#include /*- * SPDX-License-Identifier: BSD-2-Clause-FreeBSD * * Copyright (c) 2013 Ian Lepore * Copyright (c) 2011 Ben Gray . * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * */ #include __FBSDID("$FreeBSD$"); #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include struct ti_sdhci_softc { device_t dev; struct sdhci_fdt_gpio * gpio; struct resource * mem_res; struct resource * irq_res; void * intr_cookie; struct sdhci_slot slot; clk_ident_t mmchs_clk_id; uint32_t mmchs_reg_off; uint32_t sdhci_reg_off; uint32_t baseclk_hz; uint32_t cmd_and_mode; uint32_t sdhci_clkdiv; boolean_t disable_highspeed; boolean_t force_card_present; boolean_t disable_readonly; }; /* * Table of supported FDT compat strings. * * Note that "ti,mmchs" is our own invention, and should be phased out in favor * of the documented names. * * Note that vendor Beaglebone dtsi files use "ti,omap3-hsmmc" for the am335x. */ static struct ofw_compat_data compat_data[] = { {"ti,omap3-hsmmc", 1}, {"ti,omap4-hsmmc", 1}, {"ti,mmchs", 1}, {NULL, 0}, }; /* * The MMCHS hardware has a few control and status registers at the beginning of * the device's memory map, followed by the standard sdhci register block. * Different SoCs have the register blocks at different offsets from the * beginning of the device. Define some constants to map out the registers we * access, and the various per-SoC offsets. The SDHCI_REG_OFFSET is how far * beyond the MMCHS block the SDHCI block is found; it's the same on all SoCs. */ #define OMAP3_MMCHS_REG_OFFSET 0x000 #define OMAP4_MMCHS_REG_OFFSET 0x100 #define AM335X_MMCHS_REG_OFFSET 0x100 #define SDHCI_REG_OFFSET 0x100 #define MMCHS_SYSCONFIG 0x010 #define MMCHS_SYSCONFIG_RESET (1 << 1) #define MMCHS_SYSSTATUS 0x014 #define MMCHS_SYSSTATUS_RESETDONE (1 << 0) #define MMCHS_CON 0x02C #define MMCHS_CON_DW8 (1 << 5) #define MMCHS_CON_DVAL_8_4MS (3 << 9) #define MMCHS_CON_OD (1 << 0) #define MMCHS_SYSCTL 0x12C #define MMCHS_SYSCTL_CLKD_MASK 0x3FF #define MMCHS_SYSCTL_CLKD_SHIFT 6 #define MMCHS_SD_CAPA 0x140 #define MMCHS_SD_CAPA_VS18 (1 << 26) #define MMCHS_SD_CAPA_VS30 (1 << 25) #define MMCHS_SD_CAPA_VS33 (1 << 24) /* Forward declarations, CAM-relataed */ // static void ti_sdhci_cam_poll(struct cam_sim *); // static void ti_sdhci_cam_action(struct cam_sim *, union ccb *); // static int ti_sdhci_cam_settran_settings(struct ti_sdhci_softc *sc, union ccb *); static inline uint32_t ti_mmchs_read_4(struct ti_sdhci_softc *sc, bus_size_t off) { return (bus_read_4(sc->mem_res, off + sc->mmchs_reg_off)); } static inline void ti_mmchs_write_4(struct ti_sdhci_softc *sc, bus_size_t off, uint32_t val) { bus_write_4(sc->mem_res, off + sc->mmchs_reg_off, val); } static inline uint32_t RD4(struct ti_sdhci_softc *sc, bus_size_t off) { return (bus_read_4(sc->mem_res, off + sc->sdhci_reg_off)); } static inline void WR4(struct ti_sdhci_softc *sc, bus_size_t off, uint32_t val) { bus_write_4(sc->mem_res, off + sc->sdhci_reg_off, val); } static uint8_t ti_sdhci_read_1(device_t dev, struct sdhci_slot *slot, bus_size_t off) { struct ti_sdhci_softc *sc = device_get_softc(dev); return ((RD4(sc, off & ~3) >> (off & 3) * 8) & 0xff); } static uint16_t ti_sdhci_read_2(device_t dev, struct sdhci_slot *slot, bus_size_t off) { struct ti_sdhci_softc *sc = device_get_softc(dev); uint32_t clkdiv, val32; /* * The MMCHS hardware has a non-standard interpretation of the sdclock * divisor bits. It uses the same bit positions as SDHCI 3.0 (15..6) * but doesn't split them into low:high fields. Instead they're a * single number in the range 0..1023 and the number is exactly the * clock divisor (with 0 and 1 both meaning divide by 1). The SDHCI * driver code expects a v2.0 or v3.0 divisor. The shifting and masking * here extracts the MMCHS representation from the hardware word, cleans * those bits out, applies the 2N adjustment, and plugs the result into * the bit positions for the 2.0 or 3.0 divisor in the returned register * value. The ti_sdhci_write_2() routine performs the opposite * transformation when the SDHCI driver writes to the register. */ if (off == SDHCI_CLOCK_CONTROL) { val32 = RD4(sc, SDHCI_CLOCK_CONTROL); clkdiv = ((val32 >> MMCHS_SYSCTL_CLKD_SHIFT) & MMCHS_SYSCTL_CLKD_MASK) / 2; val32 &= ~(MMCHS_SYSCTL_CLKD_MASK << MMCHS_SYSCTL_CLKD_SHIFT); val32 |= (clkdiv & SDHCI_DIVIDER_MASK) << SDHCI_DIVIDER_SHIFT; if (slot->version >= SDHCI_SPEC_300) val32 |= ((clkdiv >> SDHCI_DIVIDER_MASK_LEN) & SDHCI_DIVIDER_HI_MASK) << SDHCI_DIVIDER_HI_SHIFT; return (val32 & 0xffff); } /* * Standard 32-bit handling of command and transfer mode. */ if (off == SDHCI_TRANSFER_MODE) { return (sc->cmd_and_mode >> 16); } else if (off == SDHCI_COMMAND_FLAGS) { return (sc->cmd_and_mode & 0x0000ffff); } return ((RD4(sc, off & ~3) >> (off & 3) * 8) & 0xffff); } static uint32_t ti_sdhci_read_4(device_t dev, struct sdhci_slot *slot, bus_size_t off) { struct ti_sdhci_softc *sc = device_get_softc(dev); uint32_t val32; val32 = RD4(sc, off); /* * If we need to disallow highspeed mode due to the OMAP4 erratum, strip * that flag from the returned capabilities. */ if (off == SDHCI_CAPABILITIES && sc->disable_highspeed) val32 &= ~SDHCI_CAN_DO_HISPD; /* * Force the card-present state if necessary. */ if (off == SDHCI_PRESENT_STATE && sc->force_card_present) val32 |= SDHCI_CARD_PRESENT; return (val32); } static void ti_sdhci_read_multi_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, uint32_t *data, bus_size_t count) { struct ti_sdhci_softc *sc = device_get_softc(dev); bus_read_multi_4(sc->mem_res, off + sc->sdhci_reg_off, data, count); } static void ti_sdhci_write_1(device_t dev, struct sdhci_slot *slot, bus_size_t off, uint8_t val) { struct ti_sdhci_softc *sc = device_get_softc(dev); uint32_t val32; #ifdef MMCCAM uint32_t newval32; if (off == SDHCI_HOST_CONTROL) { val32 = ti_mmchs_read_4(sc, MMCHS_CON); newval32 = val32; if (val & SDHCI_CTRL_8BITBUS) { device_printf(dev, "Custom-enabling 8-bit bus\n"); newval32 |= MMCHS_CON_DW8; } else { device_printf(dev, "Custom-disabling 8-bit bus\n"); newval32 &= ~MMCHS_CON_DW8; } if (newval32 != val32) ti_mmchs_write_4(sc, MMCHS_CON, newval32); } #endif val32 = RD4(sc, off & ~3); val32 &= ~(0xff << (off & 3) * 8); val32 |= (val << (off & 3) * 8); WR4(sc, off & ~3, val32); } static void ti_sdhci_write_2(device_t dev, struct sdhci_slot *slot, bus_size_t off, uint16_t val) { struct ti_sdhci_softc *sc = device_get_softc(dev); uint32_t clkdiv, val32; /* * Translate between the hardware and SDHCI 2.0 or 3.0 representations * of the clock divisor. See the comments in ti_sdhci_read_2() for * details. */ if (off == SDHCI_CLOCK_CONTROL) { clkdiv = (val >> SDHCI_DIVIDER_SHIFT) & SDHCI_DIVIDER_MASK; if (slot->version >= SDHCI_SPEC_300) clkdiv |= ((val >> SDHCI_DIVIDER_HI_SHIFT) & SDHCI_DIVIDER_HI_MASK) << SDHCI_DIVIDER_MASK_LEN; clkdiv *= 2; if (clkdiv > MMCHS_SYSCTL_CLKD_MASK) clkdiv = MMCHS_SYSCTL_CLKD_MASK; val32 = RD4(sc, SDHCI_CLOCK_CONTROL); val32 &= 0xffff0000; val32 |= val & ~(MMCHS_SYSCTL_CLKD_MASK << MMCHS_SYSCTL_CLKD_SHIFT); val32 |= clkdiv << MMCHS_SYSCTL_CLKD_SHIFT; WR4(sc, SDHCI_CLOCK_CONTROL, val32); return; } /* * Standard 32-bit handling of command and transfer mode. */ if (off == SDHCI_TRANSFER_MODE) { sc->cmd_and_mode = (sc->cmd_and_mode & 0xffff0000) | ((uint32_t)val & 0x0000ffff); return; } else if (off == SDHCI_COMMAND_FLAGS) { sc->cmd_and_mode = (sc->cmd_and_mode & 0x0000ffff) | ((uint32_t)val << 16); WR4(sc, SDHCI_TRANSFER_MODE, sc->cmd_and_mode); return; } val32 = RD4(sc, off & ~3); val32 &= ~(0xffff << (off & 3) * 8); val32 |= ((val & 0xffff) << (off & 3) * 8); WR4(sc, off & ~3, val32); } static void ti_sdhci_write_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, uint32_t val) { struct ti_sdhci_softc *sc = device_get_softc(dev); WR4(sc, off, val); } static void ti_sdhci_write_multi_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, uint32_t *data, bus_size_t count) { struct ti_sdhci_softc *sc = device_get_softc(dev); bus_write_multi_4(sc->mem_res, off + sc->sdhci_reg_off, data, count); } static void ti_sdhci_intr(void *arg) { struct ti_sdhci_softc *sc = arg; sdhci_generic_intr(&sc->slot); } static int ti_sdhci_update_ios(device_t brdev, device_t reqdev) { struct ti_sdhci_softc *sc = device_get_softc(brdev); struct sdhci_slot *slot; struct mmc_ios *ios; uint32_t val32, newval32; slot = device_get_ivars(reqdev); ios = &slot->host.ios; /* * There is an 8-bit-bus bit in the MMCHS control register which, when * set, overrides the 1 vs 4 bit setting in the standard SDHCI * registers. Set that bit first according to whether an 8-bit bus is * requested, then let the standard driver handle everything else. */ val32 = ti_mmchs_read_4(sc, MMCHS_CON); newval32 = val32; if (ios->bus_width == bus_width_8) newval32 |= MMCHS_CON_DW8; else newval32 &= ~MMCHS_CON_DW8; if (ios->bus_mode == opendrain) newval32 |= MMCHS_CON_OD; else /* if (ios->bus_mode == pushpull) */ newval32 &= ~MMCHS_CON_OD; if (newval32 != val32) ti_mmchs_write_4(sc, MMCHS_CON, newval32); return (sdhci_generic_update_ios(brdev, reqdev)); } static int ti_sdhci_get_ro(device_t brdev, device_t reqdev) { struct ti_sdhci_softc *sc = device_get_softc(brdev); if (sc->disable_readonly) return (0); return (sdhci_fdt_gpio_get_readonly(sc->gpio)); } static bool ti_sdhci_get_card_present(device_t dev, struct sdhci_slot *slot) { struct ti_sdhci_softc *sc = device_get_softc(dev); return (sdhci_fdt_gpio_get_present(sc->gpio)); } static int ti_sdhci_detach(device_t dev) { /* sdhci_fdt_gpio_teardown(sc->gpio); */ return (EBUSY); } static void ti_sdhci_hw_init(device_t dev) { struct ti_sdhci_softc *sc = device_get_softc(dev); uint32_t regval; unsigned long timeout; /* Enable the controller and interface/functional clocks */ if (ti_prcm_clk_enable(sc->mmchs_clk_id) != 0) { device_printf(dev, "Error: failed to enable MMC clock\n"); return; } /* Get the frequency of the source clock */ if (ti_prcm_clk_get_source_freq(sc->mmchs_clk_id, &sc->baseclk_hz) != 0) { device_printf(dev, "Error: failed to get source clock freq\n"); return; } /* Issue a softreset to the controller */ ti_mmchs_write_4(sc, MMCHS_SYSCONFIG, MMCHS_SYSCONFIG_RESET); timeout = 1000; while (!(ti_mmchs_read_4(sc, MMCHS_SYSSTATUS) & MMCHS_SYSSTATUS_RESETDONE)) { if (--timeout == 0) { device_printf(dev, "Error: Controller reset operation timed out\n"); break; } DELAY(100); } /* * Reset the command and data state machines and also other aspects of * the controller such as bus clock and power. * * If we read the software reset register too fast after writing it we * can get back a zero that means the reset hasn't started yet rather * than that the reset is complete. Per TI recommendations, work around * it by reading until we see the reset bit asserted, then read until * it's clear. We also set the SDHCI_QUIRK_WAITFOR_RESET_ASSERTED quirk * so that the main sdhci driver uses this same logic in its resets. */ ti_sdhci_write_1(dev, NULL, SDHCI_SOFTWARE_RESET, SDHCI_RESET_ALL); timeout = 10000; while ((ti_sdhci_read_1(dev, NULL, SDHCI_SOFTWARE_RESET) & SDHCI_RESET_ALL) != SDHCI_RESET_ALL) { if (--timeout == 0) { break; } DELAY(1); } timeout = 10000; while ((ti_sdhci_read_1(dev, NULL, SDHCI_SOFTWARE_RESET) & SDHCI_RESET_ALL)) { if (--timeout == 0) { device_printf(dev, "Error: Software reset operation timed out\n"); break; } DELAY(100); } /* * The attach() routine has examined fdt data and set flags in * slot.host.caps to reflect what voltages we can handle. Set those * values in the CAPA register. The manual says that these values can * only be set once, "before initialization" whatever that means, and * that they survive a reset. So maybe doing this will be a no-op if * u-boot has already initialized the hardware. */ regval = ti_mmchs_read_4(sc, MMCHS_SD_CAPA); if (sc->slot.host.caps & MMC_OCR_LOW_VOLTAGE) regval |= MMCHS_SD_CAPA_VS18; if (sc->slot.host.caps & (MMC_OCR_290_300 | MMC_OCR_300_310)) regval |= MMCHS_SD_CAPA_VS30; ti_mmchs_write_4(sc, MMCHS_SD_CAPA, regval); /* Set initial host configuration (1-bit, std speed, pwr off). */ ti_sdhci_write_1(dev, NULL, SDHCI_HOST_CONTROL, 0); ti_sdhci_write_1(dev, NULL, SDHCI_POWER_CONTROL, 0); /* Set the initial controller configuration. */ ti_mmchs_write_4(sc, MMCHS_CON, MMCHS_CON_DVAL_8_4MS); } static int ti_sdhci_attach(device_t dev) { struct ti_sdhci_softc *sc = device_get_softc(dev); int rid, err; pcell_t prop; phandle_t node; sc->dev = dev; /* * Get the MMCHS device id from FDT. If it's not there use the newbus * unit number (which will work as long as the devices are in order and * none are skipped in the fdt). Note that this is a property we made * up and added in freebsd, it doesn't exist in the published bindings. */ node = ofw_bus_get_node(dev); sc->mmchs_clk_id = ti_hwmods_get_clock(dev); if (sc->mmchs_clk_id == INVALID_CLK_IDENT) { device_printf(dev, "failed to get clock based on hwmods property\n"); } /* * The hardware can inherently do dual-voltage (1p8v, 3p0v) on the first * device, and only 1p8v on other devices unless an external transceiver * is used. The only way we could know about a transceiver is fdt data. * Note that we have to do this before calling ti_sdhci_hw_init() so * that it can set the right values in the CAPA register, which can only * be done once and never reset. */ sc->slot.host.caps |= MMC_OCR_LOW_VOLTAGE; if (sc->mmchs_clk_id == MMC1_CLK || OF_hasprop(node, "ti,dual-volt")) { sc->slot.host.caps |= MMC_OCR_290_300 | MMC_OCR_300_310; } /* * Set the offset from the device's memory start to the MMCHS registers. * Also for OMAP4 disable high speed mode due to erratum ID i626. */ switch (ti_chip()) { #ifdef SOC_OMAP4 case CHIP_OMAP_4: sc->mmchs_reg_off = OMAP4_MMCHS_REG_OFFSET; sc->disable_highspeed = true; break; #endif #ifdef SOC_TI_AM335X case CHIP_AM335X: sc->mmchs_reg_off = AM335X_MMCHS_REG_OFFSET; break; #endif default: panic("Unknown OMAP device\n"); } /* * The standard SDHCI registers are at a fixed offset (the same on all * SoCs) beyond the MMCHS registers. */ sc->sdhci_reg_off = sc->mmchs_reg_off + SDHCI_REG_OFFSET; /* Resource setup. */ rid = 0; sc->mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, RF_ACTIVE); if (!sc->mem_res) { device_printf(dev, "cannot allocate memory window\n"); err = ENXIO; goto fail; } rid = 0; sc->irq_res = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, RF_ACTIVE); if (!sc->irq_res) { device_printf(dev, "cannot allocate interrupt\n"); err = ENXIO; goto fail; } if (bus_setup_intr(dev, sc->irq_res, INTR_TYPE_BIO | INTR_MPSAFE, NULL, ti_sdhci_intr, sc, &sc->intr_cookie)) { device_printf(dev, "cannot setup interrupt handler\n"); err = ENXIO; goto fail; } /* * Set up handling of card-detect and write-protect gpio lines. * * If there is no write protect info in the fdt data, fall back to the * historical practice of assuming that the card is writable. This * works around bad fdt data from the upstream source. The alternative * would be to trust the sdhci controller's PRESENT_STATE register WP * bit, but it may say write protect is in effect when it's not if the * pinmux setup doesn't route the WP signal into the sdchi block. */ sc->gpio = sdhci_fdt_gpio_setup(sc->dev, &sc->slot); if (!OF_hasprop(node, "wp-gpios") && !OF_hasprop(node, "wp-disable")) sc->disable_readonly = true; /* Initialise the MMCHS hardware. */ ti_sdhci_hw_init(dev); /* * The capabilities register can only express base clock frequencies in * the range of 0-63MHz for a v2.0 controller. Since our clock runs * faster than that, the hardware sets the frequency to zero in the * register. When the register contains zero, the sdhci driver expects * slot.max_clk to already have the right value in it. */ sc->slot.max_clk = sc->baseclk_hz; /* * The MMCHS timeout counter is based on the output sdclock. Tell the * sdhci driver to recalculate the timeout clock whenever the output * sdclock frequency changes. */ sc->slot.quirks |= SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK; /* * The MMCHS hardware shifts the 136-bit response data (in violation of * the spec), so tell the sdhci driver not to do the same in software. */ sc->slot.quirks |= SDHCI_QUIRK_DONT_SHIFT_RESPONSE; /* * Reset bits are broken, have to wait to see the bits asserted * before waiting to see them de-asserted. */ sc->slot.quirks |= SDHCI_QUIRK_WAITFOR_RESET_ASSERTED; /* * The controller waits for busy responses. */ sc->slot.quirks |= SDHCI_QUIRK_WAIT_WHILE_BUSY; /* * DMA is not really broken, I just haven't implemented it yet. */ sc->slot.quirks |= SDHCI_QUIRK_BROKEN_DMA; /* * Set up the hardware and go. Note that this sets many of the * slot.host.* fields, so we have to do this before overriding any of * those values based on fdt data, below. */ sdhci_init_slot(dev, &sc->slot, 0); /* * The SDHCI controller doesn't realize it, but we can support 8-bit * even though we're not a v3.0 controller. If there's an fdt bus-width * property, honor it. */ if (OF_getencprop(node, "bus-width", &prop, sizeof(prop)) > 0) { sc->slot.host.caps &= ~(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA); switch (prop) { case 8: sc->slot.host.caps |= MMC_CAP_8_BIT_DATA; /* FALLTHROUGH */ case 4: sc->slot.host.caps |= MMC_CAP_4_BIT_DATA; break; case 1: break; default: device_printf(dev, "Bad bus-width value %u\n", prop); break; } } /* * If the slot is flagged with the non-removable property, set our flag * to always force the SDHCI_CARD_PRESENT bit on. */ node = ofw_bus_get_node(dev); if (OF_hasprop(node, "non-removable")) sc->force_card_present = true; bus_generic_probe(dev); bus_generic_attach(dev); sdhci_start_slot(&sc->slot); return (0); fail: if (sc->intr_cookie) bus_teardown_intr(dev, sc->irq_res, sc->intr_cookie); if (sc->irq_res) bus_release_resource(dev, SYS_RES_IRQ, 0, sc->irq_res); if (sc->mem_res) bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->mem_res); return (err); } static int ti_sdhci_probe(device_t dev) { if (!ofw_bus_status_okay(dev)) return (ENXIO); if (ofw_bus_search_compatible(dev, compat_data)->ocd_data != 0) { device_set_desc(dev, "TI MMCHS (SDHCI 2.0)"); return (BUS_PROBE_DEFAULT); } return (ENXIO); } static device_method_t ti_sdhci_methods[] = { /* Device interface */ DEVMETHOD(device_probe, ti_sdhci_probe), DEVMETHOD(device_attach, ti_sdhci_attach), DEVMETHOD(device_detach, ti_sdhci_detach), /* Bus interface */ DEVMETHOD(bus_read_ivar, sdhci_generic_read_ivar), DEVMETHOD(bus_write_ivar, sdhci_generic_write_ivar), /* MMC bridge interface */ DEVMETHOD(mmcbr_update_ios, ti_sdhci_update_ios), DEVMETHOD(mmcbr_request, sdhci_generic_request), DEVMETHOD(mmcbr_get_ro, ti_sdhci_get_ro), DEVMETHOD(mmcbr_acquire_host, sdhci_generic_acquire_host), DEVMETHOD(mmcbr_release_host, sdhci_generic_release_host), /* SDHCI registers accessors */ DEVMETHOD(sdhci_read_1, ti_sdhci_read_1), DEVMETHOD(sdhci_read_2, ti_sdhci_read_2), DEVMETHOD(sdhci_read_4, ti_sdhci_read_4), DEVMETHOD(sdhci_read_multi_4, ti_sdhci_read_multi_4), DEVMETHOD(sdhci_write_1, ti_sdhci_write_1), DEVMETHOD(sdhci_write_2, ti_sdhci_write_2), DEVMETHOD(sdhci_write_4, ti_sdhci_write_4), DEVMETHOD(sdhci_write_multi_4, ti_sdhci_write_multi_4), DEVMETHOD(sdhci_get_card_present, ti_sdhci_get_card_present), DEVMETHOD_END }; static devclass_t ti_sdhci_devclass; static driver_t ti_sdhci_driver = { "sdhci_ti", ti_sdhci_methods, sizeof(struct ti_sdhci_softc), }; DRIVER_MODULE(sdhci_ti, simplebus, ti_sdhci_driver, ti_sdhci_devclass, NULL, NULL); MODULE_DEPEND(sdhci_ti, sdhci, 1, 1, 1); #ifndef MMCCAM MMC_DECLARE_BRIDGE(sdhci_ti); #endif