1 files changed, 0 insertions, 92 deletions
diff --git a/c/src/lib/libbsp/powerpc/motorola_powerpc/BOOTING b/c/src/lib/libbsp/powerpc/motorola_powerpc/BOOTING
deleted file mode 100644
index 16adda28df..0000000000
--- a/c/src/lib/libbsp/powerpc/motorola_powerpc/BOOTING
+++ /dev/null
@@ -1,92 +0,0 @@
-This file documents the on board monitor (PPCBUG) configuration used
-to be able to boot the archives located in powerpc-rtems/c/mcp750/bin.
-This information was provided by Eric Valette <valette@crf.canon.fr>
-
-NOTE (by Till Straumann <strauman@slac.stanford.edu>, 2003):
-Apparently, PPCBug fails to shut down the network interface after
-loading an image. This means that the ethernet chip is still able
-to write into its descriptors and network buffer memory which
-can result in the loaded system to be corrupted if that system
-relocates itself!. The proper place to shut down the interface
-would be PPCBug itself or a 'PPCBug startup script' - unfortunately,
-PPCBug doesn't offer such a feature. Therefore, the bootloader
-is by default compiled with the
-#ifdef USE_PPCBUG
-compile-time option ENABLED. It will then use a PPCBug system
-call to shut down the ethernet chip during an early stage of
-the boot process.
-NOTE: THIS (i.e. the system call) WILL FAIL IF YOU USE SOFTWARE
-OTHER THAN PPCBUG TO BOOT THE BSP. In such a case, you must
-recompile with #undef USE_PPCBUG and make sure the ethernet
-interface is quiet by other means.
-
------------------------ ENV command--------------
-PPC1-Bug>env
-Bug or System environment [B/S] = B? 
-Field Service Menu Enable [Y/N] = N? 
-Probe System for Supported I/O Controllers [Y/N] = Y? 
-Auto-Initialize of NVRAM Header Enable [Y/N] = Y? 
-Network PReP-Boot Mode Enable [Y/N] = Y?                <====================
-SCSI Bus Reset on Debugger Startup [Y/N]   = N? 
-Primary SCSI Bus Negotiations Type [A/S/N] = A? 
-Primary SCSI Data Bus Width [W/N]          = N? 
-Secondary SCSI Identifier                  = "07"? 
-NVRAM Boot List (GEV.fw-boot-path) Boot Enable [Y/N]           = Y? 
-NVRAM Boot List (GEV.fw-boot-path) Boot at power-up only [Y/N] = Y? 
-NVRAM Boot List (GEV.fw-boot-path) Boot Abort Delay            = 5? 
-Auto Boot Enable [Y/N]           = Y? 
-Auto Boot at power-up only [Y/N] = Y? 
-Auto Boot Scan Enable [Y/N]      = Y? 
-Auto Boot Scan Device Type List  = FDISK/CDROM/TAPE/HDISK/? 
-Auto Boot Controller LUN   = 14? 
-Auto Boot Device LUN       = 40? 
-Auto Boot Partition Number = 03? 
-Auto Boot Abort Delay      = 7? 
-Auto Boot Default String [NULL for an empty string] = ? 
-ROM Boot Enable [Y/N]            = N? 
-ROM Boot at power-up only [Y/N]  = Y? 
-ROM Boot Abort Delay             = 5? 
-ROM Boot Direct Starting Address = FFF00000? 
-ROM Boot Direct Ending Address   = FFFFFFFC? 
-Network Auto Boot Enable [Y/N]           = N? 
-Network Auto Boot at power-up only [Y/N] = N? 
-Network Auto Boot Controller LUN = 00? 
-Network Auto Boot Device LUN     = 00? 
-Network Auto Boot Abort Delay    = 5? 
-Network Auto Boot Configuration Parameters Offset (NVRAM) = 00001000? 
-Memory Size Enable [Y/N]         = Y? 
-Memory Size Starting Address     = 00000000? 
-Memory Size Ending Address       = 02000000? 
-DRAM Speed in NANO Seconds       = 60? 
-ROM First Access Length (0 - 31) = 10? 
-ROM Next Access Length  (0 - 15) = 0? 
-DRAM Parity Enable [On-Detection/Always/Never - O/A/N]    = O? 
-L2Cache Parity Enable [On-Detection/Always/Never - O/A/N] = O? 
-PCI Interrupts Route Control Registers (PIRQ0/1/2/3) = 0A050000? 
-Serial Startup Code Master Enable [Y/N] = N? 
-Serial Startup Code LF Enable [Y/N] =     N? 
----------------------NIOT ---------------------------
-PPC1-Bug>niot
-Controller LUN =00? 
-Device LUN     =00? 
-Node Control Memory Address =03F9E000? 
-Client IP Address      =194.2.81.157? 
-Server IP Address      =194.2.81.241? 
-Subnet IP Address Mask =255.255.255.0? 
-Broadcast IP Address   =255.255.255.255? 
-Gateway IP Address     =194.2.81.254? 
-Boot File Name ("NULL" for None)     =debug-ppc? 
-Argument File Name ("NULL" for None) =? 
-Boot File Load Address         =001F0000? 
-Boot File Execution Address    =001F0000? 
-Boot File Execution Delay      =00000000? 
-Boot File Length               =00000000? 
-Boot File Byte Offset          =00000000? 
-BOOTP/RARP Request Retry       =05? 
-TFTP/ARP Request Retry         =05? 
-Trace Character Buffer Address =00000000? 
-BOOTP/RARP Request Control: Always/When-Needed (A/W)=W? 
-BOOTP/RARP Reply Update Control: Yes/No (Y/N)       =Y? 
---------------------------------------------------------
-
-