/* * Qualcomm Atheros OUI and vendor specific assignments * Copyright (c) 2014-2017, Qualcomm Atheros, Inc. * Copyright (c) 2018, The Linux Foundation * * This software may be distributed under the terms of the BSD license. * See README for more details. */ #ifndef QCA_VENDOR_H #define QCA_VENDOR_H /* * This file is a registry of identifier assignments from the Qualcomm Atheros * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers * can be assigned through normal review process for changes to the upstream * hostap.git repository. */ #define OUI_QCA 0x001374 /** * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs */ enum qca_radiotap_vendor_ids { QCA_RADIOTAP_VID_WLANTEST = 0, }; /** * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers * * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0 * * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event * * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use * internal BSS-selection. This command uses * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy * for the current connection (i.e., changes policy set by the nl80211 * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be * included to indicate which BSS to use in case roaming is disabled. * * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency * ranges to avoid to reduce issues due to interference or internal * co-existence information in the driver. The event data structure is * defined in struct qca_avoid_freq_list. * * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support * for DFS offloading. * * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass * NAN Request/Response and NAN Indication messages. These messages are * interpreted between the framework and the firmware component. While * sending the command from userspace to the driver, payload is not * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN * is used when receiving vendor events in userspace from the driver. * * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be * used to configure PMK to the driver even when not connected. This can * be used to request offloading of key management operations. Only used * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. * * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of * NL80211_CMD_ROAM event with optional attributes including information * from offloaded key management operation. Uses * enum qca_wlan_vendor_attr_roam_auth attributes. Only used * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. * * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to * invoke the ACS function in device and pass selected channels to * hostapd. * * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features * supported by the driver. enum qca_wlan_vendor_features defines * the possible features. * * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver, * which supports DFS offloading, to indicate a channel availability check * start. * * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver, * which supports DFS offloading, to indicate a channel availability check * completion. * * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver, * which supports DFS offloading, to indicate that the channel availability * check aborted, no change to the channel status. * * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by * driver, which supports DFS offloading, to indicate that the * Non-Occupancy Period for this channel is over, channel becomes usable. * * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver, * which supports DFS offloading, to indicate a radar pattern has been * detected. The channel is now unusable. * * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap * based on enum wifi_logger_supported_features. Attributes defined in * enum qca_wlan_vendor_attr_get_logger_features. * * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the * attribute for this command. Attributes defined in * enum qca_wlan_vendor_attr_wifi_logger_start. * * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS * capabilities of the driver, parameters includes the attributes defined * in enum qca_wlan_vendor_attr_tdls_get_capabilities. * * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload * sending of certain periodic IP packet to firmware, attributes defined in * enum qca_wlan_vendor_attr_offloaded_packets. * * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI * monitoring, defines min and max RSSI which are configured for RSSI * monitoring. Also used to notify the RSSI breach and provides the BSSID * and RSSI value that was breached. Attributes defined in * enum qca_wlan_vendor_attr_rssi_monitoring. * * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN * Data Path (NDP) related operations, attributes defined in * enum qca_wlan_vendor_attr_ndp_params. * * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable * Neighbour Discovery offload, attributes defined in * enum qca_wlan_vendor_attr_nd_offload. * * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various * configuration parameter for BPF packet filter, attributes defined in * enum qca_wlan_vendor_attr_packet_filter. * * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware * maximum supported size, attributes defined in * enum qca_wlan_vendor_drv_info. * * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various * data about wake reasons and datapath IP statistics, attributes defined * in enum qca_wlan_vendor_attr_wake_stats. * * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration * for IEEE 802.11 communicating outside the context of a basic service * set, called OCB command. Uses the attributes defines in * enum qca_wlan_vendor_attr_ocb_set_config. * * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB * UTC time. Use the attributes defines in * enum qca_wlan_vendor_attr_ocb_set_utc_time. * * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start * sending OCB timing advert frames. Uses the attributes defines in * enum qca_wlan_vendor_attr_ocb_start_timing_advert. * * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop * OCB timing advert. Uses the attributes defines in * enum qca_wlan_vendor_attr_ocb_stop_timing_advert. * * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF * timer value. Uses the attributes defines in * enum qca_wlan_vendor_attr_ocb_get_tsf_resp. * * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: Command/event to update the * link properties of the respective interface. As an event, is used * to notify the connected station's status. The attributes for this * command are defined in enum qca_wlan_vendor_attr_link_properties. * * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to * start the P2P Listen offload function in device and pass the listen * channel, period, interval, count, device types, and vendor specific * information elements to the device driver and firmware. * Uses the attributes defines in * enum qca_wlan_vendor_attr_p2p_listen_offload. * * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to * indicate stop request/response of the P2P Listen offload function in * device. As an event, it indicates either the feature stopped after it * was already running or feature has actually failed to start. Uses the * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload. * * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts * beaconing, this sub command provides the driver, the frequencies on the * 5 GHz band to check for any radar activity. Driver selects one channel * from this priority list provided through * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts * to check for radar activity on it. If no radar activity is detected * during the channel availability check period, driver internally switches * to the selected frequency of operation. If the frequency is zero, driver * internally selects a channel. The status of this conditional switch is * indicated through an event using the same sub command through * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch. * * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the * attributes defined in enum qca_wlan_gpio_attr. * * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities. * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which * capabilities are to be fetched and other * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the * requested capabilities. * * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension. * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this * command and event. * * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for * indoor location features. Capabilities are reported in * QCA_WLAN_VENDOR_ATTR_LOC_CAPA. * * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM * (fine timing measurement) session with one or more peers. * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS. * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT * events will be reported, followed by * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate * end of session. * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6 * * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session. * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with * status code indicating session was aborted. * * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement * results for one peer. Results are reported in * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS. * * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when * FTM session is finished, either successfully or aborted by * request. * * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether * to enable or disable the responder. LCI/LCR reports can be * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple * times to update the LCI/LCR reports. * * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of * arrival) measurement with a single peer. Specify peer MAC address in * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel * scan results cache and use the frequency from there). * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE. * Measurement result is reported in * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event. * * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. * * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports * the AOA measurement result. * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. * success/failure status is reported in * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS. * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. * The antenna array(s) used in the measurement are reported in * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK. * * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given * data as per the given parameters. * * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a * specific chain. * * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level * configuration for a DMG RF sector. Specify sector index in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules * to return sector information for in * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the * exact time where information was captured in * QCA_WLAN_VENDOR_ATTR_TSF. * * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level * configuration for a DMG RF sector. Specify sector index in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration * for one or more DMG RF modules in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. * * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected * DMG RF sector for a station. This is the sector that the HW * will use to communicate with the station. Specify the MAC address * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not * needed for unassociated station). Specify sector type to return in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. * Also return the exact time where the information was captured * in QCA_WLAN_VENDOR_ATTR_TSF. * * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the * selected DMG RF sector for a station. This is the sector that * the HW will use to communicate with the station. * Specify the MAC address of associated station/AP/PCP in * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. * The selected sector will be locked such that it will not be * modified like it normally does (for example when station * moves around). To unlock the selected sector for a station * pass the special value 0xFFFF in the sector index. To unlock * all connected stations also pass a broadcast MAC address. * * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior * in the host driver. The different TDLS configurations are defined * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. * * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE * capabilities. The response uses the attributes defined in * enum qca_wlan_vendor_attr_get_he_capabilities. * * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command * carries the scan cookie of the corresponding scan request. The scan * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE. * * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific * Absorption Rate (SAR) power limits. A critical regulation for * FCC compliance, OEMs require methods to set SAR limits on TX * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits * attributes are used with this command. * * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the * host driver for offloading the implementation of Auto Channel Selection * (ACS) to an external user space entity. This interface is used as the * event from the host driver to the user space entity and also as the * request from the user space entity to the host driver. The event from * the host driver is used by the user space entity as an indication to * start the ACS functionality. The attributes used by this event are * represented by the enum qca_wlan_vendor_attr_external_acs_event. * User space entity uses the same interface to inform the host driver with * selected channels after the ACS operation using the attributes defined * by enum qca_wlan_vendor_attr_external_acs_channels. * * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the * requisite information leading to a power save failure. The information * carried as part of this event is represented by the * enum qca_attr_chip_power_save_failure attributes. * * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics * collection. Uses attributes defined in enum qca_attr_nud_stats_set. * * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These * statistics are represented by the enum qca_attr_nud_stats_get * attributes. * * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch * the BSS transition status, whether accept or reject, for a list of * candidate BSSIDs provided by the userspace. This uses the vendor * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response * the driver shall specify array of * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. * * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a * specific QCA module. The trace levels are represented by * enum qca_attr_trace_level attributes. * * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement * Protocol antenna limit in different modes. See enum * qca_wlan_vendor_attr_brp_ant_limit_mode. * * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) * identifying the operation in success case. * * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to * be stopped. * * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the * specific interface. This can be used to modify some of the low level * scan parameters (off channel dwell time, home channel time) in the * driver/firmware. These parameters are maintained within the host driver. * This command is valid only when the interface is in the connected state. * These scan parameters shall be reset by the driver/firmware once * disconnected. The attributes used with this command are defined in * enum qca_wlan_vendor_attr_active_tos. * * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the * driver has detected an internal failure. This event carries the * information indicating the reason that triggered this detection. The * attributes for this command are defined in * enum qca_wlan_vendor_attr_hang. * * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values * of spectral parameters used. The spectral scan parameters are specified * by enum qca_wlan_vendor_attr_spectral_scan. * * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats * for spectral scan functionality. The debug stats are specified by * enum qca_wlan_vendor_attr_spectral_diag_stats. * * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral * scan system capabilities. The capabilities are specified * by enum qca_wlan_vendor_attr_spectral_cap. * * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current * status of spectral scan. The status values are specified * by enum qca_wlan_vendor_attr_spectral_scan_status. * * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush * peer pending packets. Specify the peer MAC address in * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed * in enum qca_wlan_vendor_attr_flush_pending. * * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative * RF Operating Parameter (RROP) information. The attributes for this * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is * intended for use by external Auto Channel Selection applications. * * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate * (SAR) power limits. This is a companion to the command * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the * settings currently in use. The attributes returned by this command are * defined by enum qca_vendor_attr_sar_limits. * * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of * the WLAN hardware MAC. Also, provides the WLAN netdev interface * information attached to the respective MAC. * This works both as a query (user space asks the current mode) or event * interface (driver advertising the current mode to the user space). * Driver does not trigger this event for temporary hardware mode changes. * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion, * channel change, etc.) are updated with this event. Attributes for this * interface are defined in enum qca_wlan_vendor_attr_mac. * * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold * per peer per TID. Attributes for this command are define in * enum qca_wlan_set_qdepth_thresh_attr. * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action * guide for WLAN driver. Request to suspend of driver and FW if the * temperature is higher than the suspend threshold; resume action is * requested to driver if the temperature is lower than the resume * threshold. In user poll mode, request temperature data by user. For test * purpose, getting thermal shutdown configuration parameters is needed. * Attributes for this interface are defined in * enum qca_wlan_vendor_attr_thermal_cmd. * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from * driver. Thermal temperature and indication of resume completion are * reported as thermal events. The attributes for this command are defined * in enum qca_wlan_vendor_attr_thermal_event. * * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi * test configuration. Attributes for this command are defined in * enum qca_wlan_vendor_attr_wifi_test_config. * * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an * RX filter to receive frames from stations that are active on the * operating channel, but not associated with the local device (e.g., STAs * associated with other APs). Filtering is done based on a list of BSSIDs * and STA MAC addresses added by the user. This command is also used to * fetch the statistics of unassociated stations. The attributes used with * this command are defined in enum qca_wlan_vendor_attr_bss_filter. * * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, * carried a payload which was a binary blob of data. The command was not * extendable to send more information. The newer version carries the * legacy blob encapsulated within an attribute and can be extended with * additional vendor attributes that can enhance the NAN command interface. * @QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT: Event to indicate scan triggered * or stopped within driver/firmware in order to initiate roaming. The * attributes used with this event are defined in enum * qca_wlan_vendor_attr_roam_scan. Some drivers may not send these events * in few cases, e.g., if the host processor is sleeping when this event * is generated in firmware. * * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to * configure parameters per peer to capture Channel Frequency Response * (CFR) and enable Periodic CFR capture. The attributes for this command * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr. * * @QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT: Event to indicate changes * in throughput dynamically. The driver estimates the throughput based on * number of packets being transmitted/received per second and indicates * the changes in throughput to user space. Userspace tools can use this * information to configure kernel's TCP parameters in order to achieve * peak throughput. Optionally, the driver will also send guidance on * modifications to kernel's TCP parameters which can be referred by * userspace tools. The attributes used with this event are defined in enum * qca_wlan_vendor_attr_throughput_change. * * @QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG: This command is used to set * priorities among different types of traffic during coex scenarios. * Current supported prioritization is among WLAN/BT/ZIGBEE with different * profiles mentioned in enum qca_coex_config_profiles. The associated * attributes used with this command are defined in enum * qca_vendor_attr_coex_config. * * Based on the config provided, FW will boost the weight and prioritize * the traffic for that subsystem (WLAN/BT/Zigbee). */ enum qca_nl80211_vendor_subcmds { QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, QCA_NL80211_VENDOR_SUBCMD_TEST = 1, /* subcmds 2..8 not yet allocated */ QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, QCA_NL80211_VENDOR_SUBCMD_NAN = 12, QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20, QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21, QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22, QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23, QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24, QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25, QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26, QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27, QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28, QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29, QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30, QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31, QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32, QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33, QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41, QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, /* 43..49 - reserved for QCA */ QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, /* 53 - reserved - was used by QCA, but not in use anymore */ QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65, QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66, QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67, QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68, QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69, QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70, QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71, QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72, QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73, /* Wi-Fi configuration subcommands */ QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, QCA_NL80211_VENDOR_SUBCMD_NDP = 81, QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, /* 86-90 - reserved for QCA */ QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, /* 110..114 - reserved for QCA */ QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115, /* 116..117 - reserved for QCA */ QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, QCA_NL80211_VENDOR_SUBCMD_TSF = 119, QCA_NL80211_VENDOR_SUBCMD_WISA = 120, /* 121 - reserved for QCA */ QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, /* FTM/indoor location subcommands */ QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, /* DMG low level RF sector operations */ QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, QCA_NL80211_VENDOR_SUBCMD_HANG = 157, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, /* Flush peer pending data */ QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162, QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, /* Thermal shutdown commands to protect wifi chip */ QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167, QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168, /* Wi-Fi test configuration subcommand */ QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, /* Frame filter operations for other BSSs/unassociated STAs */ QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER = 170, QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT = 172, QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173, QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175, }; enum qca_wlan_vendor_attr { QCA_WLAN_VENDOR_ATTR_INVALID = 0, /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ QCA_WLAN_VENDOR_ATTR_DFS = 1, /* Used only when driver sends vendor events to the userspace under the * command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends * commands to the driver. */ QCA_WLAN_VENDOR_ATTR_NAN = 2, /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined * by enum qca_roaming_policy. */ QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, QCA_WLAN_VENDOR_ATTR_TEST = 8, /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ /* Unsigned 32-bit value. */ QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, /* Unsigned 32-bit value from enum qca_set_band. */ QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, /* Dummy (NOP) attribute for 64 bit padding */ QCA_WLAN_VENDOR_ATTR_PAD = 13, /* Unique FTM session cookie (Unsigned 64 bit). Specified in * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. */ QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, /* Indoor location capabilities, returned by * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. * see enum qca_wlan_vendor_attr_loc_capa. */ QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, /* Array of nested attributes containing information about each peer * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info * for supported attributes for each peer. */ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, /* Array of nested attributes containing measurement results for * one or more peers, reported by the * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. * See enum qca_wlan_vendor_attr_peer_result for list of supported * attributes. */ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, /* Flag attribute for enabling or disabling responder functionality. */ QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER * command to specify the LCI report that will be sent by * the responder during a measurement exchange. The format is * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. */ QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER * command to specify the location civic report that will * be sent by the responder during a measurement exchange. * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. */ QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, /* Session/measurement completion status code, * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT * see enum qca_vendor_attr_loc_session_status. */ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, /* Initial dialog token used by responder (0 if not specified), * unsigned 8 bit value. */ QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if * AOA measurements are needed as part of an FTM session. * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See * enum qca_wlan_vendor_attr_aoa_type. */ QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, /* A bit mask (unsigned 32 bit value) of antenna arrays used * by indoor location measurements. Refers to the antenna * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. */ QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, /* AOA measurement data. Its contents depends on the AOA measurement * type and antenna array mask: * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, * phase of the strongest CIR path for each antenna in the measured * array(s). * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 * values, phase and amplitude of the strongest CIR path for each * antenna in the measured array(s). */ QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to specify the chain number (unsigned 32 bit value) to inquire * the corresponding antenna RSSI value */ QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to report the specific antenna RSSI value (unsigned 32 bit value) */ QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, /* Frequency in MHz, various uses. Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_FREQ = 28, /* TSF timer value, unsigned 64 bit value. * May be returned by various commands. */ QCA_WLAN_VENDOR_ATTR_TSF = 29, /* DMG RF sector index, unsigned 16 bit number. Valid values are * 0..127 for sector indices or 65535 as special value used to * unlock sector selection in * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, /* DMG RF sector type, unsigned 8 bit value. One of the values * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, /* Bitmask of DMG RF modules for which information is requested. Each * bit corresponds to an RF module with the same index as the bit * number. Unsigned 32 bit number but only low 8 bits can be set since * all DMG chips currently have up to 8 RF modules. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, /* Array of nested attributes where each entry is DMG RF sector * configuration for a single RF module. * Attributes for each entry are taken from enum * qca_wlan_vendor_attr_dmg_rf_sector_cfg. * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command * to report frame aggregation statistics to userspace. */ QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, /* Unsigned 8-bit value representing MBO transition reason code as * provided by the AP used by subcommand * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is * specified by the userspace in the request to the driver. */ QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, /* Array of nested attributes, BSSID and status code, used by subcommand * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. * The userspace space specifies the list/array of candidate BSSIDs in * the order of preference in the request. The driver specifies the * status code, for each BSSID in the list, in the response. The * acceptable candidates are listed in the order preferred by the * driver. */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. */ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command * to define the number of antennas to use for BRP. * different purpose in each ANT_LIMIT_MODE: * DISABLE - ignored * EFFECTIVE - upper limit to number of antennas to be used * FORCE - exact number of antennas to be used * unsigned 8 bit value */ QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command * to report the corresponding antenna index to the chain RSSI value */ QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, /* keep last */ QCA_WLAN_VENDOR_ATTR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1, }; enum qca_roaming_policy { QCA_ROAMING_NOT_ALLOWED, QCA_ROAMING_ALLOWED_WITHIN_ESS, }; enum qca_wlan_vendor_attr_roam_auth { QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, /* Indicates the status of re-association requested by user space for * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. * Type u16. * Represents the status code from AP. Use * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the * real status code for failures. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, /* This attribute indicates that the old association was maintained when * a re-association is requested by user space and that re-association * attempt fails (i.e., cannot connect to the requested BSS, but can * remain associated with the BSS with which the association was in * place when being requested to roam). Used along with * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current * re-association status. Type flag. * This attribute is applicable only for re-association failure cases. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, /* This attribute specifies the PMK if one was newly generated during * FILS roaming. This is added to the PMKSA cache and is used in * subsequent connections with PMKSA caching. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11, /* This attribute specifies the PMKID used/generated for the current * FILS roam. This is used in subsequent connections with PMKSA caching. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12, /* A 16-bit unsigned value specifying the next sequence number to use * in ERP message in the currently associated realm. This is used in * doing subsequent ERP based connections in the same realm. */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 }; enum qca_wlan_vendor_attr_p2p_listen_offload { QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one * of the social channels. */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, /* A 32-bit unsigned value; the P2P listen offload period (ms). */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, /* A 32-bit unsigned value; the P2P listen interval duration (ms). */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, /* A 32-bit unsigned value; number of interval times the firmware needs * to run the offloaded P2P listen operation before it stops. */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, /* An array of arbitrary binary data with one or more 8-byte values. * The device types include both primary and secondary device types. */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, /* An array of unsigned 8-bit characters; vendor information elements. */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, /* A 32-bit unsigned value; a control flag to indicate whether listen * results need to be flushed to wpa_supplicant. */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, /* A 8-bit unsigned value; reason code for P2P listen offload stop * event. */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, /* keep last */ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 }; enum qca_wlan_vendor_attr_acs_offload { QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL, QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL, QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE, QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED, QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED, QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED, QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH, QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST, QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL, QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL, QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST, /* keep last */ QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ACS_MAX = QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 }; enum qca_wlan_vendor_acs_hw_mode { QCA_ACS_MODE_IEEE80211B, QCA_ACS_MODE_IEEE80211G, QCA_ACS_MODE_IEEE80211A, QCA_ACS_MODE_IEEE80211AD, QCA_ACS_MODE_IEEE80211ANY, }; /** * enum qca_wlan_vendor_features - Vendor device/driver feature flags * * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key * management offload, a mechanism where the station's firmware * does the exchange with the AP to establish the temporal keys * after roaming, rather than having the user space wpa_supplicant do it. * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic * band selection based on channel selection results. * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports * simultaneous off-channel operations. * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P * Listen offload; a mechanism where the station's firmware takes care of * responding to incoming Probe Request frames received from other P2P * Devices whilst in Listen state, rather than having the user space * wpa_supplicant do it. Information from received P2P requests are * forwarded from firmware to host whenever the host processor wakes up. * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA * specific features. * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific * features. * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON * specific features only. If a Device sets this bit but not the * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that * this Device may not support all OCE AP functionalities but can support * only OCE STA-CFON functionalities. * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self * managed regulatory. * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits */ enum qca_wlan_vendor_features { QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */ }; /** * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication * * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to * the offloaded data. * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded * data. * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload * indication. */ enum qca_wlan_vendor_attr_data_offload_ind { QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, /* keep last */ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set * OCB config * * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the * configuration * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be * scheduled * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel * information * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL * active state configuration * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as * OCB_CONFIG_FLAG_80211_FRAME_MODE * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to * use in the case that a packet is sent without a TX control header * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the * last TA received that the local time set by TA is synchronous to other * communicating OCB STAs. */ enum qca_wlan_vendor_attr_ocb_set_config { QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set * UTC time * * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of * 10 bytes * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of * 5 bytes */ enum qca_wlan_vendor_attr_ocb_set_utc_time { QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1, QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2, QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX = QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes * to start sending timing advert frames * * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency * on which to send the frames * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times * the frame is sent in 5 seconds */ enum qca_wlan_vendor_attr_ocb_start_timing_advert { QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1, QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2, QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX = QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes * to stop timing advert * * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel * frequency on which to stop the timing advert */ enum qca_wlan_vendor_attr_ocb_stop_timing_advert { QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1, QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX = QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to * get TSF timer value * * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the * timer * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer */ enum qca_wlan_vendor_attr_ocb_get_tsf_resp { QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1, QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2, QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX = QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1 }; enum qca_vendor_attr_get_preferred_freq_list { QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, /* A 32-unsigned value; the interface type/mode for which the preferred * frequency list is requested (see enum qca_iface_type for possible * values); used in GET_PREFERRED_FREQ_LIST command from user-space to * kernel and in the kernel response back to user-space. */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, /* An array of 32-unsigned values; values are frequency (MHz); sent * from kernel space to user space. */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, /* An array of nested values as per enum qca_wlan_vendor_attr_pcl * attribute. Each element contains frequency (MHz), weight, and flag * bit mask indicating how the frequency should be used in P2P * negotiation; sent from kernel space to user space. */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL, /* keep last */ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 }; enum qca_vendor_attr_probable_oper_channel { QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, /* 32-bit unsigned value; indicates the connection/iface type likely to * come on this channel (see enum qca_iface_type). */ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, /* keep last */ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 }; enum qca_iface_type { QCA_IFACE_TYPE_STA, QCA_IFACE_TYPE_AP, QCA_IFACE_TYPE_P2P_CLIENT, QCA_IFACE_TYPE_P2P_GO, QCA_IFACE_TYPE_IBSS, QCA_IFACE_TYPE_TDLS, }; enum qca_set_band { QCA_SETBAND_AUTO, QCA_SETBAND_5G, QCA_SETBAND_2G, }; /** * enum qca_access_policy - Access control policy * * Access control policy is applied on the configured IE * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. * * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match * the specific configuration (IE) set, i.e., allow all the * connections which do not match the configuration. * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match * the specific configuration (IE) set, i.e., deny all the * connections which do not match the configuration. */ enum qca_access_policy { QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, }; /** * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32) * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized * SOC timer value at TSF capture */ enum qca_vendor_attr_tsf_cmd { QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TSF_CMD, QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TSF_MAX = QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 }; /** * enum qca_tsf_operation: TSF driver commands * @QCA_TSF_CAPTURE: Initiate TSF Capture * @QCA_TSF_GET: Get TSF capture value * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value */ enum qca_tsf_cmd { QCA_TSF_CAPTURE, QCA_TSF_GET, QCA_TSF_SYNC_GET, }; /** * enum qca_vendor_attr_wisa_cmd * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32) * WISA setup vendor commands */ enum qca_vendor_attr_wisa_cmd { QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WISA_MODE, QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WISA_MAX = QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 }; /* IEEE 802.11 Vendor Specific elements */ /** * enum qca_vendor_element_id - QCA Vendor Specific element types * * These values are used to identify QCA Vendor Specific elements. The * payload of the element starts with the three octet OUI (OUI_QCA) and * is followed by a single octet type which is defined by this enum. * * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. * This element can be used to specify preference order for supported * channels. The channels in this list are in preference order (the first * one has the highest preference) and are described as a pair of * (global) Operating Class and Channel Number (each one octet) fields. * * This extends the standard P2P functionality by providing option to have * more than one preferred operating channel. When this element is present, * it replaces the preference indicated in the Operating Channel attribute. * For supporting other implementations, the Operating Channel attribute is * expected to be used with the highest preference channel. Similarly, all * the channels included in this Preferred channel list element are * expected to be included in the Channel List attribute. * * This vendor element may be included in GO Negotiation Request, P2P * Invitation Request, and Provision Discovery Request frames. * * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID. The payload of this * vendor specific element is defined by the latest P802.11ax draft. * Please note that the draft is still work in progress and this element * payload is subject to change. * * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID. The payload of this * vendor specific element is defined by the latest P802.11ax draft. * Please note that the draft is still work in progress and this element * payload is subject to change. * * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set * element). * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID extension. The payload of * this vendor specific element is defined by the latest P802.11ax draft * (not including the Element ID Extension field). Please note that the * draft is still work in progress and this element payload is subject to * change. * * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID extension. The payload of * this vendor specific element is defined by the latest P802.11ax draft * (not including the Element ID Extension field). Please note that the * draft is still work in progress and this element payload is subject to * change. * * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. * This element can be used for pre-standard publication testing of HE * before P802.11ax draft assigns the element ID extension. The payload of * this vendor specific element is defined by the latest P802.11ax draft * (not including the Element ID Extension field). Please note that the * draft is still work in progress and this element payload is subject to * change. */ enum qca_vendor_element_id { QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, QCA_VENDOR_ELEM_HE_CAPAB = 1, QCA_VENDOR_ELEM_HE_OPER = 2, QCA_VENDOR_ELEM_RAPS = 3, QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, }; /** * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes * * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes * with frequencies to be scanned (in MHz) * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported * rates to be included * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests * at non CCK rate in 2GHz band * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the * driver for the specific scan request * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan * request decoded as in enum scan_status * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation * scan flag is set * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with * randomisation * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the * specific BSSID to scan for. */ enum qca_wlan_vendor_attr_scan { QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1, QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2, QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3, QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4, QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5, QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6, QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7, QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8, QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9, QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10, QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11, QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SCAN_MAX = QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 }; /** * enum scan_status - Specifies the valid values the vendor scan attribute * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take * * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with * new scan results * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between */ enum scan_status { VENDOR_SCAN_STATUS_NEW_RESULTS, VENDOR_SCAN_STATUS_ABORTED, VENDOR_SCAN_STATUS_MAX, }; /** * enum qca_vendor_attr_ota_test - Specifies the values for vendor * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test */ enum qca_vendor_attr_ota_test { QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, /* 8-bit unsigned value to indicate if OTA test is enabled */ QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, /* keep last */ QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 }; /** * enum qca_vendor_attr_txpower_scale - vendor sub commands index * * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value */ enum qca_vendor_attr_txpower_scale { QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, /* 8-bit unsigned value to indicate the scaling of tx power */ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, /* keep last */ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 }; /** * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease * * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. */ enum qca_vendor_attr_txpower_decr_db { QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, /* 8-bit unsigned value to indicate the reduction of TX power in dB for * a virtual interface. */ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, /* keep last */ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 }; /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. */ enum qca_wlan_vendor_attr_config { QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, /* Unsigned 32-bit value to set the DTIM period. * Whether the wifi chipset wakes at every dtim beacon or a multiple of * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 * DTIM beacons. */ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, /* Unsigned 32-bit value to set the wifi_iface stats averaging factor * used to calculate statistics like average the TSF offset or average * number of frame leaked. * For instance, upon Beacon frame reception: * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 * For instance, when evaluating leaky APs: * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 */ QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, /* Unsigned 32-bit value to configure guard time, i.e., when * implementing IEEE power management based on frame control PM bit, how * long the driver waits before shutting down the radio and after * receiving an ACK frame for a Data frame with PM bit set. */ QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, /* Unsigned 32-bit value to change the FTM capability dynamically */ QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, /* Unsigned 16-bit value to configure maximum TX rate dynamically */ QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, /* Unsigned 32-bit value to configure the number of continuous * Beacon Miss which shall be used by the firmware to penalize * the RSSI. */ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, /* Unsigned 8-bit value to configure the channel avoidance indication * behavior. Firmware to send only one indication and ignore duplicate * indications when set to avoid multiple Apps wakeups. */ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, /* 8-bit unsigned value to configure the maximum TX MPDU for * aggregation. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, /* 8-bit unsigned value to configure the maximum RX MPDU for * aggregation. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, /* 8-bit unsigned value to configure the Non aggregrate/11g sw * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, /* 8-bit unsigned value to configure the aggregrate sw * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, /* 8-bit unsigned value to configure the MGMT frame * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, /* 8-bit unsigned value to configure the CTRL frame * retry threshold (0 disable, 31 max). */ QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, /* 8-bit unsigned value to configure the propagation delay for * 2G/5G band (0~63, units in us) */ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, /* Unsigned 32-bit value to configure the number of unicast TX fail * packet count. The peer is disconnected once this threshold is * reached. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, /* Attribute used to set scan default IEs to the driver. * * These IEs can be used by scan operations that will be initiated by * the driver/firmware. * * For further scan requests coming to the driver, these IEs should be * merged with the IEs received along with scan request coming to the * driver. If a particular IE is present in the scan default IEs but not * present in the scan request, then that IE should be added to the IEs * sent in the Probe Request frames for that scan request. */ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, /* Unsigned 32-bit attribute for generic commands */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, /* Unsigned 32-bit value attribute for generic commands */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, /* Unsigned 32-bit data attribute for generic command response */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, /* Unsigned 32-bit length attribute for * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, /* Unsigned 32-bit flags attribute for * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, /* Unsigned 32-bit, defining the access policy. * See enum qca_access_policy. Used with * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, /* Sets the list of full set of IEs for which a specific access policy * has to be applied. Used along with * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. * Zero length payload can be used to clear this access constraint. */ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, /* Unsigned 32-bit, specifies the interface index (netdev) for which the * corresponding configurations are applied. If the interface index is * not specified, the configurations are attributed to the respective * wiphy. */ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, /* 8-bit unsigned value to configure the driver and below layers to * ignore the assoc disallowed set by APs while connecting * 1-Ignore, 0-Don't ignore */ QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, /* 32-bit unsigned value to trigger antenna diversity features: * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, /* 32-bit unsigned value to configure specific chain antenna */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, /* 32-bit unsigned value to trigger cycle selftest * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, /* 32-bit unsigned to configure the cycle time of selftest * the unit is micro-second */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, /* 32-bit unsigned value to set reorder timeout for AC_VO */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, /* 32-bit unsigned value to set reorder timeout for AC_VI */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, /* 32-bit unsigned value to set reorder timeout for AC_BE */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, /* 32-bit unsigned value to set reorder timeout for AC_BK */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, /* 6-byte MAC address to point out the specific peer */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, /* 32-bit unsigned value to set window size for specific peer */ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, /* 32-bit unsigned value to configure 5 or 10 MHz channel width for * station device while in disconnect state. The attribute use the * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or * 10 MHz channel width, the station will not connect to a BSS using 20 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to * clear this constraint. */ QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, /* 32-bit unsigned value to configure the propagation absolute delay * for 2G/5G band (units in us) */ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, /* 32-bit unsigned value to set probe period */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, /* 32-bit unsigned value to set stay period */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, /* 32-bit unsigned value to set snr diff */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, /* 32-bit unsigned value to set probe dwell time */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, /* 32-bit unsigned value to set mgmt snr weight */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, /* 32-bit unsigned value to set data snr weight */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, /* 32-bit unsigned value to set ack snr weight */ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, /* 32-bit unsigned value to configure the listen interval. * This is in units of beacon intervals. This configuration alters * the negotiated listen interval with the AP during the connection. * It is highly recommended to configure a value less than or equal to * the one negotiated during the association. Configuring any greater * value can have adverse effects (frame loss, AP disassociating STA, * etc.). */ QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, /* * 8 bit unsigned value that is set on an AP/GO virtual interface to * disable operations that would cause the AP/GO to leave its operating * channel. * * This will restrict the scans to the AP/GO operating channel and the * channels of the other band, if DBS is supported.A STA/CLI interface * brought up after this setting is enabled, will be restricted to * connecting to devices only on the AP/GO interface's operating channel * or on the other band in DBS case. P2P supported channel list is * modified, to only include AP interface's operating-channel and the * channels of the other band if DBS is supported. * * These restrictions are only applicable as long as the AP/GO interface * is alive. If the AP/GO interface is brought down then this * setting/restriction is forgotten. * * If this variable is set on an AP/GO interface while a multi-channel * concurrent session is active, it has no effect on the operation of * the current interfaces, other than restricting the scan to the AP/GO * operating channel and the other band channels if DBS is supported. * However, if the STA is brought down and restarted then the new STA * connection will either be formed on the AP/GO channel or on the * other band in a DBS case. This is because of the scan being * restricted on these channels as mentioned above. * * 1-Restrict / 0-Don't restrict offchannel operations. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, /* * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) * on an interface. * 1 - Enable, 0 - Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, /* * 8 bit unsigned value to globally enable/disable scan * 1 - Enable, 0 - Disable. */ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, /* 8-bit unsigned value to set the total beacon miss count * This parameter will set the total beacon miss count. */ QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, /* Unsigned 32-bit value to configure the number of continuous * Beacon Miss which shall be used by the firmware to penalize * the RSSI for BTC. */ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, /* 8-bit unsigned value to configure the driver and below layers to * enable/disable all FILS features. * 0-enable, 1-disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, /* 16-bit unsigned value to configure the level of WLAN latency * module. See enum qca_wlan_vendor_attr_config_latency_level. */ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, /* 8-bit unsigned value indicating the driver to use the RSNE as-is from * the connect interface. Exclusively used for the scenarios where the * device is used as a test bed device with special functionality and * not recommended for production. This helps driver to not validate the * RSNE passed from user space and thus allow arbitrary IE data to be * used for testing purposes. * 1-enable, 0-disable. * Applications set/reset this configuration. If not reset, this * parameter remains in use until the driver is unloaded. */ QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, /* 8-bit unsigned value to trigger green Tx power saving. * 1-Enable, 0-Disable */ QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration */ enum qca_wlan_vendor_attr_sap_config { QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, /* 1 - reserved for QCA */ /* List of frequencies on which AP is expected to operate. * This is irrespective of ACS configuration. This list is a priority * based one and is looked for before the AP is created to ensure the * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in * the system. */ QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP * conditional channel switch */ enum qca_wlan_vendor_attr_sap_conditional_chan_switch { QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, /* Priority based frequency list (an array of u32 values in host byte * order) */ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, /* Status of the conditional switch (u32). * 0: Success, Non-zero: Failure */ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, }; /** * enum qca_wlan_gpio_attr - Parameters for GPIO configuration */ enum qca_wlan_gpio_attr { QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, /* Unsigned 32-bit attribute for GPIO command */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND, /* Unsigned 32-bit attribute for GPIO PIN number to configure */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM, /* Unsigned 32-bit attribute for GPIO value to configure */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE, /* Unsigned 32-bit attribute for GPIO pull type */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE, /* Unsigned 32-bit attribute for GPIO interrupt mode */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE, /* keep last */ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1 }; /** * qca_wlan_set_qdepth_thresh_attr - Parameters for setting * MSDUQ depth threshold per peer per tid in the target * * Associated Vendor Command: * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH */ enum qca_wlan_set_qdepth_thresh_attr { QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, /* 6-byte MAC address */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, /* Unsigned 32-bit attribute for holding the TID */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, /* Unsigned 32-bit attribute for holding the update mask * bit 0 - Update high priority msdu qdepth threshold * bit 1 - Update low priority msdu qdepth threshold * bit 2 - Update UDP msdu qdepth threshold * bit 3 - Update Non UDP msdu qdepth threshold * rest of bits are reserved */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, /* Unsigned 32-bit attribute for holding the threshold value */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, /* keep last */ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability */ enum qca_wlan_vendor_attr_get_hw_capability { QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, /* Antenna isolation * An attribute used in the response. * The content of this attribute is encoded in a byte array. Each byte * value is an antenna isolation value. The array length is the number * of antennas. */ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, /* Request HW capability * An attribute used in the request. * The content of this attribute is a u32 array for one or more of * hardware capabilities (attribute IDs) that are being requested. Each * u32 value has a value from this * enum qca_wlan_vendor_attr_get_hw_capability * identifying which capabilities are requested. */ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, /* keep last */ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring * offload which is an extension for LL_STATS. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. * If MAC counters do not exceed the threshold, FW will report monitored * link layer counters periodically as this setting. The first report is * always triggered by this timer. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). * For each MAC layer counter, FW holds two copies. One is the current value. * The other is the last report. Once a current counter's increment is larger * than the threshold, FW will indicate that counter to host even if the * monitoring timer does not expire. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same * failure code. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code * 1: TX packet discarded * 2: No ACK * 3: Postpone * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. * Threshold for all monitored parameters. If per counter dedicated threshold * is not enabled, this threshold will take effect. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters * Bit0: TX counter unit in MSDU * Bit1: TX counter unit in MPDU * Bit2: TX counter unit in PPDU * Bit3: TX counter unit in byte * Bit4: Dropped MSDUs * Bit5: Dropped Bytes * Bit6: MPDU retry counter * Bit7: MPDU failure counter * Bit8: PPDU failure counter * Bit9: MPDU aggregation counter * Bit10: MCS counter for ACKed MPDUs * Bit11: MCS counter for Failed MPDUs * Bit12: TX Delay counter * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters * Bit0: MAC RX counter unit in MPDU * Bit1: MAC RX counter unit in byte * Bit2: PHY RX counter unit in PPDU * Bit3: PHY RX counter unit in byte * Bit4: Disorder counter * Bit5: Retry counter * Bit6: Duplication counter * Bit7: Discard counter * Bit8: MPDU aggregation size counter * Bit9: MCS counter * Bit10: Peer STA power state change (wake to sleep) counter * Bit11: Peer STA power save counter, total time in PS mode * Bit12: Probe request counter * Bit13: Other management frames counter * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA * Bit0: Idle time * Bit1: TX time * Bit2: time RX in current bss * Bit3: Out of current bss time * Bit4: Wireless medium busy time * Bit5: RX in bad condition time * Bit6: TX in bad condition time * Bit7: time wlan card not available * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal * Bit0: Per channel SNR counter * Bit1: Per channel noise floor counter * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: * aggregation stats buffer length * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats * buffer for ACKed MPDUs. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats * buffer for failed MPDUs. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: * length of delay stats array. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets * flagged as retransmissions * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets * flagged as duplicated * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX * packets discarded * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation * stats buffer. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs * stats buffer. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe * requests received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt * frames received * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time * there is no TX, nor RX, nor interference. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time * transmitting packets. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time * for receiving. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time * interference detected. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time * receiving packets with errors. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time * TX no-ACK. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time * the chip is unable to work in normal conditions. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time * receiving packets in current BSS. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time * receiving packets not in current BSS. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: * This is a container for per antenna signal stats. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64 * Absolute timestamp from 1970/1/1, unit in ms. After receiving the * message, user layer APP could call gettimeofday to get another * timestamp and calculate transfer delay for the message. * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32 * Real period for this measurement, unit in us. */ enum qca_wlan_vendor_attr_ll_stats_ext { QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, /* Attributes for configurations */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, /* Peer STA power state change */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, /* TX failure event */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, /* MAC counters */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, /* Sub-attributes for PEER_AC_TX */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, /* Sub-attributes for PEER_AC_RX */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, /* Sub-attributes for CCA_BSS */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, /* sub-attribute for BSS_RX_TIME */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, /* Sub-attributes for PEER_SIGNAL */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, /* Sub-attributes for IFACE_BSS */ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 }; /* Attributes for FTM commands and events */ /** * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities * * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See * enum qca_wlan_vendor_attr_loc_capa_flags. * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number * of measurement sessions that can run concurrently. * Default is one session (no session concurrency). * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique * peers that are supported in running sessions. For example, * if the value is 8 and maximum number of sessions is 2, you can * have one session with 8 unique peers, or 2 sessions with 4 unique * peers each, and so on. * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number * of bursts per peer, as an exponent (2^value). Default is 0, * meaning no multi-burst support. * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number * of measurement exchanges allowed in a single burst. * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement * types. A bit mask (unsigned 32 bit value), each bit corresponds * to an AOA type as defined by enum qca_vendor_attr_aoa_type. */ enum qca_wlan_vendor_attr_loc_capa { QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, /* keep last */ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags * * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver * can be configured as an FTM responder (for example, an AP that * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER * will be supported if set. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION * will be supported if set. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder * supports immediate (ASAP) response. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports * requesting AOA measurements as part of an FTM session. */ enum qca_wlan_vendor_attr_loc_capa_flags { QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, }; /** * enum qca_wlan_vendor_attr_ftm_peer_info: Information about * a single peer in a measurement session. * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for * list of supported attributes. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for * secure measurement. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA * measurement every bursts. If 0 or not specified, * AOA measurements will be disabled for this peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where * the measurement frames are exchanged. Optional; if not * specified, try to locate the peer in the kernel scan * results cache and use frequency from there. */ enum qca_wlan_vendor_attr_ftm_peer_info { QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, * per-peer * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request * immediate (ASAP) response from peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request * LCI report from peer. The LCI report includes the absolute * location of the peer in "official" coordinates (similar to GPS). * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request * Location civic report from peer. The LCR includes the location * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, * 11.24.6.7 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, * request a secure measurement. * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. */ enum qca_wlan_vendor_attr_ftm_peer_meas_flags { QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, }; /** * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters * * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements * to perform in a single burst. * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to * perform, specified as an exponent (2^value). * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. */ enum qca_wlan_vendor_attr_ftm_meas_param { QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported * peer. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement * request for this peer. * See enum qca_wlan_vendor_attr_ftm_peer_result_status. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related * to measurement results for this peer. * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when * request failed and peer requested not to send an additional request * for this number of seconds. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, * 9.4.2.22.10. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, * 9.4.2.22.13. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer * overridden some measurement request parameters. See * enum qca_wlan_vendor_attr_ftm_meas_param. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement * results. Each entry is a nested attribute defined * by enum qca_wlan_vendor_attr_ftm_meas. */ enum qca_wlan_vendor_attr_ftm_peer_result { QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ftm_peer_result_status * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results * will be provided. Peer may have overridden some measurement parameters, * in which case overridden parameters will be report by * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable * of performing the measurement request. No more results will be sent * for this peer in this session. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request * failed, and requested not to send an additional request for number * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS * attribute. * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation * failed. Request was not sent over the air. */ enum qca_wlan_vendor_attr_ftm_peer_result_status { QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, }; /** * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags * for measurement result, per-peer * * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, * measurement completed for this peer. No more results will be reported * for this peer in this session. */ enum qca_wlan_vendor_attr_ftm_peer_result_flags { QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, }; /** * enum qca_vendor_attr_loc_session_status: Session completion status code * * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed * successfully. * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted * by request. * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request * was invalid and was not started. * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error * and did not complete normally (for example out of resources). */ enum qca_vendor_attr_loc_session_status { QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, }; /** * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data * * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as * recorded by responder, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at * initiator, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by * initiator, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at * responder, in picoseconds. * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded * during this measurement exchange. Optional and will be provided if * the hardware can measure it. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by * responder. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by * responder. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by * initiator. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by * initiator. Not always provided. * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. */ enum qca_wlan_vendor_attr_ftm_meas { QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, /* keep last */ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type * * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest * CIR (channel impulse response) path for each antenna. * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude * of the strongest CIR path for each antenna. */ enum qca_wlan_vendor_attr_aoa_type { QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX }; /** * enum qca_wlan_vendor_attr_encryption_test - Attributes to * validate encryption engine * * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. * This will be included if the request is for decryption; if not included, * the request is treated as a request for encryption by default. * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value * indicating the key cipher suite. Takes same values as * NL80211_ATTR_KEY_CIPHER. * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value * Key Id to be used for encryption * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. * Key (TK) to be used for encryption/decryption * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. * Packet number to be specified for encryption/decryption * 6 bytes for TKIP/CCMP/GCMP. * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values * representing the 802.11 packet (header + payload + FCS) that * needs to be encrypted/decrypted. * Encrypted/decrypted response from the driver will also be sent * to userspace with the same attribute. */ enum qca_wlan_vendor_attr_encryption_test { QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, /* keep last */ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of * sector for DMG RF sector operations. * * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector */ enum qca_wlan_vendor_attr_dmg_rf_sector_type { QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX }; /** * BRP antenna limit mode * * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force * antenna limit, BRP will be performed as usual. * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal * antennas limit. the hardware may use less antennas than the * maximum limit. * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will * use exactly the specified number of antennas for BRP. */ enum qca_wlan_vendor_attr_brp_ant_limit_mode { QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX }; /** * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for * DMG RF sector configuration for a single RF module. * The values are defined in a compact way which closely matches * the way it is stored in HW registers. * The configuration provides values for 32 antennas and 8 distribution * amplifiers, and together describes the characteristics of the RF * sector - such as a beam in some direction with some gain. * * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index * of RF module for this configuration. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge * amplifier gain index. Unsigned 32 bit number containing * bits for all 32 antennas. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge * amplifier gain index. Unsigned 32 bit number containing * bits for all 32 antennas. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge * amplifier gain index. Unsigned 32 bit number containing * bits for all 32 antennas. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values * for first 16 antennas, 2 bits per antenna. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values * for last 16 antennas, 2 bits per antenna. * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains * DTYPE values (3 bits) for each distribution amplifier, followed * by X16 switch bits for each distribution amplifier. There are * total of 8 distribution amplifiers. */ enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 }; enum qca_wlan_vendor_attr_ll_stats_set { QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_ll_stats_clr { QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, /* Unsigned 32bit bitmap for clearing statistics * All radio statistics 0x00000001 * cca_busy_time (within radio statistics) 0x00000002 * All channel stats (within radio statistics) 0x00000004 * All scan statistics (within radio statistics) 0x00000008 * All interface statistics 0x00000010 * All tx rate statistics (within interface statistics) 0x00000020 * All ac statistics (with in interface statistics) 0x00000040 * All contention (min, max, avg) statistics (within ac statisctics) * 0x00000080. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1, /* Unsigned 8 bit value: Request to stop statistics collection */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2, /* Unsigned 32 bit bitmap: Response from the driver * for the cleared statistics */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3, /* Unsigned 8 bit value: Response from driver/firmware * for the stop request */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_ll_stats_get { QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, /* Unsigned 32 bit value provided by the caller issuing the GET stats * command. When reporting the stats results, the driver uses the same * value to indicate which GET request the results correspond to. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1, /* Unsigned 32 bit value - bit mask to identify what statistics are * requested for retrieval. * Radio Statistics 0x00000001 * Interface Statistics 0x00000020 * All Peer Statistics 0x00000040 * Peer Statistics 0x00000080 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_ll_stats_results { QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, /* Unsigned 32bit value. Used by the driver; must match the request id * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, /* Signed 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, /* Signed 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, /* Signed 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are * nested within the interface stats. */ /* Interface mode, e.g., STA, SOFTAP, IBSS, etc. * Type = enum wifi_interface_mode. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, /* Interface MAC address. An array of 6 Unsigned int8 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, /* Type = enum wifi_connection_state, e.g., DISCONNECTED, * AUTHENTICATING, etc. valid for STA, CLI only. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, /* NULL terminated SSID. An array of 33 Unsigned 8bit values */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, /* BSSID. An array of 6 unsigned 8 bit values */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, /* Country string advertised by AP. An array of 3 unsigned 8 bit * values. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, /* Country string for this association. An array of 3 unsigned 8 bit * values. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could * be nested within the interface stats. */ /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, /* Unsigned int 32 value corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, /* Unsigned int 32 values corresponding to respective AC */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, /* Unsigned 32 bit value. Number of peers */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are * nested within the interface stats. */ /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, /* MAC addr corresponding to respective peer. An array of 6 unsigned * 8 bit values. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, /* Unsigned int 32 bit value representing capabilities corresponding * to respective peer. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, /* Unsigned 32 bit value. Number of rates */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* * are nested within the rate stat. */ /* Wi-Fi Rate - separate attributes defined for individual fields */ /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std * in the units of 0.5 Mbps HT/VHT it would be MCS index */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, /* Unsigned 32 bit value. Bit rate in units of 100 kbps */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be * nested within the peer info stats. */ /* Unsigned int 32 bit value. Number of successfully transmitted data * packets, i.e., with ACK received corresponding to the respective * rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, /* Unsigned int 32 bit value. Number of received data packets * corresponding to the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK * received corresponding to the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, /* Unsigned int 32 bit value. Total number of data packet retries for * the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, /* Unsigned int 32 bit value. Total number of short data packet retries * for the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, /* Unsigned int 32 bit value. Total number of long data packet retries * for the respective rate. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, /* Unsigned 32 bit value. Total number of msecs the radio is awake * accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, /* Unsigned 32 bit value. Total number of msecs the radio is * transmitting accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, /* Unsigned 32 bit value. Total number of msecs the radio is in active * receive accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to all scan accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to NAN accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to GSCAN accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to roam scan accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to PNO scan accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, /* Unsigned 32 bit value. Total number of msecs the radio is awake due * to Hotspot 2.0 scans and GAS exchange accruing over time. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, /* Unsigned 32 bit value. Number of channels. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could * be nested within the channel stats. */ /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, /* Unsigned 32 bit value. Primary 20 MHz channel. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, /* Unsigned 32 bit value. Center frequency (MHz) first segment. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, /* Unsigned 32 bit value. Center frequency (MHz) second segment. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be * nested within the radio stats. */ /* Unsigned int 32 bit value representing total number of msecs the * radio is awake on that channel accruing over time, corresponding to * the respective channel. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, /* Unsigned int 32 bit value representing total number of msecs the CCA * register is busy accruing over time corresponding to the respective * channel. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, /* Signifies the nested list of channel attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, /* Signifies the nested list of peer info attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, /* Signifies the nested list of rate info attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, /* Signifies the nested list of wmm info attributes * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates * that more stats, e.g., peers or radio, are to follow in the next * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. * Otherwise, it is set to 0. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, /* Unsigned 64 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, /* Number of msecs the radio spent in transmitting for each power level */ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, /* Unsigned 32 bit value */ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, /* Unsigned int 32 value. * Pending MSDUs corresponding to respective AC. */ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83, /* keep last */ QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_ll_stats_type { QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, /* keep last */ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for * TDLS configuration to the host driver. * * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode * represents the different TDLS trigger modes. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number * of packets shall meet the criteria for implicit TDLS setup. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD * to initiate a TDLS setup. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate * a TDLS Discovery to the peer. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of * discovery attempts to know the TDLS capability of the peer. A peer is * marked as TDLS not capable if there is no response for all the attempts. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD * number of TX / RX frames meet the criteria for TDLS teardown. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32) * of Tx/Rx packets within a duration * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold * corresponding to the RSSI of the peer below which a TDLS setup is * triggered. * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold * corresponding to the RSSI of the peer above which a TDLS teardown is * triggered. */ enum qca_wlan_vendor_attr_tdls_configuration { QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, /* Attributes configuring the TDLS Implicit Trigger */ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in * the driver * * The following are the different values for * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. * * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown * the TDLS connection to a respective peer comes from the user space. * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN, * TDLS_DISCOVER to do this. * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS * setup/teardown to the eligible peer once the configured criteria * (such as TX/RX threshold, RSSI) is met. The attributes * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to * the different configuration criteria for the TDLS trigger from the * host driver. * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger * the TDLS setup / teardown through the implicit mode only to the * configured MAC addresses (wpa_supplicant, with tdls_external_control=1, * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands). * External mode works on top of the implicit mode. Thus the host driver * is expected to configure in TDLS Implicit mode too to operate in * External mode. * Configuring External mode alone without Implicit mode is invalid. * * All the above implementations work as expected only when the host driver * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing * that the TDLS message exchange is not internal to the host driver, but * depends on wpa_supplicant to do the message exchange. */ enum qca_wlan_vendor_tdls_trigger_mode { QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, }; /** * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 * that is hard-coded in the Board Data File (BDF). * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any * source of SAR power limits, thereby disabling the SAR power * limit feature. * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. * * This enumerates the valid set of values that may be supplied for * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in * the response to an instance of the * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. */ enum qca_vendor_attr_sar_limits_selections { QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, }; /** * enum qca_vendor_attr_sar_limits_spec_modulations - * SAR limits specification modulation * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - * CCK modulation * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - * OFDM modulation * * This enumerates the valid set of values that may be supplied for * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor * command or in the response to an instance of the * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. */ enum qca_vendor_attr_sar_limits_spec_modulations { QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, }; /** * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to * select which SAR power limit table should be used. Valid * values are enumerated in enum * %qca_vendor_attr_sar_limits_selections. The existing SAR * power limit selection is unchanged if this attribute is not * present. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value * which specifies the number of SAR power limit specifications * which will follow. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power * limit specifications. The number of specifications is * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each * specification contains a set of * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A * specification is uniquely identified by the attributes * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always * contains as a payload the attribute * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT, * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is * needed based upon the value of * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to * indicate for which band this specification applies. Valid * values are enumerated in enum %nl80211_band (although not all * bands may be supported by a given device). If the attribute is * not supplied then the specification will be applied to all * supported bands. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value * to indicate for which antenna chain this specification * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the * attribute is not supplied then the specification will be * applied to all chains. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) * value to indicate for which modulation scheme this * specification applies. Valid values are enumerated in enum * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute * is not supplied then the specification will be applied to all * modulation schemes. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) * value to specify the actual power limit value in units of 0.5 * dBm (i.e., a value of 11 represents 5.5 dBm). * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. * * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. * * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. */ enum qca_vendor_attr_sar_limits { QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command. */ enum qca_wlan_vendor_attr_get_wifi_info { QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, }; /* * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command. */ enum qca_wlan_vendor_attr_wifi_logger_start { QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_logger_results { QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, /* Unsigned 32-bit value; must match the request Id supplied by * Wi-Fi HAL in the corresponding subcmd NL msg. */ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, /* Unsigned 32-bit value; used to indicate the size of memory * dump to be allocated. */ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_roaming_config_params { QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, /* Attributes for wifi_set_ssid_white_list */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, /* Attributes for set_roam_params */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, /* Attribute for set_lazy_roam */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, /* Attribute for set_lazy_roam with preferences */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, /* Attribute for set_blacklist bssid params */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, }; /* * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command. */ enum qca_wlan_vendor_attr_roam_subcmd { QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_gscan_config_params { QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND = 2, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS = 3, /* Attributes for input params used by * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command. */ /* Unsigned 32-bit value; channel frequency */ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4, /* Unsigned 32-bit value; dwell time in ms. */ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5, /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6, /* Unsigned 8-bit value; channel class */ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7, /* Unsigned 8-bit value; bucket index, 0 based */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8, /* Unsigned 8-bit value; band. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9, /* Unsigned 32-bit value; desired period, in ms. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10, /* Unsigned 8-bit value; report events semantics. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, /* Unsigned 32-bit value. Followed by a nested array of * GSCAN_CHANNEL_SPEC_* attributes. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes. * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS */ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13, /* Unsigned 32-bit value; base timer period in ms. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, /* Unsigned 32-bit value; number of APs to store in each scan in the * BSSID/RSSI history buffer (keep the highest RSSI APs). */ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake * up AP. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT = 16, /* Unsigned 8-bit value; number of scan bucket specs; followed by a * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size * of the array is determined by NUM_BUCKETS. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes. * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18, /* Unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH = 19, /* Unsigned 32-bit value; maximum number of results to be returned. */ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX = 20, /* An array of 6 x unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, /* Number of hotlist APs as unsigned 32-bit value, followed by a nested * array of AP_THRESHOLD_PARAM attributes and values. The size of the * array is determined by NUM_AP. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes. * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS */ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26, /* Unsigned 32-bit value; number of samples for averaging RSSI. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE = 27, /* Unsigned 32-bit value; number of samples to confirm AP loss. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE = 28, /* Unsigned 32-bit value; number of APs breaching threshold. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, /* Unsigned 32-bit value; number of APs. Followed by an array of * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, /* Unsigned 32-bit value; number of samples to confirm AP loss. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE = 31, /* Unsigned 32-bit value. If max_period is non zero or different than * period, then this bucket is an exponential backoff bucket. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32, /* Unsigned 32-bit value. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33, /* Unsigned 32-bit value. For exponential back off bucket, number of * scans to perform for a given period. */ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34, /* Unsigned 8-bit value; in number of scans, wake up AP after these * many scans. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS = 35, /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command. */ /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE = 36, /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The * size of the array is determined by NUM_SSID. */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_* * attributes. * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38, /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39, /* Unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, /* Unsigned 32-bit value; a bitmask with additional gscan config flag. */ QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43, /* keep last */ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX = QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_gscan_results { QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0, /* Unsigned 32-bit value; must match the request Id supplied by * Wi-Fi HAL in the corresponding subcmd NL msg. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1, /* Unsigned 32-bit value; used to indicate the status response from * firmware/driver for the vendor sub-command. */ QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2, /* GSCAN Valid Channels attributes */ /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3, /* An array of NUM_CHANNELS x unsigned 32-bit value integers * representing channel numbers. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4, /* GSCAN Capabilities attributes */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN = 7, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE = 8, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD = 9, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS = 11, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES = 12, /* GSCAN Attributes used with * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, /* GSCAN attributes used with * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command. */ /* An array of NUM_RESULTS_AVAILABLE x * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_* */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14, /* Unsigned 64-bit value; age of sample at the time of retrieval */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, /* 33 x unsigned 8-bit value; NULL terminated SSID */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16, /* An array of 6 x unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17, /* Unsigned 32-bit value; channel frequency in MHz */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, /* Signed 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, /* Unsigned 16-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, /* Unsigned 16-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, /* Unsigned 32-bit value; size of the IE DATA blob */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the * information elements found in the beacon; this data should be a * packed list of wifi_information_element objects, one after the * other. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, /* Unsigned 8-bit value; set by driver to indicate more scan results are * available. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, /* GSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command. */ /* Unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28, /* GSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command. */ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE * to indicate number of results. * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the * list of results. */ /* GSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command. */ /* An array of 6 x unsigned 8-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL = 30, /* Unsigned 32-bit value. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI = 31, /* A nested array of signed 32-bit RSSI values. Size of the array is * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST = 32, /* GSCAN attributes used with * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command. */ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE * to indicate number of gscan cached results returned. * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate * the list of gscan cached results. */ /* An array of NUM_RESULTS_AVAILABLE x * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_* */ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33, /* Unsigned 32-bit value; a unique identifier for the scan unit. */ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34, /* Unsigned 32-bit value; a bitmask w/additional information about scan. */ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35, /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE * to indicate number of wifi scan results/bssids retrieved by the scan. * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the * list of wifi scan results returned for each cached result block. */ /* GSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. */ /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for * number of results. * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested * list of wifi scan results returned for each * wifi_passpoint_match_result block. * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE. */ /* GSCAN attributes for * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES = 36, /* A nested array of * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_* * attributes. Array size = * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. */ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, /* Unsigned 32-bit value; network block id for the matched network */ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested * list of wifi scan results returned for each * wifi_passpoint_match_result block. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; * ANQP data in the information_element format. */ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID = 43, /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID = 44, QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45, /* Unsigned 32-bit value; a GSCAN Capabilities attribute. * This is used to limit the maximum number of BSSIDs while sending * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with attributes * QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID and * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID. */ QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID = 46, /* keep last */ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX = QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1, }; enum qca_wlan_vendor_attr_pno_config_params { QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* * attributes. Array size = * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. */ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded * realm, 0 if unspecified. */ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, /* An array of 16 x unsigned 32-bit value; roaming consortium ids to * match, 0 if unspecified. */ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if * unspecified. */ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, /* Array of nested * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* * attributes. Array size = * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS. */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, /* Signed 8-bit value; threshold for considering this SSID as found, * required granularity for this threshold is 4 dBm to 8 dBm. */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD = 10, /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, /* Unsigned 8-bit value; auth bit field for matching WPA IE */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, /* Unsigned 8-bit to indicate ePNO type; * It takes values from qca_wlan_epno_type */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, /* Nested attribute to send the channel list */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, /* Unsigned 32-bit value; indicates the interval between PNO scan * cycles in msec. */ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, /* Unsigned 32-bit value, representing the PNO Request ID */ QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, /* keep last */ QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PNO_MAX = QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, }; /** * qca_wlan_vendor_acs_select_reason: This represents the different reasons why * the ACS has to be triggered. These values are used by * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON */ enum qca_wlan_vendor_acs_select_reason { /* Represents the reason that the ACS triggered during the AP start */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, /* Represents the reason that DFS found with the current channel */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, /* Represents the reason that LTE co-exist in the current band. */ QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, }; /** * qca_wlan_vendor_attr_external_acs_policy: Attribute values for * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the * external ACS policies to select the channels w.r.t. the PCL weights. * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and * their PCL weights.) * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to * select a channel with non-zero PCL weight. * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a * channel with non-zero PCL weight. * */ enum qca_wlan_vendor_attr_external_acs_policy { QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, }; /** * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. */ enum qca_wlan_vendor_channel_prop_flags { /* Bits 0, 1, 2, and 3 are reserved */ /* Turbo channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, /* CCK channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, /* OFDM channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, /* 2.4 GHz spectrum channel. */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, /* 5 GHz spectrum channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, /* Only passive scan allowed */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, /* Dynamic CCK-OFDM channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, /* GFSK channel (FHSS PHY) */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, /* Radar found on channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, /* 11a static turbo channel only */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, /* Half rate channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, /* Quarter rate channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, /* HT 20 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, /* HT 40 with extension channel above */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, /* HT 40 with extension channel below */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, /* HT 40 intolerant */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, /* VHT 20 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, /* VHT 40 with extension channel above */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, /* VHT 40 with extension channel below */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, /* VHT 80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, /* HT 40 intolerant mark bit for ACS use */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, /* Channel temporarily blocked due to noise */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, /* VHT 160 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, /* VHT 80+80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, /* HE 20 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, /* HE 40 with extension channel above */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, /* HE 40 with extension channel below */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, /* HE 40 intolerant */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31, }; /** * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. */ enum qca_wlan_vendor_channel_prop_flags_2 { /* HE 40 intolerant mark bit for ACS use */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, /* HE 80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, /* HE 160 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, /* HE 80+80 channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, }; /** * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for * each channel. This is used by * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. */ enum qca_wlan_vendor_channel_prop_flags_ext { /* Radar found on channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, /* DFS required on channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, /* DFS required on channel for 2nd band of 80+80 */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, /* If channel has been checked for DFS */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, /* Excluded in 802.11d */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, /* Channel Switch Announcement received on this channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, /* Ad-hoc is not allowed */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, /* Station only channel */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, /* DFS radar history for slave device (STA mode) */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, /* DFS CAC valid for slave device (STA mode) */ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, }; /** * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel * information. These attributes are sent as part of * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following * attributes correspond to a single channel. */ enum qca_wlan_vendor_external_acs_event_chan_info_attr { QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, /* A bitmask (u32) with flags specified in * enum qca_wlan_vendor_channel_prop_flags. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, /* A bitmask (u32) with flags specified in * enum qca_wlan_vendor_channel_prop_flags_ext. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, /* frequency in MHz (u32) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, /* maximum regulatory transmission power (u32) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, /* maximum transmission power (u32) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, /* minimum transmission power (u32) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, /* regulatory class id (u8) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, /* maximum antenna gain in (u8) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, /* VHT segment 0 (u8) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, /* VHT segment 1 (u8) */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, /* A bitmask (u32) with flags specified in * enum qca_wlan_vendor_channel_prop_flags_2. */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, /* keep last */ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, }; /** * qca_wlan_vendor_attr_pcl: Represents attributes for * preferred channel list (PCL). These attributes are sent as part of * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST. */ enum qca_wlan_vendor_attr_pcl { QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, /* Channel number (u8) */ QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, /* Channel weightage (u8) */ QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, /* Channel frequency (u32) in MHz */ QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3, /* Channel flags (u32) * bit 0 set: channel to be used for GO role, * bit 1 set: channel to be used on CLI role, * bit 2 set: channel must be considered for operating channel * selection & peer chosen operating channel should be * one of the channels with this flag set, * bit 3 set: channel should be excluded in GO negotiation */ QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4, }; /** * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by * host driver. */ enum qca_wlan_vendor_attr_external_acs_event { QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason. * This helps ACS module to understand why ACS needs to be started. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, /* Flag attribute to indicate if driver supports spectral scanning */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, /* Flag attribute to indicate if 11ac is offloaded to firmware */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, /* Flag attribute to indicate if driver provides additional channel * capability as part of scan operation */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, /* Flag attribute to indicate interface status is UP */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype * values. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, /* Channel width (u8). It takes one of enum nl80211_chan_width values. * This is the upper bound of channel width. ACS logic should try to get * a channel with the specified width and if not found, look for lower * values. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, /* This (u8) will hold values of one of enum nl80211_bands */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode * values */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, /* Array of (u32) supported frequency list among which ACS should choose * best frequency. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, /* Preferred channel list by the driver which will have array of nested * values as per enum qca_wlan_vendor_attr_pcl attribute. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, /* Array of nested attribute for each channel. It takes attr as defined * in enum qca_wlan_vendor_external_acs_event_chan_info_attr. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, /* External ACS policy such as PCL mandatory, PCL preferred, etc. * It uses values defined in enum * qca_wlan_vendor_attr_external_acs_policy. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, /* Reference RF Operating Parameter (RROP) availability information * (u16). It uses values defined in enum * qca_wlan_vendor_attr_rropavail_info. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, /* keep last */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, }; /** * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels * in priority order as decided after ACS operation in userspace. */ enum qca_wlan_vendor_attr_external_acs_channels { QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, /* Array of nested values for each channel with following attributes: * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, /* This (u8) will hold values of one of enum nl80211_bands */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, /* Primary channel (u8) */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, /* Secondary channel (u8) used for HT 40 MHz channels */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, /* VHT seg0 channel (u8) */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, /* VHT seg1 channel (u8) */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, /* Channel width (u8). Takes one of enum nl80211_chan_width values. */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, /* keep last */ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 }; enum qca_chip_power_save_failure_reason { /* Indicates if the reason for the failure is due to a protocol * layer/module. */ QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, /* Indicates if the reason for the failure is due to a hardware issue. */ QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, }; /** * qca_attr_chip_power_save_failure: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite * information leading to the power save failure. */ enum qca_attr_chip_power_save_failure { QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, /* Reason to cause the power save failure. * These reasons are represented by * enum qca_chip_power_save_failure_reason. */ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, /* keep last */ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, }; /** * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various * data types for which the stats have to get collected. */ enum qca_wlan_vendor_nud_stats_data_pkt_flags { QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0, QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1, QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2, QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3, QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4, /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get * to represent the stats of respective data type. */ QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5, QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6, QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7, }; enum qca_wlan_vendor_nud_stats_set_data_pkt_info { QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0, /* Represents the data packet type to be monitored (u32). * Host driver tracks the stats corresponding to each data frame * represented by these flags. * These data packets are represented by * enum qca_wlan_vendor_nud_stats_data_pkt_flags */ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1, /* Name corresponding to the DNS frame for which the respective DNS * stats have to get monitored (string). Max string length 255. */ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2, /* source port on which the respective proto stats have to get * collected (u32). */ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3, /* destination port on which the respective proto stats have to get * collected (u32). */ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4, /* IPv4 address for which the destined data packets have to be * monitored. (in network byte order), u32. */ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5, /* IPv6 address for which the destined data packets have to be * monitored. (in network byte order), 16 bytes array. */ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6, QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST, QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX = QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1, }; /** * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite * information to start/stop the NUD statistics collection. */ enum qca_attr_nud_stats_set { QCA_ATTR_NUD_STATS_SET_INVALID = 0, /* Flag to start/stop the NUD statistics collection. * Start - If included, Stop - If not included */ QCA_ATTR_NUD_STATS_SET_START = 1, /* IPv4 address of the default gateway (in network byte order), u32 */ QCA_ATTR_NUD_STATS_GW_IPV4 = 2, /* Represents the list of data packet types to be monitored. * Host driver tracks the stats corresponding to each data frame * represented by these flags. * These data packets are represented by * enum qca_wlan_vendor_nud_stats_set_data_pkt_info */ QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, /* keep last */ QCA_ATTR_NUD_STATS_SET_LAST, QCA_ATTR_NUD_STATS_SET_MAX = QCA_ATTR_NUD_STATS_SET_LAST - 1, }; enum qca_attr_nud_data_stats { QCA_ATTR_NUD_DATA_STATS_INVALID = 0, /* Data packet type for which the stats are collected (u32). * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags */ QCA_ATTR_NUD_STATS_PKT_TYPE = 1, /* Name corresponding to the DNS frame for which the respective DNS * stats are monitored (string). Max string length 255. */ QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2, /* source port on which the respective proto stats are collected (u32). */ QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3, /* destination port on which the respective proto stats are collected * (u32). */ QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4, /* IPv4 address for which the destined data packets have to be * monitored. (in network byte order), u32. */ QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5, /* IPv6 address for which the destined data packets have to be * monitored. (in network byte order), 16 bytes array. */ QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6, /* Data packet Request count received from netdev (u32). */ QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, /* Data packet Request count sent to lower MAC from upper MAC (u32). */ QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, /* Data packet Request count received by lower MAC from upper MAC * (u32) */ QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, /* Data packet Request count successfully transmitted by the device * (u32) */ QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, /* Data packet Response count received by lower MAC (u32) */ QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, /* Data packet Response count received by upper MAC (u32) */ QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, /* Data packet Response count delivered to netdev (u32) */ QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, /* Data Packet Response count that are dropped out of order (u32) */ QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, /* keep last */ QCA_ATTR_NUD_DATA_STATS_LAST, QCA_ATTR_NUD_DATA_STATS_MAX = QCA_ATTR_NUD_DATA_STATS_LAST - 1, }; /** * qca_attr_nud_stats_get: Attributes to vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite * NUD statistics collected when queried. */ enum qca_attr_nud_stats_get { QCA_ATTR_NUD_STATS_GET_INVALID = 0, /* ARP Request count from netdev (u32) */ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, /* ARP Request count sent to lower MAC from upper MAC (u32) */ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, /* ARP Request count received by lower MAC from upper MAC (u32) */ QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, /* ARP Request count successfully transmitted by the device (u32) */ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, /* ARP Response count received by lower MAC (u32) */ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, /* ARP Response count received by upper MAC (u32) */ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, /* ARP Response count delivered to netdev (u32) */ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, /* ARP Response count dropped due to out of order reception (u32) */ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, /* Flag indicating if the station's link to the AP is active. * Active Link - If included, Inactive link - If not included */ QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, /* Flag indicating if there is any duplicate address detected (DAD). * Yes - If detected, No - If not detected. */ QCA_ATTR_NUD_STATS_IS_DAD = 10, /* List of Data packet types for which the stats are requested. * This list does not carry ARP stats as they are done by the * above attributes. Represented by enum qca_attr_nud_data_stats. */ QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, /* keep last */ QCA_ATTR_NUD_STATS_GET_LAST, QCA_ATTR_NUD_STATS_GET_MAX = QCA_ATTR_NUD_STATS_GET_LAST - 1, }; enum qca_wlan_btm_candidate_status { QCA_STATUS_ACCEPT = 0, QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, QCA_STATUS_REJECT_LOW_RSSI = 4, QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, QCA_STATUS_REJECT_UNKNOWN = 6, }; enum qca_wlan_vendor_attr_btm_candidate_info { QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, /* 6-byte MAC address representing the BSSID of transition candidate */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status * returned by the driver. It says whether the BSSID provided in * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by * the driver, if not it specifies the reason for rejection. * Note that the user-space can overwrite the transition reject reason * codes provided by driver based on more information. */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, }; enum qca_attr_trace_level { QCA_ATTR_TRACE_LEVEL_INVALID = 0, /* * Nested array of the following attributes: * QCA_ATTR_TRACE_LEVEL_MODULE, * QCA_ATTR_TRACE_LEVEL_MASK. */ QCA_ATTR_TRACE_LEVEL_PARAM = 1, /* * Specific QCA host driver module. Please refer to the QCA host * driver implementation to get the specific module ID. */ QCA_ATTR_TRACE_LEVEL_MODULE = 2, /* Different trace level masks represented in the QCA host driver. */ QCA_ATTR_TRACE_LEVEL_MASK = 3, /* keep last */ QCA_ATTR_TRACE_LEVEL_AFTER_LAST, QCA_ATTR_TRACE_LEVEL_MAX = QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities */ enum qca_wlan_vendor_attr_get_he_capabilities { QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0, /* Whether HE capabilities is supported * (u8 attribute: 0 = not supported, 1 = supported) */ QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1, /* HE PHY capabilities, array of 3 u32 values */ QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2, /* HE MAC capabilities (u32 attribute) */ QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3, /* HE MCS map (u32 attribute) */ QCA_WLAN_VENDOR_ATTR_HE_MCS = 4, /* Number of SS (u32 attribute) */ QCA_WLAN_VENDOR_ATTR_NUM_SS = 5, /* RU count (u32 attribute) */ QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6, /* PPE threshold data, array of 8 u32 values */ QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX = QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters */ enum qca_wlan_vendor_attr_spectral_scan { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, /* Number of times the chip enters spectral scan mode before * deactivating spectral scans. When set to 0, chip will enter spectral * scan mode continuously. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, /* Spectral scan period. Period increment resolution is 256*Tclk, * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, /* Spectral scan priority. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, /* Number of FFT data points to compute. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, /* Enable targeted gain change before starting the spectral scan FFT. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, /* Restart a queued spectral scan. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, /* Noise floor reference number for the calculation of bin power. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, /* Disallow spectral scan triggers after TX/RX packets by setting * this delay value to roughly SIFS time period or greater. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, /* Number of strong bins (inclusive) per sub-channel, below * which a signal is declared a narrow band tone. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, /* Specify the threshold over which a bin is declared strong (for * scan bandwidth analysis). u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, /* Spectral scan report mode. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, /* RSSI report mode, if the ADC RSSI is below * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, * then FFTs will not trigger, but timestamps and summaries get * reported. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, /* ADC RSSI must be greater than or equal to this threshold (signed dB) * to ensure spectral scan reporting with normal error code. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, /* Format of frequency bin magnitude for spectral scan triggered FFTs: * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, /* Format of FFT report to software for spectral scan triggered FFTs. * 0: No FFT report (only spectral scan summary report) * 1: 2-dword summary of metrics for each completed FFT + spectral scan * report * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled * bins (in-band) per FFT + spectral scan summary report * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled * bins (all) per FFT + spectral scan summary report * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, /* Number of LSBs to shift out in order to scale the FFT bins. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes * in dBm power. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, /* Per chain enable mask to select input ADC for search FFT. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, /* An unsigned 64-bit integer provided by host driver to identify the * spectral scan request. This attribute is included in the scan * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START * and used as an attribute in * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the * specific scan to be stopped. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, /* Skip interval for FFT reports. u32 attribute */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, /* Set to report only one set of FFT results. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, /* Debug level for spectral module in driver. * 0 : Verbosity level 0 * 1 : Verbosity level 1 * 2 : Verbosity level 2 * 3 : Matched filterID display * 4 : One time dump of FFT report * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, /* Type of spectral scan request. u32 attribute. * It uses values defined in enum * qca_wlan_vendor_attr_spectral_scan_request_type. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. */ enum qca_wlan_vendor_attr_spectral_diag_stats { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, /* Number of spectral TLV signature mismatches. * u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, /* Number of spectral phyerror events with insufficient length when * parsing for secondary 80 search FFT report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, /* Number of spectral phyerror events without secondary 80 * search FFT report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, /* Number of spectral phyerror events with vht operation segment 1 id * mismatches in search fft report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, /* Number of spectral phyerror events with vht operation segment 2 id * mismatches in search fft report. u64 attribute. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. */ enum qca_wlan_vendor_attr_spectral_cap { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, /* Flag attribute to indicate phydiag capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, /* Flag attribute to indicate radar detection capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, /* Flag attribute to indicate spectral capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, /* Flag attribute to indicate advanced spectral capability */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, /* Spectral hardware generation. u32 attribute. * It uses values defined in enum * qca_wlan_vendor_spectral_scan_cap_hw_gen. */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. */ enum qca_wlan_vendor_attr_spectral_scan_status { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, /* Flag attribute to indicate whether spectral scan is enabled */ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, /* Flag attribute to indicate whether spectral scan is in progress*/ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, }; /** * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the * spectral scan request types. * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to * set the spectral parameters and start scan. * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to * only set the spectral parameters. * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to * only start the spectral scan. */ enum qca_wlan_vendor_attr_spectral_scan_request_type { QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, }; /** * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the * spectral hardware generation. * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 */ enum qca_wlan_vendor_spectral_scan_cap_hw_gen { QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, }; enum qca_wlan_vendor_tos { QCA_WLAN_VENDOR_TOS_BK = 0, QCA_WLAN_VENDOR_TOS_BE = 1, QCA_WLAN_VENDOR_TOS_VI = 2, QCA_WLAN_VENDOR_TOS_VO = 3, }; /** * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. */ enum qca_wlan_vendor_attr_active_tos { QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, /* Type Of Service - Represented by qca_wlan_vendor_tos */ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, /* Flag attribute representing the start (attribute included) or stop * (attribute not included) of the respective TOS. */ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, }; enum qca_wlan_vendor_hang_reason { /* Unspecified reason */ QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, /* No Map for the MAC entry for the received frame */ QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, /* Peer deletion timeout happened */ QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, /* Peer unmap timeout */ QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, /* Scan request timed out */ QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, /* Consecutive Scan attempt failures */ QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, /* Unable to get the message buffer */ QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, /* Current command processing is timedout */ QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, /* Timeout for an ACK from FW for suspend request */ QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, /* Timeout for an ACK from FW for resume request */ QCA_WLAN_HANG_RESUME_TIMEOUT = 9, /* Transmission timeout for consecutive data frames */ QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, /* Timeout for the TX completion status of data frame */ QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, /* DXE failure for TX/RX, DXE resource unavailability */ QCA_WLAN_HANG_DXE_FAILURE = 12, /* WMI pending commands exceed the maximum count */ QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, }; /** * enum qca_wlan_vendor_attr_hang - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_HANG. */ enum qca_wlan_vendor_attr_hang { QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, /* Reason for the hang - u32 attribute with a value from enum * qca_wlan_vendor_hang_reason. */ QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_HANG_MAX = QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_flush_pending - Attributes for * flushing pending traffic in firmware. * * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address. * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK, * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to * flush packets with access category. */ enum qca_wlan_vendor_attr_flush_pending { QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0, QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1, QCA_WLAN_VENDOR_ATTR_AC = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX = QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative * RF Operating Parameter (RROP) information is available, and if so, at which * point in the application-driver interaction sequence it can be retrieved by * the application from the driver. This point may vary by architecture and * other factors. This is a u16 value. */ enum qca_wlan_vendor_attr_rropavail_info { /* RROP information is unavailable. */ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, /* RROP information is available and the application can retrieve the * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS * event from the driver. */ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, /* RROP information is available only after a vendor specific scan * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has * successfully completed. The application can retrieve the information * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from * the driver. */ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, }; /** * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific * Representative RF Operating Parameter (RROP) information. It is sent for the * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is * intended for use by external Auto Channel Selection applications. It provides * guidance values for some RF parameters that are used by the system during * operation. These values could vary by channel, band, radio, and so on. */ enum qca_wlan_vendor_attr_rrop_info { QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, /* Representative Tx Power List (RTPL) which has an array of nested * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. */ QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list * entry instances in the Representative Tx Power List (RTPL). It provides * simplified power values intended for helping external Auto channel Selection * applications compare potential Tx power performance between channels, other * operating conditions remaining identical. These values are not necessarily * the actual Tx power values that will be used by the system. They are also not * necessarily the max or average values that will be used. Instead, they are * relative, summarized keys for algorithmic use computed by the driver or * underlying firmware considering a number of vendor specific factors. */ enum qca_wlan_vendor_attr_rtplinst { QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, /* Primary channel number (u8) */ QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, /* Representative Tx power in dBm (s32) with emphasis on throughput. */ QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, /* Representative Tx power in dBm (s32) with emphasis on range. */ QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_config_latency_level - Level for * wlan latency module. * * There will be various of Wi-Fi functionality like scan/roaming/adaptive * power saving which would causing data exchange out of service, this * would be a big impact on latency. For latency sensitive applications over * Wi-Fi are intolerant to such operations and thus would configure them * to meet their respective needs. It is well understood by such applications * that altering the default behavior would degrade the Wi-Fi functionality * w.r.t the above pointed WLAN operations. * * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: * Default WLAN operation level which throughput orientated. * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE: * Use moderate level to improve latency by limit scan duration. * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: * Use low latency level to benifit application like concurrent * downloading or video streaming via constraint scan/adaptive PS. * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: * Use ultra low latency level to benefit for gaming/voice * application via constraint scan/roaming/adaptive PS. */ enum qca_wlan_vendor_attr_config_latency_level { QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. */ enum qca_wlan_vendor_attr_mac { QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, /* MAC mode info list which has an array of nested values as * per attributes in enum qca_wlan_vendor_attr_mac_mode_info. */ QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAC_MAX = QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected * Wi-Fi netdev interface on a respective MAC. * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. */ enum qca_wlan_vendor_attr_mac_iface_info { QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, /* Wi-Fi netdev's interface index (u32) */ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. */ enum qca_wlan_vendor_attr_mac_info { QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, /* Hardware MAC ID associated for the MAC (u32) */ QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, /* Band supported by the MAC at a given point. * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum * nl80211_band. */ QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, /* Refers to list of WLAN netdev interfaces associated with this MAC. * Represented by enum qca_wlan_vendor_attr_mac_iface_info. */ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, /* keep last */ QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET. */ enum qca_wlan_vendor_attr_get_logger_features { QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, /* Unsigned 32-bit enum value of wifi_logger_supported_features */ QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, }; /** * enum wifi_logger_supported_features - Values for supported logger features */ enum wifi_logger_supported_features { WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)), WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)), WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)), WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)), WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)), WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)), WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)), WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)), WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)), }; /** * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get * capabilities features */ enum qca_wlan_tdls_caps_features_supported { WIFI_TDLS_SUPPORT = (1 << (0)), WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)), WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2)) }; /** * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES. */ enum qca_wlan_vendor_attr_tdls_get_capabilities { QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, /* Indicates the max concurrent sessions */ /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS, /* Indicates the support for features */ /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported */ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED, /* keep last */ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, }; /** * enum qca_wlan_offloaded_packets_sending_control - Offload packets control * command used as value for the attribute * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL. */ enum qca_wlan_offloaded_packets_sending_control { QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0, QCA_WLAN_OFFLOADED_PACKETS_SENDING_START, QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP }; /** * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS. */ enum qca_wlan_vendor_attr_offloaded_packets { QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, /* Takes valid value from the enum * qca_wlan_offloaded_packets_sending_control * Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, /* array of u8 len: Max packet size */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, /* 6-byte MAC address used to represent source MAC address */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, /* 6-byte MAC address used to represent destination MAC address */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, /* Unsigned 32-bit value, in milli seconds */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, /* keep last */ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, }; /** * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL. */ enum qca_wlan_rssi_monitoring_control { QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, QCA_WLAN_RSSI_MONITORING_START, QCA_WLAN_RSSI_MONITORING_STOP, }; /** * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI. */ enum qca_wlan_vendor_attr_rssi_monitoring { QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, /* Takes valid value from the enum * qca_wlan_rssi_monitoring_control * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, /* Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, /* Signed 8-bit value in dBm */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, /* Signed 8-bit value in dBm */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, /* attributes to be used/received in callback */ /* 6-byte MAC address used to represent current BSSID MAC address */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, /* Signed 8-bit value indicating the current RSSI */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, /* keep last */ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_NDP. */ enum qca_wlan_vendor_attr_ndp_params { QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, /* Unsigned 32-bit value * enum of sub commands values in qca_wlan_ndp_sub_cmd */ QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD, /* Unsigned 16-bit value */ QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID, /* NL attributes for data used NDP SUB cmds */ /* Unsigned 32-bit value indicating a service info */ QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID, /* Unsigned 32-bit value; channel frequency in MHz */ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL, /* Interface Discovery MAC address. An array of 6 Unsigned int8 */ QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR, /* Interface name on which NDP is being created */ QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR, /* Unsigned 32-bit value for security */ /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */ QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY, /* Unsigned 32-bit value for QoS */ QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS, /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */ QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO, /* Unsigned 32-bit value for NDP instance Id */ QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID, /* Array of instance Ids */ QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY, /* Unsigned 32-bit value for initiator/responder NDP response code * accept/reject */ QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE, /* NDI MAC address. An array of 6 Unsigned int8 */ QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR, /* Unsigned 32-bit value errors types returned by driver * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy * NanStatusType includes these values. */ QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE, /* Unsigned 32-bit value error values returned by driver * The nan_i.h in AOSP project platform/hardware/qcom/wlan * NanInternalStatusType includes these values. */ QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE, /* Unsigned 32-bit value for Channel setup configuration * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy * NanDataPathChannelCfg includes these values. */ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG, /* Unsigned 32-bit value for Cipher Suite Shared Key Type */ QCA_WLAN_VENDOR_ATTR_NDP_CSID, /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */ QCA_WLAN_VENDOR_ATTR_NDP_PMK, /* Security Context Identifier that contains the PMKID * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes */ QCA_WLAN_VENDOR_ATTR_NDP_SCID, /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */ QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE, /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */ QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME, /* Unsigned 32-bit bitmap indicating schedule update * BIT_0: NSS Update * BIT_1: Channel list update */ QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON, /* Unsigned 32-bit value for NSS */ QCA_WLAN_VENDOR_ATTR_NDP_NSS, /* Unsigned 32-bit value for NUMBER NDP CHANNEL */ QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS, /* Unsigned 32-bit value for CHANNEL BANDWIDTH * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH, /* Array of channel/band width */ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO, /* IPv6 address used by NDP (in network byte order), 16 bytes array. * This attribute is used and optional for ndp request, ndp response, * ndp indication, and ndp confirm. */ QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, /* Unsigned 16-bit value indicating transport port used by NDP. * This attribute is used and optional for ndp response, ndp indication, * and ndp confirm. */ QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, /* Unsigned 8-bit value indicating protocol used by NDP and assigned by * the Internet Assigned Numbers Authority (IANA) as per: * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml * This attribute is used and optional for ndp response, ndp indication, * and ndp confirm. */ QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, /* Unsigned 8-bit value indicating if NDP remote peer supports NAN NDPE. * 1:support 0:not support */ QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT = 30, /* keep last */ QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, }; enum qca_wlan_ndp_sub_cmd { QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, /* Command to create a NAN data path interface */ QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, /* Command to delete a NAN data path interface */ QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, /* Command to initiate a NAN data path session */ QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, /* Command to notify if the NAN data path session was sent */ QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, /* Command to respond to NAN data path session */ QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, /* Command to notify on the responder about the response */ QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, /* Command to initiate a NAN data path end */ QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, /* Command to notify the if end request was sent */ QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, /* Command to notify the peer about the end request */ QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, /* Command to confirm the NAN data path session is complete */ QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, /* Command to indicate the peer about the end request being received */ QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, /* Command to indicate the peer of schedule update */ QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 }; /** * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD. */ enum qca_wlan_vendor_attr_nd_offload { QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, /* Flag to set Neighbour Discovery offload */ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, /* Keep last */ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, }; /** * enum packet_filter_sub_cmd - Packet filter sub commands */ enum packet_filter_sub_cmd { /** * Write packet filter program and/or data. The driver/firmware should * disable APF before writing into local buffer and re-enable APF after * writing is done. */ QCA_WLAN_SET_PACKET_FILTER = 1, /* Get packet filter feature capabilities from driver */ QCA_WLAN_GET_PACKET_FILTER = 2, /** * Write packet filter program and/or data. User space will send the * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over * enable/disable is given to user space with this command. Also, * user space sends the length of program portion in the buffer within * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH. */ QCA_WLAN_WRITE_PACKET_FILTER = 3, /* Read packet filter program and/or data */ QCA_WLAN_READ_PACKET_FILTER = 4, /* Enable APF feature */ QCA_WLAN_ENABLE_PACKET_FILTER = 5, /* Disable APF feature */ QCA_WLAN_DISABLE_PACKET_FILTER = 6, }; /** * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER. */ enum qca_wlan_vendor_attr_packet_filter { QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD, /* Unsigned 32-bit value indicating the packet filter version */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, /* Unsigned 32-bit value indicating the packet filter id */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, /** * Unsigned 32-bit value indicating the packet filter size including * program + data. */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, /* Unsigned 32-bit value indicating the packet filter current offset */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, /* Program and/or data in bytes */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, /* Unsigned 32-bit value of the length of the program section in packet * filter buffer. */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH = 7, /* keep last */ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE. */ enum qca_wlan_vendor_drv_info { QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, /* Maximum Message size info between firmware & HOST * Unsigned 32-bit value */ QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, /* keep last */ QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS. */ enum qca_wlan_vendor_attr_wake_stats { QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0, /* Unsigned 32-bit value indicating the total count of wake event */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE, /* Array of individual wake count, each index representing wake reason */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR, /* Unsigned 32-bit value representing wake count array */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ, /* Unsigned 32-bit total wake count value of driver/fw */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE, /* Array of wake stats of driver/fw */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR, /* Unsigned 32-bit total wake count value of driver/fw */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ, /* Unsigned 32-bit total wake count value of packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE, /* Unsigned 32-bit wake count value unicast packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT, /* Unsigned 32-bit wake count value multicast packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value broadcast packets received */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT, /* Unsigned 32-bit wake count value of ICMP packets */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT, /* Unsigned 32-bit wake count value of ICMP6 packets */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT, /* Unsigned 32-bit value ICMP6 router advertisement */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA, /* Unsigned 32-bit value ICMP6 neighbor advertisement */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA, /* Unsigned 32-bit value ICMP6 neighbor solicitation */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS, /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value of receive side multicast */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT, /* Unsigned 32-bit wake count value of a given RSSI breach */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT, /* Unsigned 32-bit wake count value of low RSSI */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT, /* Unsigned 32-bit value GSCAN count */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT, /* Unsigned 32-bit value PNO complete count */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT, /* Unsigned 32-bit value PNO match count */ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT, /* keep last */ QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set * cmd value. Used for NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. */ enum qca_wlan_vendor_attr_thermal_cmd { QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0, /* The value of command, driver will implement different operations * according to this value. It uses values defined in * enum qca_wlan_vendor_attr_thermal_cmd_type. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1 }; /** * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the * thermal command types sent to driver. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to * get thermal shutdown configuration parameters for display. Parameters * responded from driver are defined in * enum qca_wlan_vendor_attr_get_thermal_params_rsp. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to * get temperature. Host should respond with a temperature data. It is defined * in enum qca_wlan_vendor_attr_thermal_get_temperature. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal * suspend action. * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal * resume action. */ enum qca_wlan_vendor_attr_thermal_cmd_type { QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND, QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME, }; /** * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes * to get chip temperature by user. * enum values are used for NL attributes for data used by * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. */ enum qca_wlan_vendor_attr_thermal_get_temperature { QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0, /* Temperature value (degree Celsius) from driver. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes * to get configuration parameters of thermal shutdown feature. Enum values are * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. */ enum qca_wlan_vendor_attr_get_thermal_params_rsp { QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0, /* Indicate if the thermal shutdown feature is enabled. * NLA_FLAG attribute. */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN, /* Indicate if the auto mode is enabled. * Enable: Driver triggers the suspend/resume action. * Disable: User space triggers the suspend/resume action. * NLA_FLAG attribute. */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN, /* Thermal resume threshold (degree Celsius). Issue the resume command * if the temperature value is lower than this threshold. * u16 attribute. */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH, /* Thermal warning threshold (degree Celsius). FW reports temperature * to driver if it's higher than this threshold. * u16 attribute. */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH, /* Thermal suspend threshold (degree Celsius). Issue the suspend command * if the temperature value is higher than this threshold. * u16 attribute. */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH, /* FW reports temperature data periodically at this interval (ms). * u16 attribute. */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE, /* keep last */ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX = QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to * report thermal events from driver to user space. * enum values are used for NL attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command. */ enum qca_wlan_vendor_attr_thermal_event { QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0, /* Temperature value (degree Celsius) from driver. * u32 attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE, /* Indication of resume completion from power save mode. * NLA_FLAG attribute. */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE, /* keep last */ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX = QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1, }; /** * enum he_fragmentation_val - HE fragmentation support values * Indicates level of dynamic fragmentation that is supported by * a STA as a recipient. * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2 * (HE MAC Capabilities Information field) and are used in HE Capabilities * element to advertise the support. These values are validated in the driver * to check the device capability and advertised in the HE Capabilities * element. These values are used to configure testbed device to allow the * advertised hardware capabilities to be downgraded for testing purposes. * * @HE_FRAG_DISABLE: no support for dynamic fragmentation * @HE_FRAG_LEVEL1: support for dynamic fragments that are * contained within an MPDU or S-MPDU, no support for dynamic fragments * within an A-MPDU that is not an S-MPDU. * @HE_FRAG_LEVEL2: support for dynamic fragments that are * contained within an MPDU or S-MPDU and support for up to one dynamic * fragment for each MSDU, each A-MSDU if supported by the recipient, and * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an * MPDU or S-MPDU. * @HE_FRAG_LEVEL3: support for dynamic fragments that are * contained within an MPDU or S-MPDU and support for multiple dynamic * fragments for each MSDU and for each A-MSDU if supported by the * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. */ enum he_fragmentation_val { HE_FRAG_DISABLE, HE_FRAG_LEVEL1, HE_FRAG_LEVEL2, HE_FRAG_LEVEL3, }; /** * enum he_mcs_config - HE MCS support configuration * * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. * These values are used in driver to configure the HE MCS map to advertise * Tx/Rx MCS map in HE capability and these values are applied for all the * streams supported by the device. To configure MCS for different bandwidths, * vendor command needs to be sent using this attribute with appropriate value. * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11 * send this command using HE MCS config attribute with value HE_160_MCS0_11. * These values are used to configure testbed device to allow the advertised * hardware capabilities to be downgraded for testing purposes. The enum values * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map. * These values are validated in the driver before setting the MCS map and * driver returns error if the input is other than these enum values. * * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11 */ enum he_mcs_config { HE_80_MCS0_7 = 0, HE_80_MCS0_9 = 1, HE_80_MCS0_11 = 2, HE_160_MCS0_7 = 4, HE_160_MCS0_9 = 5, HE_160_MCS0_11 = 6, HE_80P80_MCS0_7 = 8, HE_80P80_MCS0_9 = 9, HE_80P80_MCS0_11 = 10, }; /** * enum qca_wlan_ba_session_config - BA session configuration * * Indicates the configuration values for BA session configuration attribute. * * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. */ enum qca_wlan_ba_session_config { QCA_WLAN_ADD_BA = 1, QCA_WLAN_DELETE_BA = 2, }; /** * enum qca_wlan_ac_type - Access category type * * Indicates the access category type value. * * @QCA_WLAN_AC_BE: BE access category * @QCA_WLAN_AC_BK: BK access category * @QCA_WLAN_AC_VI: VI access category * @QCA_WLAN_AC_VO: VO access category * @QCA_WLAN_AC_ALL: All ACs */ enum qca_wlan_ac_type { QCA_WLAN_AC_BE = 0, QCA_WLAN_AC_BK = 1, QCA_WLAN_AC_VI = 2, QCA_WLAN_AC_VO = 3, QCA_WLAN_AC_ALL = 4, }; /** * enum qca_wlan_he_ltf_cfg - HE LTF configuration * * Indicates the HE LTF configuration value. * * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF, * based on the GI setting * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF */ enum qca_wlan_he_ltf_cfg { QCA_WLAN_HE_LTF_AUTO = 0, QCA_WLAN_HE_LTF_1X = 1, QCA_WLAN_HE_LTF_2X = 2, QCA_WLAN_HE_LTF_4X = 3, }; /** * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration * * Indicates the HE trigger frame MAC padding duration value. * * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to * process the trigger frame. * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for * trigger frame. * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for * trigger frame. */ enum qca_wlan_he_mac_padding_dur { QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, }; /** * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration * * Indicates the HE Operating mode control channel width setting value. * * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz */ enum qca_wlan_he_om_ctrl_ch_bw { QCA_WLAN_HE_OM_CTRL_BW_20M = 0, QCA_WLAN_HE_OM_CTRL_BW_40M = 1, QCA_WLAN_HE_OM_CTRL_BW_80M = 2, QCA_WLAN_HE_OM_CTRL_BW_160M = 3, }; /* Attributes for data used by * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION */ enum qca_wlan_vendor_attr_wifi_test_config { QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, /* 8-bit unsigned value to configure the driver to enable/disable * WMM feature. This attribute is used to configure testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, /* 8-bit unsigned value to configure the driver to accept/reject * the addba request from peer. This attribute is used to configure * the testbed device. * 1-accept addba, 0-reject addba */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, /* 8-bit unsigned value to configure the driver to send or not to * send the addba request to peer. * This attribute is used to configure the testbed device. * 1-send addba, 0-do not send addba */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, /* 8-bit unsigned value to indicate the HE fragmentation support. * Uses enum he_fragmentation_val values. * This attribute is used to configure the testbed device to * allow the advertised hardware capabilities to be downgraded * for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, /* 8-bit unsigned value to indicate the HE MCS support. * Uses enum he_mcs_config values. * This attribute is used to configure the testbed device to * allow the advertised hardware capabilities to be downgraded * for testing purposes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, /* 8-bit unsigned value to configure the driver to allow or not to * allow the connection with WEP/TKIP in HT/VHT/HE modes. * This attribute is used to configure the testbed device. * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, /* 8-bit unsigned value to configure the driver to add a * new BA session or delete the existing BA session for * given TID. ADDBA command uses the buffer size and TID * configuration if user specifies the values else default * value for buffer size is used for all TIDs if the TID * also not specified. For DEL_BA command TID value is * required to process the command. * Uses enum qca_wlan_ba_session_config values. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, /* 16-bit unsigned value to configure the buffer size in addba * request and response frames. * This attribute is used to configure the testbed device. * The range of the value is 0 to 256. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, /* 8-bit unsigned value to configure the buffer size in addba * request and response frames. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, /* 8-bit unsigned value to configure the no ack policy. * To configure no ack policy, access category value is * required to process the command. * This attribute is used to configure the testbed device. * 1 - enable no ack, 0 - disable no ack. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, /* 8-bit unsigned value to configure the AC for no ack policy * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_ac_type values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, /* 8-bit unsigned value to configure the HE LTF * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_he_ltf_cfg values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, /* 8-bit unsigned value to configure the tx beamformee. * This attribute is used to configure the testbed device. * 1-enable, 0-disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, /* 8-bit unsigned value to configure the tx beamformee number * of space-time streams. * This attribute is used to configure the testbed device. * The range of the value is 0 to 8. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, /* 8-bit unsigned value to configure the MU EDCA params for given AC * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_ac_type values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC * To configure MU EDCA AIFSN value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, /* 8-bit unsigned value to configure the MU EDCA ECW min value for * given AC. * To configure MU EDCA ECW min value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, /* 8-bit unsigned value to configure the MU EDCA ECW max value for * given AC. * To configure MU EDCA ECW max value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, /* 8-bit unsigned value to configure the MU EDCA timer for given AC * To configure MU EDCA timer value, MU EDCA access category value * is required to process the command. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, /* 8-bit unsigned value to configure the HE trigger frame MAC padding * duration. * This attribute is used to configure the testbed device. * Uses the enum qca_wlan_he_mac_padding_dur values. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, /* 8-bit unsigned value to override the MU EDCA params to defaults * regardless of the AP beacon MU EDCA params. If it is enabled use * the default values else use the MU EDCA params from AP beacon. * This attribute is used to configure the testbed device. * 1-enable, 0-disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, /* 8-bit unsigned value to configure the support for receiving * an MPDU that contains an operating mode control subfield. * This attribute is used to configure the testbed device. * 1-enable, 0-disable. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, /* Nested attribute values required to setup the TWT session. * enum qca_wlan_vendor_attr_twt_setup provides the necessary * information to set up the session. It contains broadcast flags, * set_up flags, trigger value, flow type, flow ID, wake interval * exponent, protection, target wake time, wake duration, wake interval * mantissa. These nested attributes are used to setup a host triggered * TWT session. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, /* This nested attribute is used to terminate the current TWT session. * It does not currently carry any attributes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, /* This nested attribute is used to suspend the current TWT session. * It does not currently carry any attributes. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, /* Nested attribute values to indicate the request for resume. * This attribute is used to resume the TWT session. * enum qca_wlan_vendor_attr_twt_resume provides the necessary * parameters required to resume the TWT session. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, /* 8-bit unsigned value to set the HE operating mode control * (OM CTRL) Channel Width subfield. * The Channel Width subfield indicates the operating channel width * supported by the STA for both reception and transmission. * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. * This setting is cleared with the * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG * flag attribute to reset defaults. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, /* 8-bit unsigned value to configure the number of spatial * streams in HE operating mode control field. * This setting is cleared with the * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG * flag attribute to reset defaults. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, /* Flag attribute to configure the UL MU disable bit in * HE operating mode control field. * This setting is cleared with the * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG * flag attribute to reset defaults. * This attribute is used to configure the testbed device. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, /* Flag attribute to clear the previously set HE operating mode * control field configuration. * This attribute is used to configure the testbed device to reset * defaults to clear any previously set HE operating mode control * field configuration. */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, /* 8-bit unsigned value to configure HE single user PPDU * transmission. By default this setting is disabled and it * is disabled in the reset defaults of the device configuration. * This attribute is used to configure the testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, /* 8-bit unsigned value to configure action frame transmission * in HE trigger based PPDU transmission. * By default this setting is disabled and it is disabled in * the reset defaults of the device configuration. * This attribute is used to configure the testbed device. * 1-enable, 0-disable */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, /* keep last */ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. * The user can add/delete the filter by specifying the BSSID/STA MAC address in * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the * statistics of an unassociated station by specifying the MAC address in * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get * the statistics of all unassociated stations by specifying the Broadcast MAC * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with * above procedure. In the response, driver shall specify statistics * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS. */ enum qca_wlan_vendor_attr_bss_filter { QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID = 0, QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR = 1, /* Other BSS filter type, unsigned 8 bit value. One of the values * in enum qca_wlan_vendor_bss_filter_type. */ QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE = 2, /* Other BSS filter action, unsigned 8 bit value. One of the values * in enum qca_wlan_vendor_bss_filter_action. */ QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION = 3, /* Array of nested attributes where each entry is the statistics * information of the specified station that belong to another BSS. * Attributes for each entry are taken from enum * qca_wlan_vendor_bss_filter_sta_stats. * Other BSS station configured in * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA. * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET. */ QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX = QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_bss_filter_type - Type of * filter used in other BSS filter operations. Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. * * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter */ enum qca_wlan_vendor_bss_filter_type { QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID, QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA, }; /** * enum qca_wlan_vendor_bss_filter_action - Type of * action in other BSS filter operations. Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. * * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics */ enum qca_wlan_vendor_bss_filter_action { QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD, QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL, QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET, }; /** * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for * the statistics of a specific unassociated station belonging to another BSS. * The statistics provides information of the unassociated station * filtered by other BSS operation - such as MAC, signal value. * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. * * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station. * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength * of the station. Unsigned 8 bit number containing RSSI. * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host * driver for the last received RSSI. Unsigned 64 bit number containing * nanoseconds from the boottime. */ enum qca_wlan_vendor_bss_filter_sta_stats { QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID = 0, QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC = 1, QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI = 2, QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS = 3, /* keep last */ QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST, QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX = QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST - 1 }; /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. */ enum qca_wlan_nan_ext_subcmd_type { /* Subcmd of type NAN Enable Request */ QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, /* Subcmd of type NAN Disable Request */ QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, }; /** * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. */ enum qca_wlan_vendor_attr_nan_params { QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, /* Carries NAN command for firmware component. Every vendor command * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a * payload containing the NAN command. NLA_BINARY attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, /* Indicates the type of NAN command sent with * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type * describes the possible range of values. This attribute is mandatory * if the command being issued is either * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz * band. This attribute is mandatory when command type is * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz * band. This attribute is optional and should be included when command * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. */ QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, /* keep last */ QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 }; /** * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for * TWT (Target Wake Time) setup request. These attributes are sent as part of * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. * Disable (flag attribute not present) - Individual TWT * Enable (flag attribute present) - Broadcast TWT. * Individual means the session is between the STA and the AP. * This session is established using a separate negotiation between * STA and AP. * Broadcast means the session is across multiple STAs and an AP. The * configuration parameters are announced in Beacon frames by the AP. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to * specify the TWT request type * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute * Enable (flag attribute present) - TWT with trigger support. * Disable (flag attribute not present) - TWT without trigger support. * Trigger means the AP will send the trigger frame to allow STA to send data. * Without trigger, the STA will wait for the MU EDCA timer before * transmitting the data. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) * 0 - Announced TWT - In this mode, STA may skip few service periods to * save more power. If STA wants to wake up, it will send a PS-POLL/QoS * NULL frame to AP. * 1 - Unannounced TWT - The STA will wakeup during every SP. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) * Flow ID is the unique identifier for each TWT session. * Currently this is not required and dialog ID will be set to zero. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) * This attribute (exp) is used along with the mantissa to derive the * wake interval using the following formula: * pow(2,exp) = wake_intvl_us/wake_intvl_mantis * Wake interval is the interval between 2 successive SP. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute * Enable (flag attribute present) - Protection required. * Disable (flag attribute not present) - Protection not required. * If protection is enabled, then the AP will use protection * mechanism using RTS/CTS to self to reserve the airtime. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) * This attribute is used as the SP offset which is the offset from * TSF after which the wake happens. The units are in microseconds. If * this attribute is not provided, then the value will be set to zero. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) * This is the duration of the service period. The units are in TU. * * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) * This attribute is used to configure wake interval mantissa. * The units are in TU. */ enum qca_wlan_vendor_attr_twt_setup { QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for * TWT (Target Wake Time) resume request. These attributes are sent as part of * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. * * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) * This attribute is used as the SP offset which is the offset from * TSF after which the wake happens. The units are in microseconds. * If this attribute is not provided, then the value will be set to * zero. * * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) * This attribute represents the next TWT subfield size. */ enum qca_wlan_vendor_attr_twt_resume { QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) * Represents the setup type being requested for TWT. * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT * parameters but relying on AP to fill the parameters during the negotiation. * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested * values which the AP may accept or AP may provide alternative parameters * which the STA may accept. * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any * alternate parameters than the requested ones. */ enum qca_wlan_vendor_twt_setup_req_type { QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, }; /** * enum qca_wlan_roam_scan_event_type - Type of roam scan event * * Indicates the type of roam scan event sent by firmware/driver. * * @QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT: Roam scan trigger event type. * @QCA_WLAN_ROAM_SCAN_STOP_EVENT: Roam scan stopped event type. */ enum qca_wlan_roam_scan_event_type { QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT = 0, QCA_WLAN_ROAM_SCAN_STOP_EVENT = 1, }; /** * enum qca_wlan_roam_scan_trigger_reason - Roam scan trigger reason * * Indicates the reason for triggering roam scan by firmware/driver. * * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI: Due to low RSSI of current AP. * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER: Due to high packet error rate. */ enum qca_wlan_roam_scan_trigger_reason { QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI = 0, QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER = 1, }; /** * enum qca_wlan_vendor_attr_roam_scan - Vendor subcmd attributes to report * roam scan related details from driver/firmware to user space. enum values * are used for NL attributes sent with * %QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT sub command. */ enum qca_wlan_vendor_attr_roam_scan { QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_INVALID = 0, /* Encapsulates type of roam scan event being reported. enum * qca_wlan_roam_scan_event_type describes the possible range of * values. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_EVENT_TYPE = 1, /* Encapsulates reason for triggering roam scan. enum * qca_wlan_roam_scan_trigger_reason describes the possible range of * values. u32 attribute. */ QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_TRIGGER_REASON = 2, /* keep last */ QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_MAX = QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. */ enum qca_wlan_vendor_cfr_method { /* CFR method using QOS Null frame */ QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0, }; /** * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer * Channel Frequency Response capture parameters and enable periodic CFR * capture. */ enum qca_wlan_vendor_peer_cfr_capture_attr { QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0, /* 6-byte MAC address of the peer. * This attribute is mandatory. */ QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1, /* Enable peer CFR Capture, flag attribute. * This attribute is mandatory to enable peer CFR capture. * If this attribute is not present, peer CFR capture is disabled. */ QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2, /* BW of measurement, attribute uses the values in enum nl80211_chan_width * Supported values: 20, 40, 80, 80+80, 160. * Note that all targets may not support all bandwidths. * u8 attribute. This attribute is mandatory if attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. */ QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3, /* Periodicity of CFR measurement in msec. * Periodicity should be a multiple of Base timer. * Current Base timer value supported is 10 msecs (default). * 0 for one shot capture. u32 attribute. * This attribute is mandatory if attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. */ QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4, /* Method used to capture Channel Frequency Response. * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method. * u8 attribute. This attribute is mandatory if attribute * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. */ QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5, /* Enable periodic CFR capture, flag attribute. * This attribute is mandatory to enable Periodic CFR capture. * If this attribute is not present, periodic CFR capture is disabled. */ QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6, /* Keep last */ QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX = QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1, }; /** * enum qca_wlan_throughput_level - Current throughput level * * Indicates the current level of throughput calculated by the driver. The * driver may choose different thresholds to decide whether the throughput level * is low or medium or high based on variety of parameters like physical link * capacity of the current connection, the number of packets being dispatched * per second, etc. The throughput level events might not be consistent with the * actual current throughput value being observed. * * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput */ enum qca_wlan_throughput_level { QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, }; /** * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to * report throughput changes from the driver to user space. enum values are used * for netlink attributes sent with * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. */ enum qca_wlan_vendor_attr_throughput_change { QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, /* Indicates the direction of throughput in which the change is being * reported. u8 attribute. Value is 0 for TX and 1 for RX. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, /* Indicates the newly observed throughput level. enum * qca_wlan_throughput_level describes the possible range of values. * u8 attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, /* Indicates the driver's guidance on the new value to be set to * kernel's TCP parameter tcp_limit_output_bytes. u32 attribute. The * driver may optionally include this attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, /* Indicates the driver's guidance on the new value to be set to * kernel's TCP parameter tcp_adv_win_scale. s8 attribute. Possible * values are from -31 to 31. The driver may optionally include this * attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, /* Indicates the driver's guidance on the new value to be set to * kernel's TCP parameter tcp_delack_seg. u32 attribute. The driver may * optionally include this attribute. */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, /* keep last */ QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, }; /** * enum qca_coex_config_profiles - This enum defines different types of * traffic streams that can be prioritized one over the other during coex * scenarios. * The types defined in this enum are categorized in the below manner. * 0 - 31 values corresponds to WLAN * 32 - 63 values corresponds to BT * 64 - 95 values corresponds to Zigbee * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP * @QCA_BT_A2DP: Prioritize BT A2DP * @QCA_BT_BLE: Prioritize BT BLE * @QCA_BT_SCO: Prioritize BT SCO * @QCA_ZB_LOW: Prioritize Zigbee Low * @QCA_ZB_HIGH: Prioritize Zigbee High */ enum qca_coex_config_profiles { /* 0 - 31 corresponds to WLAN */ QCA_WIFI_STA_DISCOVERY = 0, QCA_WIFI_STA_CONNECTION = 1, QCA_WIFI_STA_CLASS_3_MGMT = 2, QCA_WIFI_STA_DATA = 3, QCA_WIFI_STA_ALL = 4, QCA_WIFI_SAP_DISCOVERY = 5, QCA_WIFI_SAP_CONNECTION = 6, QCA_WIFI_SAP_CLASS_3_MGMT = 7, QCA_WIFI_SAP_DATA = 8, QCA_WIFI_SAP_ALL = 9, /* 32 - 63 corresponds to BT */ QCA_BT_A2DP = 32, QCA_BT_BLE = 33, QCA_BT_SCO = 34, /* 64 - 95 corresponds to Zigbee */ QCA_ZB_LOW = 64, QCA_ZB_HIGH = 65 }; /** * enum qca_vendor_attr_coex_config - Specifies vendor coex config attributes * * @QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES: This attribute contains variable * length array of 8-bit values from enum qca_coex_config_profiles. * FW will prioritize the profiles in the order given in the array encapsulated * in this attribute. * For example: * ----------------------------------------------------------------------- * | 1 | 34 | 32 | 65 | * ----------------------------------------------------------------------- * If the attribute contains the values defined in above array then it means * 1) Wifi STA connection has priority over BT_SCO, BT_A2DP and ZIGBEE HIGH. * 2) BT_SCO has priority over BT_A2DP. * 3) BT_A2DP has priority over ZIGBEE HIGH. * Profiles which are not listed in this array shall not be preferred over the * profiles which are listed in the array as a part of this attribute. */ enum qca_vendor_attr_coex_config { QCA_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES = 1, /* Keep last */ QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST, QCA_VENDOR_ATTR_COEX_CONFIG_MAX = QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST - 1, }; /** * enum qca_wlan_vendor_attr_link_properties - Represent the link properties. * * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC address of the peer * (STA/AP) for the connected link. * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a * &struct nl80211_sta_flag_update for the respective connected link. MAC * address of the peer represented by * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. */ enum qca_wlan_vendor_attr_link_properties { QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, /* 1 - 3 are reserved */ QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, /* Keep last */ QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, QCA_VENDOR_ATTR_LINK_PROPERTIES_MAX = QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, }; #endif /* QCA_VENDOR_H */