blob: 6c00c5d267e65a7c936d0ee795f06ddf3323054a (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
@c
@c COPYRIGHT (c) 1988-2002.
@c On-Line Applications Research Corporation (OAR).
@c All rights reserved.
@chapter Clock Driver
@section Introduction
The purpose of the clock driver is to provide a steady time
basis to the kernel, so that the RTEMS primitives that need
a clock tick work properly. See the @code{Clock Manager} chapter
of the @b{RTEMS Application C User's Guide} for more details.
The clock driver is located in the @code{clock} directory of the BSP.
@section Clock Driver Global Variables
This section describes the global variables expected to be provided by
this driver.
@subsection Major and Minor Number
The major and minor numbers of the clock driver are made available via
the following variables.
@itemize @bullet
@item rtems_device_major_number rtems_clock_major;
@item rtems_device_minor_number rtems_clock_minor;
@end itemize
The clock device driver is responsible for declaring and
initializing these variables. These variables are used
by other RTEMS components -- notably the Shared Memory Driver.
@b{NOTE:} In a future RTEMS version, these variables may be replaced
with the clock device driver registering @b{/dev/clock}.
@subsection Ticks Counter
Most of the clock device drivers provide a global variable
that is simply a count of the number of clock driver interrupt service
routines that have occured. This information is valuable when debugging
a system. This variable is declared as follows:
@example
volatile uint32_t Clock_driver_ticks;
@end example
@section Initialization
The initialization routine is responsible for
programming the hardware that will periodically
generate an interrupt. A programmable interval timer is commonly
used as the source of the clock tick.
The device should be programmed such that an interrupt is generated
every @i{m} microseconds, where @i{m} is equal to
@code{rtems_configuration_get_microseconds_per_tick()}. Sometimes
the periodic interval timer can use a prescaler so you have to look
carefully at your user's manual to determine the correct value.
You must use the RTEMS primitive @code{rtems_interrupt_catch} to install
your clock interrupt service routine:
@example
rtems_interrupt_catch (Clock_ISR, CLOCK_VECTOR, &old_handler);
@end example
Since there is currently not a driver entry point invoked at system
shutdown, many clock device drivers use the @code{atexit} routine
to schedule their @code{Clock_exit} routine to execute when the
system is shutdown.
By convention, many of the clock drivers do not install the clock
tick if the @code{ticks_per_timeslice} field of the Configuration
Table is 0.
@section System shutdown
Many drivers provide the routine @code{Clock_exit} that is scheduled
to be run during system shutdown via the @code{atexit} routine.
The @code{Clock_exit} routine will disable the clock tick source
if it was enabled. This can be used to prevent clock ticks after the
system is shutdown.
@section Clock Interrupt Subroutine
It only has to inform the kernel that a ticker has elapsed, so call :
@example
@group
rtems_isr Clock_isr( rtems_vector_number vector )
@{
invoke the rtems_clock_tick() directive to announce the tick
if necessary for this hardware
reload the programmable timer
@}
@end group
@end example
@section IO Control
Prior to RTEMS 4.9, the Shared Memory MPCI Driver required a special
IOCTL in the Clock Driver. This is no longer required and the Clock
Driver does not have to provide an IOCTL method at all.
|
