blob: bfabe10605bfb3b25fab7c241607c086cbd81386 (
plain) (
tree)
|
|
/*
* This include file definitions related to an Intel i386ex board.
*
* COPYRIGHT (c) 1989-1999.
* On-Line Applications Research Corporation (OAR).
*
* The license and distribution terms for this file may be
* found in the file LICENSE in this distribution or at
* http://www.OARcorp.com/rtems/license.html.
*
* $Id$
*/
#ifndef __I386EX_BSP_h
#define __I386EX_BSP_h
#ifdef __cplusplus
extern "C" {
#endif
#include <bspopts.h>
#include <rtems.h>
#include <iosupp.h>
#include <console.h>
#include <clockdrv.h>
#include <rtems/bspIo.h>
#include <irq.h>
/*
* confdefs.h overrides for this BSP:
* - number of termios serial ports (defaults to 1)
* - Interrupt stack space is not minimum if defined.
*/
/* #define CONFIGURE_NUMBER_OF_TERMIOS_PORTS 2 */
#define CONFIGURE_INTERRUPT_STACK_MEMORY (8 * 1024)
/*
* Define the time limits for RTEMS Test Suite test durations.
* Long test and short test duration limits are provided. These
* values are in seconds and need to be converted to ticks for the
* application.
*
*/
#define MAX_LONG_TEST_DURATION 300 /* 5 minutes = 300 seconds */
#define MAX_SHORT_TEST_DURATION 3 /* 3 seconds */
/*
* Define the interrupt mechanism for Time Test 27
*
* NOTE: Use a software interrupt for the i386.
*/
#define MUST_WAIT_FOR_INTERRUTPT 0
#define Install_tm27_vector(handler) \
{ \
rtems_isr_entry dummy; \
rtems_interrupt_catch(handler, 0x90, &dummy); \
}
#define Cause_tm27_intr() asm volatile( "int $0x90" : : );
#define Clear_tm27_intr()
#define Lower_tm27_intr()
/*
* Simple spin delay in microsecond units for device drivers.
* This is very dependent on the clock speed of the target.
*/
#define rtems_bsp_delay( _microseconds ) \
{ \
rtems_unsigned32 _counter; \
\
_counter = (_microseconds); \
\
asm volatile ( "0: nop;" \
" mov %0,%0 ;" \
" loop 0b" : "=c" (_counter) \
: "0" (_counter) \
); \
\
}
/* Constants */
#define RAM_START 0
/* replaced the earlier EI kludge of 0xfffff */
#define RAM_END 0x100000
/* I/O addressing */
/*
*#define Is_tx_ready( _status ) ( (_status) & 0x20 )
*/
/* dec 20. try the TE instead of TBE as the check */
#define Is_tx_ready( _status ) ( (_status) & 0x40 )
#define Is_rx_ready( _status ) ( (_status) & 0x01 )
/* Structures */
#ifdef F386_INIT
#undef BSP_EXTERN
#define BSP_EXTERN
#else
#undef BSP_EXTERN
#define BSP_EXTERN extern
#endif
/*
* Device Driver Table Entries
*/
/*
* NOTE: Use the standard Console driver entry
*/
/*
* NOTE: Use the standard Clock driver entry
*/
/* miscellaneous stuff assumed to exist */
extern rtems_configuration_table BSP_Configuration;
#define IDT_SIZE 256
#define GDT_SIZE 8192
extern interrupt_gate_descriptor Interrupt_descriptor_table[IDT_SIZE];
extern segment_descriptors Global_descriptor_table [GDT_SIZE];
BSP_EXTERN unsigned short Idt[3]; /* Interrupt Descriptor Table Address */
BSP_EXTERN unsigned short Gdt[3]; /* Global Descriptor Table Address */
BSP_EXTERN unsigned int Idt_base;
BSP_EXTERN unsigned int Gdt_base;
/* routines */
#ifdef __cplusplus
}
#endif
#endif
/* end of include file */
|
