.. SPDX-License-Identifier: CC-BY-SA-4.0 Miscellaneous ############# Fatal Error Default Handler =========================== The ``_CPU_Fatal_halt`` routine is the default fatal error handler. This routine copies _error into a known place - typically a stack location or a register, optionally disables interrupts, and halts/stops the CPU. It is prototyped as follows and is often implemented as a macro: .. code-block:: c void _CPU_Fatal_halt( unsigned32 _error ); CPU Context Validation ====================== The test case ``sptests/spcontext01`` ensures that the context switching and interrupt processing works. This test uses two support functions provided by the CPU port. These two functions are only used for this test and have no other purpose. .. code-block:: c void _CPU_Context_volatile_clobber( uintptr_t pattern ); void _CPU_Context_validate( uintptr_t pattern ); The ``_CPU_Context_volatile_clobber()`` function clobbers all volatile registers with values derived from the pattern parameter. This makes sure that the interrupt prologue code restores all volatile registers of the interrupted context. The ``_CPU_Context_validate()`` function initializes and validates the CPU context with values derived from the pattern parameter. This function will not return if the CPU context remains consistent. In case this function returns the CPU port is broken. The test uses two threads which concurrently validate the CPU context with a different patterns for each thread. This ensures that the context switching code works. Processor Endianness ==================== Endianness refers to the order in which numeric values are stored in memory by the microprocessor. Big endian architectures store the most significant byte of a multi-byte numeric value in the byte with the lowest address. This results in the hexadecimal value 0x12345678 being stored as 0x12345678 with 0x12 in the byte at offset zero, 0x34 in the byte at offset one, etc.. The Motorola M68K and numerous RISC processor families is big endian. Conversely, little endian architectures store the least significant byte of a multi-byte numeric value in the byte with the lowest address. This results in the hexadecimal value 0x12345678 being stored as 0x78563412 with 0x78 in the byte at offset zero, 0x56 in the byte at offset one, etc.. The Intel ix86 family is little endian. Interestingly, some CPU models within the PowerPC and MIPS architectures can be switched between big and little endian modes. Most embedded systems use these families strictly in big endian mode. RTEMS must be informed of the byte ordering for this microprocessor family and, optionally, endian conversion routines may be provided as part of the port. Conversion between endian formats is often necessary in multiprocessor environments and sometimes needed when interfacing with peripheral controllers. Specifying Processor Endianness ------------------------------- The ``CPU_BIG_ENDIAN`` and ``CPU_LITTLE_ENDIAN`` are set to specify the endian format used by this microprocessor. These macros should not be set to the same value. The following example illustrates how these macros should be set on a processor family that is big endian. .. code-block:: c #define CPU_BIG_ENDIAN TRUE #define CPU_LITTLE_ENDIAN FALSE The ``CPU_MPCI_RECEIVE_SERVER_EXTRA_STACK`` macro is set to the amount of stack space above the minimum thread stack space required by the MPCI Receive Server Thread. This macro is needed because in a multiprocessor system the MPCI Receive Server Thread must be able to process all directives. .. code-block:: c #define CPU_MPCI_RECEIVE_SERVER_EXTRA_STACK 0 Endian Swap Unsigned Integers ----------------------------- The port should provide routines to swap sixteen (``CPU_swap_u16``) and thirty-bit (``CPU_swap_u32``) unsigned integers. These are primarily used in two areas of RTEMS - multiprocessing support and the network endian swap routines. The ``CPU_swap_u32`` routine must be implemented as a static routine rather than a macro because its address is taken and used indirectly. On the other hand, the ``CPU_swap_u16`` routine may be implemented as a macro. Some CPUs have special instructions that swap a 32-bit quantity in a single instruction (e.g. i486). It is probably best to avoid an "endian swapping control bit" in the CPU. One good reason is that interrupts would probably have to be disabled to insure that an interrupt does not try to access the same "chunk" with the wrong endian. Another good reason is that on some CPUs, the endian bit endianness for ALL fetches - both code and data - so the code will be fetched incorrectly. The following is an implementation of the ``CPU_swap_u32`` routine that will work on any CPU. It operates by breaking the unsigned thirty-two bit integer into four byte-wide quantities and reassemblying them. .. code-block:: c static inline unsigned int CPU_swap_u32( unsigned int value ) { unsigned32 byte1, byte2, byte3, byte4, swapped; byte4 = (value >> 24) & 0xff; byte3 = (value >> 16) & 0xff; byte2 = (value >> 8) & 0xff; byte1 = value & 0xff; swapped = (byte1 << 24) | (byte2 << 16) | (byte3 << 8) | byte4; return( swapped ); } Although the above implementation is portable, it is not particularly efficient. So if there is a better way to implement this on a particular CPU family or model, please do so. The efficiency of this routine has significant impact on the efficiency of the multiprocessing support code in the shared memory driver and in network applications using the ntohl() family of routines. Most microprocessor families have rotate instructions which can be used to greatly improve the ``CPU_swap_u32`` routine. The most common way to do this is to: .. code-block:: c swap least significant two bytes with 16-bit rotate swap upper and lower 16-bits swap most significant two bytes with 16-bit rotate Some CPUs have special instructions that swap a 32-bit quantity in a single instruction (e.g. i486). It is probably best to avoid an "endian swapping control bit" in the CPU. One good reason is that interrupts would probably have to be disabled to insure that an interrupt does not try to access the same "chunk" with the wrong endian. Another good reason is that on some CPUs, the endian bit endianness for ALL fetches - both code and data - so the code will be fetched incorrectly. Similarly, here is a portable implementation of the ``CPU_swap_u16`` routine. Just as with the ``CPU_swap_u32`` routine, the porter should provide a better implementation if possible. .. code-block:: c #define CPU_swap_u16( value ) \\ (((value&0xff) << 8) | ((value >> 8)&0xff))