1 files changed, 0 insertions, 108 deletions
diff --git a/c/src/lib/libbsp/m68k/mvme136/timer/timer.c b/c/src/lib/libbsp/m68k/mvme136/timer/timer.c
deleted file mode 100644
index 8c3ecd45f2..0000000000
--- a/c/src/lib/libbsp/m68k/mvme136/timer/timer.c
+++ /dev/null
@@ -1,108 +0,0 @@
-/*  Timer_init()
- *
- *  This routine initializes the Z8036 timer on the MVME136 board.
- *
- *  Input parameters:  NONE
- *
- *  Output parameters:  NONE
- *
- *  NOTE: This routine will not work if the optimizer is enabled
- *        for some compilers.  The multiple writes to the Z8036
- *        may be optimized away.
- *
- *        It is important that the timer start/stop overhead be
- *        determined when porting or modifying this code.
- *
- *  COPYRIGHT (c) 1989, 1990, 1991, 1992, 1993, 1994.
- *  On-Line Applications Research Corporation (OAR).
- *  All rights assigned to U.S. Government, 1994.
- *
- *  This material may be reproduced by or for the U.S. Government pursuant
- *  to the copyright license under the clause at DFARS 252.227-7013.  This
- *  notice must appear in all copies of this file and its derivatives.
- *
- *  $Id$
- */
-
-
-#include <rtems.h>
-#include <bsp.h>
-#include <z8036.h>
-
-#define TIMER 0xfffb0000   /* address of Z8036 on MVME136 */
-
-int Ttimer_val;
-rtems_boolean Timer_driver_Find_average_overhead;
-
-rtems_isr timerisr();
-
-void Timer_initialize()
-{
-  (void) set_vector( timerisr, 66, 0 );       /* install ISR */
-
-  Ttimer_val = 0;                             /* clear timer ISR count */
-  Z8x36_WRITE( TIMER, MASTER_INTR, 0x01 ); /* reset */
-  Z8x36_WRITE( TIMER, MASTER_INTR, 0x00 ); /* clear reset */
-  Z8x36_WRITE( TIMER, MASTER_INTR, 0xe2 ); /* disable lower chain, no vec */
-                                           /*  set right justified addr */
-                                              /*  and master int enable */
-  Z8x36_WRITE( TIMER, CT1_MODE_SPEC,  0x80 ); /* T1 continuous, and   */
-                                              /* cycle/pulse output   */
-
-  *((rtems_unsigned16 *)0xfffb0016) = 0x0000; /* write countdown value */
-/*
-  Z8x36_WRITE( TIMER, CT1_TIME_CONST_MSB, 0x00 );
-  Z8x36_WRITE( TIMER, CT1_TIME_CONST_LSB, 0x00 );
-*/
-  Z8x36_WRITE( TIMER, MASTER_CFG,         0xc4 ); /* enable timer1        */
-
-  Z8x36_WRITE( TIMER, CT1_CMD_STATUS,     0xc6 ); /* set INTR enable (IE), */
-                                                 /*  trigger command      */
-                                                 /*  (TCB) and gate       */
-                                                 /* command (GCB) bits    */
-  *((rtems_unsigned8 *)0xfffb0038) &= 0xfd;      /* enable timer INTR on  */
-                                                 /*    VME controller     */
-}
-
-#define AVG_OVERHEAD      6  /* It typically takes 3.0 microseconds */
-                             /* (6 countdowns) to start/stop the timer. */
-#define LEAST_VALID       10 /* Don't trust a value lower than this */
-
-int Read_timer()
-{
-/*
-  rtems_unsigned8  msb, lsb;
-*/
-  rtems_unsigned32 remaining, total;
-
-  Z8x36_WRITE( TIMER, CT1_CMD_STATUS,  0xce ); /* read the counter value */
-remaining = 0xffff - *((rtems_unsigned16 *) 0xfffb0010);
-/*
-  Z8x36_READ(  TIMER, CT1_CUR_CNT_MSB, msb );
-  Z8x36_READ(  TIMER, CT1_CUR_CNT_LSB, lsb );
-
-  remaining = 0xffff - ((msb << 8) + lsb);
-*/
-  total = (Ttimer_val * 0x10000) + remaining;
-
-  if ( Timer_driver_Find_average_overhead == 1 )
-    return total;          /* in one-half microsecond units */
-
-  else {
-    if ( total < LEAST_VALID )
-      return 0;            /* below timer resolution */
-    return (total-AVG_OVERHEAD) >> 1;
-  }
-}
-
-rtems_status_code Empty_function( void )
-{
-  return RTEMS_SUCCESSFUL;
-}
-
-void Set_find_average_overhead(
-  rtems_boolean find_flag
-)
-{
-  Timer_driver_Find_average_overhead = find_flag;
-}