2 files changed, 0 insertions, 93 deletions
diff --git a/c/src/lib/libbsp/powerpc/dmv177/README b/c/src/lib/libbsp/powerpc/dmv177/README
deleted file mode 100644
index 0f00873225..0000000000
--- a/c/src/lib/libbsp/powerpc/dmv177/README
+++ /dev/null
@@ -1,49 +0,0 @@
-#
-#  $Id$
-#
-
-BSP NAME:           dmv177
-BOARD:              DY-4 DMV177
-BUS:                VMEBus
-CPU FAMILY:         powerpc
-CPU:                PowerPC 603e
-COPROCESSORS:       N/A
-MODE:               32 bit mode
-
-DEBUG MONITOR:      DY-4 General Purpose Monitor (GPM)
-
-PERIPHERALS
-===========
-TIMERS:             PPC internal Timebase register
-  RESOLUTION:         ???
-SERIAL PORTS:       2 RS-232 provided by a Exar 88681
-                    2 RS-422 provided by a Zilog Z8530
-REAL-TIME CLOCK:    PPC internal Decrementer register
-DMA:                none
-RTC:                Harris ICM7170
-VIDEO:              none
-SCSI:               QLogic FAS216 SCSI-2 (unsupported)
-NETWORKING:         National Semiconductor SONIC DP83932B (Ethernet)
-
-DRIVER INFORMATION
-==================
-CLOCK DRIVER:       PPC internal
-SHMSUPP:            N/A
-TIMER DRIVER:       PPC internal
-CONSOLE DRIVER:     Uses libchip drivers for Exar 88681 and Zilog Z8530.
-
-STDIO
-=====
-
-These are the default settings.
-
-PORT:               Console port 0
-ELECTRICAL:         RS-232
-BAUD:               9600
-BITS PER CHARACTER: 8
-PARITY:             N
-STOP BITS:          1
-
-Notes
-=====
-The console and real-time clock drivers use the libchip library.
diff --git a/c/src/lib/libbsp/powerpc/dmv177/README.net b/c/src/lib/libbsp/powerpc/dmv177/README.net
deleted file mode 100644
index b3ff231340..0000000000
--- a/c/src/lib/libbsp/powerpc/dmv177/README.net
+++ /dev/null
@@ -1,44 +0,0 @@
-#
-#  $Id$
-#
-
-Setting the Ethernet Hardware Address
-=====================================
-
-The hardware Ethernet address is not set at the factory.  It is the
-responsibility of the end-user to insure that it is set properly.
-This file describes the standard procedure recommended by DY-4 
-technical support for setting this address.  This procedure is 
-similar to that followed by VxWorks as documented in DY-4
-Document Number #807885.
-
-The hardware Ethernet address and OS configuration information
-must be stored in the SEEPROM non-volatile memory of the
-SVME/DMV-176/177. The Foundation Firmware (FFW) reserves the 
-first 256 bytes of the SEEPROM for its own use and the remaining
-remaining 256 bytes are available for OS specific information.
-
-Three bytes in the Serial EEPROM are used for the lowest three bytes
-of the hardware Ethernet address These should be set to the serial
-number of your SVME/DMV-176/177 card to ensure a unique Ethernet
-address on your network. The three high bytes are hard coded in the
-BSP and represent the vendor-specific Ethernet codes (0x00, 0x80, 0x7F).
-Together these six bytes form the target's Ethernet address.
-
-Address is of the form ...
-
-NOTE: The serial number is found on the packaging (box) that the
-board came in OR it is also located on the solder side of the board  and
-looks something like SERNO:XXXXXX.  It can not be determined dynamically
-by software.
-
-Prior to using the Ethernet controller on the SVME/DMV-176/177 for the
-first time, the Ethernet address bytes must be programmed into the
-Serial EEPROM on the target card.   The 'emm' (EEPROM Memory Modification)
-command in the General Purpose Monitor (GPM) can be used to do this.
-
-In this example we will assume that the serial number of the target card
-is 123456.
-
-
-