From 76c2b3546c40e4024296d7aea42b1f30d52fe611 Mon Sep 17 00:00:00 2001 From: Joel Sherrill Date: Tue, 11 Jan 2000 19:09:24 +0000 Subject: File removed as it was not being used. --- c/src/lib/libbsp/i386/i386ex/network/dma.h | 268 ----------------------------- 1 file changed, 268 deletions(-) delete mode 100644 c/src/lib/libbsp/i386/i386ex/network/dma.h (limited to 'c/src/lib/libbsp/i386/i386ex/network') diff --git a/c/src/lib/libbsp/i386/i386ex/network/dma.h b/c/src/lib/libbsp/i386/i386ex/network/dma.h deleted file mode 100644 index 51c0d0c98a..0000000000 --- a/c/src/lib/libbsp/i386/i386ex/network/dma.h +++ /dev/null @@ -1,268 +0,0 @@ -/* $Id$ - * linux/include/asm/dma.h: Defines for using and allocating dma channels. - * Written by Hennus Bergman, 1992. - * High DMA channel support & info by Hannu Savolainen - * and John Boyd, Nov. 1992. - */ - -#ifndef _ASM_DMA_H -#define _ASM_DMA_H - - - -#define dma_outb(x,y) outport_byte(y,x) - -#define dma_inb inport_byte - -/* - * NOTES about DMA transfers: - * - * controller 1: channels 0-3, byte operations, ports 00-1F - * controller 2: channels 4-7, word operations, ports C0-DF - * - * - ALL registers are 8 bits only, regardless of transfer size - * - channel 4 is not used - cascades 1 into 2. - * - channels 0-3 are byte - addresses/counts are for physical bytes - * - channels 5-7 are word - addresses/counts are for physical words - * - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries - * - transfer count loaded to registers is 1 less than actual count - * - controller 2 offsets are all even (2x offsets for controller 1) - * - page registers for 5-7 don't use data bit 0, represent 128K pages - * - page registers for 0-3 use bit 0, represent 64K pages - * - * DMA transfers are limited to the lower 16MB of _physical_ memory. - * Note that addresses loaded into registers must be _physical_ addresses, - * not logical addresses (which may differ if paging is active). - * - * Address mapping for channels 0-3: - * - * A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses) - * | ... | | ... | | ... | - * | ... | | ... | | ... | - * | ... | | ... | | ... | - * P7 ... P0 A7 ... A0 A7 ... A0 - * | Page | Addr MSB | Addr LSB | (DMA registers) - * - * Address mapping for channels 5-7: - * - * A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses) - * | ... | \ \ ... \ \ \ ... \ \ - * | ... | \ \ ... \ \ \ ... \ (not used) - * | ... | \ \ ... \ \ \ ... \ - * P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0 - * | Page | Addr MSB | Addr LSB | (DMA registers) - * - * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses - * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at - * the hardware level, so odd-byte transfers aren't possible). - * - * Transfer count (_not # bytes_) is limited to 64K, represented as actual - * count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more, - * and up to 128K bytes may be transferred on channels 5-7 in one operation. - * - */ - -#define MAX_DMA_CHANNELS 8 - -/* The maximum address that we can perform a DMA transfer to on this platform */ -#define MAX_DMA_ADDRESS 0x1000000 - -/* 8237 DMA controllers */ -#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */ -#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */ - -/* DMA controller registers */ -#define DMA1_CMD_REG 0x08 /* command register (w) */ -#define DMA1_STAT_REG 0x08 /* status register (r) */ -#define DMA1_REQ_REG 0x09 /* request register (w) */ -#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */ -#define DMA1_MODE_REG 0x0B /* mode register (w) */ -#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */ -#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */ -#define DMA1_RESET_REG 0x0D /* Master Clear (w) */ -#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */ -#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */ - -#define DMA2_CMD_REG 0xD0 /* command register (w) */ -#define DMA2_STAT_REG 0xD0 /* status register (r) */ -#define DMA2_REQ_REG 0xD2 /* request register (w) */ -#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */ -#define DMA2_MODE_REG 0xD6 /* mode register (w) */ -#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */ -#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */ -#define DMA2_RESET_REG 0xDA /* Master Clear (w) */ -#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */ -#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */ - -#define DMA_ADDR_0 0x00 /* DMA address registers */ -#define DMA_ADDR_1 0x02 -#define DMA_ADDR_2 0x04 -#define DMA_ADDR_3 0x06 -#define DMA_ADDR_4 0xC0 -#define DMA_ADDR_5 0xC4 -#define DMA_ADDR_6 0xC8 -#define DMA_ADDR_7 0xCC - -#define DMA_CNT_0 0x01 /* DMA count registers */ -#define DMA_CNT_1 0x03 -#define DMA_CNT_2 0x05 -#define DMA_CNT_3 0x07 -#define DMA_CNT_4 0xC2 -#define DMA_CNT_5 0xC6 -#define DMA_CNT_6 0xCA -#define DMA_CNT_7 0xCE - -#define DMA_PAGE_0 0x87 /* DMA page registers */ -#define DMA_PAGE_1 0x83 -#define DMA_PAGE_2 0x81 -#define DMA_PAGE_3 0x82 -#define DMA_PAGE_5 0x8B -#define DMA_PAGE_6 0x89 -#define DMA_PAGE_7 0x8A - -#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */ -#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */ -#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */ - -/* enable/disable a specific DMA channel */ -static __inline__ void enable_dma(unsigned int dmanr) -{ - if (dmanr<=3) - {dma_outb(dmanr, DMA1_MASK_REG);} - else - {dma_outb(dmanr & 3, DMA2_MASK_REG);} -} - -static __inline__ void disable_dma(unsigned int dmanr) -{ - if (dmanr<=3) - { dma_outb(dmanr | 4, DMA1_MASK_REG); } - else - { dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);} -} - -/* Clear the 'DMA Pointer Flip Flop'. - * Write 0 for LSB/MSB, 1 for MSB/LSB access. - * Use this once to initialize the FF to a known state. - * After that, keep track of it. :-) - * --- In order to do that, the DMA routines below should --- - * --- only be used while interrupts are disabled! --- - */ -static __inline__ void clear_dma_ff(unsigned int dmanr) -{ - if (dmanr<=3) - {dma_outb(0, DMA1_CLEAR_FF_REG);} - else - {dma_outb(0, DMA2_CLEAR_FF_REG);} -} - -/* set mode (above) for a specific DMA channel */ -static __inline__ void set_dma_mode(unsigned int dmanr, char mode) -{ - if (dmanr<=3) - { dma_outb(mode | dmanr, DMA1_MODE_REG);} - else - { dma_outb(mode | (dmanr&3), DMA2_MODE_REG);} -} - -/* Set only the page register bits of the transfer address. - * This is used for successive transfers when we know the contents of - * the lower 16 bits of the DMA current address register, but a 64k boundary - * may have been crossed. - */ -static __inline__ void set_dma_page(unsigned int dmanr, char pagenr) -{ - switch(dmanr) { - case 0: - {dma_outb(pagenr, DMA_PAGE_0);} - break; - case 1: - {dma_outb(pagenr, DMA_PAGE_1);} - break; - case 2: - {dma_outb(pagenr, DMA_PAGE_2);} - break; - case 3: - {dma_outb(pagenr, DMA_PAGE_3);} - break; - case 5: - {dma_outb(pagenr & 0xfe, DMA_PAGE_5);} - break; - case 6: - {dma_outb(pagenr & 0xfe, DMA_PAGE_6);} - break; - case 7: - {dma_outb(pagenr & 0xfe, DMA_PAGE_7);} - break; - } -} - - -/* Set transfer address & page bits for specific DMA channel. - * Assumes dma flipflop is clear. - */ -static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a) -{ - set_dma_page(dmanr, a>>16); - if (dmanr <= 3) { - dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE ); - dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE ); - } else { - dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE ); - dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE ); - } -} - - -/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for - * a specific DMA channel. - * You must ensure the parameters are valid. - * NOTE: from a manual: "the number of transfers is one more - * than the initial word count"! This is taken into account. - * Assumes dma flip-flop is clear. - * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7. - */ -static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count) -{ - count--; - if (dmanr <= 3) { - dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE ); - dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE ); - } else { - dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE ); - dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE ); - } -} - - -/* Get DMA residue count. After a DMA transfer, this - * should return zero. Reading this while a DMA transfer is - * still in progress will return unpredictable results. - * If called before the channel has been used, it may return 1. - * Otherwise, it returns the number of _bytes_ left to transfer. - * - * Assumes DMA flip-flop is clear. - */ -static __inline__ int get_dma_residue(unsigned int dmanr) -{ - unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE - : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE; - - /* using short to get 16-bit wrap around */ - unsigned short count,temp; - - dma_inb(io_port,count); - count ++; - dma_inb(io_port,temp); - count += temp << 8; - - return (dmanr<=3)? count : (count<<1); -} - - - - -#endif /* _ASM_DMA_H */ - - - -- cgit v1.2.3