File removed as it was not being used.

1 files changed, 0 insertions, 268 deletions

diff --git a/c/src/lib/libbsp/i386/i386ex/network/dma.h b/c/src/lib/libbsp/i386/i386ex/network/dma.h
deleted file mode 100644
index 51c0d0c98a..0000000000
--- a/c/src/lib/libbsp/i386/i386ex/network/dma.h
+++ /dev/null
@@ -1,268 +0,0 @@
-/* $Id$
- * linux/include/asm/dma.h: Defines for using and allocating dma channels.
- * Written by Hennus Bergman, 1992.
- * High DMA channel support & info by Hannu Savolainen
- * and John Boyd, Nov. 1992.
- */
-
-#ifndef _ASM_DMA_H
-#define _ASM_DMA_H
-
-
-
-#define dma_outb(x,y)	outport_byte(y,x)
-
-#define dma_inb		inport_byte
-
-/*
- * NOTES about DMA transfers:
- *
- *  controller 1: channels 0-3, byte operations, ports 00-1F
- *  controller 2: channels 4-7, word operations, ports C0-DF
- *
- *  - ALL registers are 8 bits only, regardless of transfer size
- *  - channel 4 is not used - cascades 1 into 2.
- *  - channels 0-3 are byte - addresses/counts are for physical bytes
- *  - channels 5-7 are word - addresses/counts are for physical words
- *  - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
- *  - transfer count loaded to registers is 1 less than actual count
- *  - controller 2 offsets are all even (2x offsets for controller 1)
- *  - page registers for 5-7 don't use data bit 0, represent 128K pages
- *  - page registers for 0-3 use bit 0, represent 64K pages
- *
- * DMA transfers are limited to the lower 16MB of _physical_ memory.  
- * Note that addresses loaded into registers must be _physical_ addresses,
- * not logical addresses (which may differ if paging is active).
- *
- *  Address mapping for channels 0-3:
- *
- *   A23 ... A16 A15 ... A8  A7 ... A0    (Physical addresses)
- *    |  ...  |   |  ... |   |  ... |
- *    |  ...  |   |  ... |   |  ... |
- *    |  ...  |   |  ... |   |  ... |
- *   P7  ...  P0  A7 ... A0  A7 ... A0   
- * |    Page    | Addr MSB | Addr LSB |   (DMA registers)
- *
- *  Address mapping for channels 5-7:
- *
- *   A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0    (Physical addresses)
- *    |  ...  |   \   \   ... \  \  \  ... \  \
- *    |  ...  |    \   \   ... \  \  \  ... \  (not used)
- *    |  ...  |     \   \   ... \  \  \  ... \
- *   P7  ...  P1 (0) A7 A6  ... A0 A7 A6 ... A0   
- * |      Page      |  Addr MSB   |  Addr LSB  |   (DMA registers)
- *
- * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
- * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
- * the hardware level, so odd-byte transfers aren't possible).
- *
- * Transfer count (_not # bytes_) is limited to 64K, represented as actual
- * count - 1 : 64K => 0xFFFF, 1 => 0x0000.  Thus, count is always 1 or more,
- * and up to 128K bytes may be transferred on channels 5-7 in one operation. 
- *
- */
-
-#define MAX_DMA_CHANNELS	8
-
-/* The maximum address that we can perform a DMA transfer to on this platform */
-#define MAX_DMA_ADDRESS      0x1000000
-
-/* 8237 DMA controllers */
-#define IO_DMA1_BASE	0x00	/* 8 bit slave DMA, channels 0..3 */
-#define IO_DMA2_BASE	0xC0	/* 16 bit master DMA, ch 4(=slave input)..7 */
-
-/* DMA controller registers */
-#define DMA1_CMD_REG		0x08	/* command register (w) */
-#define DMA1_STAT_REG		0x08	/* status register (r) */
-#define DMA1_REQ_REG            0x09    /* request register (w) */
-#define DMA1_MASK_REG		0x0A	/* single-channel mask (w) */
-#define DMA1_MODE_REG		0x0B	/* mode register (w) */
-#define DMA1_CLEAR_FF_REG	0x0C	/* clear pointer flip-flop (w) */
-#define DMA1_TEMP_REG           0x0D    /* Temporary Register (r) */
-#define DMA1_RESET_REG		0x0D	/* Master Clear (w) */
-#define DMA1_CLR_MASK_REG       0x0E    /* Clear Mask */
-#define DMA1_MASK_ALL_REG       0x0F    /* all-channels mask (w) */
-
-#define DMA2_CMD_REG		0xD0	/* command register (w) */
-#define DMA2_STAT_REG		0xD0	/* status register (r) */
-#define DMA2_REQ_REG            0xD2    /* request register (w) */
-#define DMA2_MASK_REG		0xD4	/* single-channel mask (w) */
-#define DMA2_MODE_REG		0xD6	/* mode register (w) */
-#define DMA2_CLEAR_FF_REG	0xD8	/* clear pointer flip-flop (w) */
-#define DMA2_TEMP_REG           0xDA    /* Temporary Register (r) */
-#define DMA2_RESET_REG		0xDA	/* Master Clear (w) */
-#define DMA2_CLR_MASK_REG       0xDC    /* Clear Mask */
-#define DMA2_MASK_ALL_REG       0xDE    /* all-channels mask (w) */
-
-#define DMA_ADDR_0              0x00    /* DMA address registers */
-#define DMA_ADDR_1              0x02
-#define DMA_ADDR_2              0x04
-#define DMA_ADDR_3              0x06
-#define DMA_ADDR_4              0xC0
-#define DMA_ADDR_5              0xC4
-#define DMA_ADDR_6              0xC8
-#define DMA_ADDR_7              0xCC
-
-#define DMA_CNT_0               0x01    /* DMA count registers */
-#define DMA_CNT_1               0x03
-#define DMA_CNT_2               0x05
-#define DMA_CNT_3               0x07
-#define DMA_CNT_4               0xC2
-#define DMA_CNT_5               0xC6
-#define DMA_CNT_6               0xCA
-#define DMA_CNT_7               0xCE
-
-#define DMA_PAGE_0              0x87    /* DMA page registers */
-#define DMA_PAGE_1              0x83
-#define DMA_PAGE_2              0x81
-#define DMA_PAGE_3              0x82
-#define DMA_PAGE_5              0x8B
-#define DMA_PAGE_6              0x89
-#define DMA_PAGE_7              0x8A
-
-#define DMA_MODE_READ	0x44	/* I/O to memory, no autoinit, increment, single mode */
-#define DMA_MODE_WRITE	0x48	/* memory to I/O, no autoinit, increment, single mode */
-#define DMA_MODE_CASCADE 0xC0   /* pass thru DREQ->HRQ, DACK<-HLDA only */
-
-/* enable/disable a specific DMA channel */
-static __inline__ void enable_dma(unsigned int dmanr)
-{
-	if (dmanr<=3)
-	  {dma_outb(dmanr,  DMA1_MASK_REG);}
-	else
-	  {dma_outb(dmanr & 3,  DMA2_MASK_REG);}
-}
-
-static __inline__ void disable_dma(unsigned int dmanr)
-{
-	if (dmanr<=3)
-	  { dma_outb(dmanr | 4,  DMA1_MASK_REG); }
-	else
-	  { dma_outb((dmanr & 3) | 4,  DMA2_MASK_REG);}
-}
-
-/* Clear the 'DMA Pointer Flip Flop'.
- * Write 0 for LSB/MSB, 1 for MSB/LSB access.
- * Use this once to initialize the FF to a known state.
- * After that, keep track of it. :-)
- * --- In order to do that, the DMA routines below should ---
- * --- only be used while interrupts are disabled! ---
- */
-static __inline__ void clear_dma_ff(unsigned int dmanr)
-{
-	if (dmanr<=3)
-	  {dma_outb(0,  DMA1_CLEAR_FF_REG);}
-	else
-	  {dma_outb(0,  DMA2_CLEAR_FF_REG);}
-}
-
-/* set mode (above) for a specific DMA channel */
-static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
-{
-	if (dmanr<=3)
-	  { dma_outb(mode | dmanr,  DMA1_MODE_REG);}
-	else
-	  { dma_outb(mode | (dmanr&3),  DMA2_MODE_REG);}
-}
-
-/* Set only the page register bits of the transfer address.
- * This is used for successive transfers when we know the contents of
- * the lower 16 bits of the DMA current address register, but a 64k boundary
- * may have been crossed.
- */
-static __inline__ void set_dma_page(unsigned int dmanr, char pagenr)
-{
-	switch(dmanr) {
-		case 0:
-		  {dma_outb(pagenr, DMA_PAGE_0);}
-			break;
-		case 1:
-		  {dma_outb(pagenr, DMA_PAGE_1);}
-			break;
-		case 2:
-		  {dma_outb(pagenr, DMA_PAGE_2);}
-			break;
-		case 3:
-		  {dma_outb(pagenr, DMA_PAGE_3);}
-			break;
-		case 5:
-		  {dma_outb(pagenr & 0xfe, DMA_PAGE_5);}
-			break;
-		case 6:
-		  {dma_outb(pagenr & 0xfe, DMA_PAGE_6);}
-			break;
-		case 7:
-		  {dma_outb(pagenr & 0xfe, DMA_PAGE_7);}
-			break;
-	}
-}
-
-
-/* Set transfer address & page bits for specific DMA channel.
- * Assumes dma flipflop is clear.
- */
-static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
-{
-	set_dma_page(dmanr, a>>16);
-	if (dmanr <= 3)  {
-	    dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
-            dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
-	}  else  {
-	    dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
-	    dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
-	}
-}
-
-
-/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
- * a specific DMA channel.
- * You must ensure the parameters are valid.
- * NOTE: from a manual: "the number of transfers is one more
- * than the initial word count"! This is taken into account.
- * Assumes dma flip-flop is clear.
- * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
- */
-static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
-{
-        count--;
-	if (dmanr <= 3)  {
-	    dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
-	    dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
-        } else {
-	    dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
-	    dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
-        }
-}
-
-
-/* Get DMA residue count. After a DMA transfer, this
- * should return zero. Reading this while a DMA transfer is
- * still in progress will return unpredictable results.
- * If called before the channel has been used, it may return 1.
- * Otherwise, it returns the number of _bytes_ left to transfer.
- *
- * Assumes DMA flip-flop is clear.
- */
-static __inline__ int get_dma_residue(unsigned int dmanr)
-{
-	unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
-					 : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
-
-	/* using short to get 16-bit wrap around */
-	unsigned short count,temp;
-
-	dma_inb(io_port,count);
-	count ++; 
-	dma_inb(io_port,temp);
-	count += temp << 8;
-	
-	return (dmanr<=3)? count : (count<<1);
-}
-
-
-
-
-#endif /* _ASM_DMA_H */
-
-
-