| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
| |
IO handlers scheme that was implemented originally just to support
sockets. The file system IO switch is more general and works fine.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
> 5) rtems-rc-19990202-1.diff/reorg-install.sh
>
> reorg-install.sh fixes a Makefile variable name clash of RTEMS
> configuration files and automake/autoconf standards.
> Until now, RTEMS used $(INSTALL) for install-if-change. Automake and
> autoconf use $(INSTALL) for a bsd-compatible install. As
> install-if-change and bsd-install are not compatible, I renamed all
> references to install-if-changed to $(INSTALL_CHANGED) and used
> $(INSTALL) for bsd-install (==automake/autoconf standard). When
> automake will be introduced install-if-change will probably be replaced
> by $(INSTALL) and therefore will slowly vanish. For the moment, this
> patch fixes a very nasty problem which prevents adding any automake file
> until now (There are still more).
|
| | |
|
| | |
|
| |
|
|
| |
NULL pointer.
|
| |
|
|
| |
so that the libc code did not have to know about (struct socket).
|
| | |
|
| |
|
|
| |
all conflicts.
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
RTEMS permits using the SO_SNDTIMEO and SO_RCVTIMEO socket options to
set a timeout for most socket I/O operations. However, in RTEMS
4.0.0, those options do not affect connect or accept. I don't know of
any way to put a timeout on those calls in RTEMS 4.0.0; can anybody
point to one.
Since it is frequently useful to have a timeout on accept, and
sometimes useful to have a timeout on connect shorter than the BSD
system default of 75 seconds, the following patch causes SO_RCVTIMEO
to affect connect and accept.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
1) Socket timeout field changed from `short' to `long'. This makes longer
timeouts possible. With a 1 kHz system clock the old system allowed
timeouts only up to a little over 30 seconds! This change is a
slightly cleaned-up version of the patch proposed by Ian Lance Taylor.
2) Major changes to BOOTP/DHCP reply handling. Now supports much of
RFC2132. These changes were done at the request of, and with the
assistance of, Erik Ivanenko.
If you're making changes, you might want to change the network
supplement Essentially just do a global search and replace of BOOTP
with BOOTP/DHCP.
|
| |
|
|
| |
in include file order.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remember the test to see if a socket could be read and written at
the same time by two different tasks? I discovered that if both
tasks attempt to close the socket a panic can occur from inside the
BSD code.
Closing the same socket twice from two different threads is
certainly an error, but a panic is not the greatest error reporting
method :-)
The following small change to the socket close routine should reduce
the chances of the panic.
|
| |
|
|
|
|
|
| |
Here's a patch to make the rtems_showroute routine a little more
useful. For `host' route table entries the link-level address is now
displayed. This is equivalent to the old `show arp table'
information displayed by the KA9Q code.
|
| |
|
|
| |
message after comments from Eric Valette <valette@crf.canon.fr>.
|
| | |
|
| |
|
|
|
| |
I have reworked the ethernet driver for the BSP pc386 and
here is the patch to apply.
|
| | |
|
| | |
|
| | |
|
| | |
|
| | |
|
| | |
|
| |
|
