summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--make/ChangeLog4
-rw-r--r--make/custom/mbx8xx.cfg35
2 files changed, 25 insertions, 14 deletions
diff --git a/make/ChangeLog b/make/ChangeLog
index 7708232300..deedbfff87 100644
--- a/make/ChangeLog
+++ b/make/ChangeLog
@@ -1,4 +1,8 @@
+2000-08-11 Charles-Antoine Gauthier <charles.gauthier@nrc.ca>
+
+ * custom/mbx8xx.cfg: Add support for configuration parameters in NVRAM
+
2000-08-25 Joel Sherrill <joel.sherrill@OARcorp.com>
* ChangeLog: File paths corrected.
diff --git a/make/custom/mbx8xx.cfg b/make/custom/mbx8xx.cfg
index ee1ff20a4e..b4566046e1 100644
--- a/make/custom/mbx8xx.cfg
+++ b/make/custom/mbx8xx.cfg
@@ -64,6 +64,15 @@ endif # mbx821
#
# MBX8xx-specific options:
#
+# NVRAM_CONFIGURE
+# Define to 1 if you want the console driver, network driver and caches
+# configured at boot time from parameters stored in NVRAM. If set to 1,
+# most parameters below are ignored during the build. If not set to 1,
+# then the console driver is configured at build time, the network host
+# information is obtained from application supplied data structures, and
+# the caches are configured at boot time based on the information supplied
+# in this file.
+#
# UARTS_USE_TERMIOS
# Define to 1 if you want termios support for every port.
# Termios support is independent of the choice of UART I/O mode.
@@ -74,7 +83,7 @@ endif # mbx821
# as /dev/console.
#
# UARTS_IO_MODE (BSP--console driver)
-# Define to 0 if you want polled I/O performed by RTEMS.
+# Define to 0 or 1 if you want polled I/O performed by RTEMS.
# Define to 1 if you want interrupt-driven performed by RTEMS.
# Define to 2 if you want polled I/O performed by EPPCBug.
# There is no provision to have a mix of interrupt-driven and polled I/O
@@ -94,25 +103,18 @@ endif # mbx821
# each other.
#
# PRINTK_IO_MODE (BSP--console driver)
-# Define to 0 if you want polled I/O performed by RTEMS.
-# Define to 1 if you want interrupt-driven I/O performed by RTEMS.
+# Define to 0 or 1 if you want polled I/O performed by RTEMS.
# Define to 2 if you want polled I/O performed by EPPCBug.
-# The printk() port is not configured to termios. The only way to
-# use printk() with interrupt-driven I/O, which always uses termios,
-# is to open the printk port from an RTEMS application. One way to
-# do this is to have PRINTK_MINOR == CONSOLE_MINOR. With EPPCBug 1.1,
+# The printk() port is not configured to use termios. With EPPCBug 1.1,
# if mode 2 is selected, PRINTK_MINOR must be set to SMC1_MINOR.
# This is a deficiency of the firmware: it does not perform serial I/O
# on any port other than its default debug port, which must be SMC1.
+# Printk always uses polled output.
#
# EPPCBUG_SMC1 (BSP--console driver)
# If defined, SMC1 is in use by EPPC-Bug. The console driver will not
# re-initialize that port.
#
-# EPPCBUG_VECTORS (BSP--RTEMS)
-# If defined, vectors branch to EPPCBug, except the following:
-# 0x500 (external interrupt), 0x900 (decrementer).
-#
# INSTRUCTION_CACHE_ENABLE (BSP--RTEMS)
# If defined, the instruction cache will be enabled after address translation
# is turned on.
@@ -121,6 +123,10 @@ endif # mbx821
# If defined, the data cache will be enabled after address translation
# is turned on.
#
+# EPPCBUG_VECTORS (BSP--RTEMS)
+# If defined, vectors branch to EPPCBug, except the following:
+# 0x500 (external interrupt), 0x900 (decrementer).
+#
# PowerPC-specific options:
#
# PPC_USE_SPRG (RTEMS PowerPC port)
@@ -128,7 +134,7 @@ endif # mbx821
# of the special purpose registers to slightly optimize interrupt
# response time. The use of these registers can conflict with
# other tools like debuggers. This should be 0 when using EPPCBug
-# because its uses most SPRGs (don't believe the documentation!).
+# because its uses most SPRGs (do not believe the documentation!).
#
# PPC_USE_DATA_CACHE (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use
@@ -141,11 +147,12 @@ define make-target-options
@echo "#endif" >>$@
@echo "#define mpc$(CPU_TYPE) 1" >>$@
@echo >>$@
- @echo "#define UARTS_USE_TERMIOS 1" >>$@
+ @echo "#define NVRAM_CONFIGURE 1" >>$@
+ @echo "#define UARTS_USE_TERMIOS 0" >>$@
@echo "#define CONSOLE_MINOR SMC2_MINOR" >>$@
@echo "#define UARTS_IO_MODE 0" >>$@
@echo "#define PRINTK_MINOR SMC2_MINOR" >>$@
- @echo "#define PRINTK_IO_MODE 0" >>$@
+ @echo "#define PRINTK_IO_MODE 0" >>$@
@echo "#define EPPCBUG_SMC1 1" >>$@
@echo "#define EPPCBUG_VECTORS 1" >>$@
@echo "#define INSTRUCTION_CACHE_ENABLE 1" >>$@