/* Based upon IDT provided code with the following release: This source code has been made available to you by IDT on an AS-IS basis. Anyone receiving this source is licensed under IDT copyrights to use it in any way he or she deems fit, including copying it, modifying it, compiling it, and redistributing it either with or without modifications. No license under IDT patents or patent applications is to be implied by the copyright license. Any user of this software should understand that IDT cannot provide technical support for this software and will not be responsible for any consequences resulting from the use of this software. Any person who transfers this source code or any derivative work must include the IDT copyright notice, this paragraph, and the preceeding two paragraphs in the transferred software. COPYRIGHT IDT CORPORATION 1996 LICENSED MATERIAL - PROGRAM PROPERTY OF IDT */ /************************************************************************* ** ** Copyright 1991-95 Integrated Device Technology, Inc. ** All Rights Reserved ** **************************************************************************/ /* * $Id$ */ #include #include #include #if 0 .extern _fdata,4 /* this is defined by the linker */ .extern _edata,4 /* this is defined by the linker */ .extern _idata,4 /* this is defined by the linker */ #endif .extern _fbss,4 /* this is defined by the linker */ .extern end,4 /* this is defined by the linker */ .lcomm sim_mem_cfg_struct,12 .text /* For the V3 Eval board, we can safely assume that we have at least 16 megabytes of RAM */ #define HARD_CODED_MEM_SIZE 0x1000000 #define TMP_STKSIZE 1024 /* ** P_STACKSIZE is the size of the Prom Stack. ** the prom stack grows downward */ #define P_STACKSIZE 0x2000 /* sets stack size to 8k */ /************************************************************************** ** ** start - Typical standalone start up code required for R3000/R4000 ** ** ** 1) Initialize the STATUS Register ** a) Clear parity error bit ** b) Set co_processor 1 usable bit ON ** c) Clear all IntMask Enables ** d) Set kernel/disabled mode ** 2) Initialize Cause Register ** a) clear software interrupt bits ** 3) Determine FPU installed or not ** if not, clear CoProcessor 1 usable bit ** 4) Clear bss area ** 5) MUST allocate temporary stack until memory size determined ** It MUST be uncached to prevent overwriting when caches are cleared ** 6) Install exception handlers ** 7) Determine memory and cache sizes ** 8) Establish permanent stack (cached or uncached as defined by bss) ** 9) Flush Instruction and Data caches ** 10) If there is a Translation Lookaside Buffer, Clear the TLB ** 11) Execute initialization code if the IDT/c library is to be used ** ** 12) Jump to user's "main()" (boot_card() for RTEMS) ** 13) Jump to promexit ** ** IDT/C 5.x defines _R3000, IDT/C 6.x defines _R4000 internally. ** This is used to mark code specific to R3xxx or R4xxx processors. ** IDT/C 6.x defines __mips to be the ISA level for which we're ** generating code. This is used to make sure the stack etc. is ** double word aligned, when using -mips3 (default) or -mips2, ** when compiling with IDT/C6.x ** ***************************************************************************/ FRAME(start,sp,0,ra) .set noreorder #if __mips_fpr == 64 li v0,SR_CU1|SR_FR|SR_DE /* initally clear ERL, enable FPU with 64 bit regs, disable cache errors */ #else li v0,SR_CU1|SR_DE /* initally clear ERL, enable FPU with 32 bit regs, disable cache errors */ #endif mtc0 v0,C0_SR /* clr IntMsks/ kernel/disabled mode */ nop mtc0 zero,C0_CAUSE /* clear software interrupts */ nop la t0,0xBE200000 /* on Hurricane board, enable interrupt output signal from UART ch. B */ li t1,0x8 /* UART INT B signal is left tri-state'd after reset, this results in processor interrupt signal being driven active low */ sw t1,0x10(t0) li v0,CFG_C_NONCOHERENT # initialise default cache mode mtc0 v0,C0_CONFIG /* ** check to see if an fpu is really plugged in */ li t3,0xaaaa5555 /* put a's and 5's in t3 */ mtc1 t3,fp0 /* try to write them into fp0 */ mtc1 zero,fp1 /* try to write zero in fp */ mfc1 t0,fp0 mfc1 t1,fp1 nop bne t0,t3,1f /* branch if no match */ nop bne t1,zero,1f /* double check for positive id */ nop /* We have a FPU. clear fcsr */ ctc1 zero, fcr31 j 2f /* status register already correct */ nop 1: li v0,SR_DE /* clear ERL and disable FPA */ mtc0 v0, C0_SR /* reset status register */ 2: la gp, _gp #if 0 /* Initialize data sections from "rom" copy */ la t0,_idata /* address of initialization data (copy of data sections placed in ROM) */ la t1,_fdata /* start of initialized data section */ la t2,_edata /* end of initialized data section */ 3: lw t3,0(t0) sw t3,0(t1) addiu t1,t1,4 bne t1,t2,3b addiu t0,t0,4 #endif /* clear bss before using it */ la v0,_fbss /* start of bss */ la v1,end /* end of bss */ 4: sw zero,0(v0) bltu v0,v1,4b add v0,4 /************************************************************************ ** ** Temporary Stack - needed to handle stack saves until ** memory size is determined and permanent stack set ** ** MUST be uncached to avoid confusion at cache ** switching during memory sizing ** *************************************************************************/ /* For MIPS 3, we need to be sure that the stack is aligned on a * double word boundary. */ andi t0, v0, 0x7 beqz t0, 11f /* Last three bits Zero, already aligned */ nop add v0, 4 11: or v0, K1BASE /* switch to uncached */ add v1, v0, TMP_STKSIZE /* end of bss + length of tmp stack */ sub v1, v1, (4*4) /* overhead */ move sp, v1 /* set sp to top of stack */ 4: sw zero, 0(v0) bltu v0, v1, 4b /* clear out temp stack */ add v0, 4 /* jal init_exc_vecs */ /* install exception handlers */ /* nop */ /* MUST do before memory probes */ /* Force processor into uncached space during memory/cache probes */ la v0, 5f li v1, K1BASE or v0, v1 j v0 nop 5: li a0, HARD_CODED_MEM_SIZE /* Set memory size global */ jal set_memory_size nop la a0, sim_mem_cfg_struct jal get_mem_conf /* Make call to get mem size */ nop la a0, sim_mem_cfg_struct lw a0, 0(a0) /* Get memory size from struct */ jal config_cache /* determine size of D & I caches */ nop move v0, a0 /* mem_size */ /* For MIPS 3, we need to be sure that the stack (and hence v0 * here) is aligned on a double word boundary. */ andi t0, v0, 0x7 beqz t0, 12f /* Last three bits Zero, already aligned */ nop subu v0, 4 /* mem_size was not aligned on doubleword bdry????*/ 12: /************************************************************************** ** ** Permanent Stack - now know top of memory, put permanent stack there ** ***************************************************************************/ la t2, _fbss /* cache mode as linked */ and t2, 0xF0000000 /* isolate segment */ la t1, 6f j t1 /* back to original cache mode */ nop 6: or v0, t2 /* stack back to original cache mode */ addiu v0,v0,-16 /* overhead */ move sp, v0 /* now replace count w top of memory */ move v1, v0 subu v1, P_STACKSIZE /* clear requested stack size */ 7: sw zero, 0(v1) /* clear P_STACKSIZE stack */ bltu v1,v0,7b add v1, 4 .set reorder /* FIX THIS - This corrupts memory spaces */ /* jal flush_cache_nowrite */ /* flush Data & Instruction caches */ /* jal mon_flush_cache */ /************************************************************************** ** ** If this chip supports a Translation Lookaside Buffer, clear it ** ***************************************************************************/ .set noreorder mfc0 t1, C0_SR /* look at Status Register */ nop .set reorder jal init_tlb /* clear the tlb */ /* Force processor into cached instruction space for rest of initialization */ #if 0 la t0, 1f li t1, K0BASE /* force into cached space */ or t0, t1 j t0 nop 1: #endif /************************************************************************ ** ** Initialization required if using IDT/c or libc.a, standard C Lib ** ** can SKIP if not necessary for application ** ************************************************************************/ 8: /* FIX THIS - Need the pmon equivalent jal idtsim_init_sbrk jal idtsim_init_file */ /*********************** END I/O initialization **********************/ move a0,zero /* Set argc passed to main */ move a1,zero /* Set argv passed to main */ jal boot_card nop # jump to the "exit" routine jal _sys_exit move a0,v0 # pass through the exit code # FIX THIS - Need the pmon equivalent # jal idtsim_promexit 1: beq zero,zero,1b nop ENDFRAME(start) /* * _sys_exit -- Exit from the application. Normally we cause a user trap * to return to the ROM monitor for another run. NOTE: This is * the only other routine we provide in the crt0.o object, since * it may be tied to the "_start" routine. It also allows * executables that contain a complete world to be linked with * just the crt0.o object. */ FRAME(_sys_exit,sp,0,ra) break 1023 nop 13: b 13b # but loop back just in-case nop ENDFRAME(_sys_exit) .globl __sizemem .ent __sizemem __sizemem: li v0,HARD_CODED_MEM_SIZE j ra nop .end __sizemem