diff options
Diffstat (limited to 'cpukit/score/cpu/m68k/rtems/m68k/qsm.h')
| -rw-r--r-- | cpukit/score/cpu/m68k/rtems/m68k/qsm.h | 209 |
1 files changed, 0 insertions, 209 deletions
diff --git a/cpukit/score/cpu/m68k/rtems/m68k/qsm.h b/cpukit/score/cpu/m68k/rtems/m68k/qsm.h deleted file mode 100644 index e1bf33bc12..0000000000 --- a/cpukit/score/cpu/m68k/rtems/m68k/qsm.h +++ /dev/null @@ -1,209 +0,0 @@ -/* - *------------------------------------------------------------------- - * - * QSM -- Queued Serial Module - * - * The QSM contains two serial interfaces: (a) the queued serial - * peripheral interface (QSPI) and the serial communication interface - * (SCI). The QSPI provides peripheral expansion and/or interprocessor - * communication through a full-duplex, synchronous, three-wire bus. A - * self contained RAM queue permits serial data transfers without CPU - * intervention and automatic continuous sampling. The SCI provides a - * standard non-return to zero mark/space format with wakeup functions - * to allow the CPU to run uninterrupted until woken - * - * For more information, refer to Motorola's "Modular Microcontroller - * Family Queued Serial Module Reference Manual" (Motorola document - * QSMRM/AD). - * - * This file has been created by John S. Gwynne for support of - * Motorola's 68332 MCU in the efi332 project. - * - * Redistribution and use in source and binary forms are permitted - * provided that the following conditions are met: - * 1. Redistribution of source code and documentation must retain - * the above authorship, this list of conditions and the - * following disclaimer. - * 2. The name of the author may not be used to endorse or promote - * products derived from this software without specific prior - * written permission. - * - * This software is provided "AS IS" without warranty of any kind, - * either expressed or implied, including, but not limited to, the - * implied warranties of merchantability, title and fitness for a - * particular purpose. - * - *------------------------------------------------------------------ - * - * $Id$ - */ - -#ifndef _QSM_H_ -#define _QSM_H_ - - -#include <efi332.h> - - -/* SAM-- shift and mask */ -#undef SAM -#define SAM(a,b,c) ((a << b) & c) - - -/* QSM_CRB (QSM Control Register Block) base address of the QSM - control registers */ -#if SIM_MM == 0 -#define QSM_CRB 0x7ffc00 -#else -#undef SIM_MM -#define SIM_MM 1 -#define QSM_CRB 0xfffc00 -#endif - - -#define QSMCR (volatile unsigned short int * const)(0x00 + QSM_CRB) - /* QSM Configuration Register */ -#define STOP 0x8000 /* Stop Enable */ -#define FRZ 0x6000 /* Freeze Control */ -#define SUPV 0x0080 /* Supervisor/Unrestricted */ -#define IARB 0x000f /* Inerrupt Arbitration */ - - -#define QTEST (volatile unsigned short int * const)(0x02 + QSM_CRB) - /* QSM Test Register */ -/* Used only for factor testing */ - - -#define QILR (volatile unsigned char * const)(0x04 + QSM_CRB) - /* QSM Interrupt Level Register */ -#define ILQSPI 0x38 /* Interrupt Level for QSPI */ -#define ILSCI 0x07 /* Interrupt Level for SCI */ - - -#define QIVR (volatile unsigned char * const)(0x05 + QSM_CRB) - /* QSM Interrupt Vector Register */ -#define INTV 0xff /* Interrupt Vector Number */ - - -#define SCCR0 (volatile unsigned short int * const)(0x08 + QSM_CRB) - /* SCI Control Register 0 */ -#define SCBR 0x1fff /* SCI Baud Rate */ - - -#define SCCR1 (volatile unsigned short int * const)(0x0a + QSM_CRB) - /* SCI Control Register 1 */ -#define LOOPS 0x4000 /* Loop Mode */ -#define WOMS 0x2000 /* Wired-OR Mode for SCI Pins */ -#define ILT 0x1000 /* Idle-Line Detect Type */ -#define PT 0x0800 /* Parity Type */ -#define PE 0x0400 /* Parity Enable */ -#define M 0x0200 /* Mode Select */ -#define WAKE 0x0100 /* Wakeup by Address Mark */ -#define TIE 0x0080 /* Transmit Complete Interrupt Enable */ -#define TCIE 0x0040 /* Transmit Complete Interrupt Enable */ -#define RIE 0x0020 /* Receiver Interrupt Enable */ -#define ILIE 0x0010 /* Idle-Line Interrupt Enable */ -#define TE 0x0008 /* Transmitter Enable */ -#define RE 0x0004 /* Receiver Enable */ -#define RWU 0x0002 /* Receiver Wakeup */ -#define SBK 0x0001 /* Send Break */ - - -#define SCSR (volatile unsigned short int * const)(0x0c + QSM_CRB) - /* SCI Status Register */ -#define TDRE 0x0100 /* Transmit Data Register Empty */ -#define TC 0x0080 /* Transmit Complete */ -#define RDRF 0x0040 /* Receive Data Register Full */ -#define RAF 0x0020 /* Receiver Active */ -#define IDLE 0x0010 /* Idle-Line Detected */ -#define OR 0x0008 /* Overrun Error */ -#define NF 0x0004 /* Noise Error Flag */ -#define FE 0x0002 /* Framing Error */ -#define PF 0x0001 /* Parity Error */ - - -#define SCDR (volatile unsigned short int * const)(0x0e + QSM_CRB) - /* SCI Data Register */ - - -#define PORTQS (volatile unsigned char * const)(0x15 + QSM_CRB) - /* Port QS Data Register */ - -#define PQSPAR (volatile unsigned char * const)(0x16 + QSM_CRB) - /* PORT QS Pin Assignment Rgister */ -/* Any bit cleared (zero) defines the corresponding pin to be an I/O - pin. Any bit set defines the corresponding pin to be a QSPI - signal. */ -/* note: PQS2 is a digital I/O pin unless the SPI is enabled in which - case it becomes the SPI serial clock SCK. */ -/* note: PQS7 is a digital I/O pin unless the SCI transmitter is - enabled in which case it becomes the SCI serial output TxD. */ -#define QSMFun 0x0 -#define QSMDis 0x1 -/* - * PQSPAR Field | QSM Function | Discrete I/O pin - *------------------+--------------+------------------ */ -#define PQSPA0 0 /* MISO | PQS0 */ -#define PQSPA1 1 /* MOSI | PQS1 */ -#define PQSPA2 2 /* SCK | PQS2 (see note)*/ -#define PQSPA3 3 /* PCSO/!SS | PQS3 */ -#define PQSPA4 4 /* PCS1 | PQS4 */ -#define PQSPA5 5 /* PCS2 | PQS5 */ -#define PQSPA6 6 /* PCS3 | PQS6 */ -#define PQSPA7 7 /* TxD | PQS7 (see note)*/ - - -#define DDRQS (volatile unsigned char * const)(0x17 + QSM_CRB) - /* PORT QS Data Direction Register */ -/* Clearing a bit makes the corresponding pin an input; setting a bit - makes the pin an output. */ - - -#define SPCR0 (volatile unsigned short int * const)(0x18 + QSM_CRB) - /* QSPI Control Register 0 */ -#define MSTR 0x8000 /* Master/Slave Mode Select */ -#define WOMQ 0x4000 /* Wired-OR Mode for QSPI Pins */ -#define BITS 0x3c00 /* Bits Per Transfer */ -#define CPOL 0x0200 /* Clock Polarity */ -#define CPHA 0x0100 /* Clock Phase */ -#define SPBR 0x00ff /* Serial Clock Baud Rate */ - - -#define SPCR1 (volatile unsigned short int * const)(0x1a + QSM_CRB) - /* QSPI Control Register 1 */ -#define SPE 0x8000 /* QSPI Enable */ -#define DSCKL 0x7f00 /* Delay before SCK */ -#define DTL 0x00ff /* Length of Delay after Transfer */ - - -#define SPCR2 (volatile unsigned short int * const)(0x1c + QSM_CRB) - /* QSPI Control Register 2 */ -#define SPIFIE 0x8000 /* SPI Finished Interrupt Enable */ -#define WREN 0x4000 /* Wrap Enable */ -#define WRTO 0x2000 /* Wrap To */ -#define ENDQP 0x0f00 /* Ending Queue Pointer */ -#define NEWQP 0x000f /* New Queue Pointer Value */ - - -#define SPCR3 (volatile unsigned char * const)(0x1e + QSM_CRB) - /* QSPI Control Register 3 */ -#define LOOPQ 0x0400 /* QSPI Loop Mode */ -#define HMIE 0x0200 /* HALTA and MODF Interrupt Enable */ -#define HALT 0x0100 /* Halt */ - - -#define SPSR (volatile unsigned char * const)(0x1f + QSM_CRB) - /* QSPI Status Register */ -#define SPIF 0x0080 /* QSPI Finished Flag */ -#define MODF 0x0040 /* Mode Fault Flag */ -#define HALTA 0x0020 /* Halt Acknowlwdge Flag */ -#define CPTQP x0000f /* Completed Queue Pointer */ - -#define QSPIRR (volatile unsigned char * const)(0x100 + QSM_CRB) - /* QSPI Receive Data RAM */ -#define QSPITR (volatile unsigned char * const)(0x120 + QSM_CRB) - /* QSPI Transmit Data RAM */ -#define QSPIcR (volatile unsigned char * const)(0x140 + QSM_CRB) - /* QSPI Command RAM */ - -#endif /* _QSM_H_ */ |