diff options
Diffstat (limited to 'bsd_eth_drivers/if_em/e1000_nvm.c')
| -rw-r--r-- | bsd_eth_drivers/if_em/e1000_nvm.c | 901 |
1 files changed, 901 insertions, 0 deletions
diff --git a/bsd_eth_drivers/if_em/e1000_nvm.c b/bsd_eth_drivers/if_em/e1000_nvm.c new file mode 100644 index 0000000..6fc4987 --- /dev/null +++ b/bsd_eth_drivers/if_em/e1000_nvm.c @@ -0,0 +1,901 @@ +/******************************************************************************* + + Copyright (c) 2001-2007, Intel Corporation + All rights reserved. + + Redistribution and use in source and binary forms, with or without + modification, are permitted provided that the following conditions are met: + + 1. Redistributions of source code must retain the above copyright notice, + this list of conditions and the following disclaimer. + + 2. Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in the + documentation and/or other materials provided with the distribution. + + 3. Neither the name of the Intel Corporation nor the names of its + contributors may be used to endorse or promote products derived from + this software without specific prior written permission. + + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + POSSIBILITY OF SUCH DAMAGE. + +*******************************************************************************/ +/*$FreeBSD: src/sys/dev/em/e1000_nvm.c,v 1.3 2007/05/16 00:14:23 jfv Exp $*/ + + +#include "e1000_api.h" +#include "e1000_nvm.h" + +/** + * e1000_raise_eec_clk - Raise EEPROM clock + * @hw: pointer to the HW structure + * @eecd: pointer to the EEPROM + * + * Enable/Raise the EEPROM clock bit. + **/ +static void +e1000_raise_eec_clk(struct e1000_hw *hw, u32 *eecd) +{ + *eecd = *eecd | E1000_EECD_SK; + E1000_WRITE_REG(hw, E1000_EECD, *eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(hw->nvm.delay_usec); +} + +/** + * e1000_lower_eec_clk - Lower EEPROM clock + * @hw: pointer to the HW structure + * @eecd: pointer to the EEPROM + * + * Clear/Lower the EEPROM clock bit. + **/ +static void +e1000_lower_eec_clk(struct e1000_hw *hw, u32 *eecd) +{ + *eecd = *eecd & ~E1000_EECD_SK; + E1000_WRITE_REG(hw, E1000_EECD, *eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(hw->nvm.delay_usec); +} + +/** + * e1000_shift_out_eec_bits - Shift data bits our to the EEPROM + * @hw: pointer to the HW structure + * @data: data to send to the EEPROM + * @count: number of bits to shift out + * + * We need to shift 'count' bits out to the EEPROM. So, the value in the + * "data" parameter will be shifted out to the EEPROM one bit at a time. + * In order to do this, "data" must be broken down into bits. + **/ +static void +e1000_shift_out_eec_bits(struct e1000_hw *hw, u16 data, u16 count) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + u32 mask; + + DEBUGFUNC("e1000_shift_out_eec_bits"); + + mask = 0x01 << (count - 1); + if (nvm->type == e1000_nvm_eeprom_microwire) + eecd &= ~E1000_EECD_DO; + else if (nvm->type == e1000_nvm_eeprom_spi) + eecd |= E1000_EECD_DO; + + do { + eecd &= ~E1000_EECD_DI; + + if (data & mask) + eecd |= E1000_EECD_DI; + + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + + usec_delay(nvm->delay_usec); + + e1000_raise_eec_clk(hw, &eecd); + e1000_lower_eec_clk(hw, &eecd); + + mask >>= 1; + } while (mask); + + eecd &= ~E1000_EECD_DI; + E1000_WRITE_REG(hw, E1000_EECD, eecd); +} + +/** + * e1000_shift_in_eec_bits - Shift data bits in from the EEPROM + * @hw: pointer to the HW structure + * @count: number of bits to shift in + * + * In order to read a register from the EEPROM, we need to shift 'count' bits + * in from the EEPROM. Bits are "shifted in" by raising the clock input to + * the EEPROM (setting the SK bit), and then reading the value of the data out + * "DO" bit. During this "shifting in" process the data in "DI" bit should + * always be clear. + **/ +static u16 +e1000_shift_in_eec_bits(struct e1000_hw *hw, u16 count) +{ + u32 eecd; + u32 i; + u16 data; + + DEBUGFUNC("e1000_shift_in_eec_bits"); + + eecd = E1000_READ_REG(hw, E1000_EECD); + + eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); + data = 0; + + for (i = 0; i < count; i++) { + data <<= 1; + e1000_raise_eec_clk(hw, &eecd); + + eecd = E1000_READ_REG(hw, E1000_EECD); + + eecd &= ~E1000_EECD_DI; + if (eecd & E1000_EECD_DO) + data |= 1; + + e1000_lower_eec_clk(hw, &eecd); + } + + return data; +} + +/** + * e1000_poll_eerd_eewr_done - Poll for EEPROM read/write completion + * @hw: pointer to the HW structure + * @ee_reg: EEPROM flag for polling + * + * Polls the EEPROM status bit for either read or write completion based + * upon the value of 'ee_reg'. + **/ +s32 +e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg) +{ + u32 attempts = 100000; + u32 i, reg = 0; + s32 ret_val = -E1000_ERR_NVM; + + DEBUGFUNC("e1000_poll_eerd_eewr_done"); + + for (i = 0; i < attempts; i++) { + if (ee_reg == E1000_NVM_POLL_READ) + reg = E1000_READ_REG(hw, E1000_EERD); + else + reg = E1000_READ_REG(hw, E1000_EEWR); + + if (reg & E1000_NVM_RW_REG_DONE) { + ret_val = E1000_SUCCESS; + break; + } + + usec_delay(5); + } + + return ret_val; +} + +/** + * e1000_acquire_nvm_generic - Generic request for access to EEPROM + * @hw: pointer to the HW structure + * + * Set the EEPROM access request bit and wait for EEPROM access grant bit. + * Return successful if access grant bit set, else clear the request for + * EEPROM access and return -E1000_ERR_NVM (-1). + **/ +s32 +e1000_acquire_nvm_generic(struct e1000_hw *hw) +{ + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + s32 timeout = E1000_NVM_GRANT_ATTEMPTS; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_acquire_nvm_generic"); + + E1000_WRITE_REG(hw, E1000_EECD, eecd | E1000_EECD_REQ); + eecd = E1000_READ_REG(hw, E1000_EECD); + + while (timeout) { + if (eecd & E1000_EECD_GNT) + break; + usec_delay(5); + eecd = E1000_READ_REG(hw, E1000_EECD); + timeout--; + } + + if (!timeout) { + eecd &= ~E1000_EECD_REQ; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + DEBUGOUT("Could not acquire NVM grant\n"); + ret_val = -E1000_ERR_NVM; + } + + return ret_val; +} + +/** + * e1000_standby_nvm - Return EEPROM to standby state + * @hw: pointer to the HW structure + * + * Return the EEPROM to a standby state. + **/ +static void +e1000_standby_nvm(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + + DEBUGFUNC("e1000_standby_nvm"); + + if (nvm->type == e1000_nvm_eeprom_microwire) { + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + + e1000_raise_eec_clk(hw, &eecd); + + /* Select EEPROM */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + + e1000_lower_eec_clk(hw, &eecd); + } else if (nvm->type == e1000_nvm_eeprom_spi) { + /* Toggle CS to flush commands */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + eecd &= ~E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + E1000_WRITE_FLUSH(hw); + usec_delay(nvm->delay_usec); + } +} + +/** + * e1000_stop_nvm - Terminate EEPROM command + * @hw: pointer to the HW structure + * + * Terminates the current command by inverting the EEPROM's chip select pin. + **/ +void +e1000_stop_nvm(struct e1000_hw *hw) +{ + u32 eecd; + + DEBUGFUNC("e1000_stop_nvm"); + + eecd = E1000_READ_REG(hw, E1000_EECD); + if (hw->nvm.type == e1000_nvm_eeprom_spi) { + /* Pull CS high */ + eecd |= E1000_EECD_CS; + e1000_lower_eec_clk(hw, &eecd); + } else if (hw->nvm.type == e1000_nvm_eeprom_microwire) { + /* CS on Microcwire is active-high */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + e1000_raise_eec_clk(hw, &eecd); + e1000_lower_eec_clk(hw, &eecd); + } +} + +/** + * e1000_release_nvm_generic - Release exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * Stop any current commands to the EEPROM and clear the EEPROM request bit. + **/ +void +e1000_release_nvm_generic(struct e1000_hw *hw) +{ + u32 eecd; + + DEBUGFUNC("e1000_release_nvm_generic"); + + e1000_stop_nvm(hw); + + eecd = E1000_READ_REG(hw, E1000_EECD); + eecd &= ~E1000_EECD_REQ; + E1000_WRITE_REG(hw, E1000_EECD, eecd); +} + +/** + * e1000_ready_nvm_eeprom - Prepares EEPROM for read/write + * @hw: pointer to the HW structure + * + * Setups the EEPROM for reading and writing. + **/ +static s32 +e1000_ready_nvm_eeprom(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 eecd = E1000_READ_REG(hw, E1000_EECD); + s32 ret_val = E1000_SUCCESS; + u16 timeout = 0; + u8 spi_stat_reg; + + DEBUGFUNC("e1000_ready_nvm_eeprom"); + + if (nvm->type == e1000_nvm_eeprom_microwire) { + /* Clear SK and DI */ + eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + /* Set CS */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, E1000_EECD, eecd); + } else if (nvm->type == e1000_nvm_eeprom_spi) { + /* Clear SK and CS */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + E1000_WRITE_REG(hw, E1000_EECD, eecd); + usec_delay(1); + timeout = NVM_MAX_RETRY_SPI; + + /* Read "Status Register" repeatedly until the LSB is cleared. + * The EEPROM will signal that the command has been completed + * by clearing bit 0 of the internal status register. If it's + * not cleared within 'timeout', then error out. */ + while (timeout) { + e1000_shift_out_eec_bits(hw, NVM_RDSR_OPCODE_SPI, + hw->nvm.opcode_bits); + spi_stat_reg = (u8)e1000_shift_in_eec_bits(hw, 8); + if (!(spi_stat_reg & NVM_STATUS_RDY_SPI)) + break; + + usec_delay(5); + e1000_standby_nvm(hw); + timeout--; + } + + if (!timeout) { + DEBUGOUT("SPI NVM Status error\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + } + +out: + return ret_val; +} + +/** + * e1000_read_nvm_spi - Read EEPROM's using SPI + * @hw: pointer to the HW structure + * @offset: offset of word in the EEPROM to read + * @words: number of words to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM. + **/ +s32 +e1000_read_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i = 0; + s32 ret_val; + u16 word_in; + u8 read_opcode = NVM_READ_OPCODE_SPI; + + DEBUGFUNC("e1000_read_nvm_spi"); + + /* A check for invalid values: offset too large, too many words, + * and not enough words. */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = e1000_acquire_nvm(hw); + if (ret_val) + goto out; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + e1000_standby_nvm(hw); + + if ((nvm->address_bits == 8) && (offset >= 128)) + read_opcode |= NVM_A8_OPCODE_SPI; + + /* Send the READ command (opcode + addr) */ + e1000_shift_out_eec_bits(hw, read_opcode, nvm->opcode_bits); + e1000_shift_out_eec_bits(hw, (u16)(offset*2), nvm->address_bits); + + /* Read the data. SPI NVMs increment the address with each byte + * read and will roll over if reading beyond the end. This allows + * us to read the whole NVM from any offset */ + for (i = 0; i < words; i++) { + word_in = e1000_shift_in_eec_bits(hw, 16); + data[i] = (word_in >> 8) | (word_in << 8); + } + +release: + e1000_release_nvm(hw); + +out: + return ret_val; +} + +/** + * e1000_read_nvm_microwire - Reads EEPROM's using microwire + * @hw: pointer to the HW structure + * @offset: offset of word in the EEPROM to read + * @words: number of words to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM. + **/ +s32 +e1000_read_nvm_microwire(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i = 0; + s32 ret_val; + u8 read_opcode = NVM_READ_OPCODE_MICROWIRE; + + DEBUGFUNC("e1000_read_nvm_microwire"); + + /* A check for invalid values: offset too large, too many words, + * and not enough words. */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = e1000_acquire_nvm(hw); + if (ret_val) + goto out; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + for (i = 0; i < words; i++) { + /* Send the READ command (opcode + addr) */ + e1000_shift_out_eec_bits(hw, read_opcode, nvm->opcode_bits); + e1000_shift_out_eec_bits(hw, (u16)(offset + i), + nvm->address_bits); + + /* Read the data. For microwire, each word requires the + * overhead of setup and tear-down. */ + data[i] = e1000_shift_in_eec_bits(hw, 16); + e1000_standby_nvm(hw); + } + +release: + e1000_release_nvm(hw); + +out: + return ret_val; +} + +/** + * e1000_read_nvm_eerd - Reads EEPROM using EERD register + * @hw: pointer to the HW structure + * @offset: offset of word in the EEPROM to read + * @words: number of words to read + * @data: word read from the EEPROM + * + * Reads a 16 bit word from the EEPROM using the EERD register. + **/ +s32 +e1000_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + u32 i, eerd = 0; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_read_nvm_eerd"); + + /* A check for invalid values: offset too large, too many words, + * and not enough words. */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + for (i = 0; i < words; i++) { + eerd = ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) + + E1000_NVM_RW_REG_START; + + E1000_WRITE_REG(hw, E1000_EERD, eerd); + ret_val = e1000_poll_eerd_eewr_done(hw, E1000_NVM_POLL_READ); + if (ret_val) + break; + + data[i] = (E1000_READ_REG(hw, E1000_EERD) >> E1000_NVM_RW_REG_DATA); + } + +out: + return ret_val; +} + +/** + * e1000_write_nvm_spi - Write to EEPROM using SPI + * @hw: pointer to the HW structure + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word(s) to be written to the EEPROM + * + * Writes data to EEPROM at offset using SPI interface. + * + * If e1000_update_nvm_checksum is not called after this function , the + * EEPROM will most likley contain an invalid checksum. + **/ +s32 +e1000_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + s32 ret_val; + u16 widx = 0; + + DEBUGFUNC("e1000_write_nvm_spi"); + + /* A check for invalid values: offset too large, too many words, + * and not enough words. */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = e1000_acquire_nvm(hw); + if (ret_val) + goto out; + + msec_delay(10); + + while (widx < words) { + u8 write_opcode = NVM_WRITE_OPCODE_SPI; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + e1000_standby_nvm(hw); + + /* Send the WRITE ENABLE command (8 bit opcode) */ + e1000_shift_out_eec_bits(hw, NVM_WREN_OPCODE_SPI, + nvm->opcode_bits); + + e1000_standby_nvm(hw); + + /* Some SPI eeproms use the 8th address bit embedded in the + * opcode */ + if ((nvm->address_bits == 8) && (offset >= 128)) + write_opcode |= NVM_A8_OPCODE_SPI; + + /* Send the Write command (8-bit opcode + addr) */ + e1000_shift_out_eec_bits(hw, write_opcode, nvm->opcode_bits); + e1000_shift_out_eec_bits(hw, (u16)((offset + widx) * 2), + nvm->address_bits); + + /* Loop to allow for up to whole page write of eeprom */ + while (widx < words) { + u16 word_out = data[widx]; + word_out = (word_out >> 8) | (word_out << 8); + e1000_shift_out_eec_bits(hw, word_out, 16); + widx++; + + if ((((offset + widx) * 2) % nvm->page_size) == 0) { + e1000_standby_nvm(hw); + break; + } + } + } + + msec_delay(10); +release: + e1000_release_nvm(hw); + +out: + return ret_val; +} + +/** + * e1000_write_nvm_microwire - Writes EEPROM using microwire + * @hw: pointer to the HW structure + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word(s) to be written to the EEPROM + * + * Writes data to EEPROM at offset using microwire interface. + * + * If e1000_update_nvm_checksum is not called after this function , the + * EEPROM will most likley contain an invalid checksum. + **/ +s32 +e1000_write_nvm_microwire(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + s32 ret_val; + u32 eecd; + u16 words_written = 0; + u16 widx = 0; + + DEBUGFUNC("e1000_write_nvm_microwire"); + + /* A check for invalid values: offset too large, too many words, + * and not enough words. */ + if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + ret_val = e1000_acquire_nvm(hw); + if (ret_val) + goto out; + + ret_val = e1000_ready_nvm_eeprom(hw); + if (ret_val) + goto release; + + e1000_shift_out_eec_bits(hw, NVM_EWEN_OPCODE_MICROWIRE, + (u16)(nvm->opcode_bits + 2)); + + e1000_shift_out_eec_bits(hw, 0, (u16)(nvm->address_bits - 2)); + + e1000_standby_nvm(hw); + + while (words_written < words) { + e1000_shift_out_eec_bits(hw, NVM_WRITE_OPCODE_MICROWIRE, + nvm->opcode_bits); + + e1000_shift_out_eec_bits(hw, (u16)(offset + words_written), + nvm->address_bits); + + e1000_shift_out_eec_bits(hw, data[words_written], 16); + + e1000_standby_nvm(hw); + + for (widx = 0; widx < 200; widx++) { + eecd = E1000_READ_REG(hw, E1000_EECD); + if (eecd & E1000_EECD_DO) + break; + usec_delay(50); + } + + if (widx == 200) { + DEBUGOUT("NVM Write did not complete\n"); + ret_val = -E1000_ERR_NVM; + goto release; + } + + e1000_standby_nvm(hw); + + words_written++; + } + + e1000_shift_out_eec_bits(hw, NVM_EWDS_OPCODE_MICROWIRE, + (u16)(nvm->opcode_bits + 2)); + + e1000_shift_out_eec_bits(hw, 0, (u16)(nvm->address_bits - 2)); + +release: + e1000_release_nvm(hw); + +out: + return ret_val; +} + +/** + * e1000_read_part_num_generic - Read device part number + * @hw: pointer to the HW structure + * @part_num: pointer to device part number + * + * Reads the product board assembly (PBA) number from the EEPROM and stores + * the value in part_num. + **/ +s32 +e1000_read_part_num_generic(struct e1000_hw *hw, u32 *part_num) +{ + s32 ret_val; + u16 nvm_data; + + DEBUGFUNC("e1000_read_part_num_generic"); + + ret_val = e1000_read_nvm(hw, NVM_PBA_OFFSET_0, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + *part_num = (u32)(nvm_data << 16); + + ret_val = e1000_read_nvm(hw, NVM_PBA_OFFSET_1, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + *part_num |= nvm_data; + +out: + return ret_val; +} + +/** + * e1000_read_mac_addr_generic - Read device MAC address + * @hw: pointer to the HW structure + * + * Reads the device MAC address from the EEPROM and stores the value. + * Since devices with two ports use the same EEPROM, we increment the + * last bit in the MAC address for the second port. + **/ +s32 +e1000_read_mac_addr_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 offset, nvm_data, i; + + DEBUGFUNC("e1000_read_mac_addr"); + + for (i = 0; i < ETH_ADDR_LEN; i += 2) { + offset = i >> 1; + ret_val = e1000_read_nvm(hw, offset, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF); + hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8); + } + + /* Flip last bit of mac address if we're on second port */ + if (hw->bus.func == E1000_FUNC_1) + hw->mac.perm_addr[5] ^= 1; + + for (i = 0; i < ETH_ADDR_LEN; i++) + hw->mac.addr[i] = hw->mac.perm_addr[i]; + +out: + return ret_val; +} + +/** + * e1000_validate_nvm_checksum_generic - Validate EEPROM checksum + * @hw: pointer to the HW structure + * + * Calculates the EEPROM checksum by reading/adding each word of the EEPROM + * and then verifies that the sum of the EEPROM is equal to 0xBABA. + **/ +s32 +e1000_validate_nvm_checksum_generic(struct e1000_hw *hw) +{ + s32 ret_val = E1000_SUCCESS; + u16 checksum = 0; + u16 i, nvm_data; + + DEBUGFUNC("e1000_validate_nvm_checksum_generic"); + + for (i = 0; i < (NVM_CHECKSUM_REG + 1); i++) { + ret_val = e1000_read_nvm(hw, i, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + goto out; + } + checksum += nvm_data; + } + + if (checksum != (u16) NVM_SUM) { + DEBUGOUT("NVM Checksum Invalid\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + +out: + return ret_val; +} + +/** + * e1000_update_nvm_checksum_generic - Update EEPROM checksum + * @hw: pointer to the HW structure + * + * Updates the EEPROM checksum by reading/adding each word of the EEPROM + * up to the checksum. Then calculates the EEPROM checksum and writes the + * value to the EEPROM. + **/ +s32 +e1000_update_nvm_checksum_generic(struct e1000_hw *hw) +{ + s32 ret_val; + u16 checksum = 0; + u16 i, nvm_data; + + DEBUGFUNC("e1000_update_nvm_checksum"); + + for (i = 0; i < NVM_CHECKSUM_REG; i++) { + ret_val = e1000_read_nvm(hw, i, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error while updating checksum.\n"); + goto out; + } + checksum += nvm_data; + } + checksum = (u16) NVM_SUM - checksum; + ret_val = e1000_write_nvm(hw, NVM_CHECKSUM_REG, 1, &checksum); + if (ret_val) { + DEBUGOUT("NVM Write Error while updating checksum.\n"); + } + +out: + return ret_val; +} + +/** + * e1000_reload_nvm_generic - Reloads EEPROM + * @hw: pointer to the HW structure + * + * Reloads the EEPROM by setting the "Reinitialize from EEPROM" bit in the + * extended control register. + **/ +void +e1000_reload_nvm_generic(struct e1000_hw *hw) +{ + u32 ctrl_ext; + + DEBUGFUNC("e1000_reload_nvm_generic"); + + usec_delay(10); + ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); +} + +/* Function pointers local to this file and not intended for public use */ + +/** + * e1000_acquire_nvm - Acquire exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * For those silicon families which have implemented a NVM acquire function, + * run the defined function else return success. + **/ +s32 +e1000_acquire_nvm(struct e1000_hw *hw) +{ + if (hw->func.acquire_nvm != NULL) + return hw->func.acquire_nvm(hw); + else + return E1000_SUCCESS; +} + +/** + * e1000_release_nvm - Release exclusive access to EEPROM + * @hw: pointer to the HW structure + * + * For those silicon families which have implemented a NVM release function, + * run the defined fucntion else return success. + **/ +void +e1000_release_nvm(struct e1000_hw *hw) +{ + if (hw->func.release_nvm != NULL) + hw->func.release_nvm(hw); +} + |