summaryrefslogtreecommitdiffstats
path: root/bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c
diff options
context:
space:
mode:
Diffstat (limited to 'bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c')
-rw-r--r--bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c3569
1 files changed, 1860 insertions, 1709 deletions
diff --git a/bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c b/bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c
index 8c95d707a0..60d1535d6a 100644
--- a/bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c
+++ b/bsps/arm/stm32h7/hal/stm32h7xx_hal_flash_ex.c
@@ -1,1713 +1,1864 @@
-/**
- ******************************************************************************
- * @file stm32h7xx_hal_flash_ex.c
- * @author MCD Application Team
- * @brief Extended FLASH HAL module driver.
- * This file provides firmware functions to manage the following
- * functionalities of the FLASH extension peripheral:
- * + Extended programming operations functions
- *
- @verbatim
- ==============================================================================
- ##### Flash Extension features #####
- ==============================================================================
-
- [..] Comparing to other previous devices, the FLASH interface for STM32H7xx
- devices contains the following additional features
-
- (+) Capacity up to 2 Mbyte with dual bank architecture supporting read-while-write
- capability (RWW)
- (+) Dual bank memory organization
- (+) PCROP protection for all banks
- (+) Global readout protection (RDP)
- (+) Write protection
- (+) Secure access only protection
- (+) Bank / register swapping
- (+) Cyclic Redundancy Check (CRC)
-
- ##### How to use this driver #####
- ==============================================================================
- [..] This driver provides functions to configure and program the FLASH memory
- of all STM32H7xx devices. It includes
- (#) FLASH Memory Erase functions:
- (++) Lock and Unlock the FLASH interface using HAL_FLASH_Unlock() and
- HAL_FLASH_Lock() functions
- (++) Erase function: Sector erase, bank erase and dual-bank mass erase
- (++) There are two modes of erase :
- (+++) Polling Mode using HAL_FLASHEx_Erase()
- (+++) Interrupt Mode using HAL_FLASHEx_Erase_IT()
-
- (#) Option Bytes Programming functions: Use HAL_FLASHEx_OBProgram() to:
- (++) Set/Reset the write protection per bank
- (++) Set the Read protection Level
- (++) Set the BOR level
- (++) Program the user Option Bytes
- (++) PCROP protection configuration and control per bank
- (++) Secure area configuration and control per bank
- (++) Core Boot address configuration
-
- (#) FLASH Memory Lock and unlock per Bank: HAL_FLASHEx_Lock_Bank1(), HAL_FLASHEx_Unlock_Bank1(),
- HAL_FLASHEx_Lock_Bank2() and HAL_FLASHEx_Unlock_Bank2() functions
-
- (#) FLASH CRC computation function: Use HAL_FLASHEx_ComputeCRC() to:
- (++) Enable CRC feature
- (++) Program the desired burst size
- (++) Define the user Flash Area on which the CRC has be computed
- (++) Perform the CRC computation
- (++) Disable CRC feature
-
- @endverbatim
- ******************************************************************************
- * @attention
- *
- * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics.
- * All rights reserved.</center></h2>
- *
- * This software component is licensed by ST under BSD 3-Clause license,
- * the "License"; You may not use this file except in compliance with the
- * License. You may obtain a copy of the License at:
- * opensource.org/licenses/BSD-3-Clause
- *
- ******************************************************************************
- */
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32h7xx_hal.h"
-
-/** @addtogroup STM32H7xx_HAL_Driver
- * @{
- */
-
-/** @defgroup FLASHEx FLASHEx
+/**
+ ******************************************************************************
+ * @file stm32h7xx_hal_flash_ex.c
+ * @author MCD Application Team
+ * @brief Extended FLASH HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the FLASH extension peripheral:
+ * + Extended programming operations functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### Flash Extension features #####
+ ==============================================================================
+
+ [..] Comparing to other previous devices, the FLASH interface for STM32H7xx
+ devices contains the following additional features
+
+ (+) Capacity up to 2 Mbyte with dual bank architecture supporting read-while-write
+ capability (RWW)
+ (+) Dual bank memory organization
+ (+) PCROP protection for all banks
+ (+) Global readout protection (RDP)
+ (+) Write protection
+ (+) Secure access only protection
+ (+) Bank / register swapping (when Dual-Bank)
+ (+) Cyclic Redundancy Check (CRC)
+
+ ##### How to use this driver #####
+ ==============================================================================
+ [..] This driver provides functions to configure and program the FLASH memory
+ of all STM32H7xx devices. It includes
+ (#) FLASH Memory Erase functions:
+ (++) Lock and Unlock the FLASH interface using HAL_FLASH_Unlock() and
+ HAL_FLASH_Lock() functions
+ (++) Erase function: Sector erase, bank erase and dual-bank mass erase
+ (++) There are two modes of erase :
+ (+++) Polling Mode using HAL_FLASHEx_Erase()
+ (+++) Interrupt Mode using HAL_FLASHEx_Erase_IT()
+
+ (#) Option Bytes Programming functions: Use HAL_FLASHEx_OBProgram() to:
+ (++) Set/Reset the write protection per bank
+ (++) Set the Read protection Level
+ (++) Set the BOR level
+ (++) Program the user Option Bytes
+ (++) PCROP protection configuration and control per bank
+ (++) Secure area configuration and control per bank
+ (++) Core Boot address configuration
+ (++) TCM / AXI shared RAM configuration
+ (++) CPU Frequency Boost configuration
+
+ (#) FLASH Memory Lock and unlock per Bank: HAL_FLASHEx_Lock_Bank1(), HAL_FLASHEx_Unlock_Bank1(),
+ HAL_FLASHEx_Lock_Bank2() and HAL_FLASHEx_Unlock_Bank2() functions
+
+ (#) FLASH CRC computation function: Use HAL_FLASHEx_ComputeCRC() to:
+ (++) Enable CRC feature
+ (++) Program the desired burst size
+ (++) Define the user Flash Area on which the CRC has be computed
+ (++) Perform the CRC computation
+ (++) Disable CRC feature
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.
+ *
+ * This software is licensed under terms that can be found in the LICENSE file in
+ * the root directory of this software component.
+ * If no LICENSE file comes with this software, it is provided AS-IS.
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32h7xx_hal.h"
+
+/** @addtogroup STM32H7xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup FLASHEx FLASHEx
* @ingroup RTEMSBSPsARMSTM32H7
- * @brief FLASH HAL Extension module driver
- * @{
- */
-
-#ifdef HAL_FLASH_MODULE_ENABLED
-
-/* Private typedef -----------------------------------------------------------*/
-/* Private define ------------------------------------------------------------*/
-/** @addtogroup FLASHEx_Private_Constants
- * @{
- */
-#define FLASH_TIMEOUT_VALUE 50000U /* 50 s */
-
-/**
- * @}
- */
-/* Private macro -------------------------------------------------------------*/
-/* Private variables ---------------------------------------------------------*/
-/* Private function prototypes -----------------------------------------------*/
-/** @defgroup FLASHEx_Private_Functions FLASHEx Private Functions
+ * @brief FLASH HAL Extension module driver
+ * @{
+ */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @addtogroup FLASHEx_Private_Constants
+ * @{
+ */
+#define FLASH_TIMEOUT_VALUE 50000U /* 50 s */
+
+/**
+ * @}
+ */
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup FLASHEx_Private_Functions FLASHEx Private Functions
* @ingroup RTEMSBSPsARMSTM32H7
- * @{
- */
-static void FLASH_MassErase(uint32_t VoltageRange, uint32_t Banks);
-static void FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks);
-static void FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Bank);
-static void FLASH_OB_GetWRP(uint32_t *WRPState, uint32_t *WRPSector, uint32_t Bank);
-static void FLASH_OB_RDPConfig(uint32_t RDPLevel);
-static uint32_t FLASH_OB_GetRDP(void);
-static void FLASH_OB_PCROPConfig(uint32_t PCROConfigRDP, uint32_t PCROPStartAddr, uint32_t PCROPEndAddr, uint32_t Banks);
-static void FLASH_OB_GetPCROP(uint32_t *PCROPConfig, uint32_t *PCROPStartAddr,uint32_t *PCROPEndAddr, uint32_t Bank);
-static void FLASH_OB_BOR_LevelConfig(uint32_t Level);
-static uint32_t FLASH_OB_GetBOR(void);
-static void FLASH_OB_UserConfig(uint32_t UserType, uint32_t UserConfig);
-static uint32_t FLASH_OB_GetUser(void);
-static void FLASH_OB_BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1);
-static void FLASH_OB_GetBootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1);
-static void FLASH_OB_SecureAreaConfig(uint32_t SecureAreaConfig, uint32_t SecureAreaStartAddr, uint32_t SecureAreaEndAddr, uint32_t Banks);
-static void FLASH_OB_GetSecureArea(uint32_t *SecureAreaConfig, uint32_t *SecureAreaStartAddr, uint32_t *SecureAreaEndAddr, uint32_t Bank);
-static void FLASH_CRC_AddSector(uint32_t Sector, uint32_t Bank);
-static void FLASH_CRC_SelectAddress(uint32_t CRCStartAddr, uint32_t CRCEndAddr, uint32_t Bank);
-
-#if defined (DUAL_CORE)
-static void FLASH_OB_CM4BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1);
-static void FLASH_OB_GetCM4BootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1);
-#endif /* DUAL_CORE */
-
-#if defined (FLASH_OTPBL_LOCKBL)
-static void FLASH_OB_OTP_LockConfig(uint32_t OTP_Block);
-static uint32_t FLASH_OB_OTP_GetLock(void);
-#endif /* FLASH_OTPBL_LOCKBL */
-/**
- * @}
- */
-
-/* Exported functions ---------------------------------------------------------*/
-/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions
+ * @{
+ */
+static void FLASH_MassErase(uint32_t VoltageRange, uint32_t Banks);
+static void FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks);
+static void FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Bank);
+static void FLASH_OB_GetWRP(uint32_t *WRPState, uint32_t *WRPSector, uint32_t Bank);
+static void FLASH_OB_RDPConfig(uint32_t RDPLevel);
+static uint32_t FLASH_OB_GetRDP(void);
+static void FLASH_OB_PCROPConfig(uint32_t PCROConfigRDP, uint32_t PCROPStartAddr, uint32_t PCROPEndAddr, uint32_t Banks);
+static void FLASH_OB_GetPCROP(uint32_t *PCROPConfig, uint32_t *PCROPStartAddr,uint32_t *PCROPEndAddr, uint32_t Bank);
+static void FLASH_OB_BOR_LevelConfig(uint32_t Level);
+static uint32_t FLASH_OB_GetBOR(void);
+static void FLASH_OB_UserConfig(uint32_t UserType, uint32_t UserConfig);
+static uint32_t FLASH_OB_GetUser(void);
+static void FLASH_OB_BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1);
+static void FLASH_OB_GetBootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1);
+static void FLASH_OB_SecureAreaConfig(uint32_t SecureAreaConfig, uint32_t SecureAreaStartAddr, uint32_t SecureAreaEndAddr, uint32_t Banks);
+static void FLASH_OB_GetSecureArea(uint32_t *SecureAreaConfig, uint32_t *SecureAreaStartAddr, uint32_t *SecureAreaEndAddr, uint32_t Bank);
+static void FLASH_CRC_AddSector(uint32_t Sector, uint32_t Bank);
+static void FLASH_CRC_SelectAddress(uint32_t CRCStartAddr, uint32_t CRCEndAddr, uint32_t Bank);
+
+#if defined (DUAL_CORE)
+static void FLASH_OB_CM4BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1);
+static void FLASH_OB_GetCM4BootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1);
+#endif /*DUAL_CORE*/
+
+#if defined (FLASH_OTPBL_LOCKBL)
+static void FLASH_OB_OTP_LockConfig(uint32_t OTP_Block);
+static uint32_t FLASH_OB_OTP_GetLock(void);
+#endif /* FLASH_OTPBL_LOCKBL */
+
+#if defined (FLASH_OPTSR2_TCM_AXI_SHARED)
+static void FLASH_OB_SharedRAM_Config(uint32_t SharedRamConfig);
+static uint32_t FLASH_OB_SharedRAM_GetConfig(void);
+#endif /* FLASH_OPTSR2_TCM_AXI_SHARED */
+
+#if defined (FLASH_OPTSR2_CPUFREQ_BOOST)
+static void FLASH_OB_CPUFreq_BoostConfig(uint32_t FreqBoost);
+static uint32_t FLASH_OB_CPUFreq_GetBoost(void);
+#endif /* FLASH_OPTSR2_CPUFREQ_BOOST */
+/**
+ * @}
+ */
+
+/* Exported functions ---------------------------------------------------------*/
+/** @defgroup FLASHEx_Exported_Functions FLASHEx Exported Functions
* @ingroup RTEMSBSPsARMSTM32H7
- * @{
- */
-
-/** @defgroup FLASHEx_Exported_Functions_Group1 Extended IO operation functions
+ * @{
+ */
+
+/** @defgroup FLASHEx_Exported_Functions_Group1 Extended IO operation functions
* @ingroup RTEMSBSPsARMSTM32H7
- * @brief Extended IO operation functions
- *
-@verbatim
- ===============================================================================
- ##### Extended programming operation functions #####
- ===============================================================================
- [..]
- This subsection provides a set of functions allowing to manage the Extension FLASH
- programming operations Operations.
-
-@endverbatim
- * @{
- */
-/**
- * @brief Perform a mass erase or erase the specified FLASH memory sectors
- * @param[in] pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
- * contains the configuration information for the erasing.
- *
- * @param[out] SectorError pointer to variable that contains the configuration
- * information on faulty sector in case of error (0xFFFFFFFF means that all
- * the sectors have been correctly erased)
- *
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *SectorError)
-{
- HAL_StatusTypeDef status = HAL_OK;
- uint32_t sector_index;
-
- /* Check the parameters */
- assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
- assert_param(IS_FLASH_BANK(pEraseInit->Banks));
-
- /* Process Locked */
- __HAL_LOCK(&pFlash);
-
- /* Reset error code */
- pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
-
- /* Wait for last operation to be completed on Bank1 */
- if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- }
-
- /* Wait for last operation to be completed on Bank2 */
- if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- }
-
- if(status == HAL_OK)
- {
- if(pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
- {
- /* Mass erase to be done */
- FLASH_MassErase(pEraseInit->VoltageRange, pEraseInit->Banks);
-
- /* Wait for last operation to be completed */
- if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- /* if the erase operation is completed, disable the Bank1 BER Bit */
- FLASH->CR1 &= (~FLASH_CR_BER);
- }
- if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- /* if the erase operation is completed, disable the Bank2 BER Bit */
- FLASH->CR2 &= (~FLASH_CR_BER);
- }
- }
- else
- {
- /*Initialization of SectorError variable*/
- *SectorError = 0xFFFFFFFFU;
-
- /* Erase by sector by sector to be done*/
- for(sector_index = pEraseInit->Sector; sector_index < (pEraseInit->NbSectors + pEraseInit->Sector); sector_index++)
- {
- FLASH_Erase_Sector(sector_index, pEraseInit->Banks, pEraseInit->VoltageRange);
-
- if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- /* Wait for last operation to be completed */
- status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1);
-
- /* If the erase operation is completed, disable the SER Bit */
- FLASH->CR1 &= (~(FLASH_CR_SER | FLASH_CR_SNB));
- }
- if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- /* Wait for last operation to be completed */
- status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2);
-
- /* If the erase operation is completed, disable the SER Bit */
- FLASH->CR2 &= (~(FLASH_CR_SER | FLASH_CR_SNB));
- }
-
- if(status != HAL_OK)
- {
- /* In case of error, stop erase procedure and return the faulty sector */
- *SectorError = sector_index;
- break;
- }
- }
- }
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(&pFlash);
-
- return status;
-}
-
-/**
- * @brief Perform a mass erase or erase the specified FLASH memory sectors with interrupt enabled
- * @param pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
- * contains the configuration information for the erasing.
- *
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit)
-{
- HAL_StatusTypeDef status = HAL_OK;
-
- /* Check the parameters */
- assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
- assert_param(IS_FLASH_BANK(pEraseInit->Banks));
-
- /* Process Locked */
- __HAL_LOCK(&pFlash);
-
- /* Reset error code */
- pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
-
- /* Wait for last operation to be completed */
- if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- }
-
- if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- }
-
- if (status != HAL_OK)
- {
- /* Process Unlocked */
- __HAL_UNLOCK(&pFlash);
- }
- else
- {
- if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- /* Enable End of Operation and Error interrupts for Bank 1 */
-#if defined (FLASH_CR_OPERRIE)
- __HAL_FLASH_ENABLE_IT_BANK1(FLASH_IT_EOP_BANK1 | FLASH_IT_WRPERR_BANK1 | FLASH_IT_PGSERR_BANK1 | \
- FLASH_IT_STRBERR_BANK1 | FLASH_IT_INCERR_BANK1 | FLASH_IT_OPERR_BANK1);
-#else
- __HAL_FLASH_ENABLE_IT_BANK1(FLASH_IT_EOP_BANK1 | FLASH_IT_WRPERR_BANK1 | FLASH_IT_PGSERR_BANK1 | \
- FLASH_IT_STRBERR_BANK1 | FLASH_IT_INCERR_BANK1);
-#endif /* FLASH_CR_OPERRIE */
- }
- if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- /* Enable End of Operation and Error interrupts for Bank 2 */
-#if defined (FLASH_CR_OPERRIE)
- __HAL_FLASH_ENABLE_IT_BANK2(FLASH_IT_EOP_BANK2 | FLASH_IT_WRPERR_BANK2 | FLASH_IT_PGSERR_BANK2 | \
- FLASH_IT_STRBERR_BANK2 | FLASH_IT_INCERR_BANK2 | FLASH_IT_OPERR_BANK2);
-#else
- __HAL_FLASH_ENABLE_IT_BANK2(FLASH_IT_EOP_BANK2 | FLASH_IT_WRPERR_BANK2 | FLASH_IT_PGSERR_BANK2 | \
- FLASH_IT_STRBERR_BANK2 | FLASH_IT_INCERR_BANK2);
-#endif /* FLASH_CR_OPERRIE */
- }
-
- if(pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
- {
- /*Mass erase to be done*/
- if(pEraseInit->Banks == FLASH_BANK_1)
- {
- pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE_BANK1;
- }
- else if(pEraseInit->Banks == FLASH_BANK_2)
- {
- pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE_BANK2;
- }
- else
- {
- pFlash.ProcedureOnGoing = FLASH_PROC_ALLBANK_MASSERASE;
- }
-
- FLASH_MassErase(pEraseInit->VoltageRange, pEraseInit->Banks);
- }
- else
- {
- /* Erase by sector to be done */
- if(pEraseInit->Banks == FLASH_BANK_1)
- {
- pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE_BANK1;
- }
- else
- {
- pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE_BANK2;
- }
-
- pFlash.NbSectorsToErase = pEraseInit->NbSectors;
- pFlash.Sector = pEraseInit->Sector;
- pFlash.VoltageForErase = pEraseInit->VoltageRange;
-
- /* Erase first sector and wait for IT */
- FLASH_Erase_Sector(pEraseInit->Sector, pEraseInit->Banks, pEraseInit->VoltageRange);
- }
- }
-
- return status;
-}
-
-/**
- * @brief Program option bytes
- * @param pOBInit pointer to an FLASH_OBInitStruct structure that
- * contains the configuration information for the programming.
- *
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
-{
- HAL_StatusTypeDef status;
-
- /* Check the parameters */
- assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
-
- /* Process Locked */
- __HAL_LOCK(&pFlash);
-
- /* Reset Error Code */
- pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
-
- /* Wait for last operation to be completed */
- if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- else if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
- {
- status = HAL_ERROR;
- }
- else
- {
- status = HAL_OK;
- }
-
- if(status == HAL_OK)
- {
- /*Write protection configuration*/
- if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
- {
- assert_param(IS_WRPSTATE(pOBInit->WRPState));
-
- if(pOBInit->WRPState == OB_WRPSTATE_ENABLE)
- {
- /*Enable of Write protection on the selected Sector*/
- FLASH_OB_EnableWRP(pOBInit->WRPSector,pOBInit->Banks);
- }
- else
- {
- /*Disable of Write protection on the selected Sector*/
- FLASH_OB_DisableWRP(pOBInit->WRPSector, pOBInit->Banks);
- }
- }
-
- /* Read protection configuration */
- if((pOBInit->OptionType & OPTIONBYTE_RDP) != 0U)
- {
- /* Configure the Read protection level */
- FLASH_OB_RDPConfig(pOBInit->RDPLevel);
- }
-
- /* User Configuration */
- if((pOBInit->OptionType & OPTIONBYTE_USER) != 0U)
- {
- /* Configure the user option bytes */
- FLASH_OB_UserConfig(pOBInit->USERType, pOBInit->USERConfig);
- }
-
- /* PCROP Configuration */
- if((pOBInit->OptionType & OPTIONBYTE_PCROP) != 0U)
- {
- assert_param(IS_FLASH_BANK(pOBInit->Banks));
-
- /*Configure the Proprietary code readout protection */
- FLASH_OB_PCROPConfig(pOBInit->PCROPConfig, pOBInit->PCROPStartAddr, pOBInit->PCROPEndAddr, pOBInit->Banks);
- }
-
- /* BOR Level configuration */
- if((pOBInit->OptionType & OPTIONBYTE_BOR) == OPTIONBYTE_BOR)
- {
- FLASH_OB_BOR_LevelConfig(pOBInit->BORLevel);
- }
-
-#if defined(DUAL_CORE)
- /* CM7 Boot Address configuration */
- if((pOBInit->OptionType & OPTIONBYTE_CM7_BOOTADD) == OPTIONBYTE_CM7_BOOTADD)
- {
- FLASH_OB_BootAddConfig(pOBInit->BootConfig, pOBInit->BootAddr0, pOBInit->BootAddr1);
- }
-
- /* CM4 Boot Address configuration */
- if((pOBInit->OptionType & OPTIONBYTE_CM4_BOOTADD) == OPTIONBYTE_CM4_BOOTADD)
- {
- FLASH_OB_CM4BootAddConfig(pOBInit->CM4BootConfig, pOBInit->CM4BootAddr0, pOBInit->CM4BootAddr1);
- }
-#else /* Single Core*/
- /* Boot Address configuration */
- if((pOBInit->OptionType & OPTIONBYTE_BOOTADD) == OPTIONBYTE_BOOTADD)
- {
- FLASH_OB_BootAddConfig(pOBInit->BootConfig, pOBInit->BootAddr0, pOBInit->BootAddr1);
- }
-#endif /*DUAL_CORE*/
-
- /* Secure area configuration */
- if((pOBInit->OptionType & OPTIONBYTE_SECURE_AREA) == OPTIONBYTE_SECURE_AREA)
- {
- FLASH_OB_SecureAreaConfig(pOBInit->SecureAreaConfig, pOBInit->SecureAreaStartAddr, pOBInit->SecureAreaEndAddr,pOBInit->Banks);
- }
-
-#if defined(FLASH_OTPBL_LOCKBL)
- /* OTP Block Lock configuration */
- if((pOBInit->OptionType & OPTIONBYTE_OTP_LOCK) == OPTIONBYTE_OTP_LOCK)
- {
- FLASH_OB_OTP_LockConfig(pOBInit->OTPBlockLock);
- }
-#endif /* FLASH_OTPBL_LOCKBL */
- }
-
- /* Process Unlocked */
- __HAL_UNLOCK(&pFlash);
-
- return status;
-}
-
-/**
- * @brief Get the Option byte configuration
- * @param pOBInit pointer to an FLASH_OBInitStruct structure that
- * contains the configuration information for the programming.
- * @note The parameter Banks of the pOBInit structure must be set exclusively to FLASH_BANK_1 or FLASH_BANK_2,
- * as this parameter is use to get the given Bank WRP, PCROP and secured area configuration.
- *
- * @retval None
- */
-void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit)
-{
- pOBInit->OptionType = (OPTIONBYTE_USER | OPTIONBYTE_RDP | OPTIONBYTE_BOR);
-
- /* Get Read protection level */
- pOBInit->RDPLevel = FLASH_OB_GetRDP();
-
- /* Get the user option bytes */
- pOBInit->USERConfig = FLASH_OB_GetUser();
-
- /*Get BOR Level*/
- pOBInit->BORLevel = FLASH_OB_GetBOR();
-
- if ((pOBInit->Banks == FLASH_BANK_1) || (pOBInit->Banks == FLASH_BANK_2))
- {
- pOBInit->OptionType |= (OPTIONBYTE_WRP | OPTIONBYTE_PCROP | OPTIONBYTE_SECURE_AREA);
-
- /* Get write protection on the selected area */
- FLASH_OB_GetWRP(&(pOBInit->WRPState), &(pOBInit->WRPSector), pOBInit->Banks);
-
- /* Get the Proprietary code readout protection */
- FLASH_OB_GetPCROP(&(pOBInit->PCROPConfig), &(pOBInit->PCROPStartAddr), &(pOBInit->PCROPEndAddr), pOBInit->Banks);
-
- /*Get Bank Secure area*/
- FLASH_OB_GetSecureArea(&(pOBInit->SecureAreaConfig), &(pOBInit->SecureAreaStartAddr), &(pOBInit->SecureAreaEndAddr), pOBInit->Banks);
- }
-
- /*Get Boot Address*/
- FLASH_OB_GetBootAdd(&(pOBInit->BootAddr0), &(pOBInit->BootAddr1));
-#if defined(DUAL_CORE)
- pOBInit->OptionType |= OPTIONBYTE_CM7_BOOTADD | OPTIONBYTE_CM4_BOOTADD;
-
- /*Get CM4 Boot Address*/
- FLASH_OB_GetCM4BootAdd(&(pOBInit->CM4BootAddr0), &(pOBInit->CM4BootAddr1));
-#else
- pOBInit->OptionType |= OPTIONBYTE_BOOTADD;
-#endif /*DUAL_CORE*/
-
-#if defined (FLASH_OTPBL_LOCKBL)
- pOBInit->OptionType |= OPTIONBYTE_OTP_LOCK;
-
- /* Get OTP Block Lock */
- pOBInit->OTPBlockLock = FLASH_OB_OTP_GetLock();
-#endif /* FLASH_OTPBL_LOCKBL */
-}
-
-/**
- * @brief Unlock the FLASH Bank1 control registers access
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_Unlock_Bank1(void)
-{
- if(READ_BIT(FLASH->CR1, FLASH_CR_LOCK) != 0U)
- {
- /* Authorize the FLASH Bank1 Registers access */
- WRITE_REG(FLASH->KEYR1, FLASH_KEY1);
- WRITE_REG(FLASH->KEYR1, FLASH_KEY2);
-
- /* Verify Flash Bank1 is unlocked */
- if (READ_BIT(FLASH->CR1, FLASH_CR_LOCK) != 0U)
- {
- return HAL_ERROR;
- }
- }
-
- return HAL_OK;
-}
-
-/**
- * @brief Locks the FLASH Bank1 control registers access
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_Lock_Bank1(void)
-{
- /* Set the LOCK Bit to lock the FLASH Bank1 Registers access */
- SET_BIT(FLASH->CR1, FLASH_CR_LOCK);
- return HAL_OK;
-}
-
-/**
- * @brief Unlock the FLASH Bank2 control registers access
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_Unlock_Bank2(void)
-{
- if(READ_BIT(FLASH->CR2, FLASH_CR_LOCK) != 0U)
- {
- /* Authorize the FLASH Bank2 Registers access */
- WRITE_REG(FLASH->KEYR2, FLASH_KEY1);
- WRITE_REG(FLASH->KEYR2, FLASH_KEY2);
-
- /* Verify Flash Bank1 is unlocked */
- if (READ_BIT(FLASH->CR2, FLASH_CR_LOCK) != 0U)
- {
- return HAL_ERROR;
- }
- }
-
- return HAL_OK;
-}
-
-/**
- * @brief Locks the FLASH Bank2 control registers access
- * @retval HAL Status
- */
-HAL_StatusTypeDef HAL_FLASHEx_Lock_Bank2(void)
-{
- /* Set the LOCK Bit to lock the FLASH Bank2 Registers access */
- SET_BIT(FLASH->CR2, FLASH_CR_LOCK);
- return HAL_OK;
-}
-
-/*
- * @brief Perform a CRC computation on the specified FLASH memory area
- * @param pCRCInit pointer to an FLASH_CRCInitTypeDef structure that
- * contains the configuration information for the CRC computation.
- * @note CRC computation uses CRC-32 (Ethernet) polynomial 0x4C11DB7
- * @note The application should avoid running a CRC on PCROP or secure-only
- * user Flash memory area since it may alter the expected CRC value.
- * A special error flag (CRC read error: CRCRDERR) can be used to
- * detect such a case.
- * @retval HAL Status
-*/
-HAL_StatusTypeDef HAL_FLASHEx_ComputeCRC(FLASH_CRCInitTypeDef *pCRCInit, uint32_t *CRC_Result)
-{
- HAL_StatusTypeDef status;
- uint32_t sector_index;
-
- /* Check the parameters */
- assert_param(IS_FLASH_BANK_EXCLUSIVE(pCRCInit->Bank));
- assert_param(IS_FLASH_TYPECRC(pCRCInit->TypeCRC));
-
- /* Wait for OB change operation to be completed */
- status = FLASH_OB_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
-
- if (status == HAL_OK)
- {
- if (pCRCInit->Bank == FLASH_BANK_1)
- {
- /* Enable CRC feature */
- FLASH->CR1 |= FLASH_CR_CRC_EN;
-
- /* Clear CRC flags in Status Register: CRC end of calculation and CRC read error */
- FLASH->CCR1 |= (FLASH_CCR_CLR_CRCEND | FLASH_CCR_CLR_CRCRDERR);
-
- /* Clear current CRC result, program burst size and define memory area on which CRC has to be computed */
- FLASH->CRCCR1 |= FLASH_CRCCR_CLEAN_CRC | pCRCInit->BurstSize | pCRCInit->TypeCRC;
-
- if (pCRCInit->TypeCRC == FLASH_CRC_SECTORS)
- {
- /* Clear sectors list */
- FLASH->CRCCR1 |= FLASH_CRCCR_CLEAN_SECT;
-
- /* Select CRC sectors */
- for(sector_index = pCRCInit->Sector; sector_index < (pCRCInit->NbSectors + pCRCInit->Sector); sector_index++)
- {
- FLASH_CRC_AddSector(sector_index, FLASH_BANK_1);
- }
- }
- else if (pCRCInit->TypeCRC == FLASH_CRC_BANK)
- {
- /* Enable Bank 1 CRC select bit */
- FLASH->CRCCR1 |= FLASH_CRCCR_ALL_BANK;
- }
- else
- {
- /* Select CRC start and end addresses */
- FLASH_CRC_SelectAddress(pCRCInit->CRCStartAddr, pCRCInit->CRCEndAddr, FLASH_BANK_1);
- }
-
- /* Start the CRC calculation */
- FLASH->CRCCR1 |= FLASH_CRCCR_START_CRC;
-
- /* Wait on CRC busy flag */
- status = FLASH_CRC_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1);
-
- /* Return CRC result */
- (*CRC_Result) = FLASH->CRCDATA;
-
- /* Disable CRC feature */
- FLASH->CR1 &= (~FLASH_CR_CRC_EN);
-
- /* Clear CRC flags */
- __HAL_FLASH_CLEAR_FLAG_BANK1(FLASH_FLAG_CRCEND_BANK1 | FLASH_FLAG_CRCRDERR_BANK1);
- }
- else
- {
- /* Enable CRC feature */
- FLASH->CR2 |= FLASH_CR_CRC_EN;
-
- /* Clear CRC flags in Status Register: CRC end of calculation and CRC read error */
- FLASH->CCR2 |= (FLASH_CCR_CLR_CRCEND | FLASH_CCR_CLR_CRCRDERR);
-
- /* Clear current CRC result, program burst size and define memory area on which CRC has to be computed */
- FLASH->CRCCR2 |= FLASH_CRCCR_CLEAN_CRC | pCRCInit->BurstSize | pCRCInit->TypeCRC;
-
- if (pCRCInit->TypeCRC == FLASH_CRC_SECTORS)
- {
- /* Clear sectors list */
- FLASH->CRCCR2 |= FLASH_CRCCR_CLEAN_SECT;
-
- /* Add CRC sectors */
- for(sector_index = pCRCInit->Sector; sector_index < (pCRCInit->NbSectors + pCRCInit->Sector); sector_index++)
- {
- FLASH_CRC_AddSector(sector_index, FLASH_BANK_2);
- }
- }
- else if (pCRCInit->TypeCRC == FLASH_CRC_BANK)
- {
- /* Enable Bank 2 CRC select bit */
- FLASH->CRCCR2 |= FLASH_CRCCR_ALL_BANK;
- }
- else
- {
- /* Select CRC start and end addresses */
- FLASH_CRC_SelectAddress(pCRCInit->CRCStartAddr, pCRCInit->CRCEndAddr, FLASH_BANK_2);
- }
-
- /* Start the CRC calculation */
- FLASH->CRCCR2 |= FLASH_CRCCR_START_CRC;
-
- /* Wait on CRC busy flag */
- status = FLASH_CRC_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2);
-
- /* Return CRC result */
- (*CRC_Result) = FLASH->CRCDATA;
-
- /* Disable CRC feature */
- FLASH->CR2 &= (~FLASH_CR_CRC_EN);
-
- /* Clear CRC flags */
- __HAL_FLASH_CLEAR_FLAG_BANK2(FLASH_FLAG_CRCEND_BANK2 | FLASH_FLAG_CRCRDERR_BANK2);
- }
- }
-
- return status;
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/* Private functions ---------------------------------------------------------*/
-
-/** @addtogroup FLASHEx_Private_Functions
- * @{
- */
-
-/**
- * @brief Mass erase of FLASH memory
- * @param VoltageRange The device program/erase parallelism.
- * This parameter can be one of the following values:
- * @arg FLASH_VOLTAGE_RANGE_1 : Flash program/erase by 8 bits
- * @arg FLASH_VOLTAGE_RANGE_2 : Flash program/erase by 16 bits
- * @arg FLASH_VOLTAGE_RANGE_3 : Flash program/erase by 32 bits
- * @arg FLASH_VOLTAGE_RANGE_4 : Flash program/erase by 64 bits
- *
- * @param Banks Banks to be erased
- * This parameter can be one of the following values:
- * @arg FLASH_BANK_1: Bank1 to be erased
- * @arg FLASH_BANK_2: Bank2 to be erased
- * @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased
- *
- * @retval HAL Status
- */
-static void FLASH_MassErase(uint32_t VoltageRange, uint32_t Banks)
-{
- /* Check the parameters */
-#if defined (FLASH_CR_PSIZE)
- assert_param(IS_VOLTAGERANGE(VoltageRange));
-#else
- UNUSED(VoltageRange);
-#endif /* FLASH_CR_PSIZE */
- assert_param(IS_FLASH_BANK(Banks));
-
- /* Flash Mass Erase */
- if((Banks & FLASH_BANK_BOTH) == FLASH_BANK_BOTH)
- {
-#if defined (FLASH_CR_PSIZE)
- /* Reset Program/erase VoltageRange for Bank1 and Bank2 */
- FLASH->CR1 &= (~FLASH_CR_PSIZE);
- FLASH->CR2 &= (~FLASH_CR_PSIZE);
-
- /* Set voltage range */
- FLASH->CR1 |= VoltageRange;
- FLASH->CR2 |= VoltageRange;
-#endif /* FLASH_CR_PSIZE */
-
- /* Set Mass Erase Bit */
- FLASH->OPTCR |= FLASH_OPTCR_MER;
- }
- else
- {
- /* Proceed to erase Flash Bank */
- if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
-#if defined (FLASH_CR_PSIZE)
- /* Set Program/erase VoltageRange for Bank1 */
- FLASH->CR1 &= (~FLASH_CR_PSIZE);
- FLASH->CR1 |= VoltageRange;
-#endif /* FLASH_CR_PSIZE */
-
- /* Erase Bank1 */
- FLASH->CR1 |= (FLASH_CR_BER | FLASH_CR_START);
- }
- if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
-#if defined (FLASH_CR_PSIZE)
- /* Set Program/erase VoltageRange for Bank2 */
- FLASH->CR2 &= (~FLASH_CR_PSIZE);
- FLASH->CR2 |= VoltageRange;
-#endif /* FLASH_CR_PSIZE */
-
- /* Erase Bank2 */
- FLASH->CR2 |= (FLASH_CR_BER | FLASH_CR_START);
- }
- }
-}
-
-/**
- * @brief Erase the specified FLASH memory sector
- * @param Sector FLASH sector to erase
- * This parameter can be a value of @ref FLASH_Sectors
- * @param Banks Banks to be erased
- * This parameter can be one of the following values:
- * @arg FLASH_BANK_1: Bank1 to be erased
- * @arg FLASH_BANK_2: Bank2 to be erased
- * @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased
- * @param VoltageRange The device program/erase parallelism.
- * This parameter can be one of the following values:
- * @arg FLASH_VOLTAGE_RANGE_1 : Flash program/erase by 8 bits
- * @arg FLASH_VOLTAGE_RANGE_2 : Flash program/erase by 16 bits
- * @arg FLASH_VOLTAGE_RANGE_3 : Flash program/erase by 32 bits
- * @arg FLASH_VOLTAGE_RANGE_4 : Flash program/erase by 64 bits
- *
- * @retval None
- */
-void FLASH_Erase_Sector(uint32_t Sector, uint32_t Banks, uint32_t VoltageRange)
-{
- assert_param(IS_FLASH_SECTOR(Sector));
- assert_param(IS_FLASH_BANK_EXCLUSIVE(Banks));
-#if defined (FLASH_CR_PSIZE)
- assert_param(IS_VOLTAGERANGE(VoltageRange));
-#else
- UNUSED(VoltageRange);
-#endif /* FLASH_CR_PSIZE */
-
- if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
-#if defined (FLASH_CR_PSIZE)
- /* Reset Program/erase VoltageRange and Sector Number for Bank1 */
- FLASH->CR1 &= ~(FLASH_CR_PSIZE | FLASH_CR_SNB);
-
- FLASH->CR1 |= (FLASH_CR_SER | VoltageRange | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
-#else
- /* Reset Sector Number for Bank1 */
- FLASH->CR1 &= ~(FLASH_CR_SNB);
-
- FLASH->CR1 |= (FLASH_CR_SER | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
-#endif /* FLASH_CR_PSIZE */
- }
-
- if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
-#if defined (FLASH_CR_PSIZE)
- /* Reset Program/erase VoltageRange and Sector Number for Bank2 */
- FLASH->CR2 &= ~(FLASH_CR_PSIZE | FLASH_CR_SNB);
-
- FLASH->CR2 |= (FLASH_CR_SER | VoltageRange | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
-#else
- /* Reset Sector Number for Bank2 */
- FLASH->CR2 &= ~(FLASH_CR_SNB);
-
- FLASH->CR2 |= (FLASH_CR_SER | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
-#endif /* FLASH_CR_PSIZE */
- }
-}
-
-/**
- * @brief Enable the write protection of the desired bank1 or bank 2 sectors
- * @param WRPSector specifies the sector(s) to be write protected.
- * This parameter can be one of the following values:
- * @arg WRPSector: A combination of OB_WRP_SECTOR_0 to OB_WRP_SECTOR_7 or OB_WRP_SECTOR_All
- *
- * @param Banks the specific bank to apply WRP sectors
- * This parameter can be one of the following values:
- * @arg FLASH_BANK_1: enable WRP on specified bank1 sectors
- * @arg FLASH_BANK_2: enable WRP on specified bank2 sectors
- * @arg FLASH_BANK_BOTH: enable WRP on both bank1 and bank2 specified sectors
- *
- * @retval HAL FLASH State
- */
-static void FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks)
-{
- /* Check the parameters */
- assert_param(IS_OB_WRP_SECTOR(WRPSector));
- assert_param(IS_FLASH_BANK(Banks));
-
- if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- /* Enable Write Protection for bank 1 */
- FLASH->WPSN_PRG1 &= (~(WRPSector & FLASH_WPSN_WRPSN));
- }
-
- if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- /* Enable Write Protection for bank 2 */
- FLASH->WPSN_PRG2 &= (~(WRPSector & FLASH_WPSN_WRPSN));
- }
-}
-
-/**
- * @brief Disable the write protection of the desired bank1 or bank 2 sectors
- * @param WRPSector specifies the sector(s) to disable write protection.
- * This parameter can be one of the following values:
- * @arg WRPSector: A combination of FLASH_OB_WRP_SECTOR_0 to FLASH_OB_WRP_SECTOR_7 or FLASH_OB_WRP_SECTOR_All
- *
- * @param Banks the specific bank to apply WRP sectors
- * This parameter can be one of the following values:
- * @arg FLASH_BANK_1: disable WRP on specified bank1 sectors
- * @arg FLASH_BANK_2: disable WRP on specified bank2 sectors
- * @arg FLASH_BANK_BOTH: disable WRP on both bank1 and bank2 specified sectors
- *
- * @retval HAL FLASH State
- */
-static void FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Banks)
-{
- /* Check the parameters */
- assert_param(IS_OB_WRP_SECTOR(WRPSector));
- assert_param(IS_FLASH_BANK(Banks));
-
- if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- /* Disable Write Protection for bank 1 */
- FLASH->WPSN_PRG1 |= (WRPSector & FLASH_WPSN_WRPSN);
- }
-
- if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- /* Disable Write Protection for bank 2 */
- FLASH->WPSN_PRG2 |= (WRPSector & FLASH_WPSN_WRPSN);
- }
-}
-
-/**
- * @brief Get the write protection of the given bank 1 or bank 2 sectors
- * @param WRPState gives the write protection state on the given bank.
- * This parameter can be one of the following values:
- * @arg WRPState: OB_WRPSTATE_DISABLE or OB_WRPSTATE_ENABLE
-
- * @param WRPSector gives the write protected sector(s) on the given bank .
- * This parameter can be one of the following values:
- * @arg WRPSector: A combination of FLASH_OB_WRP_SECTOR_0 to FLASH_OB_WRP_SECTOR_7 or FLASH_OB_WRP_SECTOR_All
- *
- * @param Bank the specific bank to apply WRP sectors
- * This parameter can be exclusively one of the following values:
- * @arg FLASH_BANK_1: Get bank1 WRP sectors
- * @arg FLASH_BANK_2: Get bank2 WRP sectors
- * @arg FLASH_BANK_BOTH: note allowed in this functions
- *
- * @retval HAL FLASH State
- */
-static void FLASH_OB_GetWRP(uint32_t *WRPState, uint32_t *WRPSector, uint32_t Bank)
-{
- uint32_t regvalue = 0U;
-
- if((Bank & FLASH_BANK_BOTH) == FLASH_BANK_1)
- {
- regvalue = FLASH->WPSN_CUR1;
- }
-
- if((Bank & FLASH_BANK_BOTH) == FLASH_BANK_2)
- {
- regvalue = FLASH->WPSN_CUR2;
- }
-
- (*WRPSector) = (~regvalue) & FLASH_WPSN_WRPSN;
-
- if(*WRPSector == 0U)
- {
- (*WRPState) = OB_WRPSTATE_DISABLE;
- }
- else
- {
- (*WRPState) = OB_WRPSTATE_ENABLE;
- }
-}
-
-/**
- * @brief Set the read protection level.
- *
- * @note To configure the RDP level, the option lock bit OPTLOCK must be
- * cleared with the call of the HAL_FLASH_OB_Unlock() function.
- * @note To validate the RDP level, the option bytes must be reloaded
- * through the call of the HAL_FLASH_OB_Launch() function.
- * @note !!! Warning : When enabling OB_RDP level 2 it's no more possible
- * to go back to level 1 or 0 !!!
- *
- * @param RDPLevel specifies the read protection level.
- * This parameter can be one of the following values:
- * @arg OB_RDP_LEVEL_0: No protection
- * @arg OB_RDP_LEVEL_1: Read protection of the memory
- * @arg OB_RDP_LEVEL_2: Full chip protection
- *
- * @retval HAL status
- */
-static void FLASH_OB_RDPConfig(uint32_t RDPLevel)
-{
- /* Check the parameters */
- assert_param(IS_OB_RDP_LEVEL(RDPLevel));
-
- /* Configure the RDP level in the option bytes register */
- MODIFY_REG(FLASH->OPTSR_PRG, FLASH_OPTSR_RDP, RDPLevel);
-}
-
-/**
- * @brief Get the read protection level.
- * @retval RDPLevel specifies the read protection level.
- * This return value can be one of the following values:
- * @arg OB_RDP_LEVEL_0: No protection
- * @arg OB_RDP_LEVEL_1: Read protection of the memory
- * @arg OB_RDP_LEVEL_2: Full chip protection
- */
-static uint32_t FLASH_OB_GetRDP(void)
-{
- uint32_t rdp_level = READ_BIT(FLASH->OPTSR_CUR, FLASH_OPTSR_RDP);
-
- if ((rdp_level != OB_RDP_LEVEL_0) && (rdp_level != OB_RDP_LEVEL_2))
- {
- return (OB_RDP_LEVEL_1);
- }
- else
- {
- return rdp_level;
- }
-}
-
-#if defined(DUAL_CORE)
-/**
- * @brief Program the FLASH User Option Byte.
- *
- * @note To configure the user option bytes, the option lock bit OPTLOCK must
- * be cleared with the call of the HAL_FLASH_OB_Unlock() function.
- *
- * @note To validate the user option bytes, the option bytes must be reloaded
- * through the call of the HAL_FLASH_OB_Launch() function.
- *
- * @param UserType The FLASH User Option Bytes to be modified :
- * a combination of @ref FLASHEx_OB_USER_Type
- *
- * @param UserConfig The FLASH User Option Bytes values:
- * IWDG1_SW(Bit4), IWDG2_SW(Bit 5), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
- * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
- * SECURITY(Bit 21), BCM4(Bit 22), BCM7(Bit 23), nRST_STOP_D2(Bit 24),
- * nRST_STDY_D2(Bit 25), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
- *
- * @retval HAL status
- */
-#else
-/**
- * @brief Program the FLASH User Option Byte.
- *
- * @note To configure the user option bytes, the option lock bit OPTLOCK must
- * be cleared with the call of the HAL_FLASH_OB_Unlock() function.
- *
- * @note To validate the user option bytes, the option bytes must be reloaded
- * through the call of the HAL_FLASH_OB_Launch() function.
- *
- * @param UserType The FLASH User Option Bytes to be modified :
- * a combination of @arg FLASHEx_OB_USER_Type
- *
- * @param UserConfig The FLASH User Option Bytes values:
- * IWDG_SW(Bit4), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
- * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
- * SECURITY(Bit 21), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
- *
- * @retval HAL status
- */
-#endif /*DUAL_CORE*/
-static void FLASH_OB_UserConfig(uint32_t UserType, uint32_t UserConfig)
-{
- uint32_t optr_reg_val = 0;
- uint32_t optr_reg_mask = 0;
-
- /* Check the parameters */
- assert_param(IS_OB_USER_TYPE(UserType));
-
- if((UserType & OB_USER_IWDG1_SW) != 0U)
- {
- /* IWDG_HW option byte should be modified */
- assert_param(IS_OB_IWDG1_SOURCE(UserConfig & FLASH_OPTSR_IWDG1_SW));
-
- /* Set value and mask for IWDG_HW option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_IWDG1_SW);
- optr_reg_mask |= FLASH_OPTSR_IWDG1_SW;
- }
-#if defined(DUAL_CORE)
- if((UserType & OB_USER_IWDG2_SW) != 0U)
- {
- /* IWDG2_SW option byte should be modified */
- assert_param(IS_OB_IWDG2_SOURCE(UserConfig & FLASH_OPTSR_IWDG2_SW));
-
- /* Set value and mask for IWDG2_SW option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_IWDG2_SW);
- optr_reg_mask |= FLASH_OPTSR_IWDG2_SW;
- }
-#endif /*DUAL_CORE*/
- if((UserType & OB_USER_NRST_STOP_D1) != 0U)
- {
- /* NRST_STOP option byte should be modified */
- assert_param(IS_OB_STOP_D1_RESET(UserConfig & FLASH_OPTSR_NRST_STOP_D1));
-
- /* Set value and mask for NRST_STOP option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STOP_D1);
- optr_reg_mask |= FLASH_OPTSR_NRST_STOP_D1;
- }
-
- if((UserType & OB_USER_NRST_STDBY_D1) != 0U)
- {
- /* NRST_STDBY option byte should be modified */
- assert_param(IS_OB_STDBY_D1_RESET(UserConfig & FLASH_OPTSR_NRST_STBY_D1));
-
- /* Set value and mask for NRST_STDBY option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STBY_D1);
- optr_reg_mask |= FLASH_OPTSR_NRST_STBY_D1;
- }
-
- if((UserType & OB_USER_IWDG_STOP) != 0U)
- {
- /* IWDG_STOP option byte should be modified */
- assert_param(IS_OB_USER_IWDG_STOP(UserConfig & FLASH_OPTSR_FZ_IWDG_STOP));
-
- /* Set value and mask for IWDG_STOP option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_FZ_IWDG_STOP);
- optr_reg_mask |= FLASH_OPTSR_FZ_IWDG_STOP;
- }
-
- if((UserType & OB_USER_IWDG_STDBY) != 0U)
- {
- /* IWDG_STDBY option byte should be modified */
- assert_param(IS_OB_USER_IWDG_STDBY(UserConfig & FLASH_OPTSR_FZ_IWDG_SDBY));
-
- /* Set value and mask for IWDG_STDBY option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_FZ_IWDG_SDBY);
- optr_reg_mask |= FLASH_OPTSR_FZ_IWDG_SDBY;
- }
-
- if((UserType & OB_USER_ST_RAM_SIZE) != 0U)
- {
- /* ST_RAM_SIZE option byte should be modified */
- assert_param(IS_OB_USER_ST_RAM_SIZE(UserConfig & FLASH_OPTSR_ST_RAM_SIZE));
-
- /* Set value and mask for ST_RAM_SIZE option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_ST_RAM_SIZE);
- optr_reg_mask |= FLASH_OPTSR_ST_RAM_SIZE;
- }
-
- if((UserType & OB_USER_SECURITY) != 0U)
- {
- /* SECURITY option byte should be modified */
- assert_param(IS_OB_USER_SECURITY(UserConfig & FLASH_OPTSR_SECURITY));
-
- /* Set value and mask for SECURITY option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_SECURITY);
- optr_reg_mask |= FLASH_OPTSR_SECURITY;
- }
-
-#if defined(DUAL_CORE)
- if((UserType & OB_USER_BCM4) != 0U)
- {
- /* BCM4 option byte should be modified */
- assert_param(IS_OB_USER_BCM4(UserConfig & FLASH_OPTSR_BCM4));
-
- /* Set value and mask for BCM4 option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_BCM4);
- optr_reg_mask |= FLASH_OPTSR_BCM4;
- }
-
- if((UserType & OB_USER_BCM7) != 0U)
- {
- /* BCM7 option byte should be modified */
- assert_param(IS_OB_USER_BCM7(UserConfig & FLASH_OPTSR_BCM7));
-
- /* Set value and mask for BCM7 option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_BCM7);
- optr_reg_mask |= FLASH_OPTSR_BCM7;
- }
-
- if((UserType & OB_USER_NRST_STOP_D2) != 0U)
- {
- /* NRST_STOP option byte should be modified */
- assert_param(IS_OB_STOP_D2_RESET(UserConfig & FLASH_OPTSR_NRST_STOP_D2));
-
- /* Set value and mask for NRST_STOP option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STOP_D2);
- optr_reg_mask |= FLASH_OPTSR_NRST_STOP_D2;
- }
-
- if((UserType & OB_USER_NRST_STDBY_D2) != 0U)
- {
- /* NRST_STDBY option byte should be modified */
- assert_param(IS_OB_STDBY_D2_RESET(UserConfig & FLASH_OPTSR_NRST_STBY_D2));
-
- /* Set value and mask for NRST_STDBY option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STBY_D2);
- optr_reg_mask |= FLASH_OPTSR_NRST_STBY_D2;
- }
-#endif /* DUAL_CORE */
- if((UserType & OB_USER_SWAP_BANK) != 0U)
- {
- /* SWAP_BANK_OPT option byte should be modified */
- assert_param(IS_OB_USER_SWAP_BANK(UserConfig & FLASH_OPTSR_SWAP_BANK_OPT));
-
- /* Set value and mask for SWAP_BANK_OPT option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_SWAP_BANK_OPT);
- optr_reg_mask |= FLASH_OPTSR_SWAP_BANK_OPT;
- }
-
- if((UserType & OB_USER_IOHSLV) != 0U)
- {
- /* IOHSLV_OPT option byte should be modified */
- assert_param(IS_OB_USER_IOHSLV(UserConfig & FLASH_OPTSR_IO_HSLV));
-
- /* Set value and mask for IOHSLV_OPT option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_IO_HSLV);
- optr_reg_mask |= FLASH_OPTSR_IO_HSLV;
- }
-
-#if defined (FLASH_OPTSR_VDDMMC_HSLV)
- if((UserType & OB_USER_VDDMMC_HSLV) != 0U)
- {
- /* VDDMMC_HSLV option byte should be modified */
- assert_param(IS_OB_USER_VDDMMC_HSLV(UserConfig & FLASH_OPTSR_VDDMMC_HSLV));
-
- /* Set value and mask for VDDMMC_HSLV option byte */
- optr_reg_val |= (UserConfig & FLASH_OPTSR_VDDMMC_HSLV);
- optr_reg_mask |= FLASH_OPTSR_VDDMMC_HSLV;
- }
-#endif /* FLASH_OPTSR_VDDMMC_HSLV */
-
- /* Configure the option bytes register */
- MODIFY_REG(FLASH->OPTSR_PRG, optr_reg_mask, optr_reg_val);
-}
-
-#if defined(DUAL_CORE)
-/**
- * @brief Return the FLASH User Option Byte value.
- * @retval The FLASH User Option Bytes values
- * IWDG1_SW(Bit4), IWDG2_SW(Bit 5), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
- * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
- * SECURITY(Bit 21), BCM4(Bit 22), BCM7(Bit 23), nRST_STOP_D2(Bit 24),
- * nRST_STDY_D2(Bit 25), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
- */
-#else
-/**
- * @brief Return the FLASH User Option Byte value.
- * @retval The FLASH User Option Bytes values
- * IWDG_SW(Bit4), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
- * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
- * SECURITY(Bit 21), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
- */
-#endif /*DUAL_CORE*/
-static uint32_t FLASH_OB_GetUser(void)
-{
- uint32_t userConfig = READ_REG(FLASH->OPTSR_CUR);
- userConfig &= (~(FLASH_OPTSR_BOR_LEV | FLASH_OPTSR_RDP));
-
- return userConfig;
-}
-
-/**
- * @brief Configure the Proprietary code readout protection of the desired addresses
- *
- * @note To configure the PCROP options, the option lock bit OPTLOCK must be
- * cleared with the call of the HAL_FLASH_OB_Unlock() function.
- * @note To validate the PCROP options, the option bytes must be reloaded
- * through the call of the HAL_FLASH_OB_Launch() function.
- *
- * @param PCROPConfig specifies if the PCROP area for the given Bank shall be erased or not
- * when RDP level decreased from Level 1 to Level 0, or after a bank erase with protection removal
- * This parameter must be a value of @arg FLASHEx_OB_PCROP_RDP enumeration
- *
- * @param PCROPStartAddr specifies the start address of the Proprietary code readout protection
- * This parameter can be an address between begin and end of the bank
- *
- * @param PCROPEndAddr specifies the end address of the Proprietary code readout protection
- * This parameter can be an address between PCROPStartAddr and end of the bank
- *
- * @param Banks the specific bank to apply PCROP protection
- * This parameter can be one of the following values:
- * @arg FLASH_BANK_1: PCROP on specified bank1 area
- * @arg FLASH_BANK_2: PCROP on specified bank2 area
- * @arg FLASH_BANK_BOTH: PCROP on specified bank1 and bank2 area (same config will be applied on both banks)
- *
- * @retval None
- */
-static void FLASH_OB_PCROPConfig(uint32_t PCROPConfig, uint32_t PCROPStartAddr, uint32_t PCROPEndAddr, uint32_t Banks)
-{
- /* Check the parameters */
- assert_param(IS_FLASH_BANK(Banks));
- assert_param(IS_OB_PCROP_RDP(PCROPConfig));
-
- if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(PCROPStartAddr));
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(PCROPEndAddr));
-
- /* Configure the Proprietary code readout protection */
- FLASH->PRAR_PRG1 = ((PCROPStartAddr - FLASH_BANK1_BASE) >> 8) | \
- (((PCROPEndAddr - FLASH_BANK1_BASE) >> 8) << FLASH_PRAR_PROT_AREA_END_Pos) | \
- PCROPConfig;
- }
-
- if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(PCROPStartAddr));
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(PCROPEndAddr));
-
- /* Configure the Proprietary code readout protection */
- FLASH->PRAR_PRG2 = ((PCROPStartAddr - FLASH_BANK2_BASE) >> 8) | \
- (((PCROPEndAddr - FLASH_BANK2_BASE) >> 8) << FLASH_PRAR_PROT_AREA_END_Pos) | \
- PCROPConfig;
- }
-}
-
-/**
- * @brief Get the Proprietary code readout protection configuration on a given Bank
- *
- * @param PCROPConfig indicates if the PCROP area for the given Bank shall be erased or not
- * when RDP level decreased from Level 1 to Level 0 or after a bank erase with protection removal
- *
- * @param PCROPStartAddr gives the start address of the Proprietary code readout protection of the bank
- *
- * @param PCROPEndAddr gives the end address of the Proprietary code readout protection of the bank
- *
- * @param Bank the specific bank to apply PCROP protection
- * This parameter can be exclusively one of the following values:
- * @arg FLASH_BANK_1: PCROP on specified bank1 area
- * @arg FLASH_BANK_2: PCROP on specified bank2 area
- * @arg FLASH_BANK_BOTH: is not allowed here
- *
- * @retval None
- */
-static void FLASH_OB_GetPCROP(uint32_t *PCROPConfig, uint32_t *PCROPStartAddr, uint32_t *PCROPEndAddr, uint32_t Bank)
-{
- uint32_t regvalue = 0;
- uint32_t bankBase = 0;
-
- if((Bank & FLASH_BANK_BOTH) == FLASH_BANK_1)
- {
- regvalue = FLASH->PRAR_CUR1;
- bankBase = FLASH_BANK1_BASE;
- }
-
- if((Bank & FLASH_BANK_BOTH) == FLASH_BANK_2)
- {
- regvalue = FLASH->PRAR_CUR2;
- bankBase = FLASH_BANK2_BASE;
- }
-
- (*PCROPConfig) = (regvalue & FLASH_PRAR_DMEP);
-
- (*PCROPStartAddr) = ((regvalue & FLASH_PRAR_PROT_AREA_START) << 8) + bankBase;
- (*PCROPEndAddr) = (regvalue & FLASH_PRAR_PROT_AREA_END) >> FLASH_PRAR_PROT_AREA_END_Pos;
- (*PCROPEndAddr) = ((*PCROPEndAddr) << 8) + bankBase;
-}
-
-/**
- * @brief Set the BOR Level.
- * @param Level specifies the Option Bytes BOR Reset Level.
- * This parameter can be one of the following values:
- * @arg OB_BOR_LEVEL0: Reset level threshold is set to 1.6V
- * @arg OB_BOR_LEVEL1: Reset level threshold is set to 2.1V
- * @arg OB_BOR_LEVEL2: Reset level threshold is set to 2.4V
- * @arg OB_BOR_LEVEL3: Reset level threshold is set to 2.7V
- * @retval None
- */
-static void FLASH_OB_BOR_LevelConfig(uint32_t Level)
-{
- assert_param(IS_OB_BOR_LEVEL(Level));
-
- /* Configure BOR_LEV option byte */
- MODIFY_REG(FLASH->OPTSR_PRG, FLASH_OPTSR_BOR_LEV, Level);
-}
-
-/**
- * @brief Get the BOR Level.
- * @retval The Option Bytes BOR Reset Level.
- * This parameter can be one of the following values:
- * @arg OB_BOR_LEVEL0: Reset level threshold is set to 1.6V
- * @arg OB_BOR_LEVEL1: Reset level threshold is set to 2.1V
- * @arg OB_BOR_LEVEL2: Reset level threshold is set to 2.4V
- * @arg OB_BOR_LEVEL3: Reset level threshold is set to 2.7V
- */
-static uint32_t FLASH_OB_GetBOR(void)
-{
- return (FLASH->OPTSR_CUR & FLASH_OPTSR_BOR_LEV);
-}
-
-/**
- * @brief Set Boot address
- * @param BootOption Boot address option byte to be programmed,
- * This parameter must be a value of @ref FLASHEx_OB_BOOT_OPTION
- (OB_BOOT_ADD0, OB_BOOT_ADD1 or OB_BOOT_ADD_BOTH)
- *
- * @param BootAddress0 Specifies the Boot Address 0
- * @param BootAddress1 Specifies the Boot Address 1
- * @retval HAL Status
- */
-static void FLASH_OB_BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1)
-{
- /* Check the parameters */
- assert_param(IS_OB_BOOT_ADD_OPTION(BootOption));
-
- if((BootOption & OB_BOOT_ADD0) == OB_BOOT_ADD0)
- {
- /* Check the parameters */
- assert_param(IS_BOOT_ADDRESS(BootAddress0));
-
- /* Configure CM7 BOOT ADD0 */
-#if defined(DUAL_CORE)
- MODIFY_REG(FLASH->BOOT7_PRG, FLASH_BOOT7_BCM7_ADD0, (BootAddress0 >> 16));
-#else /* Single Core*/
- MODIFY_REG(FLASH->BOOT_PRG, FLASH_BOOT_ADD0, (BootAddress0 >> 16));
-#endif /* DUAL_CORE */
- }
-
- if((BootOption & OB_BOOT_ADD1) == OB_BOOT_ADD1)
- {
- /* Check the parameters */
- assert_param(IS_BOOT_ADDRESS(BootAddress1));
-
- /* Configure CM7 BOOT ADD1 */
-#if defined(DUAL_CORE)
- MODIFY_REG(FLASH->BOOT7_PRG, FLASH_BOOT7_BCM7_ADD1, BootAddress1);
-#else /* Single Core*/
- MODIFY_REG(FLASH->BOOT_PRG, FLASH_BOOT_ADD1, BootAddress1);
-#endif /* DUAL_CORE */
- }
-}
-
-/**
- * @brief Get Boot address
- * @param BootAddress0 Specifies the Boot Address 0.
- * @param BootAddress1 Specifies the Boot Address 1.
- * @retval HAL Status
- */
-static void FLASH_OB_GetBootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1)
-{
- uint32_t regvalue;
-
-#if defined(DUAL_CORE)
- regvalue = FLASH->BOOT7_CUR;
-
- (*BootAddress0) = (regvalue & FLASH_BOOT7_BCM7_ADD0) << 16;
- (*BootAddress1) = (regvalue & FLASH_BOOT7_BCM7_ADD1);
-#else /* Single Core */
- regvalue = FLASH->BOOT_CUR;
-
- (*BootAddress0) = (regvalue & FLASH_BOOT_ADD0) << 16;
- (*BootAddress1) = (regvalue & FLASH_BOOT_ADD1);
-#endif /* DUAL_CORE */
-}
-
-#if defined(DUAL_CORE)
-/**
- * @brief Set CM4 Boot address
- * @param BootOption Boot address option byte to be programmed,
- * This parameter must be a value of @ref FLASHEx_OB_BOOT_OPTION
- (OB_BOOT_ADD0, OB_BOOT_ADD1 or OB_BOOT_ADD_BOTH)
- *
- * @param BootAddress0 Specifies the CM4 Boot Address 0.
- * @param BootAddress1 Specifies the CM4 Boot Address 1.
- * @retval HAL Status
- */
-static void FLASH_OB_CM4BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1)
-{
- /* Check the parameters */
- assert_param(IS_OB_BOOT_ADD_OPTION(BootOption));
-
- if((BootOption & OB_BOOT_ADD0) == OB_BOOT_ADD0)
- {
- /* Check the parameters */
- assert_param(IS_BOOT_ADDRESS(BootAddress0));
-
- /* Configure CM4 BOOT ADD0 */
- MODIFY_REG(FLASH->BOOT4_PRG, FLASH_BOOT4_BCM4_ADD0, (BootAddress0 >> 16));
-
- }
-
- if((BootOption & OB_BOOT_ADD1) == OB_BOOT_ADD1)
- {
- /* Check the parameters */
- assert_param(IS_BOOT_ADDRESS(BootAddress1));
-
- /* Configure CM4 BOOT ADD1 */
- MODIFY_REG(FLASH->BOOT4_PRG, FLASH_BOOT4_BCM4_ADD1, BootAddress1);
- }
-}
-
-/**
- * @brief Get CM4 Boot address
- * @param BootAddress0 Specifies the CM4 Boot Address 0.
- * @param BootAddress1 Specifies the CM4 Boot Address 1.
- * @retval HAL Status
- */
-static void FLASH_OB_GetCM4BootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1)
-{
- uint32_t regvalue;
-
- regvalue = FLASH->BOOT4_CUR;
-
- (*BootAddress0) = (regvalue & FLASH_BOOT4_BCM4_ADD0) << 16;
- (*BootAddress1) = (regvalue & FLASH_BOOT4_BCM4_ADD1);
-}
-#endif /*DUAL_CORE*/
-
-/**
- * @brief Set secure area configuration
- * @param SecureAreaConfig specify if the secure area will be deleted or not
- * when RDP level decreased from Level 1 to Level 0 or during a mass erase.
- *
- * @param SecureAreaStartAddr Specifies the secure area start address
- * @param SecureAreaEndAddr Specifies the secure area end address
- * @param Banks the specific bank to apply Security protection
- * This parameter can be one of the following values:
- * @arg FLASH_BANK_1: Secure area on specified bank1 area
- * @arg FLASH_BANK_2: Secure area on specified bank2 area
- * @arg FLASH_BANK_BOTH: Secure area on specified bank1 and bank2 area (same config will be applied on both banks)
- * @retval None
- */
-static void FLASH_OB_SecureAreaConfig(uint32_t SecureAreaConfig, uint32_t SecureAreaStartAddr, uint32_t SecureAreaEndAddr, uint32_t Banks)
-{
- /* Check the parameters */
- assert_param(IS_FLASH_BANK(Banks));
- assert_param(IS_OB_SECURE_RDP(SecureAreaConfig));
-
- if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
- {
- /* Check the parameters */
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(SecureAreaStartAddr));
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(SecureAreaEndAddr));
-
- /* Configure the secure area */
- FLASH->SCAR_PRG1 = ((SecureAreaStartAddr - FLASH_BANK1_BASE) >> 8) | \
- (((SecureAreaEndAddr - FLASH_BANK1_BASE) >> 8) << FLASH_SCAR_SEC_AREA_END_Pos) | \
- (SecureAreaConfig & FLASH_SCAR_DMES);
- }
-
- if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
- {
- /* Check the parameters */
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(SecureAreaStartAddr));
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(SecureAreaEndAddr));
-
- /* Configure the secure area */
- FLASH->SCAR_PRG2 = ((SecureAreaStartAddr - FLASH_BANK2_BASE) >> 8) | \
- (((SecureAreaEndAddr - FLASH_BANK2_BASE) >> 8) << FLASH_SCAR_SEC_AREA_END_Pos) | \
- (SecureAreaConfig & FLASH_SCAR_DMES);
- }
-}
-
-/**
- * @brief Get secure area configuration
- * @param SecureAreaConfig indicates if the secure area will be deleted or not
- * when RDP level decreased from Level 1 to Level 0 or during a mass erase.
- * @param SecureAreaStartAddr gives the secure area start address
- * @param SecureAreaEndAddr gives the secure area end address
- * @param Bank Specifies the Bank
- * @retval None
- */
-static void FLASH_OB_GetSecureArea(uint32_t *SecureAreaConfig, uint32_t *SecureAreaStartAddr, uint32_t *SecureAreaEndAddr, uint32_t Bank)
-{
- uint32_t regvalue = 0;
- uint32_t bankBase = 0;
-
- /* Check Bank parameter value */
- if((Bank & FLASH_BANK_BOTH) == FLASH_BANK_1)
- {
- regvalue = FLASH->SCAR_CUR1;
- bankBase = FLASH_BANK1_BASE;
- }
-
- if((Bank & FLASH_BANK_BOTH) == FLASH_BANK_2)
- {
- regvalue = FLASH->SCAR_CUR2;
- bankBase = FLASH_BANK2_BASE;
- }
-
- /* Get the secure area settings */
- (*SecureAreaConfig) = (regvalue & FLASH_SCAR_DMES);
- (*SecureAreaStartAddr) = ((regvalue & FLASH_SCAR_SEC_AREA_START) << 8) + bankBase;
- (*SecureAreaEndAddr) = (regvalue & FLASH_SCAR_SEC_AREA_END) >> FLASH_SCAR_SEC_AREA_END_Pos;
- (*SecureAreaEndAddr) = ((*SecureAreaEndAddr) << 8) + bankBase;
-}
-
-/**
- * @brief Add a CRC sector to the list of sectors on which the CRC will be calculated
- * @param Sector Specifies the CRC sector number
- * @param Bank Specifies the Bank
- * @retval None
- */
-static void FLASH_CRC_AddSector(uint32_t Sector, uint32_t Bank)
-{
- /* Check the parameters */
- assert_param(IS_FLASH_SECTOR(Sector));
-
- if (Bank == FLASH_BANK_1)
- {
- /* Clear CRC sector */
- FLASH->CRCCR1 &= (~FLASH_CRCCR_CRC_SECT);
-
- /* Select CRC Sector and activate ADD_SECT bit */
- FLASH->CRCCR1 |= Sector | FLASH_CRCCR_ADD_SECT;
- }
- else
- {
- /* Clear CRC sector */
- FLASH->CRCCR2 &= (~FLASH_CRCCR_CRC_SECT);
-
- /* Select CRC Sector and activate ADD_SECT bit */
- FLASH->CRCCR2 |= Sector | FLASH_CRCCR_ADD_SECT;
- }
-}
-
-/**
- * @brief Select CRC start and end memory addresses on which the CRC will be calculated
- * @param CRCStartAddr Specifies the CRC start address
- * @param CRCEndAddr Specifies the CRC end address
- * @param Bank Specifies the Bank
- * @retval None
- */
-static void FLASH_CRC_SelectAddress(uint32_t CRCStartAddr, uint32_t CRCEndAddr, uint32_t Bank)
-{
- if (Bank == FLASH_BANK_1)
- {
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(CRCStartAddr));
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(CRCEndAddr));
-
- /* Write CRC Start and End addresses */
- FLASH->CRCSADD1 = CRCStartAddr;
- FLASH->CRCEADD1 = CRCEndAddr;
- }
- else
- {
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(CRCStartAddr));
- assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(CRCEndAddr));
-
- /* Write CRC Start and End addresses */
- FLASH->CRCSADD2 = CRCStartAddr;
- FLASH->CRCEADD2 = CRCEndAddr;
- }
-}
-/**
- * @}
- */
-
-#if defined (FLASH_OTPBL_LOCKBL)
-/**
- * @brief Configure the OTP Block Lock.
- * @param OTP_Block specifies the OTP Block to lock.
- * This parameter can be a value of @ref FLASHEx_OTP_Blocks
- * @retval None
- */
-static void FLASH_OB_OTP_LockConfig(uint32_t OTP_Block)
-{
- /* Check the parameters */
- assert_param(IS_OTP_BLOCK(OTP_Block));
-
- /* Configure the OTP Block lock in the option bytes register */
- FLASH->OTPBL_PRG |= (OTP_Block & FLASH_OTPBL_LOCKBL);
-}
-
-/**
- * @brief Get the OTP Block Lock.
- * @retval OTP_Block specifies the OTP Block to lock.
- * This return value can be a value of @ref FLASHEx_OTP_Blocks
- */
-static uint32_t FLASH_OB_OTP_GetLock(void)
-{
- return (FLASH->OTPBL_CUR);
-}
-#endif /* FLASH_OTPBL_LOCKBL */
-
-#endif /* HAL_FLASH_MODULE_ENABLED */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+ * @brief Extended IO operation functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Extended programming operation functions #####
+ ===============================================================================
+ [..]
+ This subsection provides a set of functions allowing to manage the Extension FLASH
+ programming operations Operations.
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Perform a mass erase or erase the specified FLASH memory sectors
+ * @param[in] pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
+ * contains the configuration information for the erasing.
+ *
+ * @param[out] SectorError pointer to variable that contains the configuration
+ * information on faulty sector in case of error (0xFFFFFFFF means that all
+ * the sectors have been correctly erased)
+ *
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *SectorError)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+ uint32_t sector_index;
+
+ /* Check the parameters */
+ assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
+ assert_param(IS_FLASH_BANK(pEraseInit->Banks));
+
+ /* Process Locked */
+ __HAL_LOCK(&pFlash);
+
+ /* Reset error code */
+ pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+ /* Wait for last operation to be completed on Bank1 */
+ if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+ }
+
+#if defined (DUAL_BANK)
+ /* Wait for last operation to be completed on Bank2 */
+ if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+ }
+#endif /* DUAL_BANK */
+
+ if(status == HAL_OK)
+ {
+ if(pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
+ {
+ /* Mass erase to be done */
+ FLASH_MassErase(pEraseInit->VoltageRange, pEraseInit->Banks);
+
+ /* Wait for last operation to be completed on Bank 1 */
+ if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+ /* if the erase operation is completed, disable the Bank1 BER Bit */
+ FLASH->CR1 &= (~FLASH_CR_BER);
+ }
+#if defined (DUAL_BANK)
+ /* Wait for last operation to be completed on Bank 2 */
+ if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+ /* if the erase operation is completed, disable the Bank2 BER Bit */
+ FLASH->CR2 &= (~FLASH_CR_BER);
+ }
+#endif /* DUAL_BANK */
+ }
+ else
+ {
+ /*Initialization of SectorError variable*/
+ *SectorError = 0xFFFFFFFFU;
+
+ /* Erase by sector by sector to be done*/
+ for(sector_index = pEraseInit->Sector; sector_index < (pEraseInit->NbSectors + pEraseInit->Sector); sector_index++)
+ {
+ FLASH_Erase_Sector(sector_index, pEraseInit->Banks, pEraseInit->VoltageRange);
+
+ if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1);
+
+ /* If the erase operation is completed, disable the SER Bit */
+ FLASH->CR1 &= (~(FLASH_CR_SER | FLASH_CR_SNB));
+ }
+#if defined (DUAL_BANK)
+ if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ /* Wait for last operation to be completed */
+ status = FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2);
+
+ /* If the erase operation is completed, disable the SER Bit */
+ FLASH->CR2 &= (~(FLASH_CR_SER | FLASH_CR_SNB));
+ }
+#endif /* DUAL_BANK */
+
+ if(status != HAL_OK)
+ {
+ /* In case of error, stop erase procedure and return the faulty sector */
+ *SectorError = sector_index;
+ break;
+ }
+ }
+ }
+ }
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(&pFlash);
+
+ return status;
+}
+
+/**
+ * @brief Perform a mass erase or erase the specified FLASH memory sectors with interrupt enabled
+ * @param pEraseInit pointer to an FLASH_EraseInitTypeDef structure that
+ * contains the configuration information for the erasing.
+ *
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_FLASH_TYPEERASE(pEraseInit->TypeErase));
+ assert_param(IS_FLASH_BANK(pEraseInit->Banks));
+
+ /* Process Locked */
+ __HAL_LOCK(&pFlash);
+
+ /* Reset error code */
+ pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+ /* Wait for last operation to be completed on Bank 1 */
+ if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+ }
+
+#if defined (DUAL_BANK)
+ /* Wait for last operation to be completed on Bank 2 */
+ if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+ }
+#endif /* DUAL_BANK */
+
+ if (status != HAL_OK)
+ {
+ /* Process Unlocked */
+ __HAL_UNLOCK(&pFlash);
+ }
+ else
+ {
+ if((pEraseInit->Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ /* Enable End of Operation and Error interrupts for Bank 1 */
+#if defined (FLASH_CR_OPERRIE)
+ __HAL_FLASH_ENABLE_IT_BANK1(FLASH_IT_EOP_BANK1 | FLASH_IT_WRPERR_BANK1 | FLASH_IT_PGSERR_BANK1 | \
+ FLASH_IT_STRBERR_BANK1 | FLASH_IT_INCERR_BANK1 | FLASH_IT_OPERR_BANK1);
+#else
+ __HAL_FLASH_ENABLE_IT_BANK1(FLASH_IT_EOP_BANK1 | FLASH_IT_WRPERR_BANK1 | FLASH_IT_PGSERR_BANK1 | \
+ FLASH_IT_STRBERR_BANK1 | FLASH_IT_INCERR_BANK1);
+#endif /* FLASH_CR_OPERRIE */
+ }
+#if defined (DUAL_BANK)
+ if((pEraseInit->Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ /* Enable End of Operation and Error interrupts for Bank 2 */
+#if defined (FLASH_CR_OPERRIE)
+ __HAL_FLASH_ENABLE_IT_BANK2(FLASH_IT_EOP_BANK2 | FLASH_IT_WRPERR_BANK2 | FLASH_IT_PGSERR_BANK2 | \
+ FLASH_IT_STRBERR_BANK2 | FLASH_IT_INCERR_BANK2 | FLASH_IT_OPERR_BANK2);
+#else
+ __HAL_FLASH_ENABLE_IT_BANK2(FLASH_IT_EOP_BANK2 | FLASH_IT_WRPERR_BANK2 | FLASH_IT_PGSERR_BANK2 | \
+ FLASH_IT_STRBERR_BANK2 | FLASH_IT_INCERR_BANK2);
+#endif /* FLASH_CR_OPERRIE */
+ }
+#endif /* DUAL_BANK */
+
+ if(pEraseInit->TypeErase == FLASH_TYPEERASE_MASSERASE)
+ {
+ /*Mass erase to be done*/
+ if(pEraseInit->Banks == FLASH_BANK_1)
+ {
+ pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE_BANK1;
+ }
+#if defined (DUAL_BANK)
+ else if(pEraseInit->Banks == FLASH_BANK_2)
+ {
+ pFlash.ProcedureOnGoing = FLASH_PROC_MASSERASE_BANK2;
+ }
+#endif /* DUAL_BANK */
+ else
+ {
+ pFlash.ProcedureOnGoing = FLASH_PROC_ALLBANK_MASSERASE;
+ }
+
+ FLASH_MassErase(pEraseInit->VoltageRange, pEraseInit->Banks);
+ }
+ else
+ {
+ /* Erase by sector to be done */
+#if defined (DUAL_BANK)
+ if(pEraseInit->Banks == FLASH_BANK_1)
+ {
+ pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE_BANK1;
+ }
+ else
+ {
+ pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE_BANK2;
+ }
+#else
+ pFlash.ProcedureOnGoing = FLASH_PROC_SECTERASE_BANK1;
+#endif /* DUAL_BANK */
+
+ pFlash.NbSectorsToErase = pEraseInit->NbSectors;
+ pFlash.Sector = pEraseInit->Sector;
+ pFlash.VoltageForErase = pEraseInit->VoltageRange;
+
+ /* Erase first sector and wait for IT */
+ FLASH_Erase_Sector(pEraseInit->Sector, pEraseInit->Banks, pEraseInit->VoltageRange);
+ }
+ }
+
+ return status;
+}
+
+/**
+ * @brief Program option bytes
+ * @param pOBInit pointer to an FLASH_OBProgramInitTypeDef structure that
+ * contains the configuration information for the programming.
+ *
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit)
+{
+ HAL_StatusTypeDef status;
+
+ /* Check the parameters */
+ assert_param(IS_OPTIONBYTE(pOBInit->OptionType));
+
+ /* Process Locked */
+ __HAL_LOCK(&pFlash);
+
+ /* Reset Error Code */
+ pFlash.ErrorCode = HAL_FLASH_ERROR_NONE;
+
+ /* Wait for last operation to be completed */
+ if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+#if defined (DUAL_BANK)
+ else if(FLASH_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2) != HAL_OK)
+ {
+ status = HAL_ERROR;
+ }
+#endif /* DUAL_BANK */
+ else
+ {
+ status = HAL_OK;
+ }
+
+ if(status == HAL_OK)
+ {
+ /*Write protection configuration*/
+ if((pOBInit->OptionType & OPTIONBYTE_WRP) == OPTIONBYTE_WRP)
+ {
+ assert_param(IS_WRPSTATE(pOBInit->WRPState));
+
+ if(pOBInit->WRPState == OB_WRPSTATE_ENABLE)
+ {
+ /*Enable of Write protection on the selected Sector*/
+ FLASH_OB_EnableWRP(pOBInit->WRPSector,pOBInit->Banks);
+ }
+ else
+ {
+ /*Disable of Write protection on the selected Sector*/
+ FLASH_OB_DisableWRP(pOBInit->WRPSector, pOBInit->Banks);
+ }
+ }
+
+ /* Read protection configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_RDP) != 0U)
+ {
+ /* Configure the Read protection level */
+ FLASH_OB_RDPConfig(pOBInit->RDPLevel);
+ }
+
+ /* User Configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_USER) != 0U)
+ {
+ /* Configure the user option bytes */
+ FLASH_OB_UserConfig(pOBInit->USERType, pOBInit->USERConfig);
+ }
+
+ /* PCROP Configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_PCROP) != 0U)
+ {
+ assert_param(IS_FLASH_BANK(pOBInit->Banks));
+
+ /*Configure the Proprietary code readout protection */
+ FLASH_OB_PCROPConfig(pOBInit->PCROPConfig, pOBInit->PCROPStartAddr, pOBInit->PCROPEndAddr, pOBInit->Banks);
+ }
+
+ /* BOR Level configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_BOR) == OPTIONBYTE_BOR)
+ {
+ FLASH_OB_BOR_LevelConfig(pOBInit->BORLevel);
+ }
+
+#if defined(DUAL_CORE)
+ /* CM7 Boot Address configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_CM7_BOOTADD) == OPTIONBYTE_CM7_BOOTADD)
+ {
+ FLASH_OB_BootAddConfig(pOBInit->BootConfig, pOBInit->BootAddr0, pOBInit->BootAddr1);
+ }
+
+ /* CM4 Boot Address configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_CM4_BOOTADD) == OPTIONBYTE_CM4_BOOTADD)
+ {
+ FLASH_OB_CM4BootAddConfig(pOBInit->CM4BootConfig, pOBInit->CM4BootAddr0, pOBInit->CM4BootAddr1);
+ }
+#else /* Single Core*/
+ /* Boot Address configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_BOOTADD) == OPTIONBYTE_BOOTADD)
+ {
+ FLASH_OB_BootAddConfig(pOBInit->BootConfig, pOBInit->BootAddr0, pOBInit->BootAddr1);
+ }
+#endif /*DUAL_CORE*/
+
+ /* Secure area configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_SECURE_AREA) == OPTIONBYTE_SECURE_AREA)
+ {
+ FLASH_OB_SecureAreaConfig(pOBInit->SecureAreaConfig, pOBInit->SecureAreaStartAddr, pOBInit->SecureAreaEndAddr,pOBInit->Banks);
+ }
+
+#if defined(FLASH_OTPBL_LOCKBL)
+ /* OTP Block Lock configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_OTP_LOCK) == OPTIONBYTE_OTP_LOCK)
+ {
+ FLASH_OB_OTP_LockConfig(pOBInit->OTPBlockLock);
+ }
+#endif /* FLASH_OTPBL_LOCKBL */
+
+#if defined(FLASH_OPTSR2_TCM_AXI_SHARED)
+ /* TCM / AXI Shared RAM configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_SHARED_RAM) == OPTIONBYTE_SHARED_RAM)
+ {
+ FLASH_OB_SharedRAM_Config(pOBInit->SharedRamConfig);
+ }
+#endif /* FLASH_OPTSR2_TCM_AXI_SHARED */
+
+#if defined(FLASH_OPTSR2_CPUFREQ_BOOST)
+ /* CPU Frequency Boost configuration */
+ if((pOBInit->OptionType & OPTIONBYTE_FREQ_BOOST) == OPTIONBYTE_FREQ_BOOST)
+ {
+ FLASH_OB_CPUFreq_BoostConfig(pOBInit->FreqBoostState);
+ }
+#endif /* FLASH_OPTSR2_CPUFREQ_BOOST */
+ }
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(&pFlash);
+
+ return status;
+}
+
+/**
+ * @brief Get the Option byte configuration
+ * @param pOBInit pointer to an FLASH_OBProgramInitTypeDef structure that
+ * contains the configuration information for the programming.
+ * @note The parameter Banks of the pOBInit structure must be set exclusively to FLASH_BANK_1 or FLASH_BANK_2,
+ * as this parameter is use to get the given Bank WRP, PCROP and secured area configuration.
+ *
+ * @retval None
+ */
+void HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit)
+{
+ pOBInit->OptionType = (OPTIONBYTE_USER | OPTIONBYTE_RDP | OPTIONBYTE_BOR);
+
+ /* Get Read protection level */
+ pOBInit->RDPLevel = FLASH_OB_GetRDP();
+
+ /* Get the user option bytes */
+ pOBInit->USERConfig = FLASH_OB_GetUser();
+
+ /*Get BOR Level*/
+ pOBInit->BORLevel = FLASH_OB_GetBOR();
+
+#if defined (DUAL_BANK)
+ if ((pOBInit->Banks == FLASH_BANK_1) || (pOBInit->Banks == FLASH_BANK_2))
+#else
+ if (pOBInit->Banks == FLASH_BANK_1)
+#endif /* DUAL_BANK */
+ {
+ pOBInit->OptionType |= (OPTIONBYTE_WRP | OPTIONBYTE_PCROP | OPTIONBYTE_SECURE_AREA);
+
+ /* Get write protection on the selected area */
+ FLASH_OB_GetWRP(&(pOBInit->WRPState), &(pOBInit->WRPSector), pOBInit->Banks);
+
+ /* Get the Proprietary code readout protection */
+ FLASH_OB_GetPCROP(&(pOBInit->PCROPConfig), &(pOBInit->PCROPStartAddr), &(pOBInit->PCROPEndAddr), pOBInit->Banks);
+
+ /*Get Bank Secure area*/
+ FLASH_OB_GetSecureArea(&(pOBInit->SecureAreaConfig), &(pOBInit->SecureAreaStartAddr), &(pOBInit->SecureAreaEndAddr), pOBInit->Banks);
+ }
+
+ /*Get Boot Address*/
+ FLASH_OB_GetBootAdd(&(pOBInit->BootAddr0), &(pOBInit->BootAddr1));
+#if defined(DUAL_CORE)
+ pOBInit->OptionType |= OPTIONBYTE_CM7_BOOTADD | OPTIONBYTE_CM4_BOOTADD;
+
+ /*Get CM4 Boot Address*/
+ FLASH_OB_GetCM4BootAdd(&(pOBInit->CM4BootAddr0), &(pOBInit->CM4BootAddr1));
+#else
+ pOBInit->OptionType |= OPTIONBYTE_BOOTADD;
+#endif /*DUAL_CORE*/
+
+#if defined (FLASH_OTPBL_LOCKBL)
+ pOBInit->OptionType |= OPTIONBYTE_OTP_LOCK;
+
+ /* Get OTP Block Lock */
+ pOBInit->OTPBlockLock = FLASH_OB_OTP_GetLock();
+#endif /* FLASH_OTPBL_LOCKBL */
+
+#if defined (FLASH_OPTSR2_TCM_AXI_SHARED)
+ pOBInit->OptionType |= OPTIONBYTE_SHARED_RAM;
+
+ /* Get TCM / AXI Shared RAM */
+ pOBInit->SharedRamConfig = FLASH_OB_SharedRAM_GetConfig();
+#endif /* FLASH_OPTSR2_TCM_AXI_SHARED */
+
+#if defined (FLASH_OPTSR2_CPUFREQ_BOOST)
+ pOBInit->OptionType |= OPTIONBYTE_FREQ_BOOST;
+
+ /* Get CPU Frequency Boost */
+ pOBInit->FreqBoostState = FLASH_OB_CPUFreq_GetBoost();
+#endif /* FLASH_OPTSR2_CPUFREQ_BOOST */
+}
+
+/**
+ * @brief Unlock the FLASH Bank1 control registers access
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_Unlock_Bank1(void)
+{
+ if(READ_BIT(FLASH->CR1, FLASH_CR_LOCK) != 0U)
+ {
+ /* Authorize the FLASH Bank1 Registers access */
+ WRITE_REG(FLASH->KEYR1, FLASH_KEY1);
+ WRITE_REG(FLASH->KEYR1, FLASH_KEY2);
+
+ /* Verify Flash Bank1 is unlocked */
+ if (READ_BIT(FLASH->CR1, FLASH_CR_LOCK) != 0U)
+ {
+ return HAL_ERROR;
+ }
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Locks the FLASH Bank1 control registers access
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_Lock_Bank1(void)
+{
+ /* Set the LOCK Bit to lock the FLASH Bank1 Registers access */
+ SET_BIT(FLASH->CR1, FLASH_CR_LOCK);
+ return HAL_OK;
+}
+
+#if defined (DUAL_BANK)
+/**
+ * @brief Unlock the FLASH Bank2 control registers access
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_Unlock_Bank2(void)
+{
+ if(READ_BIT(FLASH->CR2, FLASH_CR_LOCK) != 0U)
+ {
+ /* Authorize the FLASH Bank2 Registers access */
+ WRITE_REG(FLASH->KEYR2, FLASH_KEY1);
+ WRITE_REG(FLASH->KEYR2, FLASH_KEY2);
+
+ /* Verify Flash Bank1 is unlocked */
+ if (READ_BIT(FLASH->CR2, FLASH_CR_LOCK) != 0U)
+ {
+ return HAL_ERROR;
+ }
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Locks the FLASH Bank2 control registers access
+ * @retval HAL Status
+ */
+HAL_StatusTypeDef HAL_FLASHEx_Lock_Bank2(void)
+{
+ /* Set the LOCK Bit to lock the FLASH Bank2 Registers access */
+ SET_BIT(FLASH->CR2, FLASH_CR_LOCK);
+ return HAL_OK;
+}
+#endif /* DUAL_BANK */
+
+/*
+ * @brief Perform a CRC computation on the specified FLASH memory area
+ * @param pCRCInit pointer to an FLASH_CRCInitTypeDef structure that
+ * contains the configuration information for the CRC computation.
+ * @note CRC computation uses CRC-32 (Ethernet) polynomial 0x4C11DB7
+ * @note The application should avoid running a CRC on PCROP or secure-only
+ * user Flash memory area since it may alter the expected CRC value.
+ * A special error flag (CRC read error: CRCRDERR) can be used to
+ * detect such a case.
+ * @retval HAL Status
+*/
+HAL_StatusTypeDef HAL_FLASHEx_ComputeCRC(FLASH_CRCInitTypeDef *pCRCInit, uint32_t *CRC_Result)
+{
+ HAL_StatusTypeDef status;
+ uint32_t sector_index;
+
+ /* Check the parameters */
+ assert_param(IS_FLASH_BANK_EXCLUSIVE(pCRCInit->Bank));
+ assert_param(IS_FLASH_TYPECRC(pCRCInit->TypeCRC));
+
+ /* Wait for OB change operation to be completed */
+ status = FLASH_OB_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE);
+
+ if (status == HAL_OK)
+ {
+ if (pCRCInit->Bank == FLASH_BANK_1)
+ {
+ /* Enable CRC feature */
+ FLASH->CR1 |= FLASH_CR_CRC_EN;
+
+ /* Clear CRC flags in Status Register: CRC end of calculation and CRC read error */
+ FLASH->CCR1 |= (FLASH_CCR_CLR_CRCEND | FLASH_CCR_CLR_CRCRDERR);
+
+ /* Clear current CRC result, program burst size and define memory area on which CRC has to be computed */
+ FLASH->CRCCR1 |= FLASH_CRCCR_CLEAN_CRC | pCRCInit->BurstSize | pCRCInit->TypeCRC;
+
+ if (pCRCInit->TypeCRC == FLASH_CRC_SECTORS)
+ {
+ /* Clear sectors list */
+ FLASH->CRCCR1 |= FLASH_CRCCR_CLEAN_SECT;
+
+ /* Select CRC sectors */
+ for(sector_index = pCRCInit->Sector; sector_index < (pCRCInit->NbSectors + pCRCInit->Sector); sector_index++)
+ {
+ FLASH_CRC_AddSector(sector_index, FLASH_BANK_1);
+ }
+ }
+ else if (pCRCInit->TypeCRC == FLASH_CRC_BANK)
+ {
+ /* Enable Bank 1 CRC select bit */
+ FLASH->CRCCR1 |= FLASH_CRCCR_ALL_BANK;
+ }
+ else
+ {
+ /* Select CRC start and end addresses */
+ FLASH_CRC_SelectAddress(pCRCInit->CRCStartAddr, pCRCInit->CRCEndAddr, FLASH_BANK_1);
+ }
+
+ /* Start the CRC calculation */
+ FLASH->CRCCR1 |= FLASH_CRCCR_START_CRC;
+
+ /* Wait on CRC busy flag */
+ status = FLASH_CRC_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_1);
+
+ /* Return CRC result */
+ (*CRC_Result) = FLASH->CRCDATA;
+
+ /* Disable CRC feature */
+ FLASH->CR1 &= (~FLASH_CR_CRC_EN);
+
+ /* Clear CRC flags */
+ __HAL_FLASH_CLEAR_FLAG_BANK1(FLASH_FLAG_CRCEND_BANK1 | FLASH_FLAG_CRCRDERR_BANK1);
+ }
+#if defined (DUAL_BANK)
+ else
+ {
+ /* Enable CRC feature */
+ FLASH->CR2 |= FLASH_CR_CRC_EN;
+
+ /* Clear CRC flags in Status Register: CRC end of calculation and CRC read error */
+ FLASH->CCR2 |= (FLASH_CCR_CLR_CRCEND | FLASH_CCR_CLR_CRCRDERR);
+
+ /* Clear current CRC result, program burst size and define memory area on which CRC has to be computed */
+ FLASH->CRCCR2 |= FLASH_CRCCR_CLEAN_CRC | pCRCInit->BurstSize | pCRCInit->TypeCRC;
+
+ if (pCRCInit->TypeCRC == FLASH_CRC_SECTORS)
+ {
+ /* Clear sectors list */
+ FLASH->CRCCR2 |= FLASH_CRCCR_CLEAN_SECT;
+
+ /* Add CRC sectors */
+ for(sector_index = pCRCInit->Sector; sector_index < (pCRCInit->NbSectors + pCRCInit->Sector); sector_index++)
+ {
+ FLASH_CRC_AddSector(sector_index, FLASH_BANK_2);
+ }
+ }
+ else if (pCRCInit->TypeCRC == FLASH_CRC_BANK)
+ {
+ /* Enable Bank 2 CRC select bit */
+ FLASH->CRCCR2 |= FLASH_CRCCR_ALL_BANK;
+ }
+ else
+ {
+ /* Select CRC start and end addresses */
+ FLASH_CRC_SelectAddress(pCRCInit->CRCStartAddr, pCRCInit->CRCEndAddr, FLASH_BANK_2);
+ }
+
+ /* Start the CRC calculation */
+ FLASH->CRCCR2 |= FLASH_CRCCR_START_CRC;
+
+ /* Wait on CRC busy flag */
+ status = FLASH_CRC_WaitForLastOperation((uint32_t)FLASH_TIMEOUT_VALUE, FLASH_BANK_2);
+
+ /* Return CRC result */
+ (*CRC_Result) = FLASH->CRCDATA;
+
+ /* Disable CRC feature */
+ FLASH->CR2 &= (~FLASH_CR_CRC_EN);
+
+ /* Clear CRC flags */
+ __HAL_FLASH_CLEAR_FLAG_BANK2(FLASH_FLAG_CRCEND_BANK2 | FLASH_FLAG_CRCRDERR_BANK2);
+ }
+#endif /* DUAL_BANK */
+ }
+
+ return status;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Private functions ---------------------------------------------------------*/
+
+/** @addtogroup FLASHEx_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Mass erase of FLASH memory
+ * @param VoltageRange The device program/erase parallelism.
+ * This parameter can be one of the following values:
+ * @arg FLASH_VOLTAGE_RANGE_1 : Flash program/erase by 8 bits
+ * @arg FLASH_VOLTAGE_RANGE_2 : Flash program/erase by 16 bits
+ * @arg FLASH_VOLTAGE_RANGE_3 : Flash program/erase by 32 bits
+ * @arg FLASH_VOLTAGE_RANGE_4 : Flash program/erase by 64 bits
+ *
+ * @param Banks Banks to be erased
+ * This parameter can be one of the following values:
+ * @arg FLASH_BANK_1: Bank1 to be erased
+ * @arg FLASH_BANK_2: Bank2 to be erased
+ * @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased
+ *
+ * @retval HAL Status
+ */
+static void FLASH_MassErase(uint32_t VoltageRange, uint32_t Banks)
+{
+ /* Check the parameters */
+#if defined (FLASH_CR_PSIZE)
+ assert_param(IS_VOLTAGERANGE(VoltageRange));
+#else
+ UNUSED(VoltageRange);
+#endif /* FLASH_CR_PSIZE */
+ assert_param(IS_FLASH_BANK(Banks));
+
+#if defined (DUAL_BANK)
+ /* Flash Mass Erase */
+ if((Banks & FLASH_BANK_BOTH) == FLASH_BANK_BOTH)
+ {
+#if defined (FLASH_CR_PSIZE)
+ /* Reset Program/erase VoltageRange for Bank1 and Bank2 */
+ FLASH->CR1 &= (~FLASH_CR_PSIZE);
+ FLASH->CR2 &= (~FLASH_CR_PSIZE);
+
+ /* Set voltage range */
+ FLASH->CR1 |= VoltageRange;
+ FLASH->CR2 |= VoltageRange;
+#endif /* FLASH_CR_PSIZE */
+
+ /* Set Mass Erase Bit */
+ FLASH->OPTCR |= FLASH_OPTCR_MER;
+ }
+ else
+#endif /* DUAL_BANK */
+ {
+ /* Proceed to erase Flash Bank */
+ if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+#if defined (FLASH_CR_PSIZE)
+ /* Set Program/erase VoltageRange for Bank1 */
+ FLASH->CR1 &= (~FLASH_CR_PSIZE);
+ FLASH->CR1 |= VoltageRange;
+#endif /* FLASH_CR_PSIZE */
+
+ /* Erase Bank1 */
+ FLASH->CR1 |= (FLASH_CR_BER | FLASH_CR_START);
+ }
+
+#if defined (DUAL_BANK)
+ if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+#if defined (FLASH_CR_PSIZE)
+ /* Set Program/erase VoltageRange for Bank2 */
+ FLASH->CR2 &= (~FLASH_CR_PSIZE);
+ FLASH->CR2 |= VoltageRange;
+#endif /* FLASH_CR_PSIZE */
+
+ /* Erase Bank2 */
+ FLASH->CR2 |= (FLASH_CR_BER | FLASH_CR_START);
+ }
+#endif /* DUAL_BANK */
+ }
+}
+
+/**
+ * @brief Erase the specified FLASH memory sector
+ * @param Sector FLASH sector to erase
+ * This parameter can be a value of @ref FLASH_Sectors
+ * @param Banks Banks to be erased
+ * This parameter can be one of the following values:
+ * @arg FLASH_BANK_1: Bank1 to be erased
+ * @arg FLASH_BANK_2: Bank2 to be erased
+ * @arg FLASH_BANK_BOTH: Bank1 and Bank2 to be erased
+ * @param VoltageRange The device program/erase parallelism.
+ * This parameter can be one of the following values:
+ * @arg FLASH_VOLTAGE_RANGE_1 : Flash program/erase by 8 bits
+ * @arg FLASH_VOLTAGE_RANGE_2 : Flash program/erase by 16 bits
+ * @arg FLASH_VOLTAGE_RANGE_3 : Flash program/erase by 32 bits
+ * @arg FLASH_VOLTAGE_RANGE_4 : Flash program/erase by 64 bits
+ *
+ * @retval None
+ */
+void FLASH_Erase_Sector(uint32_t Sector, uint32_t Banks, uint32_t VoltageRange)
+{
+ assert_param(IS_FLASH_SECTOR(Sector));
+ assert_param(IS_FLASH_BANK_EXCLUSIVE(Banks));
+#if defined (FLASH_CR_PSIZE)
+ assert_param(IS_VOLTAGERANGE(VoltageRange));
+#else
+ UNUSED(VoltageRange);
+#endif /* FLASH_CR_PSIZE */
+
+ if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+#if defined (FLASH_CR_PSIZE)
+ /* Reset Program/erase VoltageRange and Sector Number for Bank1 */
+ FLASH->CR1 &= ~(FLASH_CR_PSIZE | FLASH_CR_SNB);
+
+ FLASH->CR1 |= (FLASH_CR_SER | VoltageRange | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
+#else
+ /* Reset Sector Number for Bank1 */
+ FLASH->CR1 &= ~(FLASH_CR_SNB);
+
+ FLASH->CR1 |= (FLASH_CR_SER | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
+#endif /* FLASH_CR_PSIZE */
+ }
+
+#if defined (DUAL_BANK)
+ if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+#if defined (FLASH_CR_PSIZE)
+ /* Reset Program/erase VoltageRange and Sector Number for Bank2 */
+ FLASH->CR2 &= ~(FLASH_CR_PSIZE | FLASH_CR_SNB);
+
+ FLASH->CR2 |= (FLASH_CR_SER | VoltageRange | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
+#else
+ /* Reset Sector Number for Bank2 */
+ FLASH->CR2 &= ~(FLASH_CR_SNB);
+
+ FLASH->CR2 |= (FLASH_CR_SER | (Sector << FLASH_CR_SNB_Pos) | FLASH_CR_START);
+#endif /* FLASH_CR_PSIZE */
+ }
+#endif /* DUAL_BANK */
+}
+
+/**
+ * @brief Enable the write protection of the desired bank1 or bank 2 sectors
+ * @param WRPSector specifies the sector(s) to be write protected.
+ * This parameter can be one of the following values:
+ * @arg WRPSector: A combination of OB_WRP_SECTOR_0 to OB_WRP_SECTOR_7 or OB_WRP_SECTOR_ALL
+ *
+ * @param Banks the specific bank to apply WRP sectors
+ * This parameter can be one of the following values:
+ * @arg FLASH_BANK_1: enable WRP on specified bank1 sectors
+ * @arg FLASH_BANK_2: enable WRP on specified bank2 sectors
+ * @arg FLASH_BANK_BOTH: enable WRP on both bank1 and bank2 specified sectors
+ *
+ * @retval HAL FLASH State
+ */
+static void FLASH_OB_EnableWRP(uint32_t WRPSector, uint32_t Banks)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_WRP_SECTOR(WRPSector));
+ assert_param(IS_FLASH_BANK(Banks));
+
+ if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ /* Enable Write Protection for bank 1 */
+ FLASH->WPSN_PRG1 &= (~(WRPSector & FLASH_WPSN_WRPSN));
+ }
+
+#if defined (DUAL_BANK)
+ if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ /* Enable Write Protection for bank 2 */
+ FLASH->WPSN_PRG2 &= (~(WRPSector & FLASH_WPSN_WRPSN));
+ }
+#endif /* DUAL_BANK */
+}
+
+/**
+ * @brief Disable the write protection of the desired bank1 or bank 2 sectors
+ * @param WRPSector specifies the sector(s) to disable write protection.
+ * This parameter can be one of the following values:
+ * @arg WRPSector: A combination of FLASH_OB_WRP_SECTOR_0 to FLASH_OB_WRP_SECTOR_7 or FLASH_OB_WRP_SECTOR_ALL
+ *
+ * @param Banks the specific bank to apply WRP sectors
+ * This parameter can be one of the following values:
+ * @arg FLASH_BANK_1: disable WRP on specified bank1 sectors
+ * @arg FLASH_BANK_2: disable WRP on specified bank2 sectors
+ * @arg FLASH_BANK_BOTH: disable WRP on both bank1 and bank2 specified sectors
+ *
+ * @retval HAL FLASH State
+ */
+static void FLASH_OB_DisableWRP(uint32_t WRPSector, uint32_t Banks)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_WRP_SECTOR(WRPSector));
+ assert_param(IS_FLASH_BANK(Banks));
+
+ if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ /* Disable Write Protection for bank 1 */
+ FLASH->WPSN_PRG1 |= (WRPSector & FLASH_WPSN_WRPSN);
+ }
+
+#if defined (DUAL_BANK)
+ if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ /* Disable Write Protection for bank 2 */
+ FLASH->WPSN_PRG2 |= (WRPSector & FLASH_WPSN_WRPSN);
+ }
+#endif /* DUAL_BANK */
+}
+
+/**
+ * @brief Get the write protection of the given bank 1 or bank 2 sectors
+ * @param WRPState gives the write protection state on the given bank.
+ * This parameter can be one of the following values:
+ * @arg WRPState: OB_WRPSTATE_DISABLE or OB_WRPSTATE_ENABLE
+
+ * @param WRPSector gives the write protected sector(s) on the given bank .
+ * This parameter can be one of the following values:
+ * @arg WRPSector: A combination of FLASH_OB_WRP_SECTOR_0 to FLASH_OB_WRP_SECTOR_7 or FLASH_OB_WRP_SECTOR_ALL
+ *
+ * @param Bank the specific bank to apply WRP sectors
+ * This parameter can be exclusively one of the following values:
+ * @arg FLASH_BANK_1: Get bank1 WRP sectors
+ * @arg FLASH_BANK_2: Get bank2 WRP sectors
+ * @arg FLASH_BANK_BOTH: note allowed in this functions
+ *
+ * @retval HAL FLASH State
+ */
+static void FLASH_OB_GetWRP(uint32_t *WRPState, uint32_t *WRPSector, uint32_t Bank)
+{
+ uint32_t regvalue = 0U;
+
+ if(Bank == FLASH_BANK_1)
+ {
+ regvalue = FLASH->WPSN_CUR1;
+ }
+
+#if defined (DUAL_BANK)
+ if(Bank == FLASH_BANK_2)
+ {
+ regvalue = FLASH->WPSN_CUR2;
+ }
+#endif /* DUAL_BANK */
+
+ (*WRPSector) = (~regvalue) & FLASH_WPSN_WRPSN;
+
+ if(*WRPSector == 0U)
+ {
+ (*WRPState) = OB_WRPSTATE_DISABLE;
+ }
+ else
+ {
+ (*WRPState) = OB_WRPSTATE_ENABLE;
+ }
+}
+
+/**
+ * @brief Set the read protection level.
+ *
+ * @note To configure the RDP level, the option lock bit OPTLOCK must be
+ * cleared with the call of the HAL_FLASH_OB_Unlock() function.
+ * @note To validate the RDP level, the option bytes must be reloaded
+ * through the call of the HAL_FLASH_OB_Launch() function.
+ * @note !!! Warning : When enabling OB_RDP level 2 it's no more possible
+ * to go back to level 1 or 0 !!!
+ *
+ * @param RDPLevel specifies the read protection level.
+ * This parameter can be one of the following values:
+ * @arg OB_RDP_LEVEL_0: No protection
+ * @arg OB_RDP_LEVEL_1: Read protection of the memory
+ * @arg OB_RDP_LEVEL_2: Full chip protection
+ *
+ * @retval HAL status
+ */
+static void FLASH_OB_RDPConfig(uint32_t RDPLevel)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_RDP_LEVEL(RDPLevel));
+
+ /* Configure the RDP level in the option bytes register */
+ MODIFY_REG(FLASH->OPTSR_PRG, FLASH_OPTSR_RDP, RDPLevel);
+}
+
+/**
+ * @brief Get the read protection level.
+ * @retval RDPLevel specifies the read protection level.
+ * This return value can be one of the following values:
+ * @arg OB_RDP_LEVEL_0: No protection
+ * @arg OB_RDP_LEVEL_1: Read protection of the memory
+ * @arg OB_RDP_LEVEL_2: Full chip protection
+ */
+static uint32_t FLASH_OB_GetRDP(void)
+{
+ uint32_t rdp_level = READ_BIT(FLASH->OPTSR_CUR, FLASH_OPTSR_RDP);
+
+ if ((rdp_level != OB_RDP_LEVEL_0) && (rdp_level != OB_RDP_LEVEL_2))
+ {
+ return (OB_RDP_LEVEL_1);
+ }
+ else
+ {
+ return rdp_level;
+ }
+}
+
+#if defined(DUAL_CORE)
+/**
+ * @brief Program the FLASH User Option Byte.
+ *
+ * @note To configure the user option bytes, the option lock bit OPTLOCK must
+ * be cleared with the call of the HAL_FLASH_OB_Unlock() function.
+ *
+ * @note To validate the user option bytes, the option bytes must be reloaded
+ * through the call of the HAL_FLASH_OB_Launch() function.
+ *
+ * @param UserType The FLASH User Option Bytes to be modified :
+ * a combination of @ref FLASHEx_OB_USER_Type
+ *
+ * @param UserConfig The FLASH User Option Bytes values:
+ * IWDG1_SW(Bit4), IWDG2_SW(Bit 5), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
+ * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
+ * SECURITY(Bit 21), BCM4(Bit 22), BCM7(Bit 23), nRST_STOP_D2(Bit 24),
+ * nRST_STDY_D2(Bit 25), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
+ *
+ * @retval HAL status
+ */
+#else
+/**
+ * @brief Program the FLASH User Option Byte.
+ *
+ * @note To configure the user option bytes, the option lock bit OPTLOCK must
+ * be cleared with the call of the HAL_FLASH_OB_Unlock() function.
+ *
+ * @note To validate the user option bytes, the option bytes must be reloaded
+ * through the call of the HAL_FLASH_OB_Launch() function.
+ *
+ * @param UserType The FLASH User Option Bytes to be modified :
+ * a combination of @arg FLASHEx_OB_USER_Type
+ *
+ * @param UserConfig The FLASH User Option Bytes values:
+ * IWDG_SW(Bit4), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
+ * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
+ * SECURITY(Bit 21), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
+ *
+ * @retval HAL status
+ */
+#endif /*DUAL_CORE*/
+static void FLASH_OB_UserConfig(uint32_t UserType, uint32_t UserConfig)
+{
+ uint32_t optr_reg_val = 0;
+ uint32_t optr_reg_mask = 0;
+
+ /* Check the parameters */
+ assert_param(IS_OB_USER_TYPE(UserType));
+
+ if((UserType & OB_USER_IWDG1_SW) != 0U)
+ {
+ /* IWDG_HW option byte should be modified */
+ assert_param(IS_OB_IWDG1_SOURCE(UserConfig & FLASH_OPTSR_IWDG1_SW));
+
+ /* Set value and mask for IWDG_HW option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_IWDG1_SW);
+ optr_reg_mask |= FLASH_OPTSR_IWDG1_SW;
+ }
+#if defined(DUAL_CORE)
+ if((UserType & OB_USER_IWDG2_SW) != 0U)
+ {
+ /* IWDG2_SW option byte should be modified */
+ assert_param(IS_OB_IWDG2_SOURCE(UserConfig & FLASH_OPTSR_IWDG2_SW));
+
+ /* Set value and mask for IWDG2_SW option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_IWDG2_SW);
+ optr_reg_mask |= FLASH_OPTSR_IWDG2_SW;
+ }
+#endif /*DUAL_CORE*/
+ if((UserType & OB_USER_NRST_STOP_D1) != 0U)
+ {
+ /* NRST_STOP option byte should be modified */
+ assert_param(IS_OB_STOP_D1_RESET(UserConfig & FLASH_OPTSR_NRST_STOP_D1));
+
+ /* Set value and mask for NRST_STOP option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STOP_D1);
+ optr_reg_mask |= FLASH_OPTSR_NRST_STOP_D1;
+ }
+
+ if((UserType & OB_USER_NRST_STDBY_D1) != 0U)
+ {
+ /* NRST_STDBY option byte should be modified */
+ assert_param(IS_OB_STDBY_D1_RESET(UserConfig & FLASH_OPTSR_NRST_STBY_D1));
+
+ /* Set value and mask for NRST_STDBY option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STBY_D1);
+ optr_reg_mask |= FLASH_OPTSR_NRST_STBY_D1;
+ }
+
+ if((UserType & OB_USER_IWDG_STOP) != 0U)
+ {
+ /* IWDG_STOP option byte should be modified */
+ assert_param(IS_OB_USER_IWDG_STOP(UserConfig & FLASH_OPTSR_FZ_IWDG_STOP));
+
+ /* Set value and mask for IWDG_STOP option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_FZ_IWDG_STOP);
+ optr_reg_mask |= FLASH_OPTSR_FZ_IWDG_STOP;
+ }
+
+ if((UserType & OB_USER_IWDG_STDBY) != 0U)
+ {
+ /* IWDG_STDBY option byte should be modified */
+ assert_param(IS_OB_USER_IWDG_STDBY(UserConfig & FLASH_OPTSR_FZ_IWDG_SDBY));
+
+ /* Set value and mask for IWDG_STDBY option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_FZ_IWDG_SDBY);
+ optr_reg_mask |= FLASH_OPTSR_FZ_IWDG_SDBY;
+ }
+
+ if((UserType & OB_USER_ST_RAM_SIZE) != 0U)
+ {
+ /* ST_RAM_SIZE option byte should be modified */
+ assert_param(IS_OB_USER_ST_RAM_SIZE(UserConfig & FLASH_OPTSR_ST_RAM_SIZE));
+
+ /* Set value and mask for ST_RAM_SIZE option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_ST_RAM_SIZE);
+ optr_reg_mask |= FLASH_OPTSR_ST_RAM_SIZE;
+ }
+
+ if((UserType & OB_USER_SECURITY) != 0U)
+ {
+ /* SECURITY option byte should be modified */
+ assert_param(IS_OB_USER_SECURITY(UserConfig & FLASH_OPTSR_SECURITY));
+
+ /* Set value and mask for SECURITY option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_SECURITY);
+ optr_reg_mask |= FLASH_OPTSR_SECURITY;
+ }
+
+#if defined(DUAL_CORE)
+ if((UserType & OB_USER_BCM4) != 0U)
+ {
+ /* BCM4 option byte should be modified */
+ assert_param(IS_OB_USER_BCM4(UserConfig & FLASH_OPTSR_BCM4));
+
+ /* Set value and mask for BCM4 option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_BCM4);
+ optr_reg_mask |= FLASH_OPTSR_BCM4;
+ }
+
+ if((UserType & OB_USER_BCM7) != 0U)
+ {
+ /* BCM7 option byte should be modified */
+ assert_param(IS_OB_USER_BCM7(UserConfig & FLASH_OPTSR_BCM7));
+
+ /* Set value and mask for BCM7 option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_BCM7);
+ optr_reg_mask |= FLASH_OPTSR_BCM7;
+ }
+#endif /* DUAL_CORE */
+
+#if defined (FLASH_OPTSR_NRST_STOP_D2)
+ if((UserType & OB_USER_NRST_STOP_D2) != 0U)
+ {
+ /* NRST_STOP option byte should be modified */
+ assert_param(IS_OB_STOP_D2_RESET(UserConfig & FLASH_OPTSR_NRST_STOP_D2));
+
+ /* Set value and mask for NRST_STOP option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STOP_D2);
+ optr_reg_mask |= FLASH_OPTSR_NRST_STOP_D2;
+ }
+
+ if((UserType & OB_USER_NRST_STDBY_D2) != 0U)
+ {
+ /* NRST_STDBY option byte should be modified */
+ assert_param(IS_OB_STDBY_D2_RESET(UserConfig & FLASH_OPTSR_NRST_STBY_D2));
+
+ /* Set value and mask for NRST_STDBY option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_NRST_STBY_D2);
+ optr_reg_mask |= FLASH_OPTSR_NRST_STBY_D2;
+ }
+#endif /* FLASH_OPTSR_NRST_STOP_D2 */
+
+#if defined (DUAL_BANK)
+ if((UserType & OB_USER_SWAP_BANK) != 0U)
+ {
+ /* SWAP_BANK_OPT option byte should be modified */
+ assert_param(IS_OB_USER_SWAP_BANK(UserConfig & FLASH_OPTSR_SWAP_BANK_OPT));
+
+ /* Set value and mask for SWAP_BANK_OPT option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_SWAP_BANK_OPT);
+ optr_reg_mask |= FLASH_OPTSR_SWAP_BANK_OPT;
+ }
+#endif /* DUAL_BANK */
+
+ if((UserType & OB_USER_IOHSLV) != 0U)
+ {
+ /* IOHSLV_OPT option byte should be modified */
+ assert_param(IS_OB_USER_IOHSLV(UserConfig & FLASH_OPTSR_IO_HSLV));
+
+ /* Set value and mask for IOHSLV_OPT option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_IO_HSLV);
+ optr_reg_mask |= FLASH_OPTSR_IO_HSLV;
+ }
+
+#if defined (FLASH_OPTSR_VDDMMC_HSLV)
+ if((UserType & OB_USER_VDDMMC_HSLV) != 0U)
+ {
+ /* VDDMMC_HSLV option byte should be modified */
+ assert_param(IS_OB_USER_VDDMMC_HSLV(UserConfig & FLASH_OPTSR_VDDMMC_HSLV));
+
+ /* Set value and mask for VDDMMC_HSLV option byte */
+ optr_reg_val |= (UserConfig & FLASH_OPTSR_VDDMMC_HSLV);
+ optr_reg_mask |= FLASH_OPTSR_VDDMMC_HSLV;
+ }
+#endif /* FLASH_OPTSR_VDDMMC_HSLV */
+
+ /* Configure the option bytes register */
+ MODIFY_REG(FLASH->OPTSR_PRG, optr_reg_mask, optr_reg_val);
+}
+
+#if defined(DUAL_CORE)
+/**
+ * @brief Return the FLASH User Option Byte value.
+ * @retval The FLASH User Option Bytes values
+ * IWDG1_SW(Bit4), IWDG2_SW(Bit 5), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
+ * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
+ * SECURITY(Bit 21), BCM4(Bit 22), BCM7(Bit 23), nRST_STOP_D2(Bit 24),
+ * nRST_STDY_D2(Bit 25), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
+ */
+#else
+/**
+ * @brief Return the FLASH User Option Byte value.
+ * @retval The FLASH User Option Bytes values
+ * IWDG_SW(Bit4), nRST_STOP_D1(Bit 6), nRST_STDY_D1(Bit 7),
+ * FZ_IWDG_STOP(Bit 17), FZ_IWDG_SDBY(Bit 18), ST_RAM_SIZE(Bit[19:20]),
+ * SECURITY(Bit 21), IO_HSLV (Bit 29) and SWAP_BANK_OPT(Bit 31).
+ */
+#endif /*DUAL_CORE*/
+static uint32_t FLASH_OB_GetUser(void)
+{
+ uint32_t userConfig = READ_REG(FLASH->OPTSR_CUR);
+ userConfig &= (~(FLASH_OPTSR_BOR_LEV | FLASH_OPTSR_RDP));
+
+ return userConfig;
+}
+
+/**
+ * @brief Configure the Proprietary code readout protection of the desired addresses
+ *
+ * @note To configure the PCROP options, the option lock bit OPTLOCK must be
+ * cleared with the call of the HAL_FLASH_OB_Unlock() function.
+ * @note To validate the PCROP options, the option bytes must be reloaded
+ * through the call of the HAL_FLASH_OB_Launch() function.
+ *
+ * @param PCROPConfig specifies if the PCROP area for the given Bank shall be erased or not
+ * when RDP level decreased from Level 1 to Level 0, or after a bank erase with protection removal
+ * This parameter must be a value of @arg FLASHEx_OB_PCROP_RDP enumeration
+ *
+ * @param PCROPStartAddr specifies the start address of the Proprietary code readout protection
+ * This parameter can be an address between begin and end of the bank
+ *
+ * @param PCROPEndAddr specifies the end address of the Proprietary code readout protection
+ * This parameter can be an address between PCROPStartAddr and end of the bank
+ *
+ * @param Banks the specific bank to apply PCROP protection
+ * This parameter can be one of the following values:
+ * @arg FLASH_BANK_1: PCROP on specified bank1 area
+ * @arg FLASH_BANK_2: PCROP on specified bank2 area
+ * @arg FLASH_BANK_BOTH: PCROP on specified bank1 and bank2 area (same config will be applied on both banks)
+ *
+ * @retval None
+ */
+static void FLASH_OB_PCROPConfig(uint32_t PCROPConfig, uint32_t PCROPStartAddr, uint32_t PCROPEndAddr, uint32_t Banks)
+{
+ /* Check the parameters */
+ assert_param(IS_FLASH_BANK(Banks));
+ assert_param(IS_OB_PCROP_RDP(PCROPConfig));
+
+ if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(PCROPStartAddr));
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(PCROPEndAddr));
+
+ /* Configure the Proprietary code readout protection */
+ FLASH->PRAR_PRG1 = ((PCROPStartAddr - FLASH_BANK1_BASE) >> 8) | \
+ (((PCROPEndAddr - FLASH_BANK1_BASE) >> 8) << FLASH_PRAR_PROT_AREA_END_Pos) | \
+ PCROPConfig;
+ }
+
+#if defined (DUAL_BANK)
+ if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(PCROPStartAddr));
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(PCROPEndAddr));
+
+ /* Configure the Proprietary code readout protection */
+ FLASH->PRAR_PRG2 = ((PCROPStartAddr - FLASH_BANK2_BASE) >> 8) | \
+ (((PCROPEndAddr - FLASH_BANK2_BASE) >> 8) << FLASH_PRAR_PROT_AREA_END_Pos) | \
+ PCROPConfig;
+ }
+#endif /* DUAL_BANK */
+}
+
+/**
+ * @brief Get the Proprietary code readout protection configuration on a given Bank
+ *
+ * @param PCROPConfig indicates if the PCROP area for the given Bank shall be erased or not
+ * when RDP level decreased from Level 1 to Level 0 or after a bank erase with protection removal
+ *
+ * @param PCROPStartAddr gives the start address of the Proprietary code readout protection of the bank
+ *
+ * @param PCROPEndAddr gives the end address of the Proprietary code readout protection of the bank
+ *
+ * @param Bank the specific bank to apply PCROP protection
+ * This parameter can be exclusively one of the following values:
+ * @arg FLASH_BANK_1: PCROP on specified bank1 area
+ * @arg FLASH_BANK_2: PCROP on specified bank2 area
+ * @arg FLASH_BANK_BOTH: is not allowed here
+ *
+ * @retval None
+ */
+static void FLASH_OB_GetPCROP(uint32_t *PCROPConfig, uint32_t *PCROPStartAddr, uint32_t *PCROPEndAddr, uint32_t Bank)
+{
+ uint32_t regvalue = 0;
+ uint32_t bankBase = 0;
+
+ if(Bank == FLASH_BANK_1)
+ {
+ regvalue = FLASH->PRAR_CUR1;
+ bankBase = FLASH_BANK1_BASE;
+ }
+
+#if defined (DUAL_BANK)
+ if(Bank == FLASH_BANK_2)
+ {
+ regvalue = FLASH->PRAR_CUR2;
+ bankBase = FLASH_BANK2_BASE;
+ }
+#endif /* DUAL_BANK */
+
+ (*PCROPConfig) = (regvalue & FLASH_PRAR_DMEP);
+
+ (*PCROPStartAddr) = ((regvalue & FLASH_PRAR_PROT_AREA_START) << 8) + bankBase;
+ (*PCROPEndAddr) = (regvalue & FLASH_PRAR_PROT_AREA_END) >> FLASH_PRAR_PROT_AREA_END_Pos;
+ (*PCROPEndAddr) = ((*PCROPEndAddr) << 8) + bankBase;
+}
+
+/**
+ * @brief Set the BOR Level.
+ * @param Level specifies the Option Bytes BOR Reset Level.
+ * This parameter can be one of the following values:
+ * @arg OB_BOR_LEVEL0: Reset level threshold is set to 1.6V
+ * @arg OB_BOR_LEVEL1: Reset level threshold is set to 2.1V
+ * @arg OB_BOR_LEVEL2: Reset level threshold is set to 2.4V
+ * @arg OB_BOR_LEVEL3: Reset level threshold is set to 2.7V
+ * @retval None
+ */
+static void FLASH_OB_BOR_LevelConfig(uint32_t Level)
+{
+ assert_param(IS_OB_BOR_LEVEL(Level));
+
+ /* Configure BOR_LEV option byte */
+ MODIFY_REG(FLASH->OPTSR_PRG, FLASH_OPTSR_BOR_LEV, Level);
+}
+
+/**
+ * @brief Get the BOR Level.
+ * @retval The Option Bytes BOR Reset Level.
+ * This parameter can be one of the following values:
+ * @arg OB_BOR_LEVEL0: Reset level threshold is set to 1.6V
+ * @arg OB_BOR_LEVEL1: Reset level threshold is set to 2.1V
+ * @arg OB_BOR_LEVEL2: Reset level threshold is set to 2.4V
+ * @arg OB_BOR_LEVEL3: Reset level threshold is set to 2.7V
+ */
+static uint32_t FLASH_OB_GetBOR(void)
+{
+ return (FLASH->OPTSR_CUR & FLASH_OPTSR_BOR_LEV);
+}
+
+/**
+ * @brief Set Boot address
+ * @param BootOption Boot address option byte to be programmed,
+ * This parameter must be a value of @ref FLASHEx_OB_BOOT_OPTION
+ (OB_BOOT_ADD0, OB_BOOT_ADD1 or OB_BOOT_ADD_BOTH)
+ *
+ * @param BootAddress0 Specifies the Boot Address 0
+ * @param BootAddress1 Specifies the Boot Address 1
+ * @retval HAL Status
+ */
+static void FLASH_OB_BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_BOOT_ADD_OPTION(BootOption));
+
+ if((BootOption & OB_BOOT_ADD0) == OB_BOOT_ADD0)
+ {
+ /* Check the parameters */
+ assert_param(IS_BOOT_ADDRESS(BootAddress0));
+
+ /* Configure CM7 BOOT ADD0 */
+#if defined(DUAL_CORE)
+ MODIFY_REG(FLASH->BOOT7_PRG, FLASH_BOOT7_BCM7_ADD0, (BootAddress0 >> 16));
+#else /* Single Core*/
+ MODIFY_REG(FLASH->BOOT_PRG, FLASH_BOOT_ADD0, (BootAddress0 >> 16));
+#endif /* DUAL_CORE */
+ }
+
+ if((BootOption & OB_BOOT_ADD1) == OB_BOOT_ADD1)
+ {
+ /* Check the parameters */
+ assert_param(IS_BOOT_ADDRESS(BootAddress1));
+
+ /* Configure CM7 BOOT ADD1 */
+#if defined(DUAL_CORE)
+ MODIFY_REG(FLASH->BOOT7_PRG, FLASH_BOOT7_BCM7_ADD1, BootAddress1);
+#else /* Single Core*/
+ MODIFY_REG(FLASH->BOOT_PRG, FLASH_BOOT_ADD1, BootAddress1);
+#endif /* DUAL_CORE */
+ }
+}
+
+/**
+ * @brief Get Boot address
+ * @param BootAddress0 Specifies the Boot Address 0.
+ * @param BootAddress1 Specifies the Boot Address 1.
+ * @retval HAL Status
+ */
+static void FLASH_OB_GetBootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1)
+{
+ uint32_t regvalue;
+
+#if defined(DUAL_CORE)
+ regvalue = FLASH->BOOT7_CUR;
+
+ (*BootAddress0) = (regvalue & FLASH_BOOT7_BCM7_ADD0) << 16;
+ (*BootAddress1) = (regvalue & FLASH_BOOT7_BCM7_ADD1);
+#else /* Single Core */
+ regvalue = FLASH->BOOT_CUR;
+
+ (*BootAddress0) = (regvalue & FLASH_BOOT_ADD0) << 16;
+ (*BootAddress1) = (regvalue & FLASH_BOOT_ADD1);
+#endif /* DUAL_CORE */
+}
+
+#if defined(DUAL_CORE)
+/**
+ * @brief Set CM4 Boot address
+ * @param BootOption Boot address option byte to be programmed,
+ * This parameter must be a value of @ref FLASHEx_OB_BOOT_OPTION
+ (OB_BOOT_ADD0, OB_BOOT_ADD1 or OB_BOOT_ADD_BOTH)
+ *
+ * @param BootAddress0 Specifies the CM4 Boot Address 0.
+ * @param BootAddress1 Specifies the CM4 Boot Address 1.
+ * @retval HAL Status
+ */
+static void FLASH_OB_CM4BootAddConfig(uint32_t BootOption, uint32_t BootAddress0, uint32_t BootAddress1)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_BOOT_ADD_OPTION(BootOption));
+
+ if((BootOption & OB_BOOT_ADD0) == OB_BOOT_ADD0)
+ {
+ /* Check the parameters */
+ assert_param(IS_BOOT_ADDRESS(BootAddress0));
+
+ /* Configure CM4 BOOT ADD0 */
+ MODIFY_REG(FLASH->BOOT4_PRG, FLASH_BOOT4_BCM4_ADD0, (BootAddress0 >> 16));
+
+ }
+
+ if((BootOption & OB_BOOT_ADD1) == OB_BOOT_ADD1)
+ {
+ /* Check the parameters */
+ assert_param(IS_BOOT_ADDRESS(BootAddress1));
+
+ /* Configure CM4 BOOT ADD1 */
+ MODIFY_REG(FLASH->BOOT4_PRG, FLASH_BOOT4_BCM4_ADD1, BootAddress1);
+ }
+}
+
+/**
+ * @brief Get CM4 Boot address
+ * @param BootAddress0 Specifies the CM4 Boot Address 0.
+ * @param BootAddress1 Specifies the CM4 Boot Address 1.
+ * @retval HAL Status
+ */
+static void FLASH_OB_GetCM4BootAdd(uint32_t *BootAddress0, uint32_t *BootAddress1)
+{
+ uint32_t regvalue;
+
+ regvalue = FLASH->BOOT4_CUR;
+
+ (*BootAddress0) = (regvalue & FLASH_BOOT4_BCM4_ADD0) << 16;
+ (*BootAddress1) = (regvalue & FLASH_BOOT4_BCM4_ADD1);
+}
+#endif /*DUAL_CORE*/
+
+/**
+ * @brief Set secure area configuration
+ * @param SecureAreaConfig specify if the secure area will be deleted or not
+ * when RDP level decreased from Level 1 to Level 0 or during a mass erase.
+ *
+ * @param SecureAreaStartAddr Specifies the secure area start address
+ * @param SecureAreaEndAddr Specifies the secure area end address
+ * @param Banks the specific bank to apply Security protection
+ * This parameter can be one of the following values:
+ * @arg FLASH_BANK_1: Secure area on specified bank1 area
+ * @arg FLASH_BANK_2: Secure area on specified bank2 area
+ * @arg FLASH_BANK_BOTH: Secure area on specified bank1 and bank2 area (same config will be applied on both banks)
+ * @retval None
+ */
+static void FLASH_OB_SecureAreaConfig(uint32_t SecureAreaConfig, uint32_t SecureAreaStartAddr, uint32_t SecureAreaEndAddr, uint32_t Banks)
+{
+ /* Check the parameters */
+ assert_param(IS_FLASH_BANK(Banks));
+ assert_param(IS_OB_SECURE_RDP(SecureAreaConfig));
+
+ if((Banks & FLASH_BANK_1) == FLASH_BANK_1)
+ {
+ /* Check the parameters */
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(SecureAreaStartAddr));
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(SecureAreaEndAddr));
+
+ /* Configure the secure area */
+ FLASH->SCAR_PRG1 = ((SecureAreaStartAddr - FLASH_BANK1_BASE) >> 8) | \
+ (((SecureAreaEndAddr - FLASH_BANK1_BASE) >> 8) << FLASH_SCAR_SEC_AREA_END_Pos) | \
+ (SecureAreaConfig & FLASH_SCAR_DMES);
+ }
+
+#if defined (DUAL_BANK)
+ if((Banks & FLASH_BANK_2) == FLASH_BANK_2)
+ {
+ /* Check the parameters */
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(SecureAreaStartAddr));
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(SecureAreaEndAddr));
+
+ /* Configure the secure area */
+ FLASH->SCAR_PRG2 = ((SecureAreaStartAddr - FLASH_BANK2_BASE) >> 8) | \
+ (((SecureAreaEndAddr - FLASH_BANK2_BASE) >> 8) << FLASH_SCAR_SEC_AREA_END_Pos) | \
+ (SecureAreaConfig & FLASH_SCAR_DMES);
+ }
+#endif /* DUAL_BANK */
+}
+
+/**
+ * @brief Get secure area configuration
+ * @param SecureAreaConfig indicates if the secure area will be deleted or not
+ * when RDP level decreased from Level 1 to Level 0 or during a mass erase.
+ * @param SecureAreaStartAddr gives the secure area start address
+ * @param SecureAreaEndAddr gives the secure area end address
+ * @param Bank Specifies the Bank
+ * @retval None
+ */
+static void FLASH_OB_GetSecureArea(uint32_t *SecureAreaConfig, uint32_t *SecureAreaStartAddr, uint32_t *SecureAreaEndAddr, uint32_t Bank)
+{
+ uint32_t regvalue = 0;
+ uint32_t bankBase = 0;
+
+ /* Check Bank parameter value */
+ if(Bank == FLASH_BANK_1)
+ {
+ regvalue = FLASH->SCAR_CUR1;
+ bankBase = FLASH_BANK1_BASE;
+ }
+
+#if defined (DUAL_BANK)
+ if(Bank == FLASH_BANK_2)
+ {
+ regvalue = FLASH->SCAR_CUR2;
+ bankBase = FLASH_BANK2_BASE;
+ }
+#endif /* DUAL_BANK */
+
+ /* Get the secure area settings */
+ (*SecureAreaConfig) = (regvalue & FLASH_SCAR_DMES);
+ (*SecureAreaStartAddr) = ((regvalue & FLASH_SCAR_SEC_AREA_START) << 8) + bankBase;
+ (*SecureAreaEndAddr) = (regvalue & FLASH_SCAR_SEC_AREA_END) >> FLASH_SCAR_SEC_AREA_END_Pos;
+ (*SecureAreaEndAddr) = ((*SecureAreaEndAddr) << 8) + bankBase;
+}
+
+/**
+ * @brief Add a CRC sector to the list of sectors on which the CRC will be calculated
+ * @param Sector Specifies the CRC sector number
+ * @param Bank Specifies the Bank
+ * @retval None
+ */
+static void FLASH_CRC_AddSector(uint32_t Sector, uint32_t Bank)
+{
+ /* Check the parameters */
+ assert_param(IS_FLASH_SECTOR(Sector));
+
+ if (Bank == FLASH_BANK_1)
+ {
+ /* Clear CRC sector */
+ FLASH->CRCCR1 &= (~FLASH_CRCCR_CRC_SECT);
+
+ /* Select CRC Sector and activate ADD_SECT bit */
+ FLASH->CRCCR1 |= Sector | FLASH_CRCCR_ADD_SECT;
+ }
+#if defined (DUAL_BANK)
+ else
+ {
+ /* Clear CRC sector */
+ FLASH->CRCCR2 &= (~FLASH_CRCCR_CRC_SECT);
+
+ /* Select CRC Sector and activate ADD_SECT bit */
+ FLASH->CRCCR2 |= Sector | FLASH_CRCCR_ADD_SECT;
+ }
+#endif /* DUAL_BANK */
+}
+
+/**
+ * @brief Select CRC start and end memory addresses on which the CRC will be calculated
+ * @param CRCStartAddr Specifies the CRC start address
+ * @param CRCEndAddr Specifies the CRC end address
+ * @param Bank Specifies the Bank
+ * @retval None
+ */
+static void FLASH_CRC_SelectAddress(uint32_t CRCStartAddr, uint32_t CRCEndAddr, uint32_t Bank)
+{
+ if (Bank == FLASH_BANK_1)
+ {
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(CRCStartAddr));
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK1(CRCEndAddr));
+
+ /* Write CRC Start and End addresses */
+ FLASH->CRCSADD1 = CRCStartAddr;
+ FLASH->CRCEADD1 = CRCEndAddr;
+ }
+#if defined (DUAL_BANK)
+ else
+ {
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(CRCStartAddr));
+ assert_param(IS_FLASH_PROGRAM_ADDRESS_BANK2(CRCEndAddr));
+
+ /* Write CRC Start and End addresses */
+ FLASH->CRCSADD2 = CRCStartAddr;
+ FLASH->CRCEADD2 = CRCEndAddr;
+ }
+#endif /* DUAL_BANK */
+}
+/**
+ * @}
+ */
+
+#if defined (FLASH_OTPBL_LOCKBL)
+/**
+ * @brief Configure the OTP Block Lock.
+ * @param OTP_Block specifies the OTP Block to lock.
+ * This parameter can be a value of @ref FLASHEx_OTP_Blocks
+ * @retval None
+ */
+static void FLASH_OB_OTP_LockConfig(uint32_t OTP_Block)
+{
+ /* Check the parameters */
+ assert_param(IS_OTP_BLOCK(OTP_Block));
+
+ /* Configure the OTP Block lock in the option bytes register */
+ FLASH->OTPBL_PRG |= (OTP_Block & FLASH_OTPBL_LOCKBL);
+}
+
+/**
+ * @brief Get the OTP Block Lock.
+ * @retval OTP_Block specifies the OTP Block to lock.
+ * This return value can be a value of @ref FLASHEx_OTP_Blocks
+ */
+static uint32_t FLASH_OB_OTP_GetLock(void)
+{
+ return (FLASH->OTPBL_CUR);
+}
+#endif /* FLASH_OTPBL_LOCKBL */
+
+#if defined (FLASH_OPTSR2_TCM_AXI_SHARED)
+/**
+ * @brief Configure the TCM / AXI Shared RAM.
+ * @param SharedRamConfig specifies the Shared RAM configuration.
+ * This parameter can be a value of @ref FLASHEx_OB_TCM_AXI_SHARED
+ * @retval None
+ */
+static void FLASH_OB_SharedRAM_Config(uint32_t SharedRamConfig)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_USER_TCM_AXI_SHARED(SharedRamConfig));
+
+ /* Configure the TCM / AXI Shared RAM in the option bytes register */
+ MODIFY_REG(FLASH->OPTSR2_PRG, FLASH_OPTSR2_TCM_AXI_SHARED, SharedRamConfig);
+}
+
+/**
+ * @brief Get the TCM / AXI Shared RAM configuration.
+ * @retval SharedRamConfig returns the TCM / AXI Shared RAM configuration.
+ * This return value can be a value of @ref FLASHEx_OB_TCM_AXI_SHARED
+ */
+static uint32_t FLASH_OB_SharedRAM_GetConfig(void)
+{
+ return (FLASH->OPTSR2_CUR & FLASH_OPTSR2_TCM_AXI_SHARED);
+}
+#endif /* FLASH_OPTSR2_TCM_AXI_SHARED */
+
+#if defined (FLASH_OPTSR2_CPUFREQ_BOOST)
+/**
+ * @brief Configure the CPU Frequency Boost.
+ * @param FreqBoost specifies the CPU Frequency Boost state.
+ * This parameter can be a value of @ref FLASHEx_OB_CPUFREQ_BOOST
+ * @retval None
+ */
+static void FLASH_OB_CPUFreq_BoostConfig(uint32_t FreqBoost)
+{
+ /* Check the parameters */
+ assert_param(IS_OB_USER_CPUFREQ_BOOST(FreqBoost));
+
+ /* Configure the CPU Frequency Boost in the option bytes register */
+ MODIFY_REG(FLASH->OPTSR2_PRG, FLASH_OPTSR2_CPUFREQ_BOOST, FreqBoost);
+}
+
+/**
+ * @brief Get the CPU Frequency Boost state.
+ * @retval FreqBoost returns the CPU Frequency Boost state.
+ * This return value can be a value of @ref FLASHEx_OB_CPUFREQ_BOOST
+ */
+static uint32_t FLASH_OB_CPUFreq_GetBoost(void)
+{
+ return (FLASH->OPTSR2_CUR & FLASH_OPTSR2_CPUFREQ_BOOST);
+}
+#endif /* FLASH_OPTSR2_CPUFREQ_BOOST */
+
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+