diff options
Diffstat (limited to 'c/src/lib/libbsp/powerpc/mvme2307/NOTES')
-rw-r--r-- | c/src/lib/libbsp/powerpc/mvme2307/NOTES | 180 |
1 files changed, 0 insertions, 180 deletions
diff --git a/c/src/lib/libbsp/powerpc/mvme2307/NOTES b/c/src/lib/libbsp/powerpc/mvme2307/NOTES deleted file mode 100644 index 4623e80fad..0000000000 --- a/c/src/lib/libbsp/powerpc/mvme2307/NOTES +++ /dev/null @@ -1,180 +0,0 @@ -This should run on Motorola MVME230x boards, where x is 5, 6, 7, -or 8 designating 16, 32, 64, or 128 MB of DRAM. It should also -work on MVME230x where x is 1, 2, 3, or 4 which is the same board -using a '603 instead of a '604 processor. RTEMS_CPU_MODEL would -need to change in make/custom/mvme2307.cfg. - -Application is linked to run from RAM. If running from ROM, it -will copy itself to RAM (0x4000) when it boots. PPCBUG should -be used to load a binary image from the TFTP host into location -0x4000, with an entry point at 0x401c. PPCBUG can be set to -autoboot the application from ROM. PPCBUG does all of the low -level setup of memory controllers and such on the board before -jumping into the RTEMS application. - -TODO: Data cache is not enabled. This BSP should probably -be part of the MCP750 BSP as much of the hardware here is -also on the MCP750 board. The dec21140 driver here is derived -from an early version from the MCP750 BSP, but has been -rewritten to use scatter/gather DMA and interrupts rather than -CPU copies and polling. This should be considered for merging -into to the MCP750 BSP. The interrupt conroller code needs to -be better integrated into RTEMS calls like the MCP750. The -BSP should probably be renamed to mvme230x. - ----------------------------------------------------------------------------- - -Building and loading an application: - -=============== (host) ======================================= -% make -% powerpc-rtems-objcopy --output-target=binary hello.exe /tftpboot/hello.bin - -=============== (target - run from RAM) ====================== -PPC1-Bug>niop -Controller LUN =00? -Device LUN =00? -Get/Put =G? -File Name =? hello.bin -Memory Address =00004000? -Length =00000000? -Byte Offset =00000000? - -Bytes Received =&140780, Bytes Loaded =&140780 -Bytes/Second =&140780, Elapsed Time =1 Second(s) -PPC1-Bug>go 401c -Effective address: 0000401C - - -*** HELLO WORLD TEST *** -Hello World -*** END OF HELLO WORLD TEST *** -PPC1-Bug> - -=============== (target - run from ROM) ====================== - -PPC1-Bug>niop -Controller LUN =00? -Device LUN =00? -Get/Put =G? -File Name =? hello.bin -Memory Address =00004000? -Length =00000000? -Byte Offset =00000000? - -Bytes Received =&140780, Bytes Loaded =&140780 -Bytes/Second =&140780, Elapsed Time =1 Second(s) - -PPC1-Bug>pflash 4000:28000 ff000000 -Source Starting/Ending Addresses =00004000/0002BFFF -Destination Starting/Ending Addresses =FF000000/FF027FFF -Number of Effective Bytes =00028000 (&163840) - -Program FLASH Memory (Y/N)? y -FLASH Memory Programming Complete - -(reset to boot into application) - ----------------------------------------------------------------------------- - -memory map: -0x00000000 - 0x03ffffff RAM -0x80000000 - 0xbf7fffff PCI I/O space -0xc0000000 - 0xfcffffff PCI memory space -0xfd000000 - 0xfdffffff PCI memory space -0xfe000000 - 0xfe7fffff PCI I/O space -0xfef80000 - 0xfef8ffff Falcon registers -0xfeff0000 - 0xfeffffff Raven registers -0xff000000 - 0xff3fffff ROM bank A - application -0xff800000 - 0xff8fffff ROM bank B - PPCBUG -0xfff00000 - 0xffffffff ROM bank A or B - ----------------------------------------------------------------------------- -Use the PPCBUG "env" command to configure the board: - -PPC1-Bug>env -Bug or System environment [B/S] = B? -Field Service Menu Enable [Y/N] = N? -Remote Start Method Switch [G/M/B/N] = B? -Probe System for Supported I/O Controllers [Y/N] = Y? -Auto-Initialize of NVRAM Header Enable [Y/N] = Y? -Network PReP-Boot Mode Enable [Y/N] = N? -Negate VMEbus SYSFAIL* Always [Y/N] = N? -SCSI Bus Reset on Debugger Startup [Y/N] = N? -Primary SCSI Bus Negotiations Type [A/S/N] = A? -Primary SCSI Data Bus Width [W/N] = N? -Secondary SCSI Identifier = "07"? -NVRAM Bootlist (GEV.fw-boot-path) Boot Enable [Y/N] = N? -NVRAM Bootlist (GEV.fw-boot-path) Boot at power-up only [Y/N] = N? -NVRAM Bootlist (GEV.fw-boot-path) Boot Abort Delay = 5? -Auto Boot Enable [Y/N] = N? -Auto Boot at power-up only [Y/N] = N? -Auto Boot Scan Enable [Y/N] = N? -Auto Boot Scan Device Type List = FDISK/CDROM/TAPE/HDISK/? -Auto Boot Controller LUN = 00? -Auto Boot Device LUN = 00? -Auto Boot Partition Number = 00? -Auto Boot Abort Delay = 7? -Auto Boot Default String [NULL for an empty string] = ? -ROM Boot Enable [Y/N] = Y? -ROM Boot at power-up only [Y/N] = N? -ROM Boot Enable search of VMEbus [Y/N] = N? -ROM Boot Abort Delay = 5? -ROM Boot Direct Starting Address = FF000000? -ROM Boot Direct Ending Address = FF3FFFFF? -Network Auto Boot Enable [Y/N] = N? -Network Auto Boot at power-up only [Y/N] = N? -Network Auto Boot Controller LUN = 00? -Network Auto Boot Device LUN = 00? -Network Auto Boot Abort Delay = 5? -Network Auto Boot Configuration Parameters Offset (NVRAM) = 00001000? -Memory Size Enable [Y/N] = Y? -Memory Size Starting Address = 00000000? -Memory Size Ending Address = 02000000? -DRAM Speed in NANO Seconds = 60? -ROM First Access Length (0 - 31) = 10? -ROM Next Access Length (0 - 15) = 0? -DRAM Parity Enable [On-Detection/Always/Never - O/A/N] = O? -L2Cache Parity Enable [On-Detection/Always/Never - O/A/N] = O? -PCI Interrupts Route Control Registers (PIRQ0/1/2/3) = 0A0B0E0F? -Serial Startup Code Master Enable [Y/N] = N? -Serial Startup Code LF Enable [Y/N] = N? -VME3PCI Master Master Enable [Y/N] = Y? -PCI Slave Image 0 Control = 00000000? -PCI Slave Image 0 Base Address Register = 00000000? -PCI Slave Image 0 Bound Address Register = 00000000? -PCI Slave Image 0 Translation Offset = 00000000? -PCI Slave Image 1 Control = C0820000? -PCI Slave Image 1 Base Address Register = 01000000? -PCI Slave Image 1 Bound Address Register = 20000000? -PCI Slave Image 1 Translation Offset = 00000000? -PCI Slave Image 2 Control = C0410000? -PCI Slave Image 2 Base Address Register = 20000000? -PCI Slave Image 2 Bound Address Register = 22000000? -PCI Slave Image 2 Translation Offset = D0000000? -PCI Slave Image 3 Control = C0400000? -PCI Slave Image 3 Base Address Register = 2FFF0000? -PCI Slave Image 3 Bound Address Register = 30000000? -PCI Slave Image 3 Translation Offset = D0000000? -VMEbus Slave Image 0 Control = E0F20000? -VMEbus Slave Image 0 Base Address Register = 00000000? -VMEbus Slave Image 0 Bound Address Register = 02000000? -VMEbus Slave Image 0 Translation Offset = 80000000? -VMEbus Slave Image 1 Control = 00000000? -VMEbus Slave Image 1 Base Address Register = 00000000? -VMEbus Slave Image 1 Bound Address Register = 00000000? -VMEbus Slave Image 1 Translation Offset = 00000000? -VMEbus Slave Image 2 Control = 00000000? -VMEbus Slave Image 2 Base Address Register = 00000000? -VMEbus Slave Image 2 Bound Address Register = 00000000? -VMEbus Slave Image 2 Translation Offset = 00000000? -VMEbus Slave Image 3 Control = 00000000? -VMEbus Slave Image 3 Base Address Register = 00000000? -VMEbus Slave Image 3 Bound Address Register = 00000000? -VMEbus Slave Image 3 Translation Offset = 00000000? -PCI Miscellaneous Register = 10000000? -Special PCI Slave Image Register = 00000000? -Master Control Register = 80C00000? -Miscellaneous Control Register = 52060000? -User AM Codes - |