From 97b8b8f5fa568d2cdb96a39d0e7acd63d38cedd2 Mon Sep 17 00:00:00 2001 From: Joel Sherrill Date: Tue, 2 Mar 1999 15:56:04 +0000 Subject: This file is linked in --- doc/bsp_howto/network.t | 284 ------------------------------------------------ 1 file changed, 284 deletions(-) delete mode 100644 doc/bsp_howto/network.t (limited to 'doc/bsp_howto/network.t') diff --git a/doc/bsp_howto/network.t b/doc/bsp_howto/network.t deleted file mode 100644 index e7e5c4335b..0000000000 --- a/doc/bsp_howto/network.t +++ /dev/null @@ -1,284 +0,0 @@ -@c -@c Written by Eric Norum -@c -@c COPYRIGHT (c) 1988-1998. -@c On-Line Applications Research Corporation (OAR). -@c All rights reserved. -@c -@c $Id$ -@c - -@chapter Networking Driver - -@section Introduction - -This chapter is intended to provide an introduction to the -procedure for writing RTEMS network device drivers. -The example code is taken from the `Generic 68360' network device -driver. The source code for this driver is located in the -@code{c/src/lib/libbsp/m68k/gen68360/network} directory in the RTEMS -source code distribution. You should have a copy of this driver at -hand when reading the following notes. - -@section Learn about the network device - -Before starting to write the network driver you need to be completely -familiar with the programmer's view of the device. -The following points list some of the details of the -device that must be understood before a driver can be written. - -@itemize @bullet - -@item Does the device use DMA to transfer packets to and from -memory or does the processor have to -copy packets to and from memory on the device? - -@item If the device uses DMA, is it capable of forming a single -outtoing packet from multiple fragments scattered in separate -memory buffers? - -@item If the device uses DMA, is it capable of chaining multiple -outgoing packets, or does each outgoing packet require -intervention by the driver? - -@item Does the device automatically pad short frames to the minimum -64 bytes or does the driver have to supply the padding? - -@item Does the device automatically retry a transmission on detection -of a collision? - -@item If the device uses DMA, is it capable of buffering multiple -packets to memory, or does the receiver have to be restarted -after the arrival of each packet? - -@item How are packets that are too short, too long, or received with -CRC errors handled? Does the device automatically continue -reception or does the driver have to intervene? - -@item How is the device Ethernet address set? How is the device -programmed to accept or reject broadcast and multicast packets? - -@item What interrupts does the device generate? Does it generate an -interrupt for each incoming packet, or only for packets received -without error? Does it generate an interrupt for each packet -transmitted, or only when the transmit queue is empty? What -happens when a transmit error is detected? - -@end itemize - -In addition, some controllers have specific questions regarding -board specific configuration. For example, the SONIC Ethernet -controller has a very configurable data bus interface. It can -even be configured for sixteen and thirty-two bit data buses. This -type of information should be obtained from the board vendor. - -@section Understand the network scheduling conventions - -When writing code for your driver transmit and receive tasks you must -take care to follow the network scheduling conventions. All tasks -which are associated with networking share various -data structures and resources. To ensure the consistency -of these structures the tasks -execute only when they hold the network semaphore (@code{rtems_bsdnet_semaphore}). -Your transmit and receive tasks must abide by this protocol which means you must -be careful to avoid `deadly embraces' with the other network tasks. -A number of routines are provided to make it easier for your code -to conform to the network task scheduling conventions. - -@itemize @bullet - -@item @code{void rtems_bsdnet_semaphore_release(void)} - -This function releases the network semaphore. -Your task must call this function immediately before -making any blocking RTEMS request. - -@item @code{void rtems_bsdnet_semaphore_obtain(void)} - -This function obtains the network semaphore. -If your task has released the network semaphore to allow other -network-related tasks to run while your task blocks you must call this -function to reobtain the semaphore immediately after the return from the -blocking RTEMS request. - -@item @code{rtems_bsdnet_event_receive(rtems_event_set, rtems_option, rtems_interval, rtems_event_set *)} -Your task should call this function when it wishes to wait for an event. -This function releases the network semaphore, -calls @code{rtems_event_receive} to wait for the specified event -or events and reobtains the semaphore. -The value returned is the value returned by the @code{rtems_event_receive}. - -@end itemize - -@section Write your driver attach function -The driver attach function is responsible for configuring the driver -and making the connection between the network stack -and the driver. - -Driver attach functions take a pointer to an -@code{rtems_bsdnet_ifconfig} structure as their only argument. -and set the driver parameters based on the -values in this structure. If an entry in the configuration -structure is zero the attach function chooses an -appropriate default value for that parameter. - - -The driver should then set up several fields in the ifnet structure -in the device-dependent data structure supplied and maintained by the driver: - -@table @code -@item ifp->if_softc -Pointer to the device-dependent data. The first entry -in the device-dependent data structure must be an @code{arpcom} -structure. - -@item ifp->if_name -The name of the device. The network stack uses this string -and the device number for device name lookups. The name should not -contain digits as these will be assumed to be part of the unit number -and not part of the device name. - - -@item ifp->if_unit -The device number. The network stack uses this number and the -device name for device name lookups. For example, if -@code{ifp->if_name} is @samp{scc}, and @code{ifp->if_unit} is @samp{1}, -the full device name would be @samp{scc1}. - -@item ifp->if_mtu -The maximum transmission unit for the device. For Ethernet -devices this value should almost always be 1500. - -@item ifp->if_flags -The device flags. Ethernet devices should set the flags -to @code{IFF_BROADCAST|IFF_SIMPLEX}, indicating that the -device can broadcast packets to multiple destinations -and does not receive and transmit at the same time. - -@item ifp->if_snd.ifq_maxlen -The maximum length of the queue of packets waiting to be -sent to the driver. This is normally set to @code{ifqmaxlen}. - -@item ifp->if_init -The address of the driver initialization function. - -@item ifp->if_start -The address of the driver start function. - -@item ifp->if_ioctl -The address of the driver ioctl function. - -@item ifp->if_output -The address of the output function. Ethernet devices -should set this to @code{ether_output}. -@end table - -Once the attach function has set up the above entries it must link the -driver data structure onto the list of devices by -calling @code{if_attach}. Ethernet devices should then -call @code{ether_ifattach}. Both functions take a pointer to the -device's @code{ifnet} structure as their only argument. - -The attach function should return a non-zero value to indicate that -the driver has been successfully configured and attached. - - - - -@section Write your driver start function. -This function is called each time the network stack wants to start the -transmitter. This occures whenever the network stack adds a packet -to a device's send queue and the @code{IFF_OACTIVE} bit in the -device's @code{if_flags} is not set. - -For many devices this function need only set the @code{IFF_OACTIVE} bit in the -@code{if_flags} and send an event to the transmit task -indicating that a packet is in the driver transmit queue. - - -@section Write your driver initialization function. -This function should initialize the device, attach to interrupt handler, -and start the driver transmit and receive tasks. The function - -@example -rtems_id -rtems_bsdnet_newproc (char *name, - int stacksize, - void(*entry)(void *), - void *arg); -@end example - -should be used to start the driver tasks. - -Note that the network stack may call the driver initialization function more -than once. -Make sure you don't start multiple versions of the receive and transmit tasks. - - - -@section Write your driver transmit task. -This task is reponsible for removing packets from the driver send queue and sending them to the device. The task should block waiting for an event from the -driver start function indicating that packets are waiting to be transmitted. -When the transmit task has drained the driver send queue the task should clear -the @code{IFF_OACTIVE} bit in @code{if_flags} and block until another outgoing -packet is queued. - - -@section Write your driver receive task. -This task should block until a packet arrives from the device. If the -device is an Ethernet interface the function @code{ether_input} should be called -to forward the packet to the network stack. The arguments to @code{ether_input} -are a pointer to the interface data structure, a pointer to the ethernet -header and a pointer to an mbuf containing the packet itself. - - - - -@section Write your driver interrupt handler. -A typical interrupt handler will do nothing more than the hardware -manipulation required to acknowledge the interrupt and send an RTEMS event -to wake up the driver receive or transmit task waiting for the event. -Network interface interrupt handlers must not make any calls to other -network routines. - - - -@section Write your driver ioctl function. -This function handles ioctl requests directed at the device. The ioctl -commands which must be handled are: - -@table @code -@item SIOCGIFADDR -@item SIOCSIFADDR -If the device is an Ethernet interface these -commands should be passed on to @code{ether_ioctl}. - -@item SIOCSIFFLAGS -This command should be used to start or stop the device, -depending on the state of the interface @code{IFF_UP} and -@code{IFF_RUNNING} bits in @code{if_flags}: -@table @code -@item IFF_RUNNING -Stop the device. - -@item IFF_UP -Start the device. - -@item IFF_UP|IFF_RUNNING -Stop then start the device. - -@item 0 -Do nothing. - -@end table -@end table - - - -@section Write Your Driver Statistic-Printing Function -This function should print the values of any statistic/diagnostic -counters your driver may use. The driver ioctl function should call -the statistic-printing function when the ioctl command is -@code{SIO_RTEMS_SHOW_STATS}. - - -- cgit v1.2.3