Obsolete and remove powerpc/mbx8xx

closes #2545.

1 files changed, 0 insertions, 1116 deletions

diff --git a/c/src/lib/libbsp/powerpc/mbx8xx/console/console.c b/c/src/lib/libbsp/powerpc/mbx8xx/console/console.c
deleted file mode 100644
index 6c7d593b9f..0000000000
--- a/c/src/lib/libbsp/powerpc/mbx8xx/console/console.c
+++ /dev/null
@@ -1,1116 +0,0 @@
-/*
- *  console.c
- *
- *  This file contains the MBX8xx termios serial I/O package.
- *  Only asynchronous I/O is supported.
- *
- *  The SCCs and SMCs are assigned as follows
- *
- *   Channel     Device      Minor   Note
- *    SMC1      /dev/tty0      0
- *    SMC2      /dev/tty1      1
- *    SCC1                     2     N/A. Hardwired as ethernet port
- *    SCC2      /dev/tty2      3
- *    SCC3      /dev/tty3      4
- *    SCC4      /dev/tty4      5
- *
- *  All ports support termios. The use of termios is recommended for real-time
- *  applications. Termios provides buffering and input processing. When not
- *  using termios, processing is limited to the substitution of LF for CR on
- *  input, and the output of a CR following the output of a LF character.
- *  Note that the terminal should not send CR/LF pairs when the return key
- *  is pressed, and that output lines are terminated with LF/CR, not CR/LF
- *  (although that would be easy to change).
- *
- *  I/O may be interrupt-driven (recommended for real-time applications) or
- *  polled. Polled I/O may be performed by this device driver entirely, or
- *  in part by EPPCBug. With EPPCBug 1.1, polled I/O is limited to the
- *  EPPCBug debug console. This is a limitation of the firmware. Later
- *  firmware may be able to do I/O through any port. This code assumes
- *  that the EPPCBug console is the default: SMC1. If the console and
- *  printk ports are set to anything else with EPPCBug polled I/O, the
- *  system will hang. Only port SMC1 is usable with EPPCBug polled I/O.
- *
- *  LIMITATIONS:
- *
- *  It is not possible to use different I/O modes on the different ports. The
- *  exception is with printk. The printk port can use a different mode from
- *  the other ports. If this is done, it is important not to open the printk
- *  port from an RTEMS application.
- *
- *  Currently, the I/O modes are determined at build time. It would be much
- *  better to have the mode selected at boot time based on parameters in
- *  NVRAM.
- *
- *  Interrupt-driven I/O requires termios.
- *
- *  TESTS:
- *
- *  TO RUN THE TESTS, USE POLLED I/O WITHOUT TERMIOS SUPPORT. Some tests
- *  play with the interrupt masks and turn off I/O. Those tests will hang
- *  when interrupt-driven I/O is used. Other tests, such as cdtest, do I/O
- *  from the static constructors before the console is open. This test
- *  will not work with interrupt-driven I/O. Because of the buffering
- *  performed in termios, test output may not be in sequence.The tests
- *  should all be fixed to work with interrupt-driven I/O and to
- *  produce output in the expected sequence. Obviously, the termios test
- *  requires termios support in the driver.
- *
- *  Set CONSOLE_MINOR to the appropriate device minor number in the
- *  config file. This allows the RTEMS application console to be different
- *  from the EPPBug debug console or the GDB port.
- *
- *  This driver handles all five available serial ports: it distinguishes
- *  the sub-devices using minor device numbers. It is not possible to have
- *  other protocols running on the other ports when this driver is used as
- *  currently written.
- *
- *  Based on code (alloc860.c in eth_comm port) by
- *  Jay Monkman (jmonkman@frasca.com),
- *  Copyright (C) 1998 by Frasca International, Inc.
- *
- *  Modifications by Darlene Stewart <Darlene.Stewart@iit.nrc.ca>
- *  and Charles-Antoine Gauthier <charles.gauthier@iit.nrc.ca>.
- *  Copyright (c) 2000, National Research Council of Canada
- *
- */
-#include <stdarg.h>
-#include <stdio.h>
-#include <bsp.h>                /* Must be before libio.h */
-#include <rtems/bspIo.h>
-#include <rtems/libio.h>
-#include <termios.h>
-#include <bsp/mbx.h>
-
-static void _BSP_output_char( char c );
-
-static void _BSP_null_char( char c ) {return;}
-static void serial_putchar(const char c);
-
-BSP_output_char_function_type     BSP_output_char = _BSP_null_char;
-BSP_polling_getchar_function_type BSP_poll_char = NULL;
-
-extern volatile m8xx_t m8xx;
-extern struct rtems_termios_tty *ttyp[];
-
-#if UARTS_IO_MODE == 2 || NVRAM_CONFIGURE == 1
-/*
- * _EPPCBug_pollRead
- *
- *  Read a character from the EPPCBug console, and return it. Return -1
- *  if there is no character in the input FIFO.
- *
- *  Input parameters:
- *    minor - selected channel
- *
- *  Output parameters:  NONE
- *
- *  Return value: char returned as positive signed int
- *                -1 if no character is present in the input FIFO.
- */
-static int _EPPCBug_pollRead(
-  int minor
-)
-{
-  char c;
-  volatile int simask;		/* We must read and write m8xx.simask */
-  int retval;
-  ISR_Level level;
-
-  struct {
-    int clun;
-    int dlun;
-    char * inbuf;
-    int nbytes_requested;
-    int reserved;
-  } volatile input_params;
-
-  struct {
-    int status;
-    union {
-      struct {
-        int input_char_available;
-        int output_possible;
-        int break_detected;
-        int modem_status;
-      } stat;
-      struct {
-        int nbytes_received;
-      } read;
-    } u;
-  } volatile output_params;
-
-  retval = -1;
-
-  input_params.clun = 0;
-
-  switch( minor ) {
-    case SMC1_MINOR:
-      input_params.dlun = 0;  /* Should be 4, but doesn't work with EPPCBug 1.1 */
-      break;
-    case SMC2_MINOR:
-      input_params.dlun = 5;
-      break;
-    case SCC2_MINOR:
-      input_params.dlun = 1;
-      break;
-#ifdef mpc860
-    case SCC3_MINOR:
-      input_params.dlun = 2;
-      break;
-    case SCC4_MINOR:
-      input_params.dlun = 3;
-      break;
-#endif
-    default:
-      input_params.dlun = 0;
-      break;
-  }
-
-  _ISR_Disable( level );
-  simask = m8xx.simask;
-
-  /* Check for a char in the input FIFO using .CIO_STAT */
-  __asm__ volatile( "li 10,0x202\n\
-                 mr 3, %0\n\
-                 mr 4, %1\n\
-                 sc"
-    :: "g" (&input_params), "g" (&output_params) : "3", "4", "10" );
-
-  if ( (output_params.status == 0) && output_params.u.stat.input_char_available) {
-
-    /* Read the char and return it */
-    input_params.inbuf = &c;
-    input_params.nbytes_requested = 1;
-
-    __asm__ volatile( "li     10,0x200     /* Code for .CIO_READ */\n\
-                   mr    3, %0         /* Address of input_params */\n\
-                   mr    4, %1         /* Address of output_params */\n\
-                   sc"             /* Call EPPCBUG */
-      :: "g" (&input_params), "g" (&output_params) : "3", "4", "10" );
-
-    if ( (output_params.status == 0) && output_params.u.read.nbytes_received)
-      retval = (int)c;
-  }
-
-  m8xx.simask = simask;
-  _ISR_Enable( level );
-  return retval;
-}
-#endif /* UARTS_IO_MODE == 2 || NVRAM_CONFIGURE == 1 */
-
-#if PRINTK_IO_MODE == 2 || UARTS_IO_MODE == 2 || NVRAM_CONFIGURE == 1
-/*
- * _EPPCBug_pollWrite
- *
- *  Output buffer through EPPCBug. Returns only once every character has been
- *  sent (polled output).
- *
- *  Input parameters:
- *    minor - selected channel
- *    buf - output buffer
- *    len - number of chars to output
- *
- *  Output parameters:  NONE
- *
- *  Return value: IGNORED
- */
-static ssize_t _EPPCBug_pollWrite(
-  int minor,
-  const char *buf,
-  size_t len
-)
-{
-  volatile int simask;
-  int i;
-  ISR_Level level;
-
-  struct {
-    int clun;
-    int dlun;
-    const char * outbuf;
-    int nbytes_to_output;
-    int reserved;
-  } volatile input_params;
-
-  struct {
-    int status;
-    union {
-      struct {
-        int input_char_available;
-        int output_possible;
-        int break_detected;
-        int modem_status;
-      } stat;
-      struct {
-        int nbytes_sent;
-      } write;
-    } u;
-  } volatile output_params;
-
-  input_params.clun = 0;
-  input_params.reserved = 0;
-
-  switch( minor ) {
-    case SMC1_MINOR:
-      input_params.dlun = 0;  /* Should be 4, but doesn't work with EPPCBug 1.1 */
-      break;
-    case SMC2_MINOR:
-      input_params.dlun = 5;
-      break;
-    case SCC2_MINOR:
-      input_params.dlun = 1;
-      break;
-#ifdef mpc860
-    case SCC3_MINOR:
-      input_params.dlun = 2;
-      break;
-    case SCC4_MINOR:
-      input_params.dlun = 3;
-      break;
-#endif
-    default:
-      input_params.dlun = 0;
-      break;
-  }
-
-  i = 0;
-
-  _ISR_Disable( level );
-  simask = m8xx.simask;
-
-  while (i < len) {
-    /* Wait for space in the output buffer */
-    do {
-      /* Check for space in the output FIFO */
-      __asm__ volatile( "li 10,0x202        /* Code for .CIO_STAT */\n\
-                     mr 3, %0           /* Address of input_params */\n\
-                     mr 4, %1           /* Address of output_params */\n\
-                     sc"            /* Call EPPCBUG */
-        :: "g" (&input_params), "g" (&output_params) : "3", "4", "10" );
-
-      if (output_params.status)
-        goto error;
-    } while (!output_params.u.stat.output_possible);
-
-    /* Output the characters until done */
-    input_params.outbuf = &buf[i];
-    input_params.nbytes_to_output = len - i;
-
-    __asm__ volatile( "li 10,0x201          /* Code for .CIO_WRITE */\n\
-                   mr 3, %0             /* Address of input_params */\n\
-                   mr 4, %1             /* Address of output_params */\n\
-                   sc"                  /* Call EPPCBUG */
-      :: "g" (&input_params), "g" (&output_params) : "3", "4", "10" );
-
-    if (output_params.status)
-      goto error;
-
-    i += output_params.u.write.nbytes_sent;
-  }
-
-  /* Return something */
-  m8xx.simask = simask;
-  _ISR_Enable( level );
-  return len;
-
-error:
-  m8xx.simask = simask;
-  _ISR_Enable( level );
-  return -1;
-}
-#endif /* PRINTK_IO_MODE == 2 || UARTS_IO_MODE == 2 || NVRAM_CONFIGURE == 1 */
-
-#if UARTS_USE_TERMIOS != 1 || NVRAM_CONFIGURE == 1
-/*
- *  do_poll_read
- *
- *  Input characters through polled I/O. Returns has soon as a character has
- *  been received. Otherwise, if we wait for the number of requested characters,
- *  we could be here forever!
- *
- *  CR is converted to LF on input. The terminal should not send a CR/LF pair
- *  when the return or enter key is pressed.
- *
- *  Input parameters:
- *    major - ignored. Should be the major number for this driver.
- *    minor - selected channel.
- *    arg->buffer - where to put the received characters.
- *    arg->count  - number of characters to receive before returning--Ignored.
- *
- *  Output parameters:
- *    arg->bytes_moved - the number of characters read. Always 1.
- *
- *  Return value: RTEMS_SUCCESSFUL
- *
- *  CANNOT BE COMBINED WITH INTERRUPT DRIVEN I/O!
- */
-static rtems_status_code do_poll_read(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void                    * arg
-)
-{
-  rtems_libio_rw_args_t *rw_args = arg;
-  int c;
-
-#if NVRAM_CONFIGURE == 1
-
-  int (*pollRead)( int minor );
-
-  if ( (nvram->console_mode & 0x06) == 0x04 )
-    pollRead = _EPPCBug_pollRead;
-  else
-    pollRead = m8xx_uart_pollRead;
-
-  while( (c = (*pollRead)(minor)) == -1 );
-  rw_args->buffer[0] = (uint8_t)c;
-  if( rw_args->buffer[0] == '\r' )
-      rw_args->buffer[0] = '\n';
-  rw_args->bytes_moved = 1;
-  return RTEMS_SUCCESSFUL;
-
-#else
-
-#if UARTS_IO_MODE == 2
-#define BSP_READ  _EPPCBug_pollRead
-#else
-#define BSP_READ  m8xx_uart_pollRead
-#endif
-
-  while( (c = BSP_READ(minor)) == -1 );
-  rw_args->buffer[0] = (uint8_t)c;
-  if( rw_args->buffer[0] == '\r' )
-      rw_args->buffer[0] = '\n';
-  rw_args->bytes_moved = 1;
-  return RTEMS_SUCCESSFUL;
-
-#endif
-}
-
-/*
- *  do_poll_write
- *
- *  Output characters through polled I/O. Returns only once every character has
- *  been sent.
- *
- *  CR is transmitted AFTER a LF on output.
- *
- *  Input parameters:
- *    major - ignored. Should be the major number for this driver.
- *    minor - selected channel
- *    arg->buffer - where to get the characters to transmit.
- *    arg->count  - the number of characters to transmit before returning.
- *
- *  Output parameters:
- *    arg->bytes_moved - the number of characters read
- *
- *  Return value: RTEMS_SUCCESSFUL
- *
- *  CANNOT BE COMBINED WITH INTERRUPT DRIVEN I/O!
- */
-static rtems_status_code do_poll_write(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void                    * arg
-)
-{
-  rtems_libio_rw_args_t *rw_args = arg;
-  uint32_t   i;
-  char cr ='\r';
-
-#if NVRAM_CONFIGURE == 1
-
-  ssize_t (*pollWrite)(int minor, const char *buf, size_t len);
-
-  if ( (nvram->console_mode & 0x06) == 0x04 )
-    pollWrite = _EPPCBug_pollWrite;
-  else
-    pollWrite = m8xx_uart_pollWrite;
-
-  for( i = 0; i < rw_args->count; i++ ) {
-    (*pollWrite)(minor, &(rw_args->buffer[i]), 1);
-    if ( rw_args->buffer[i] == '\n' )
-      (*pollWrite)(minor, &cr, 1);
-  }
-  rw_args->bytes_moved = i;
-  return RTEMS_SUCCESSFUL;
-
-#else
-
-#if UARTS_IO_MODE == 2
-#define BSP_WRITE _EPPCBug_pollWrite
-#else
-#define BSP_WRITE m8xx_uart_pollWrite
-#endif
-
-  for( i = 0; i < rw_args->count; i++ ) {
-    BSP_WRITE(minor, &(rw_args->buffer[i]), 1);
-    if ( rw_args->buffer[i] == '\n' )
-      BSP_WRITE(minor, &cr, 1);
-  }
-  rw_args->bytes_moved = i;
-  return RTEMS_SUCCESSFUL;
-
-#endif
-}
-#endif /* UARTS_USE_TERMIOS != 1 || NVRAM_CONFIGURE == 1 */
-
-/*
- *  Print functions prototyped in bspIo.h
- */
-
-static void _BSP_output_char( char c )
-{
-  char cr = '\r';
-
-  /*
-   *  Can't rely on console_initialize having been called before this function
-   *  is used, so it may fail unless output is done through EPPC-Bug.
-   */
-#if NVRAM_CONFIGURE == 1
-
-  rtems_device_minor_number printk_minor;
-
-  /* Use NVRAM info for configuration */
-  printk_minor = (nvram->console_printk_port & 0x70) >> 4;
-  if( (nvram->console_mode & 0x30) == 0x20 ) {
-    _EPPCBug_pollWrite( printk_minor, &c, 1 );
-    if( c == '\n' )
-      _EPPCBug_pollWrite( printk_minor, &cr, 1 );
-  }
-  else {
-    m8xx_uart_pollWrite( printk_minor, &c, 1 );
-    if( c == '\n' )
-      m8xx_uart_pollWrite( PRINTK_MINOR, &cr, 1 );
-	}
-
-#else
-
-#if PRINTK_IO_MODE == 2
-#define PRINTK_WRITE _EPPCBug_pollWrite
-#else
-#define PRINTK_WRITE m8xx_uart_pollWrite
-#endif
-
-  PRINTK_WRITE( PRINTK_MINOR, &c, 1 );
-  if( c == '\n' )
-    PRINTK_WRITE( PRINTK_MINOR, &cr, 1 );
-
-#endif
-}
-
-bd_t *eppcbugInfo= (bd_t *)0xdeadbeef;
-bd_t fakeEppcBugInfo = {
-  	0x42444944,		/* Should be 0x42444944 "BDID" */
-	sizeof(bd_t),		/* Size of this structure */
-	0,			/* revision of this structure */
-	0,			/* EPPCbug date, i.e. 0x11061997 */
-	0,			/* Memory start address */
-	0x1000000,		/* Memory (end) size in bytes */
-	0x28,			/* Internal Freq, in Hz */
-	0,			/* Bus Freq, in Hz */
-	0,			/* Boot device controller */
-	0			/* Boot device logical dev */
-};
-
-#define EARLY_CONSOLE
-#ifdef EARLY_CONSOLE
-
-#define MBX_CSR1	((volatile unsigned char *)0xfa100000)
-#define CSR1_COMEN	(unsigned char)0x02
-#define PROFF_CONS	PROFF_SMC1
-#define CPM_CR_CH_CONS	CPM_CR_CH_SMC1
-#define SMC_INDEX	0
-
-#include <bsp/commproc.h>
-
-static cpm8xx_t	*cpmp = (cpm8xx_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
-
-void
-serial_init(void)
-{
-	volatile smc_t		*sp;
-	volatile smc_uart_t	*up;
-	volatile cbd_t	*tbdf,  *rbdf;
-	volatile cpm8xx_t	*cp;
-	unsigned int		dpaddr, memaddr;
-	bd_t	*bd;
-
-#if NVRAM_CONFIGURE == 1
-	if ( ((nvram->console_mode & 0x06) != 0x04 ) ||
-	     ((nvram->console_mode & 0x30) != 0x20 )) {
-	  /*
-	   * FIXME: refine this condition...
-	   */
-#endif
-	bd = eppcbugInfo;
-
-	cp = cpmp;
-	sp = (smc_t*)&(cp->cp_smc[SMC_INDEX]);
-	up = (smc_uart_t *)&cp->cp_dparam[PROFF_CONS];
-
-	/* Disable transmitter/receiver.
-	*/
-	sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-
-	if (*MBX_CSR1 & CSR1_COMEN) {
-		/* COM1 is enabled.  Initialize SMC1 and use it for
-		 * the console port.
-		 */
-
-		/* Enable SDMA.
-		*/
-		((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sdcr = 1;
-
-		/* Use Port B for SMCs instead of other functions.
-		*/
-		cp->cp_pbpar |= 0x00000cc0;
-		cp->cp_pbdir &= ~0x00000cc0;
-		cp->cp_pbodr &= ~0x00000cc0;
-
-		/* Allocate space for two buffer descriptors in the DP ram.
-		 * For now, this address seems OK, but it may have to
-		 * change with newer versions of the firmware.
-		 */
-		dpaddr = 0x0800;
-
-		/* Grab a few bytes from the top of memory.  EPPC-Bug isn't
-		 * running any more, so we can do this.
-		 */
-		memaddr = (bd->bi_memsize - 32) & ~15;
-
-		/* Set the physical address of the host memory buffers in
-		 * the buffer descriptors.
-		 */
-		rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
-		rbdf->cbd_bufaddr = memaddr;
-		rbdf->cbd_sc = 0;
-		tbdf = rbdf + 1;
-		tbdf->cbd_bufaddr = memaddr+4;
-		tbdf->cbd_sc = 0;
-
-		/* Set up the uart parameters in the parameter ram.
-		*/
-		up->smc_rbase = dpaddr;
-		up->smc_tbase = dpaddr+sizeof(cbd_t);
-		up->smc_rfcr = SMC_EB;
-		up->smc_tfcr = SMC_EB;
-
-		/* Set UART mode, 8 bit, no parity, one stop.
-		 * Enable receive and transmit.
-		 */
-		sp->smc_smcmr = smcr_mk_clen(9) |  SMCMR_SM_UART;
-
-		/* Mask all interrupts and remove anything pending.
-		*/
-		sp->smc_smcm = 0;
-		sp->smc_smce = 0xff;
-
-		/* Set up the baud rate generator.
-		 * See 8xx_io/commproc.c for details.
-		 */
-		cp->cp_simode = 0x10000000;
-		cp->cp_brgc1 =
-			((((bd->bi_intfreq * 1000000)/16) / 9600) << 1) | CPM_BRG_EN;
-
-		/* Enable SMC1 for console output.
-		*/
-		*MBX_CSR1 &= ~CSR1_COMEN;
-	}
-	else {
-		/* SMCx is used as console port.
-		*/
-		tbdf = (cbd_t *)&cp->cp_dpmem[up->smc_tbase];
-		rbdf = (cbd_t *)&cp->cp_dpmem[up->smc_rbase];
-
-		/* Issue a stop transmit, and wait for it.
-		*/
-		cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_CONS,
-					CPM_CR_STOP_TX) | CPM_CR_FLG;
-		while (cp->cp_cpcr & CPM_CR_FLG);
-	}
-
-	/* Make the first buffer the only buffer.
-	*/
-	tbdf->cbd_sc |= BD_SC_WRAP;
-	rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
-	/* Single character receive.
-	*/
-	up->smc_mrblr = 1;
-	up->smc_maxidl = 0;
-
-	/* Initialize Tx/Rx parameters.
-	*/
-	cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_CONS, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-	while (cp->cp_cpcr & CPM_CR_FLG);
-
-	/* Enable transmitter/receiver.
-	*/
-	sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
-#if NVRAM_CONFIGURE == 1
-	}
-	else {
-	  const char bootmsg_text[]= "using EPPC bug for console I/O\n";
-	  _EPPCBug_pollWrite((nvram->console_printk_port & 0x70) >> 4,
-			     bootmsg_text,
-			     sizeof(bootmsg_text)-1);
-	}
-#endif
-#if NVRAM_CONFIGURE == 1
-	if ((nvram->console_mode & 0x30) == 0x20 ) {
-	  BSP_output_char = _BSP_output_char;
-	}
-	else {
-	  BSP_output_char = serial_putchar;
-	}
-#else
-
-	BSP_output_char = serial_putchar;
-#endif
-}
-
-void
-serial_putchar(const char c)
-{
-	volatile cbd_t		*tbdf;
-	volatile char		*buf;
-	volatile smc_uart_t	*up;
-
-	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
-	tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase];
-
-	/* Wait for last character to go.
-	*/
-	buf = (char *)tbdf->cbd_bufaddr;
-	while (tbdf->cbd_sc & BD_SC_READY);
-
-	*buf = c;
-	tbdf->cbd_datlen = 1;
-	tbdf->cbd_sc |= BD_SC_READY;
-}
-
-char
-serial_getc(void)
-{
-	volatile cbd_t		*rbdf;
-	volatile char		*buf;
-	volatile smc_uart_t	*up;
-	char			c;
-
-	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
-	rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
-	/* Wait for character to show up.
-	*/
-	buf = (char *)rbdf->cbd_bufaddr;
-	while (rbdf->cbd_sc & BD_SC_EMPTY);
-	c = *buf;
-	rbdf->cbd_sc |= BD_SC_EMPTY;
-
-	return(c);
-}
-
-int
-serial_tstc(void)
-{
-	volatile cbd_t		*rbdf;
-	volatile smc_uart_t	*up;
-
-	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
-	rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
-	return(!(rbdf->cbd_sc & BD_SC_EMPTY));
-}
-
-#endif
-/*
- ***************
- * BOILERPLATE *
- ***************
- *
- *  All these functions are prototyped in rtems/c/src/lib/include/console.h.
- */
-
-/*
- * Initialize and register the device
- */
-rtems_device_driver console_initialize(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void *arg
-)
-{
-  rtems_status_code status;
-  rtems_device_minor_number console_minor;
-
-  /*
-   * Set up TERMIOS if needed
-   */
-#if NVRAM_CONFIGURE == 1
-  /* Use NVRAM info for configuration */
-  console_minor = nvram->console_printk_port & 0x07;
-
-  if ( nvram->console_mode & 0x01 )
-    /* termios */
-    rtems_termios_initialize ();
-
-  /*
-   *  Do common initialization.
-   */
-  m8xx_uart_initialize();
-
-  /*
-   * Do device-specific initialization
-   */
-  if ( !nvram->eppcbug_smc1 &&
-    ( ((nvram->console_mode & 0x30) != 0x20) ||
-     (((nvram->console_printk_port & 0x30) >> 4) != SMC1_MINOR) ) )
-    m8xx_uart_smc_initialize(SMC1_MINOR); /* /dev/tty0 */
-
-  if ( ((nvram->console_mode & 0x30) != 0x20) ||
-      (((nvram->console_printk_port & 0x30) >> 4) != SMC2_MINOR) )
-    m8xx_uart_smc_initialize(SMC2_MINOR); /* /dev/tty1 */
-
-  if ( ((nvram->console_mode & 0x30) != 0x20) ||
-      (((nvram->console_printk_port & 0x30) >> 4) != SCC2_MINOR) )
-    m8xx_uart_scc_initialize(SCC2_MINOR); /* /dev/tty2    */
-
-#ifdef mpc860
-
-  if ( ((nvram->console_mode & 0x30) != 0x20) ||
-      (((nvram->console_printk_port & 0x30) >> 4) != SCC3_MINOR) )
-    m8xx_uart_scc_initialize(SCC3_MINOR); /* /dev/tty3    */
-
-  if ( ((nvram->console_mode & 0x30) != 0x20) ||
-      (((nvram->console_printk_port & 0x30) >> 4) != SCC4_MINOR) )
-    m8xx_uart_scc_initialize(SCC4_MINOR); /* /dev/tty4    */
-
-#endif /* mpc860 */
-  BSP_output_char = _BSP_output_char;
-#else /* NVRAM_CONFIGURE != 1 */
-
-    console_minor = CONSOLE_MINOR;
-
-#if UARTS_USE_TERMIOS == 1
-
-    rtems_termios_initialize ();
-
-#endif /* UARTS_USE_TERMIOS */
-
-  /*
-   *  Do common initialization.
-   */
-  m8xx_uart_initialize();
-
-  /*
-   * Do device-specific initialization
-   */
-#if !defined(EPPCBUG_SMC1) && ( PRINTK_IO_MODE != 2 || PRINTK_MINOR != SMC1_MINOR )
-  m8xx_uart_smc_initialize(SMC1_MINOR); /* /dev/tty0 */
-#endif
-
-#if PRINTK_IO_MODE != 2 || PRINTK_MINOR != SMC2_MINOR
-  m8xx_uart_smc_initialize(SMC2_MINOR); /* /dev/tty1 */
-#endif
-
-  #if PRINTK_IO_MODE != 2 || PRINTK_MINOR != SCC2_MINOR
-  m8xx_uart_scc_initialize(SCC2_MINOR); /* /dev/tty2    */
-   #endif
-
-#ifdef mpc860
-
-#if PRINTK_IO_MODE != 2 || PRINTK_MINOR != SCC3_MINOR
-  m8xx_uart_scc_initialize(SCC3_MINOR); /* /dev/tty3    */
-#endif
-
-#if PRINTK_IO_MODE != 2 || PRINTK_MINOR != SCC4_MINOR
-  m8xx_uart_scc_initialize(SCC4_MINOR); /* /dev/tty4    */
-#endif
-
-#endif /* mpc860 */
-
-  BSP_output_char = _BSP_output_char;
-
-#endif /* NVRAM_CONFIGURE != 1 */
-
-  status = rtems_io_register_name ("/dev/tty0", major, SMC1_MINOR);
-  if (status != RTEMS_SUCCESSFUL)
-    rtems_fatal_error_occurred (status);
-
-  status = rtems_io_register_name ("/dev/tty1", major, SMC2_MINOR);
-  if (status != RTEMS_SUCCESSFUL)
-    rtems_fatal_error_occurred (status);
-
-  status = rtems_io_register_name ("/dev/tty2", major, SCC2_MINOR);
-  if (status != RTEMS_SUCCESSFUL)
-    rtems_fatal_error_occurred (status);
-
-#ifdef mpc860
-  status = rtems_io_register_name ("/dev/tty3", major, SCC3_MINOR);
-  if (status != RTEMS_SUCCESSFUL)
-    rtems_fatal_error_occurred (status);
-
-  status = rtems_io_register_name ("/dev/tty4", major, SCC4_MINOR);
-  if (status != RTEMS_SUCCESSFUL)
-    rtems_fatal_error_occurred (status);
-
-#endif /* mpc860 */
-
-  /* Now register the RTEMS console */
-  status = rtems_io_register_name ("/dev/console", major, console_minor);
-  if (status != RTEMS_SUCCESSFUL)
-    rtems_fatal_error_occurred (status);
-
-  return RTEMS_SUCCESSFUL;
-}
-
-/*
- * Open the device
- */
-rtems_device_driver console_open(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void *arg
-)
-{
-#if NVRAM_CONFIGURE == 1
-  /* Used to track termios private data for callbacks */
-  rtems_libio_open_close_args_t *args = arg;
-  static const rtems_termios_callbacks sccEPPCBugCallbacks = {
-    NULL,                       	/* firstOpen */
-    NULL,                       	/* lastClose */
-    _EPPCBug_pollRead,          	/* pollRead */
-    _EPPCBug_pollWrite,         	/* write */
-    NULL,                       	/* stopRemoteTx */
-    NULL,                       	/* startRemoteTx */
-    0                           	/* outputUsesInterrupts */
-  };
-#endif
-  static const rtems_termios_callbacks pollCallbacks = {
-    NULL,                       	/* firstOpen */
-    NULL,                       	/* lastClose */
-    m8xx_uart_pollRead,        	        /* pollRead */
-    m8xx_uart_pollWrite,       	        /* write */
-    m8xx_uart_setAttributes,            /* setAttributes */
-    NULL,                       	/* stopRemoteTx */
-    NULL,                       	/* startRemoteTx */
-    0                           	/* outputUsesInterrupts */
-  };
-  rtems_status_code sc;
-
-#if (NVRAM_CONFIGURE == 1) || \
-    ((NVRAM_CONFIGURE != 1) && (UARTS_USE_TERMIOS == 1) && \
-      (UARTS_IO_MODE == 1))
-
-  static const rtems_termios_callbacks intrCallbacks = {
-    NULL,                       	/* firstOpen */
-    NULL,                       	/* lastClose */
-    NULL,                               /* pollRead */
-    m8xx_uart_write,       	        /* write */
-    m8xx_uart_setAttributes,    	/* setAttributes */
-    NULL,                       	/* stopRemoteTx */
-    NULL,                       	/* startRemoteTx */
-    1                           	/* outputUsesInterrupts */
-  };
-#endif
-
-  if ( minor > NUM_PORTS-1 )
-    return RTEMS_INVALID_NUMBER;
-
-#if NVRAM_CONFIGURE == 1
-
-  /* Use NVRAM info for configuration */
-  if ( nvram->console_mode & 0x01 ) {
-    /* Use termios */
-    if ( (nvram->console_mode & 0x06) == 0x02 ) {
-      /* interrupt-driven I/O */
-      sc = rtems_termios_open( major, minor, arg, &intrCallbacks );
-      ttyp[minor] = args->iop->data1;        /* Keep cookie returned by termios_open */
-      return sc;
-    }
-    else if ( (nvram->console_mode & 0x06) == 0x04 )
-      /* polled I/O through EPPC-Bug, better be through SMC1 */
-      return rtems_termios_open( major, minor, arg, &sccEPPCBugCallbacks );
-    else
-      /* normal polled I/O */
-      return rtems_termios_open( major, minor, arg, &pollCallbacks );
-  }
-  else
-    /* no termios -- default to polled I/O */
-    return RTEMS_SUCCESSFUL;
-
-#else /* NVRAM_CONFIGURE != 1 */
-
-#if UARTS_USE_TERMIOS == 1
-
-#if UARTS_IO_MODE == 2    /* EPPCBug polled I/O with termios */
-  sc = rtems_termios_open( major, minor, arg, &sccEPPCBugCallbacks );
-#elif UARTS_IO_MODE == 1  /* RTEMS interrupt-driven I/O with termios */
-  sc = rtems_termios_open( major, minor, arg, &intrCallbacks );
-  ttyp[minor] = args->iop->data1;        /* Keep cookie returned by termios_open */
-#else                     /* RTEMS polled I/O with termios */
-  sc = rtems_termios_open( major, minor, arg, &pollCallbacks );
-#endif
-
-#else /* UARTS_USE_TERMIOS != 1 */
-  /* no termios -- default to polled I/O */
-  sc = RTEMS_SUCCESSFUL;
-#endif /* UARTS_USE_TERMIOS != 1 */
-
-  return sc;
-
-#endif /* NVRAM_CONFIGURE != 1 */
-}
-
-/*
- * Close the device
- */
-rtems_device_driver console_close(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void *arg
-)
-{
-  if ( minor > NUM_PORTS-1 )
-    return RTEMS_INVALID_NUMBER;
-
-#if NVRAM_CONFIGURE == 1
-
-  /* Use NVRAM info for configuration */
-  if ( nvram->console_mode & 0x01 )
-    /* use termios */
-    return rtems_termios_close( arg );
-  else
-    /* no termios */
-    return RTEMS_SUCCESSFUL;
-
-#else /* NVRAM_CONFIGURE != 1 */
-
-#if UARTS_USE_TERMIOS == 1
-  return rtems_termios_close( arg );
-#else
-  return RTEMS_SUCCESSFUL;
-#endif
-
-#endif /* NVRAM_CONFIGURE != 1 */
-}
-
-/*
- * Read from the device
- */
-rtems_device_driver console_read(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void *arg
-)
-{
-  if ( minor > NUM_PORTS-1 )
-    return RTEMS_INVALID_NUMBER;
-
-#if NVRAM_CONFIGURE == 1
-
-  /* Use NVRAM info for configuration */
-  if ( nvram->console_mode & 0x01 )
-    /* use termios */
-    return rtems_termios_read( arg );
-  else
-    /* no termios -- default to polled */
-    return do_poll_read( major, minor, arg );
-
-#else
-
-#if UARTS_USE_TERMIOS == 1
-  return rtems_termios_read( arg );
-#else
-  return do_poll_read( major, minor, arg );
-#endif
-
-#endif
-}
-
-/*
- * Write to the device
- */
-rtems_device_driver console_write(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void *arg
-)
-{
-  if ( minor > NUM_PORTS-1 )
-    return RTEMS_INVALID_NUMBER;
-
-#if NVRAM_CONFIGURE == 1
-
-  /* Use NVRAM info for configuration */
-  if ( nvram->console_mode & 0x01 )
-    /* use termios */
-    return rtems_termios_write( arg );
-  else
-    /* no termios -- default to polled */
-    return do_poll_write( major, minor, arg );
-
-#else
-
-#if UARTS_USE_TERMIOS == 1
-  return rtems_termios_write( arg );
-#else
-    /* no termios -- default to polled */
-  return do_poll_write( major, minor, arg );
-#endif
-
-#endif
-}
-
-/*
- * Handle ioctl request.
- */
-rtems_device_driver console_control(
-  rtems_device_major_number major,
-  rtems_device_minor_number minor,
-  void *arg
-)
-{
-  if ( minor > NUM_PORTS-1 )
-    return RTEMS_INVALID_NUMBER;
-
-#if NVRAM_CONFIGURE == 1
-
-  /* Uuse NVRAM info for configuration */
-  if ( nvram->console_mode & 0x01 )
-    /* termios */
-    return rtems_termios_ioctl( arg );
-  else
-    /* no termios -- default to polled */
-    return RTEMS_SUCCESSFUL;
-
-#else
-
-#if UARTS_USE_TERMIOS == 1
-  return rtems_termios_ioctl( arg );
-#else
-  return RTEMS_SUCCESSFUL;
-#endif
-
-#endif
-}
-
-/*
- *  Support routine for console-generic
- */
-
-int mbx8xx_console_get_configuration(void)
-{
-#if NVRAM_CONFIGURE == 1
-  return nvram->console_mode;
-#else
-#if UARTS_IO_MODE == 1
-  return 0x02;
-#else
-  return 0;
-#endif
-#endif
-
-}