cat /tmp/j | while read f

do
  rpm -qi $f 2>&1 | grep -v "is not ins"
done

5 files changed, 0 insertions, 193 deletions

diff --git a/c/src/lib/libchip/serial/README b/c/src/lib/libchip/serial/README
deleted file mode 100644
index 3a1013b45b..0000000000
--- a/c/src/lib/libchip/serial/README
+++ /dev/null
@@ -1,17 +0,0 @@
-#
-#  $Id$
-#
-
-This is the serial controller portion of the libchip library.  This 
-directory contains the source code for reusable console driver
-support code.  Each individual driver is configured using the
-console_tbl data structure.  This structure is defined and explained
-in the console.h file.
-
-The reusable chip drivers do not directly access the serial controller.
-They access the registers on the controller via a set of up to four 
-functions which are provided by the BSP.  These functins set and get
-general registers and data buffers.  Some chips can access the data
-buffers as general registers and thus the driver may not require
-those interface routines.
-
diff --git a/c/src/lib/libchip/serial/README.mc68681 b/c/src/lib/libchip/serial/README.mc68681
deleted file mode 100644
index 240faf759b..0000000000
--- a/c/src/lib/libchip/serial/README.mc68681
+++ /dev/null
@@ -1,87 +0,0 @@
-#
-#  $Id$
-#
-
-Configuration Table Use
-=======================
-
-sDeviceName
-
-   The name of this device.
-
-deviceType
-
-   This field must be SERIAL_MC68681.
-
-pDeviceFns
-
-   The device interface control table.  This may be:
-      + mc68681_fns for interrupt driven IO
-      + mc68681_fns_polled for polled IO
-
-deviceProbe
-
-   This is the address of the routine which probes to see if the device
-   is present.
-
-pDeviceFlow
-
-   This field is ignored as hardware flow control is not currently supported.
-
-ulMargin
-
-    This is currently unused.
-
-ulHysteresis
-
-    This is currently unused.
-
-pDeviceParams
-
-    This is set to the default settings.
-
-ulCtrlPort1
-
-   This field is the base address of the entire DUART.
-
-ulCtrlPort2
-
-   This field is the base address of the port specific registers.
-
-ulDataPort
-
-   This field is bit mapped as follows:
-     bit 0:  baud rate set a or b
-     bit 1-2: BRG selection ("Select Extend bit")
-
-   Note: If both ports on single DUART are not configured for the same
-         baud rate set, then unexpected results will occur.
-
-   Note: On the Exar 88c681, if a standard clock of 3.6864 Mhz is used
-         and the "Select Extend bit" is 0 (disabled), then the default
-         MC68681 baud rate table is selected.
-
-getRegister
-setRegister
-
-   These follow standard conventions.
-
-getData
-setData
-
-   These are unused since the TX and RX data registers can be accessed
-   as regular registers.
-
-ulClock
-
-   This is a pointer to a baud rate mapping table.  If set to
-   mc68681_baud_rate_table, then the CSR/ACR/X bit mappings shown
-   in the 68681 and 88681 manuals are used.  Otherwise, the board
-   specific baud rate mapping is used.
-
-   NULL is not a valid value.
-
-ulIntVector
-
-   This is the interrupt vector number associated with this chip.
-
diff --git a/c/src/lib/libchip/serial/README.ns16550 b/c/src/lib/libchip/serial/README.ns16550
deleted file mode 100644
index 2956173b1b..0000000000
--- a/c/src/lib/libchip/serial/README.ns16550
+++ /dev/null
@@ -1,5 +0,0 @@
-#
-#  $Id$
-#
-
-This driver needs to be debugged before this is written.
diff --git a/c/src/lib/libchip/serial/README.xr88681 b/c/src/lib/libchip/serial/README.xr88681
deleted file mode 100644
index 37364aaec6..0000000000
--- a/c/src/lib/libchip/serial/README.xr88681
+++ /dev/null
@@ -1,6 +0,0 @@
-#
-#  $Id$
-#
-
-The Exar XR88681 is an enhanced version of the Motorola MC68681 and is
-supported by the mc68681 driver.
diff --git a/c/src/lib/libchip/serial/README.z85c30 b/c/src/lib/libchip/serial/README.z85c30
deleted file mode 100644
index 4442b5ef40..0000000000
--- a/c/src/lib/libchip/serial/README.z85c30
+++ /dev/null
@@ -1,78 +0,0 @@
-#
-#  $Id$
-#
-
-Configuration Table Use
-=======================
-
-sDeviceName
-
-   The name of this device.
-
-deviceType
-
-   This field must be SERIAL_Z85C30.
-
-pDeviceFns
-
-   The device interface control table.  This may be:
-      + z85c30_fns for interrupt driven IO
-      + z85c30_fns_polled for polled IO
-
-deviceProbe
-
-   This is the address of the routine which probes to see if the device
-   is present.
-
-pDeviceFlow
-
-   This field is set to one of the following values:
-      + NULL for no hardware flow control
-      + z85c30_flow_RTSCTS for RTS/CTS based flow control
-      + z85c30_flow_DTRCTS for DTR/CTS based flow control
-
-ulMargin
-
-    This is currently unused.
-
-ulHysteresis
-
-    This is currently unused.
-
-pDeviceParams
-
-    This is set to the default settings.
-
-ulCtrlPort1
-
-   This field is the address of the control register for this port.
-
-ulCtrlPort2
-
-   This field is the address of the control register for chip.
-
-ulDataPort
-
-   This field is the address of the data register for this port.
-
-getRegister
-setRegister
-
-   These follow standard conventions.
-
-getData
-setData
-
-   These follow standard conventions.
-
-ulClock
-
-   This is the clock speed of the baud rate clock.
-   NULL, then the CSR/ACR/X bit mappings shown in the 68681 and 88681
-   manuals are used.  Otherwise, the board specific baud rate mapping
-   is used.
-
-ulIntVector
-
-   This is the interrupt vector number associated with this chip.
-