKINPUT(BreakInput));
+ assert_param(IS_TIM_BREAKINPUTSOURCE(sBreakInputConfig->Source));
+ assert_param(IS_TIM_BREAKINPUTSOURCE_STATE(sBreakInputConfig->Enable));
+ if (sBreakInputConfig->Source != TIM_BREAKINPUTSOURCE_DFSDM1)
+ {
+ assert_param(IS_TIM_BREAKINPUTSOURCE_POLARITY(sBreakInputConfig->Polarity));
+ }
+
+ /* Check input state */
+ __HAL_LOCK(htim);
+
+ switch (sBreakInputConfig->Source)
+ {
+ case TIM_BREAKINPUTSOURCE_BKIN:
+ {
+ bkin_enable_mask = TIM1_AF1_BKINE;
+ bkin_enable_bitpos = TIM1_AF1_BKINE_Pos;
+ bkin_polarity_mask = TIM1_AF1_BKINP;
+ bkin_polarity_bitpos = TIM1_AF1_BKINP_Pos;
+ break;
+ }
+ case TIM_BREAKINPUTSOURCE_COMP1:
+ {
+ bkin_enable_mask = TIM1_AF1_BKCMP1E;
+ bkin_enable_bitpos = TIM1_AF1_BKCMP1E_Pos;
+ bkin_polarity_mask = TIM1_AF1_BKCMP1P;
+ bkin_polarity_bitpos = TIM1_AF1_BKCMP1P_Pos;
+ break;
+ }
+ case TIM_BREAKINPUTSOURCE_COMP2:
+ {
+ bkin_enable_mask = TIM1_AF1_BKCMP2E;
+ bkin_enable_bitpos = TIM1_AF1_BKCMP2E_Pos;
+ bkin_polarity_mask = TIM1_AF1_BKCMP2P;
+ bkin_polarity_bitpos = TIM1_AF1_BKCMP2P_Pos;
+ break;
+ }
+ case TIM_BREAKINPUTSOURCE_DFSDM1:
+ {
+ bkin_enable_mask = TIM1_AF1_BKDF1BK0E;
+ bkin_enable_bitpos = 8U;
+ bkin_polarity_mask = 0U;
+ bkin_polarity_bitpos = 0U;
+ break;
+ }
+
+ default:
+ {
+ bkin_enable_mask = 0U;
+ bkin_polarity_mask = 0U;
+ bkin_enable_bitpos = 0U;
+ bkin_polarity_bitpos = 0U;
+ break;
+ }
+ }
+
+ switch (BreakInput)
+ {
+ case TIM_BREAKINPUT_BRK:
+ {
+ /* Get the TIMx_AF1 register value */
+ tmporx = htim->Instance->AF1;
+
+ /* Enable the break input */
+ tmporx &= ~bkin_enable_mask;
+ tmporx |= (sBreakInputConfig->Enable << bkin_enable_bitpos) & bkin_enable_mask;
+
+ /* Set the break input polarity */
+ if (sBreakInputConfig->Source != TIM_BREAKINPUTSOURCE_DFSDM1)
+ {
+ tmporx &= ~bkin_polarity_mask;
+ tmporx |= (sBreakInputConfig->Polarity << bkin_polarity_bitpos) & bkin_polarity_mask;
+ }
+
+ /* Set TIMx_AF1 */
+ htim->Instance->AF1 = tmporx;
+ break;
+ }
+ case TIM_BREAKINPUT_BRK2:
+ {
+ /* Get the TIMx_AF2 register value */
+ tmporx = htim->Instance->AF2;
+
+ /* Enable the break input */
+ tmporx &= ~bkin_enable_mask;
+ tmporx |= (sBreakInputConfig->Enable << bkin_enable_bitpos) & bkin_enable_mask;
+
+ /* Set the break input polarity */
+ if (sBreakInputConfig->Source != TIM_BREAKINPUTSOURCE_DFSDM1)
+ {
+ tmporx &= ~bkin_polarity_mask;
+ tmporx |= (sBreakInputConfig->Polarity << bkin_polarity_bitpos) & bkin_polarity_mask;
+ }
+
+ /* Set TIMx_AF2 */
+ htim->Instance->AF2 = tmporx;
+ break;
+ }
+ default:
+ break;
+ }
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+#endif /*TIM_BREAK_INPUT_SUPPORT */
+
+/**
+ * @brief Configures the TIMx Remapping input capabilities.
+ * @param htim TIM handle.
+ * @param Remap specifies the TIM remapping source.
+ * For TIM1, the parameter is one of the following values:
+ * @arg TIM_TIM1_ETR_GPIO: TIM1_ETR is connected to GPIO
+ * @arg TIM_TIM1_ETR_COMP1: TIM1_ETR is connected to COMP1 output
+ * @arg TIM_TIM1_ETR_COMP2: TIM1_ETR is connected to COMP2 output
+ * @arg TIM_TIM1_ETR_ADC1_AWD1: TIM1_ETR is connected to ADC1 AWD1
+ * @arg TIM_TIM1_ETR_ADC1_AWD2: TIM1_ETR is connected to ADC1 AWD2
+ * @arg TIM_TIM1_ETR_ADC1_AWD3: TIM1_ETR is connected to ADC1 AWD3
+ * @arg TIM_TIM1_ETR_ADC3_AWD1: TIM1_ETR is connected to ADC3 AWD1
+ * @arg TIM_TIM1_ETR_ADC3_AWD2: TIM1_ETR is connected to ADC3 AWD2
+ * @arg TIM_TIM1_ETR_ADC3_AWD3: TIM1_ETR is connected to ADC3 AWD3
+ *
+ * For TIM2, the parameter is one of the following values:
+ * @arg TIM_TIM2_ETR_GPIO: TIM2_ETR is connected to GPIO
+ * @arg TIM_TIM2_ETR_COMP1: TIM2_ETR is connected to COMP1 output
+ * @arg TIM_TIM2_ETR_COMP2: TIM2_ETR is connected to COMP2 output
+ * @arg TIM_TIM2_ETR_LSE: TIM2_ETR is connected to LSE
+ * @arg TIM_TIM2_ETR_SAI1_FSA: TIM2_ETR is connected to SAI1 FS_A
+ * @arg TIM_TIM2_ETR_SAI1_FSB: TIM2_ETR is connected to SAI1 FS_B
+ *
+ * For TIM3, the parameter is one of the following values:
+ * @arg TIM_TIM3_ETR_GPIO: TIM3_ETR is connected to GPIO
+ * @arg TIM_TIM3_ETR_COMP1: TIM3_ETR is connected to COMP1 output
+ *
+ * For TIM5, the parameter is one of the following values:
+ * @arg TIM_TIM5_ETR_GPIO: TIM5_ETR is connected to GPIO
+ * @arg TIM_TIM5_ETR_SAI2_FSA: TIM5_ETR is connected to SAI2 FS_A (*)
+ * @arg TIM_TIM5_ETR_SAI2_FSB: TIM5_ETR is connected to SAI2 FS_B (*)
+ * @arg TIM_TIM5_ETR_SAI4_FSA: TIM5_ETR is connected to SAI2 FS_A (*)
+ * @arg TIM_TIM5_ETR_SAI4_FSB: TIM5_ETR is connected to SAI2 FS_B (*)
+ *
+ * For TIM8, the parameter is one of the following values:
+ * @arg TIM_TIM8_ETR_GPIO: TIM8_ETR is connected to GPIO
+ * @arg TIM_TIM8_ETR_COMP1: TIM8_ETR is connected to COMP1 output
+ * @arg TIM_TIM8_ETR_COMP2: TIM8_ETR is connected to COMP2 output
+ * @arg TIM_TIM8_ETR_ADC2_AWD1: TIM8_ETR is connected to ADC2 AWD1
+ * @arg TIM_TIM8_ETR_ADC2_AWD2: TIM8_ETR is connected to ADC2 AWD2
+ * @arg TIM_TIM8_ETR_ADC2_AWD3: TIM8_ETR is connected to ADC2 AWD3
+ * @arg TIM_TIM8_ETR_ADC3_AWD1: TIM8_ETR is connected to ADC3 AWD1
+ * @arg TIM_TIM8_ETR_ADC3_AWD2: TIM8_ETR is connected to ADC3 AWD2
+ * @arg TIM_TIM8_ETR_ADC3_AWD3: TIM8_ETR is connected to ADC3 AWD3
+ *
+ * For TIM23, the parameter is one of the following values: (*)
+ * @arg TIM_TIM23_ETR_GPIO TIM23_ETR is connected to GPIO
+ * @arg TIM_TIM23_ETR_COMP1 TIM23_ETR is connected to COMP1 output
+ * @arg TIM_TIM23_ETR_COMP2 TIM23_ETR is connected to COMP2 output
+ *
+ * For TIM24, the parameter is one of the following values: (*)
+ * @arg TIM_TIM24_ETR_GPIO TIM24_ETR is connected to GPIO
+ * @arg TIM_TIM24_ETR_SAI4_FSA TIM24_ETR is connected to SAI4 FS_A
+ * @arg TIM_TIM24_ETR_SAI4_FSB TIM24_ETR is connected to SAI4 FS_B
+ * @arg TIM_TIM24_ETR_SAI1_FSA TIM24_ETR is connected to SAI1 FS_A
+ * @arg TIM_TIM24_ETR_SAI1_FSB TIM24_ETR is connected to SAI1 FS_B
+ *
+ * (*) Value not defined in all devices.
+ *
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap)
+{
+ /* Check parameters */
+ assert_param(IS_TIM_REMAP_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_REMAP(Remap));
+
+ __HAL_LOCK(htim);
+
+ MODIFY_REG(htim->Instance->AF1, TIM1_AF1_ETRSEL_Msk, Remap);
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Select the timer input source
+ * @param htim TIM handle.
+ * @param Channel specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TI1 input channel
+ * @arg TIM_CHANNEL_2: TI2 input channel
+ * @arg TIM_CHANNEL_3: TIM Channel 3
+ * @arg TIM_CHANNEL_4: TIM Channel 4
+ * @param TISelection parameter of the TIM_TISelectionStruct structure is detailed as follows:
+ * For TIM1, the parameter is one of the following values:
+ * @arg TIM_TIM1_TI1_GPIO: TIM1 TI1 is connected to GPIO
+ * @arg TIM_TIM1_TI1_COMP1: TIM1 TI1 is connected to COMP1 output
+ *
+ * For TIM2, the parameter is one of the following values:
+ * @arg TIM_TIM2_TI4_GPIO: TIM2 TI4 is connected to GPIO
+ * @arg TIM_TIM2_TI4_COMP1: TIM2 TI4 is connected to COMP1 output
+ * @arg TIM_TIM2_TI4_COMP2: TIM2 TI4 is connected to COMP2 output
+ * @arg TIM_TIM2_TI4_COMP1_COMP2: TIM2 TI4 is connected to logical OR between COMP1 and COMP2 output
+ *
+ * For TIM3, the parameter is one of the following values:
+ * @arg TIM_TIM3_TI1_GPIO: TIM3 TI1 is connected to GPIO
+ * @arg TIM_TIM3_TI1_COMP1: TIM3 TI1 is connected to COMP1 output
+ * @arg TIM_TIM3_TI1_COMP2: TIM3 TI1 is connected to COMP2 output
+ * @arg TIM_TIM3_TI1_COMP1_COMP2: TIM3 TI1 is connected to logical OR between COMP1 and COMP2 output
+ *
+ * For TIM5, the parameter is one of the following values:
+ * @arg TIM_TIM5_TI1_GPIO: TIM5 TI1 is connected to GPIO
+ * @arg TIM_TIM5_TI1_CAN_TMP: TIM5 TI1 is connected to CAN TMP
+ * @arg TIM_TIM5_TI1_CAN_RTP: TIM5 TI1 is connected to CAN RTP
+ *
+ * For TIM8, the parameter is one of the following values:
+ * @arg TIM_TIM8_TI1_GPIO: TIM8 TI1 is connected to GPIO
+ * @arg TIM_TIM8_TI1_COMP2: TIM8 TI1 is connected to COMP2 output
+ *
+ * For TIM12, the parameter can have the following values: (*)
+ * @arg TIM_TIM12_TI1_GPIO: TIM12 TI1 is connected to GPIO
+ * @arg TIM_TIM12_TI1_SPDIF_FS: TIM12 TI1 is connected to SPDIF FS
+ *
+ * For TIM15, the parameter is one of the following values:
+ * @arg TIM_TIM15_TI1_GPIO: TIM15 TI1 is connected to GPIO
+ * @arg TIM_TIM15_TI1_TIM2: TIM15 TI1 is connected to TIM2 CH1
+ * @arg TIM_TIM15_TI1_TIM3: TIM15 TI1 is connected to TIM3 CH1
+ * @arg TIM_TIM15_TI1_TIM4: TIM15 TI1 is connected to TIM4 CH1
+ * @arg TIM_TIM15_TI1_LSE: TIM15 TI1 is connected to LSE
+ * @arg TIM_TIM15_TI1_CSI: TIM15 TI1 is connected to CSI
+ * @arg TIM_TIM15_TI1_MCO2: TIM15 TI1 is connected to MCO2
+ * @arg TIM_TIM15_TI2_GPIO: TIM15 TI2 is connected to GPIO
+ * @arg TIM_TIM15_TI2_TIM2: TIM15 TI2 is connected to TIM2 CH2
+ * @arg TIM_TIM15_TI2_TIM3: TIM15 TI2 is connected to TIM3 CH2
+ * @arg TIM_TIM15_TI2_TIM4: TIM15 TI2 is connected to TIM4 CH2
+ *
+ * For TIM16, the parameter can have the following values:
+ * @arg TIM_TIM16_TI1_GPIO: TIM16 TI1 is connected to GPIO
+ * @arg TIM_TIM16_TI1_LSI: TIM16 TI1 is connected to LSI
+ * @arg TIM_TIM16_TI1_LSE: TIM16 TI1 is connected to LSE
+ * @arg TIM_TIM16_TI1_RTC: TIM16 TI1 is connected to RTC wakeup interrupt
+ *
+ * For TIM17, the parameter can have the following values:
+ * @arg TIM_TIM17_TI1_GPIO: TIM17 TI1 is connected to GPIO
+ * @arg TIM_TIM17_TI1_SPDIF_FS: TIM17 TI1 is connected to SPDIF FS (*)
+ * @arg TIM_TIM17_TI1_HSE_1MHZ: TIM17 TI1 is connected to HSE 1MHz
+ * @arg TIM_TIM17_TI1_MCO1: TIM17 TI1 is connected to MCO1
+ *
+ * For TIM23, the parameter can have the following values: (*)
+ * @arg TIM_TIM23_TI4_GPIO TIM23_TI4 is connected to GPIO
+ * @arg TIM_TIM23_TI4_COMP1 TIM23_TI4 is connected to COMP1 output
+ * @arg TIM_TIM23_TI4_COMP2 TIM23_TI4 is connected to COMP2 output
+ * @arg TIM_TIM23_TI4_COMP1_COMP2 TIM23_TI4 is connected to COMP2 output
+ *
+ * For TIM24, the parameter can have the following values: (*)
+ * @arg TIM_TIM24_TI1_GPIO TIM24_TI1 is connected to GPIO
+ * @arg TIM_TIM24_TI1_CAN_TMP TIM24_TI1 is connected to CAN_TMP
+ * @arg TIM_TIM24_TI1_CAN_RTP TIM24_TI1 is connected to CAN_RTP
+ * @arg TIM_TIM24_TI1_CAN_SOC TIM24_TI1 is connected to CAN_SOC
+ *
+ * (*) Value not defined in all devices. \n
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_TISelection(TIM_HandleTypeDef *htim, uint32_t TISelection, uint32_t Channel)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ /* Check parameters */
+ assert_param(IS_TIM_TISEL_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_TISEL(TISelection));
+
+ __HAL_LOCK(htim);
+
+ switch (Channel)
+ {
+ case TIM_CHANNEL_1:
+ MODIFY_REG(htim->Instance->TISEL, TIM_TISEL_TI1SEL, TISelection);
+ break;
+ case TIM_CHANNEL_2:
+ MODIFY_REG(htim->Instance->TISEL, TIM_TISEL_TI2SEL, TISelection);
+ break;
+ case TIM_CHANNEL_3:
+ MODIFY_REG(htim->Instance->TISEL, TIM_TISEL_TI3SEL, TISelection);
+ break;
+ case TIM_CHANNEL_4:
+ MODIFY_REG(htim->Instance->TISEL, TIM_TISEL_TI4SEL, TISelection);
+ break;
+ default:
+ status = HAL_ERROR;
+ break;
+ }
+
+ __HAL_UNLOCK(htim);
+
+ return status;
+}
+
+/**
+ * @brief Group channel 5 and channel 1, 2 or 3
+ * @param htim TIM handle.
+ * @param Channels specifies the reference signal(s) the OC5REF is combined with.
+ * This parameter can be any combination of the following values:
+ * TIM_GROUPCH5_NONE: No effect of OC5REF on OC1REFC, OC2REFC and OC3REFC
+ * TIM_GROUPCH5_OC1REFC: OC1REFC is the logical AND of OC1REFC and OC5REF
+ * TIM_GROUPCH5_OC2REFC: OC2REFC is the logical AND of OC2REFC and OC5REF
+ * TIM_GROUPCH5_OC3REFC: OC3REFC is the logical AND of OC3REFC and OC5REF
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_TIMEx_GroupChannel5(TIM_HandleTypeDef *htim, uint32_t Channels)
+{
+ /* Check parameters */
+ assert_param(IS_TIM_COMBINED3PHASEPWM_INSTANCE(htim->Instance));
+ assert_param(IS_TIM_GROUPCH5(Channels));
+
+ /* Process Locked */
+ __HAL_LOCK(htim);
+
+ htim->State = HAL_TIM_STATE_BUSY;
+
+ /* Clear GC5Cx bit fields */
+ htim->Instance->CCR5 &= ~(TIM_CCR5_GC5C3 | TIM_CCR5_GC5C2 | TIM_CCR5_GC5C1);
+
+ /* Set GC5Cx bit fields */
+ htim->Instance->CCR5 |= Channels;
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+ __HAL_UNLOCK(htim);
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions
+ * @brief Extended Callbacks functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Extended Callbacks functions #####
+ ==============================================================================
+ [..]
+ This section provides Extended TIM callback functions:
+ (+) Timer Commutation callback
+ (+) Timer Break callback
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Hall commutation changed callback in non-blocking mode
+ * @param htim TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef *htim)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(htim);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_TIMEx_CommutCallback could be implemented in the user file
+ */
+}
+/**
+ * @brief Hall commutation changed half complete callback in non-blocking mode
+ * @param htim TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef *htim)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(htim);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_TIMEx_CommutHalfCpltCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Hall Break detection callback in non-blocking mode
+ * @param htim TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(htim);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_TIMEx_BreakCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Hall Break2 detection callback in non blocking mode
+ * @param htim: TIM handle
+ * @retval None
+ */
+__weak void HAL_TIMEx_Break2Callback(TIM_HandleTypeDef *htim)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(htim);
+
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_TIMEx_Break2Callback could be implemented in the user file
+ */
+}
+/**
+ * @}
+ */
+
+/** @defgroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions
+ * @brief Extended Peripheral State functions
+ *
+@verbatim
+ ==============================================================================
+ ##### Extended Peripheral State functions #####
+ ==============================================================================
+ [..]
+ This subsection permits to get in run-time the status of the peripheral
+ and the data flow.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Return the TIM Hall Sensor interface handle state.
+ * @param htim TIM Hall Sensor handle
+ * @retval HAL state
+ */
+HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim)
+{
+ return htim->State;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup TIMEx_Private_Functions TIMEx Private Functions
+ * @{
+ */
+
+/**
+ * @brief TIM DMA Commutation callback.
+ * @param hdma pointer to DMA handle.
+ * @retval None
+ */
+void TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma)
+{
+ TIM_HandleTypeDef *htim = (TIM_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1)
+ htim->CommutationCallback(htim);
+#else
+ HAL_TIMEx_CommutCallback(htim);
+#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */
+}
+
+/**
+ * @brief TIM DMA Commutation half complete callback.
+ * @param hdma pointer to DMA handle.
+ * @retval None
+ */
+void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef *hdma)
+{
+ TIM_HandleTypeDef *htim = (TIM_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent;
+
+ /* Change the htim state */
+ htim->State = HAL_TIM_STATE_READY;
+
+#if (USE_HAL_TIM_REGISTER_CALLBACKS == 1)
+ htim->CommutationHalfCpltCallback(htim);
+#else
+ HAL_TIMEx_CommutHalfCpltCallback(htim);
+#endif /* USE_HAL_TIM_REGISTER_CALLBACKS */
+}
+
+
+/**
+ * @brief Enables or disables the TIM Capture Compare Channel xN.
+ * @param TIMx to select the TIM peripheral
+ * @param Channel specifies the TIM Channel
+ * This parameter can be one of the following values:
+ * @arg TIM_CHANNEL_1: TIM Channel 1
+ * @arg TIM_CHANNEL_2: TIM Channel 2
+ * @arg TIM_CHANNEL_3: TIM Channel 3
+ * @param ChannelNState specifies the TIM Channel CCxNE bit new state.
+ * This parameter can be: TIM_CCxN_ENABLE or TIM_CCxN_Disable.
+ * @retval None
+ */
+static void TIM_CCxNChannelCmd(TIM_TypeDef *TIMx, uint32_t Channel, uint32_t ChannelNState)
+{
+ uint32_t tmp;
+
+ tmp = TIM_CCER_CC1NE << (Channel & 0x1FU); /* 0x1FU = 31 bits max shift */
+
+ /* Reset the CCxNE Bit */
+ TIMx->CCER &= ~tmp;
+
+ /* Set or reset the CCxNE Bit */
+ TIMx->CCER |= (uint32_t)(ChannelNState << (Channel & 0x1FU)); /* 0x1FU = 31 bits max shift */
+}
+/**
+ * @}
+ */
+
+#endif /* HAL_TIM_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|