Revert "Add bspopts.h.in."

This reverts commit daffa606cc4a45d93c1f0f4fe365fde0fda6acbb.

Conflicts:

	c/src/lib/libbsp/arm/lpc24xx/include/bspopts.h.in
	c/src/lib/libbsp/powerpc/mpc55xxevb/include/bspopts.h.in
	c/src/lib/libbsp/powerpc/qoriq/include/bspopts.h.in

Manually deleted conflicting files.

1 files changed, 0 insertions, 93 deletions

diff --git a/c/src/lib/libbsp/powerpc/mbx8xx/include/bspopts.h.in b/c/src/lib/libbsp/powerpc/mbx8xx/include/bspopts.h.in
deleted file mode 100644
index 47d1b29142..0000000000
--- a/c/src/lib/libbsp/powerpc/mbx8xx/include/bspopts.h.in
+++ /dev/null
@@ -1,93 +0,0 @@
-/* include/bspopts.h.in.  Generated from configure.ac by autoheader.  */
-
-/* enables the data cache, if defined to a value other than zero */
-#undef BSP_DATA_CACHE_ENABLED
-
-/* If defined, then the BSP Framework will put a non-zero pattern into the
-   RTEMS Workspace and C program heap. This should assist in finding code that
-   assumes memory starts set to zero. */
-#undef BSP_DIRTY_MEMORY
-
-/* enables the instruction cache, if defined to a value other than zero */
-#undef BSP_INSTRUCTION_CACHE_ENABLED
-
-/* If defined, print a message and wait until pressed before resetting board
-   when application exits. */
-#undef BSP_PRESS_KEY_FOR_RESET
-
-/* If defined, reset the board when the application exits. */
-#undef BSP_RESET_BOARD_AT_EXIT
-
-/* (BSP--console driver) Must be defined to be one of SMC1_MINOR, SMC2_MINOR,
-   SCC2_MINOR, SCC3_MINOR, or SCC4_MINOR. Determines which device will be
-   registered as /dev/console. */
-#undef CONSOLE_MINOR
-
-/* used by irq/irq.c */
-#undef DISPATCH_HANDLER_STAT
-
-/* (BSP--console driver) If defined, SMC1 is in use by EPPC-Bug. The console
-   driver will not re-initialize that port. */
-#undef EPPCBUG_SMC1
-
-/* (BSP--RTEMS) If defined, vectors branch to EPPCBug, except the following:
-   0x500 (external interrupt), 0x900 (decrementer). */
-#undef EPPCBUG_VECTORS
-
-/* Define to 1 if you want the console driver, network driver and caches
-   configured at boot time from parameters stored in NVRAM. If set to 1, most
-   parameters below are ignored during the build. If not set to 1, then the
-   console driver is configured at build time, the network host information is
-   obtained from application supplied data structures, and the caches are
-   configured at boot time based on the information supplied in this file. */
-#undef NVRAM_CONFIGURE
-
-/* Define to the address where bug reports for this package should be sent. */
-#undef PACKAGE_BUGREPORT
-
-/* Define to the full name of this package. */
-#undef PACKAGE_NAME
-
-/* Define to the full name and version of this package. */
-#undef PACKAGE_STRING
-
-/* Define to the one symbol short name of this package. */
-#undef PACKAGE_TARNAME
-
-/* Define to the home page for this package. */
-#undef PACKAGE_URL
-
-/* Define to the version of this package. */
-#undef PACKAGE_VERSION
-
-/* (BSP--console driver) Define to 0 or 1 if you want polled I/O performed by
-   RTEMS. Define to 2 if you want polled I/O performed by EPPCBug. The
-   printk() port is not configured to use termios. With EPPCBug 1.1, if mode 2
-   is selected, PRINTK_MINOR must be set to SMC1_MINOR. This is a deficiency
-   of the firmware: it does not perform serial I/O on any port other than its
-   default debug port, which must be SMC1. Printk always uses polled output.
-   */
-#undef PRINTK_IO_MODE
-
-/* (BSP--console driver) Must be defined to be one of SMC1_MINOR, SMC2_MINOR,
-   SCC2_MINOR, SCC3_MINOR, or SCC4_MINOR. Determines which device is used for
-   output by printk(). If the port that printk() uses is also used for other
-   I/O (e.g. if PRINTK_MINOR == \$CONSOLE_MINOR), then both ports should use
-   the same type of I/O, otherwise the drivers will likely conflict with each
-   other. */
-#undef PRINTK_MINOR
-
-/* (BSP--console driver) Define to 0 or 1 if you want polled I/O performed by
-   RTEMS. Define to 1 if you want interrupt-driven performed by RTEMS. Define
-   to 2 if you want polled I/O performed by EPPCBug. There is no provision to
-   have a mix of interrupt-driven and polled I/O ports, except that the printk
-   port may use a different mode from the other ports. If this is done, do not
-   open the printk port from an RTEMS application. With EPPCBug 1.1, if mode 2
-   is selected, CONSOLE_MINOR must be set to SMC1_MINOR. This is a deficiency
-   of the firmware: it does not perform serial I/O on any port other than its
-   default debug port, which must be SMC1. */
-#undef UARTS_IO_MODE
-
-/* Define to 1 if you want termios support for every port. Termios support is
-   independent of the choice of UART I/O mode. */
-#undef UARTS_USE_TERMIOS