| Commit message (Collapse) | Author | Files | Lines |
|---|
|
applied. This modified many Makefiles and custom files and makes many more
settings (network, multiprocessing, etc) gnerated by autoconf.
|
|
|
|
FP issues on this target:
The default variants of libc, libm and libgcc assume that a 68881
coprocessor is present. Without the FPSP, any floating point operation,
including printf() with a "%f" format specifier, is likely to cause an
unimplemented instruction exception.
The FPSP works with the default variants of libc, libm and libgcc. It does not
work in conjunction with the msoft-float variants. The paranoia test goes into
an infinite loop at milestone 40. I am guessing that floor() is returning an
incorrect value.
The msoft-float variants of libc, libm and libgcc appear to do floating point
I/O properly. They only failed in paranoia. Offhand, I can't think of why they
would conflict with the FPSP, so I think that there is something wrong with the
msoft-float code. It might be my installation.
Given my experiences, I decided to install the FPSP in bsp_start(), and to link
against the default variants of libc, libm and libgcc. This causes the
executables to increase in size by about 60 KB. The README file and the
mvme167.cfg specify how to remove the FPSP, and how to link against the
msoft-float variants of the libraries. This is not what Eric Norum had done: on
my host, his gen68360_040 port links RTEMS code with the msoft-float variants
of libc and libm, and the default variant of libgcc. In this configuration, the
output of printf() with "%f" is garbage on my target.
|
|
|
|
|
|
|
|
made no attempt to divide the comments up and place them with just
the appropriate files. Here is an excerpt from Ralf's email:
Changes including comments on changes I made after cycling through
all the targets:
* Added ranlib support. Now all targets use "ranlib" instead of "ar -s"
to build an index for a library. If ranlib isn't detected during
configuration, check if ar -s is working and try "ar -s" instead of
* Removed $(XXX_FOR_TARGET) from make/target.cfg.in, use $(XXX) instead now.
* gcc-target-default.cfg: LINK_XXXX-defines reworked to solve the -l
problem under posix (cf gcc-target-default.cfg)
* rtems-glom replaced by Makefile-rules inside of the wrapup/Makefile.in
that has been using rtems-glom until now.
* Removed CCC and friends in gcc-target-default.cfg, as they have been
breaking CXX support.
* Removed CONFIG.$(TARGET_ARCH).CC lines from several custom/*.cfg
files, because this is now set in custom/default.cfg.
* Added aclocal/ar-s.m4, check whether "ar -s" is working
* Added aclocal/cygwin.m4 and aclocal/exeext.m4.
* Reworked aclocal/canonicalize-tools.m4: Added ar -s check; fixes for
problems when XXX_FOR_TARGET is given via environment variables (didn't
work for gcc until now), adding cygwin check, improved autoconf-cache
handling.
* Removed -l from make rule dependencies. LINK_LIBS is now allowed to
contain -L and -l. LINK_OBJS and LINK_FILES must not contain -L or -l.
gcc28 make-exe rules now link using $(LINK_OBJS) $(LINK_LIBS) => Almost
all custom/*.cfg are modified. This is very likely to break something
because of typos or having missed to edit a file.
Open problems, known bugs, things I didn't do:
* custom/p4000.cfg seems to be out of date and requires to be reviewed.
(JRS NOTE: It is subordinate p4650 and p4600 -- both of which build ok
after minor changes.)
* custom/psim.cfg needs to be reviewed, I added some changes to it, I am
insecure about.
(JRS NOTE: psim had a minor problem endif/endef swapped but runs fine.)
* rtems-glom.in can now be removed.
* gcc*.cfg files "make depend" rules don't honor language specific flags
(e.g CXXFLAGS is ignored for *.cc) - Nothing to worry about now, but may
cause problems for hosts/targets not using gcc or rtems-add-ons that use
external packages.
* AFAIS, the no_bsp BSP can't be build anymore, i.e. configure refused
to configure for it whatever I tried.
* The toplevel and toplevel+1 README files are quite out-dated
* cygwin.m4 isn't of much use for rtems. In most cases (cf.
aclocal/*.m4) it is worked around by directly using $host_os. I think
I'll remove it soon after the next snapshot
* Before release the cygwin patch needs to be tested under cygwin. I may
have broken/missed something (esp. the sed-pattern to convert \\ into /
may be broken).
* You should try to build/run the posix-BSP under solaris - I don't
expect problems, but I am not 100% sure, esp. with regard to ranlib/ar -s.
* You should consider to convert all make/compilers/*.cfg files into
make/compilers/*.cfg.in files and let autoconf generate the *.cfg. This
may help getting rid of some if/then/else statements and help
hard-coding some defines into those files in future and shouldn't
disturb now.
* Not having installed libc.a/libm.a on a host may still break building
rtems, esp. when using -disable-gcc28 as the gcc27-configuration scheme
directly accesses libc.a and libm.a. The problem should not appear when
using gcc28 because it references libc/libm only through -lc and -lm
which may be static or dynamic (I didn't test this).
* shgen is not yet included (I didn't yet have enough time to integrate it).
* I know about a few more configure-probs (esp. cross-checking
--enable-* flags).
+ warn/refuse to configure when --enable-libcdir and
--enable-gcc28 are given.
+ force --enable-libcdir when --disable-gcc28 is given
* Replaced KSHELL with @KSH@ in some shell scripts generated by configure.in.
* Added a dependency to aclocal/*.m4 in the toplevel Makefile => configure
and aclocal.m4 will now be rebuild when any aclocal/*.m4 file is changed
* Some changes to aclocal/gcc-pipe.m4 and aclocal/gcc-specs.m4
* Replaced i[[3456]]86-unknown-freebsd2.[[12]] with i[[3456]]86-*freebsd2.*
in configure.in, as I suppose there might exist a variety of valid vendors
(2nd field of the name-tripple)
* Disabled override MAKEFLAGS in toplevel Makefile.in - Potential
side-effects are not really clear to me.
* In mvme162.cfg, $(LINK_LIBS) is missing in the CC line in gcc28's make-exe
rule (yet another one I missed to edit). Just append $(LINK_LIBS) to
the "CC" line, like I hopefully did to ALL other custom/*.cfg files.
* the problem with mvme162lx.cfg is a follow-up problem of the
mvme162.cfg-bug.
* mvme162/console and idp/console had variables named Buffer which
conflicted with similarly named variables in some tests.
|
|
eliminates the need to build the entire application with the
STACK_CHECKER_ON macro defined.
|
|
|
|
|
